Juliet Kim says:

====================
Support both XIVE and XICS modes in ibmvnic

This series aims to support both XICS and XIVE with avoiding
a regression in behavior when a system runs in XICS mode.

Patch 1 reverts commit 11d49ce9
(“net/ibmvnic: Fix EOI when running in XIVE mode.”)

Patch 2 Ignore H_FUNCTION return from H_EOI to tolerate XIVE mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Reversion of commit 11d49ce9
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) leaves us
calling H_EOI even in XIVE mode. That will fail with H_FUNCTION
because H_EOI is not supported in that mode. That failure is
harmless. Ignore it so we can use common code for both XICS and
XIVE.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 11d49ce9
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) since that
has the unintended effect of changing the interrupt priority
and emits warning when running in legacy XICS mode.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: fixes 2019-11-20

please apply two late qeth fixes to your net tree.

The first fixes a deadlock that can occur if a qeth device is set
offline while in the middle of processing deferred HW events.
The second patch converts the return value of an error path to
use -EIO, so that it can be passed back to userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When propagating IO errors back to userspace, one error path in
qeth_irq() currently returns '1' instead of a proper errno.

Fixes: 54daaca7 ("s390/qeth: cancel cmd on early error")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The L2 bridgeport code uses the coarse 'conf_mutex' for guarding access
to its configuration state.
This can result in a deadlock when qeth_l2_stop_card() - called under the
conf_mutex - blocks on flush_workqueue() to wait for the completion of
pending bridgeport workers. Such workers would also need to aquire
the conf_mutex, stalling indefinitely.

Introduce a lock that specifically guards the bridgeport configuration,
so that the workers no longer need the conf_mutex.
Wrapping qeth_l2_promisc_to_bridge() in this fine-grained lock then also
fixes a theoretical race against a concurrent qeth_bridge_port_role_store()
operation.

Fixes: c0a2e4d1 ("s390/qeth: conclude all event processing before offlining a card")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously we will return directly if (!rt || !rt->fib6_nh.fib_nh_gw_family)
in function rt6_probe(), but after commit cc3a86c8
("ipv6: Change rt6_probe to take a fib6_nh"), the logic changed to
return if there is fib_nh_gw_family.

Fixes: cc3a86c8 ("ipv6: Change rt6_probe to take a fib6_nh")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kobject_init_and_add takes reference even when it fails. This has
to be given up by the caller in error handling. Otherwise memory
allocated by kobject_init_and_add is never freed. Originally found
by Syzkaller:

BUG: memory leak
unreferenced object 0xffff8880679f8b08 (size 8):
  comm "netdev_register", pid 269, jiffies 4294693094 (age 12.132s)
  hex dump (first 8 bytes):
    72 78 2d 30 00 36 20 d4                          rx-0.6 .
  backtrace:
    [<000000008c93818e>] __kmalloc_track_caller+0x16e/0x290
    [<000000001f2e4e49>] kvasprintf+0xb1/0x140
    [<000000007f313394>] kvasprintf_const+0x56/0x160
    [<00000000aeca11c8>] kobject_set_name_vargs+0x5b/0x140
    [<0000000073a0367c>] kobject_init_and_add+0xd8/0x170
    [<0000000088838e4b>] net_rx_queue_update_kobjects+0x152/0x560
    [<000000006be5f104>] netdev_register_kobject+0x210/0x380
    [<00000000e31dab9d>] register_netdevice+0xa1b/0xf00
    [<00000000f68b2465>] __tun_chr_ioctl+0x20d5/0x3dd0
    [<000000004c50599f>] tun_chr_ioctl+0x2f/0x40
    [<00000000bbd4c317>] do_vfs_ioctl+0x1c7/0x1510
    [<00000000d4c59e8f>] ksys_ioctl+0x99/0xb0
    [<00000000946aea81>] __x64_sys_ioctl+0x78/0xb0
    [<0000000038d946e5>] do_syscall_64+0x16f/0x580
    [<00000000e0aa5d8f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<00000000285b3d1a>] 0xffffffffffffffff

Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 1d463956 ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled.  E.g. on
r7s72100/rskrza1:

    sh-eth e8203000.ethernet: MDIO init failed: -524
    sh-eth: probe of e8203000.ethernet failed with error -524

Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.

Fixes: 1d463956 ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 075e238d.

Going to go with Geert's fix instead, which also has a
correct Fixes tag.
Signed-off-by: David S. Miller <davem@davemloft.net>

According to hardware user manual, bits5~7 in register
HCLGE_MISC_VECTOR_INT_STS means reset interrupts status,
but HCLGE_RESET_INT_M is defined as bits0~2 now. So it
will make hclge_reset_err_handle() read the wrong reset
interrupt status.

This patch fixes this wrong bit mask.

Fixes: 2336f19d ("net: hns3: check reset interrupt status when reset fails")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)

Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)

Then it is fine to disable clks without causing clock count mis-match.

Fixes: c43eab3e ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

when configuring act_pedit rules, the number of keys is validated only on
addition of a new entry. This is not sufficient to avoid hitting a WARN()
in the traffic path: for example, it is possible to replace a valid entry
with a new one having 0 extended keys, thus causing splats in dmesg like:

 pedit BUG: index 42
 WARNING: CPU: 2 PID: 4054 at net/sched/act_pedit.c:410 tcf_pedit_act+0xc84/0x1200 [act_pedit]
 [...]
 RIP: 0010:tcf_pedit_act+0xc84/0x1200 [act_pedit]
 Code: 89 fa 48 c1 ea 03 0f b6 04 02 84 c0 74 08 3c 03 0f 8e ac 00 00 00 48 8b 44 24 10 48 c7 c7 a0 c4 e4 c0 8b 70 18 e8 1c 30 95 ea <0f> 0b e9 a0 fa ff ff e8 00 03 f5 ea e9 14 f4 ff ff 48 89 58 40 e9
 RSP: 0018:ffff888077c9f320 EFLAGS: 00010286
 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffac2983a2
 RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff888053927bec
 RBP: dffffc0000000000 R08: ffffed100a726209 R09: ffffed100a726209
 R10: 0000000000000001 R11: ffffed100a726208 R12: ffff88804beea780
 R13: ffff888079a77400 R14: ffff88804beea780 R15: ffff888027ab2000
 FS:  00007fdeec9bd740(0000) GS:ffff888053900000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007ffdb3dfd000 CR3: 000000004adb4006 CR4: 00000000001606e0
 Call Trace:
  tcf_action_exec+0x105/0x3f0
  tcf_classify+0xf2/0x410
  __dev_queue_xmit+0xcbf/0x2ae0
  ip_finish_output2+0x711/0x1fb0
  ip_output+0x1bf/0x4b0
  ip_send_skb+0x37/0xa0
  raw_sendmsg+0x180c/0x2430
  sock_sendmsg+0xdb/0x110
  __sys_sendto+0x257/0x2b0
  __x64_sys_sendto+0xdd/0x1b0
  do_syscall_64+0xa5/0x4e0
  entry_SYSCALL_64_after_hwframe+0x49/0xbe
 RIP: 0033:0x7fdeeb72e993
 Code: 48 8b 0d e0 74 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 0d d6 2c 00 00 75 13 49 89 ca b8 2c 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 34 c3 48 83 ec 08 e8 4b cc 00 00 48 89 04 24
 RSP: 002b:00007ffdb3de8a18 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
 RAX: ffffffffffffffda RBX: 000055c81972b700 RCX: 00007fdeeb72e993
 RDX: 0000000000000040 RSI: 000055c81972b700 RDI: 0000000000000003
 RBP: 00007ffdb3dea130 R08: 000055c819728510 R09: 0000000000000010
 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
 R13: 000055c81972b6c0 R14: 000055c81972969c R15: 0000000000000080

Fix this moving the check on 'nkeys' earlier in tcf_pedit_init(), so that
attempts to install rules having 0 keys are always rejected with -EINVAL.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modifying the link settings via phylink_ethtool_ksettings_set() and
phylink_ethtool_set_pauseparam() didn't always work as intended for
PHY based setups, as calling phylink_mac_config() would result in the
unresolved configuration being committed to the MAC, rather than the
configuration with the speed and duplex setting.

This would work fine if the update caused the link to renegotiate,
but if no settings have changed, phylib won't trigger a renegotiation
cycle, and the MAC will be left incorrectly configured.

Avoid calling phylink_mac_config() unless we are using an inband mode
in phylink_ethtool_ksettings_set(), and use phy_set_asym_pause() as
introduced in 4.20 to set the PHY settings in
phylink_ethtool_set_pauseparam().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the documentation on phylink's create and destroy functions to
explicitly state that the rtnl lock must not be held while calling
these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

During performance testing, I found that one of my r8169 NICs suffered
a major performance loss, a 8168c model.

Running netperf's TCP_STREAM test didn't return the expected
throughput of > 900 Mb/s, but rather only about 22 Mb/s.  Strange
enough, running the TCP_MAERTS and UDP_STREAM tests all returned with
throughput > 900 Mb/s, as did TCP_STREAM with the other r8169 NICs I can
test (either one of 8169s, 8168e, 8168f).

Bisecting turned up commit 93681cd7,
"r8169: enable HW csum and TSO" as the culprit.

I added my 8168c version, RTL_GIGA_MAC_VER_22, to the code
special-casing the 8168evl as per the patch below.  This fixed the
performance problem for me.

Fixes: 93681cd7 ("r8169: enable HW csum and TSO")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I prefer to use my personal email address for kernel related work.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Rain River <rain.1986.08.12@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The taprio qdisc allows to set mqprio setting but only once. In case
if mqprio settings are provided next time the error is returned as
it's not allowed to change traffic class mapping in-flignt and that
is normal. But if configuration is absolutely the same - no need to
return error. It allows to provide same command couple times,
changing only base time for instance, or changing only scheds maps,
but leaving mqprio setting w/o modification. It more corresponds the
message: "Changing the traffic mapping of a running schedule is not
supported", so reject mqprio if it's really changed.

Also corrected TC_BITMASK + 1 for consistency, as proposed.

Fixes: a3d43c0d ("taprio: Add support adding an admin schedule")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bring back tls_sw_sendpage_locked. sk_msg redirection into a socket
with TLS_TX takes the following path:

  tcp_bpf_sendmsg_redir
    tcp_bpf_push_locked
      tcp_bpf_push
        kernel_sendpage_locked
          sock->ops->sendpage_locked

Also update the flags test in tls_sw_sendpage_locked to allow flag
MSG_NO_SHARED_FRAGS. bpf_tcp_sendmsg sets this.

Link: https://lore.kernel.org/netdev/CA+FuTSdaAawmZ2N8nfDDKu3XLpXBbMtcCT0q4FntDD2gn8ASUw@mail.gmail.com/T/#t
Link: https://github.com/wdebruij/kerneltools/commits/icept.2
Fixes: 0608c69c ("bpf: sk_msg, sock{map|hash} redirect through ULP")
Fixes: f3de19af ("Revert \"net/tls: remove unused function tls_sw_sendpage_locked\"")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous commit had a bug where the last page in the memory range
could not be synced. This change fixes the behavior so that all the
required pages are synced.

Fixes: 9cfeeb57 ("gve: Fixes DMA synchronization")
Signed-off-by: Adi Suresh <adisuresh@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_RESET_CONTROLLER is disabled, the
devm_reset_control_get_exclusive function returns -ENOTSUPP. This is not
handled in subsequent check and then the mdio device fails to probe.

When CONFIG_RESET_CONTROLLER is enabled, its code checks in OF for reset
device, and since it is not present, returns -ENOENT. -ENOENT is handled.
Add -ENOTSUPP also.

This happened to me when upgrading kernel on Turris Omnia. You either
have to enable CONFIG_RESET_CONTROLLER or use this patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 71dd6c0d ("net: phy: add support for reset-controller")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit eec4844f ("proc/sysctl: add shared variables for range
check") did:
-               .extra2         = &two,
+               .extra2         = SYSCTL_ONE,
here, which doesn't seem to be intentional, given the changelog.
This patch restores it to the previous, as the value of 2 still makes
sense (used in fib_multipath_hash()).

Fixes: eec4844f ("proc/sysctl: add shared variables for range check")
Cc: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver forgets to disable the regulator in remove like what is done
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

XDP_TX rings should not be limited by max_num_tx_rings_p_up.
To make sure total number of TX rings never exceed MAX_TX_RINGS,
add similar check in mlx4_en_alloc_tx_queue_per_tc(), where
a new value is assigned for num_up.

Fixes: 7e1dc5e9 ("net/mlx4_en: Limit the number of TX rings")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

info->options_len is 'u8' type, and when opts_len with a value >
IP_TUNNEL_OPTS_MAX, 'info->options_len = opts_len' will cast int
to u8 and set a wrong value to info->options_len.

Kernel crashed in my test when doing:

  # opts="0102:80:00800022"
  # for i in {1..99}; do opts="$opts,0102:80:00800022"; done
  # ip link add name geneve0 type geneve dstport 0 external
  # tc qdisc add dev eth0 ingress
  # tc filter add dev eth0 protocol ip parent ffff: \
       flower indev eth0 ip_proto udp action tunnel_key \
       set src_ip 10.0.99.192 dst_ip 10.0.99.193 \
       dst_port 6081 id 11 geneve_opts $opts \
       action mirred egress redirect dev geneve0

So we should do the similar check as cls_flower does, return error
when opts_len > IP_TUNNEL_OPTS_MAX in tunnel_key_copy_opts().

Fixes: 0ed5269f ("net/sched: add tunnel option support to act_tunnel_key")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The helper mlxsw_sp_ipip_dev_ul_tb_id() determines the underlay VRF of a
GRE tunnel. For a tunnel without a bound device, it uses the same VRF that
the tunnel is in. However in Linux, a GRE tunnel without a bound device
uses the main VRF as the underlay. Fix the function accordingly.

mlxsw further assumed that moving a tunnel to a different VRF could cause
conflict in local tunnel endpoint address, which cannot be offloaded.
However, the only way that an underlay could be changed by moving the
tunnel device itself is if the tunnel device does not have a bound device.
But in that case the underlay is always the main VRF, so there is no
opportunity to introduce a conflict by moving such device. Thus this check
constitutes a dead code, and can be removed, which do.

Fixes: 6ddb7426 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of errors in unlink_clip_vcc, the logging level is set to
pr_crit but failures in clip_setentry are handled by pr_err().
The patch changes the severity consistent across invocations.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool expects ETHTOOL_GRXCLSRLALL to set ethtool_rxnfc->data with the
total number of entries in the rx classifier table.  Surprisingly, mlx4
is missing this part (in principle ethtool could still move forward and
try the insert).

Tested: compiled and run command:
	phh13:~# ethtool -N eth1 flow-type udp4  queue 4
	Added rule with ID 255
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>

Daniel Borkmann says:

====================
pull-request: bpf 2019-11-15

The following pull-request contains BPF updates for your *net* tree.

We've added 1 non-merge commits during the last 9 day(s) which contain
a total of 1 file changed, 3 insertions(+), 1 deletion(-).

The main changes are:

1) Fix a missing unlock of bpf_devs_lock in bpf_offload_dev_create()'s
    error path, from Dan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull crypto fix from Herbert Xu:
 "This reverts a number of changes to the khwrng thread which feeds the
  kernel random number pool from hwrng drivers. They were trying to fix
  issues with suspend-and-resume but ended up causing regressions"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  Revert "hwrng: core - Freeze khwrng thread during suspend"

This reverts commit 03a3bb7a ("hwrng: core - Freeze khwrng
thread during suspend"), ff296293 ("random: Support freezable
kthreads in add_hwgenerator_randomness()") and 59b56948 ("random:
Use wait_event_freezable() in add_hwgenerator_randomness()").

These patches introduced regressions and we need more time to
get them ready for mainline.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Pull x86 fixes from Ingo Molnar:
 "Two fixes: disable unreliable HPET on Intel Coffe Lake platforms, and
  fix a lockdep splat in the resctrl code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/resctrl: Fix potential lockdep warning
  x86/quirks: Disable HPET on Intel Coffe Lake platforms

Pull timer fix from Ingo Molnar:
 "Fix integer truncation bug in __do_adjtimex()"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ntp/y2038: Remove incorrect time_t truncation

Pull perf fixes from Ingo Molnar:
 "Misc fixes: a handful of AUX event handling related fixes, a Sparse
  fix and two ABI fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix missing static inline on perf_cgroup_switch()
  perf/core: Consistently fail fork on allocation failures
  perf/aux: Disallow aux_output for kernel events
  perf/core: Reattach a misplaced comment
  perf/aux: Fix the aux_output group inheritance fix
  perf/core: Disallow uncore-cgroup events

Pull networking fixes from David Miller:

 1) Fix memory leak in xfrm_state code, from Steffen Klassert.

 2) Fix races between devlink reload operations and device
    setup/cleanup, from Jiri Pirko.

 3) Null deref in NFC code, from Stephan Gerhold.

 4) Refcount fixes in SMC, from Ursula Braun.

 5) Memory leak in slcan open error paths, from Jouni Hogander.

 6) Fix ETS bandwidth validation in hns3, from Yonglong Liu.

 7) Info leak on short USB request answers in ax88172a driver, from
    Oliver Neukum.

 8) Release mem region properly in ep93xx_eth, from Chuhong Yuan.

 9) PTP config timestamp flags validation, from Richard Cochran.

10) Dangling pointers after SKB data realloc in seg6, from Andrea Mayer.

11) Missing free_netdev() in gemini driver, from Chuhong Yuan.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (56 commits)
  ipmr: Fix skb headroom in ipmr_get_route().
  net: hns3: cleanup of stray struct hns3_link_mode_mapping
  net/smc: fix fastopen for non-blocking connect()
  rds: ib: update WR sizes when bringing up connection
  net: gemini: add missed free_netdev
  net: dsa: tag_8021q: Fix dsa_8021q_restore_pvid for an absent pvid
  seg6: fix skb transport_header after decap_and_validate()
  seg6: fix srh pointer in get_srh()
  net: stmmac: Use the correct style for SPDX License Identifier
  octeontx2-af: Use the correct style for SPDX License Identifier
  ptp: Extend the test program to check the external time stamp flags.
  mlx5: Reject requests to enable time stamping on both edges.
  igb: Reject requests that fail to enable time stamping on both edges.
  dp83640: Reject requests to enable time stamping on both edges.
  mv88e6xxx: Reject requests to enable time stamping on both edges.
  ptp: Introduce strict checking of external time stamp options.
  renesas: reject unsupported external timestamp flags
  mlx5: reject unsupported external timestamp flags
  igb: reject unsupported external timestamp flags
  dp83640: reject unsupported external timestamp flags
  ...

In route.c, inet_rtm_getroute_build_skb() creates an skb with no
headroom. This skb is then used by inet_rtm_getroute() which may pass
it to rt_fill_info() and, from there, to ipmr_get_route(). The later
might try to reuse this skb by cloning it and prepending an IPv4
header. But since the original skb has no headroom, skb_push() triggers
skb_under_panic():

skbuff: skb_under_panic: text:00000000ca46ad8a len:80 put:20 head:00000000cd28494e data:000000009366fd6b tail:0x3c end:0xec0 dev:veth0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:108!
invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 6 PID: 587 Comm: ip Not tainted 5.4.0-rc6+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
RIP: 0010:skb_panic+0xbf/0xd0
Code: 41 a2 ff 8b 4b 70 4c 8b 4d d0 48 c7 c7 20 76 f5 8b 44 8b 45 bc 48 8b 55 c0 48 8b 75 c8 41 54 41 57 41 56 41 55 e8 75 dc 7a ff <0f> 0b 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00
RSP: 0018:ffff888059ddf0b0 EFLAGS: 00010286
RAX: 0000000000000086 RBX: ffff888060a315c0 RCX: ffffffff8abe4822
RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffff88806c9a79cc
RBP: ffff888059ddf118 R08: ffffed100d9361b1 R09: ffffed100d9361b0
R10: ffff88805c68aee3 R11: ffffed100d9361b1 R12: ffff88805d218000
R13: ffff88805c689fec R14: 000000000000003c R15: 0000000000000ec0
FS:  00007f6af184b700(0000) GS:ffff88806c980000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffc8204a000 CR3: 0000000057b40006 CR4: 0000000000360ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 skb_push+0x7e/0x80
 ipmr_get_route+0x459/0x6fa
 rt_fill_info+0x692/0x9f0
 inet_rtm_getroute+0xd26/0xf20
 rtnetlink_rcv_msg+0x45d/0x630
 netlink_rcv_skb+0x1a5/0x220
 rtnetlink_rcv+0x15/0x20
 netlink_unicast+0x305/0x3a0
 netlink_sendmsg+0x575/0x730
 sock_sendmsg+0xb5/0xc0
 ___sys_sendmsg+0x497/0x4f0
 __sys_sendmsg+0xcb/0x150
 __x64_sys_sendmsg+0x48/0x50
 do_syscall_64+0xd2/0xac0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Actually the original skb used to have enough headroom, but the
reserve_skb() call was lost with the introduction of
inet_rtm_getroute_build_skb() by commit 404eb77e ("ipv4: support
sport, dport and ip_proto in RTM_GETROUTE").

We could reserve some headroom again in inet_rtm_getroute_build_skb(),
but this function shouldn't be responsible for handling the special
case of ipmr_get_route(). Let's handle that directly in
ipmr_get_route() by calling skb_realloc_headroom() instead of
skb_clone().

Fixes: 404eb77e ("ipv4: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans-up the stray left over code. It has no
functionality impact.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FASTOPEN does not work with SMC-sockets. Since SMC allows fallback to
TCP native during connection start, the FASTOPEN setsockopts trigger
this fallback, if the SMC-socket is still in state SMC_INIT.
But if a FASTOPEN setsockopt is called after a non-blocking connect(),
this is broken, and fallback does not make sense.
This change complements
commit cd206360 ("net/smc: avoid fallback in case of non-blocking connect")
and fixes the syzbot reported problem "WARNING in smc_unhash_sk".

Reported-by: syzbot+8488cc4cf1c9e09b8b86@syzkaller.appspotmail.com
Fixes: e1bbdd57 ("net/smc: reduce sock_put() for fallback sockets")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently WR sizes are updated from rds_ib_sysctl_max_send_wr and
rds_ib_sysctl_max_recv_wr when a connection is shut down. As a result,
a connection being down while rds_ib_sysctl_max_send_wr or
rds_ib_sysctl_max_recv_wr are updated, will not update the sizes when
it comes back up.

Move resizing of WRs to rds_ib_setup_qp so that connections will be setup
with the most current WR sizes.
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver forgets to free allocated netdev in remove like
what is done in probe failure.
Add the free to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>