Since we will want to remove the wdev lock in the future,
lock the wiphy here to iterate and for checking the status
of the connections.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since we will want to remove the wdev lock in the future,
lock the wiphy here to iterate and check the flags.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Check that we hold the wiphy mutex in the ops when
calling the driver, since we're now on our way to
always hold it, and simplify the locking.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Again this should be per link and will get cancellation
issues, move it to a wiphy work.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This work should be made per link as well, and then
will have cancellation issues. Moving it to a wiphy
work already fixes those beforehand.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This again is intended for future cleanups that are
possible when mac80211 and drivers can assume the
wiphy is locked.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

One more work that will now execute with the wiphy
locked, for future cleanups.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This way we hold the wiphy mutex there, as a step towards
removing some of the additional locks we have.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Again, to have the wiphy locked for it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This also has the wiphy locked here then. We need to use
the _locked version of cfg80211_sched_scan_stopped() now,
which also fixes an old deadlock there.

Fixes: a05829a7 ("cfg80211: avoid holding the RTNL when calling the driver")
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Along with everything else, move the dynamic PS work
to be a wiphy work, to simplify locking later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We want to have the wiphy locked for these as well,
so move it to be a wiphy work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Make the offchannel works wiphy works to have the
wiphy locked for executing them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Lock the wiphy in the IP address notifier as another
place that should have it locked before calling into
the driver. This needs a bit of attention since the
notifier can be called while the wiphy is already
locked, when we remove an interface. Handle this by
not running the notifier in this case, and instead
calling out to the driver directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Again this serves to simplify the locking in mac80211
in the future, since this is a relatively complex work.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Move the scan work to wiphy work, which also simplifies
the way we handle the work vs. the scan configuration.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Move the radar detect work to wiphy work in order
to lock the wiphy for it without doing it manually.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Move the DFS CAC work over to hold the wiphy lock
there without worry about work cancellation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add more might_sleep() checks and check sdata-in-driver
for one additional place.

type=feature
ticket=jira:WIFI-314309
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Convert the A-MPDU work to wiphy work so it holds the
wiphy mutex and we can later guarantee that to drivers.
It might seem that we could run these concurrently for
different stations, but they're all on the ordered
mac80211 workqueue, so this shouldn't matter for that.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Before converting more works to wiphy work, add
flushing in mac80211 where we also flush the
mac80211 workqueue. Not needed in suspend since
cfg80211 will have taken care of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There may be sometimes reasons to actually run the work
if it's pending, add flush functions for both regular and
delayed wiphy work that will do this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a new "for_each_rdev()" macro and check that we
hold the RTNL when calling it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To change aggregation status may call into the driver,
lock the wiphy for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

It's no longer really needed to ensure that the debugfs
file isn't going away, debugfs handles that. So there's
no point in holding dev_base_lock or RTNL here, but we
should instead hold the wiphy lock since drivers will
be allowed to depend on that. Do that, which requires
splitting the sdata and link macros a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since we no longer really use the RTNL, there's no point
in locking it here. Most drivers don't really need to
have any locks here anyway, and the rest are probably
completely broken, but it's a debugfs-only callback so
it really doesn't matter much.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The current SMPS status handling isn't per link, so we only
ever change the deflink, which is obviously wrong, it's not
even used for multi-link connections, but the request API
actually includes the link ID.

Use the new status_data changes to move the handling to the
right link, this also saves parsing the frame again on the
status report, instead we can now check only if it was an
SMPS frame.

Of course, move the worker to be a wiphy work so that we're
able to cancel it safely for the link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When the connection is a MLO connection, a SMPS request should be
sent on a specific link, as SMPS is BSS specific, and the DA and BSSID
used for the action frame transmission should be the AP MLD address, as
the underlying driver is expected to perform the address translation
(based on the link ID).

Fix the SMPS request handling to use the AP MLD address and provide the
link ID for the request processing during Tx.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Take one more free bit to indicate it's IDR vs. internal
usage, to be able to carve out some bits here for other
internal usage, other than IDR handling with a full ACK
SKB, that is.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This really just reformats the statement, but makes it
more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In ssb_calc_clock_rate(), there is a potential issue where the value of
m1 could be zero due to initialization using clkfactor_f6_resolv(). This
situation raised concerns about the possibility of a division by zero
error.

We fixed it by following the suggestions provided by Larry Finger
<Larry.Finger@lwfinger.net> and Michael Büsch <m@bues.ch>. The fix
involves returning a value of 1 instead of 0 in clkfactor_f6_resolv().
This modification ensures the proper functioning of the code and
eliminates the risk of division by zero errors.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230904232346.34991-1-rand.sec96@gmail.com

Secure firmware is protected by public/private key cryptography. To help
firmware self verify integrity, configure a heap address for these
data before downloading firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-9-pkshih@realtek.com

To support download more than one firmware, adjust flow to download
firmware by unit of firmware suit. Then, flow becomes

 1. initial setup - disable/enable_wcpu
 2. for all firmware suits
 2.1. download WiFi CPU, and check ready
 2.2. download BB MCU, and check ready
 3. check status code to make sure all ready
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-8-pkshih@realtek.com

Before downloading firmware for BB MCU, call this ops to enable baseband
hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-7-pkshih@realtek.com

Though WiFi 7 chips need BB MCU firmware, we don't download it in probe
stage. Instead, only bring interface up under normal operation or WoWLAN
mode. So, add an argument to assist download flow to setup download
settings properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-6-pkshih@realtek.com

For WiFi 6 chips, there is only single one firmware i.e. WiFi CPU firmware,
so no need an argument to discriminate them. For WiFi 7 chips, BB MCU
firmware is introduced, and we need to check it ready after downloading.

For each type of firmware, we need to check corresponding hardware ready
bit. After downloading all firmware, check status code to determine if
all things are ready.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-5-pkshih@realtek.com

To work with generalized flow of download firmware, implement WiFi 7
specific functions to support it. These functions include disable/enable
WiFi CPU, status of path ready, and status of firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-4-pkshih@realtek.com

In order to reuse the flow to download firmware, define some mac_gen::ops
to implement them for WiFi 6 and 7 chips individually. This doesn't change
logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-3-pkshih@realtek.com

To download firmware, we need to check path is ready. There are two kinds
of path -- one is to download firmware header, and the other is to download
firmware body.

Since the polling method is different from WiFi 7 chips, make it to be
an individual function, and then we can reuse the download flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230901073956.54203-2-pkshih@realtek.com

According to Wi-Fi/BT roles' settings, we fill corresponding H2Cs (host
to chip packets). Then, following MCC (multi-channel concurrency) pattern,
we send these H2Cs as planned. Eventually, the trigger H2Cs will be sent
to tell FW to really start/stop MCC.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230831053133.24015-7-pkshih@realtek.com