- 03 Feb, 2022 12 commits
-
-
Bo Jiao authored
Adjust proper eeprom size and add default calibrated data support for mt7916. Co-developed-by:
Shayne Chen <shayne.chen@mediatek.com> Signed-off-by:
Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by:
Bo Jiao <Bo.Jiao@mediatek.com> Reviewed-by:
Ryder Lee <ryder.lee@mediatek.com> Signed-off-by:
Felix Fietkau <nbd@nbd.name>
-
Bo Jiao authored
Update v2 offset. This is an intermediate patch to add mt7916 support. Co-developed-by:
-
Bo Jiao authored
mt7916 reports rx rate from rxd group3 directly. Co-developed-by:
-
Bo Jiao authored
Update txfree v3 format. This is an intermediate patch to add mt7916 support. Co-developed-by:
-
Bo Jiao authored
The mt7916 can support up to 544 wcid entries. This is an intermediate patch to add mt7916 support. Co-developed-by:
-
Bo Jiao authored
This is an intermediate patch to add mt7916 support. Co-developed-by:
-
Bo Jiao authored
Update firmware initialization for mt7916. This is an intermediate patch to add mt7916 support. Co-developed-by:
-
Bo Jiao authored
The RXQ of mt7916 are separated to MT_RXQ_MAIN_WA and MT_RXQ_MCU_WA, so, add initialization and preftech setting for the queue MT_RXQ_MAIN_WA. This is an intermediate patch to add mt7916 support. Co-developed-by:
-
Bo Jiao authored
mt7916 add MT_RXQ_MAIN_WA to receive tx free event separately This is an intermediate patch to add mt7916 support. Co-developed-by:
-
Bo Jiao authored
Add mt7915_reg_desc to differentiate chip generations. This is an intermediate patch to introduce mt7916 support. Co-developed-by:
-
Bo Jiao authored
Add mt7915_mmio_probe() which will be used for the upcoming devices. This is an intermediate patch to add mt7916 support. Co-developed-by:
-
Felix Fietkau authored
Check the register status bit instead of the trigger bit Signed-off-by:
-
- 01 Feb, 2022 11 commits
-
-
Hector Martin authored
This allows us to get console messages if the firmware crashed during early init, or if an operation failed and we're about to shut down. Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Hector Martin <marcan@marcan.st> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220131160713.245637-10-marcan@marcan.st
-
Hector Martin authored
Make all the iovar name arguments const char * instead of just char *. Reviewed-by:
-
Hector Martin authored
This was missing a NULL check, and we can collapse the strlen/alloc/copy into a devm_kstrdup(). Reviewed-by:
-
Hector Martin authored
The driver was enabling IRQs before the message processing was initialized. This could cause IRQs to come in too early and crash the driver. Instead, move the IRQ enable and hostready to a bus preinit function, at which point everything is properly initialized. Fixes: 9e37f045 ("brcmfmac: Adding PCIe bus layer support.") Reviewed-by:
-
Hector Martin authored
The alignment check was wrong (e.g. & 4 instead of & 3), and the logic was also inefficient if the length was not a multiple of 4, since it would needlessly fall back to copying the entire buffer bytewise. We already have a perfectly good memcpy_toio function, so just call that instead of rolling our own copy logic here. brcmf_pcie_init_ringbuffers was already using it anyway. Fixes: 9e37f045 ("brcmfmac: Adding PCIe bus layer support.") Reviewed-by:
-
Hector Martin authored
Move one of the declarations from sdio.c to pcie.c, since it makes no sense in the former (SDIO support is optional), and add missing ones. Fixes: 75729e11 ("brcmfmac: expose firmware config files through modinfo") Reviewed-by:
-
Hector Martin authored
If boardrev is missing from the NVRAM we add a default one, but this might need more space in the output buffer than was allocated. Ensure we have enough padding for this in the buffer. Fixes: 46f2b38a ("brcmfmac: insert default boardrev in nvram data if missing") Reviewed-by:
-
Hector Martin authored
This avoids leaking memory if brcmf_chip_get_raminfo fails. Note that the CLM blob is released in the device remove path. Fixes: 82f93cf4 ("brcmfmac: get chip's default RAM info during PCIe setup") Reviewed-by:
-
Colin Ian King authored
Variable ul_encalgo is initialized with a value that is never read, it is being re-assigned a new value in every case in the following switch statement. The initialization is redundant and can be removed. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Acked-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Yang Guang authored
The coccinelle report ./include/linux/ssb/ssb_driver_gige.h:98:8-9: WARNING: return of 0/1 in function 'ssb_gige_must_flush_posted_writes' with return type bool Return statements in functions returning bool should use true/false instead of 1/0. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Yang Guang <yang.guang5@zte.com.cn> Signed-off-by:
David Yang <davidcomponentone@gmail.com> Signed-off-by:
-
Jiasheng Jiang authored
As the possible failure of the ioremap(), the 'local->sram' and other two could be NULL. Therefore it should be better to check it in order to avoid the later dev_dbg. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by:
-
- 31 Jan, 2022 6 commits
-
-
Colin Ian King authored
Don't populate the read-only array queue_id_to_wmm_aci on the stack but instead make it static. Also makes the object code a little smaller. Signed-off-by:
-
Changcheng Deng authored
Use min_t() in order to make code cleaner. Reported-by:
Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by:
-
Ping-Ke Shih authored
Ping-Ke Shih answered[1] a question for a user about an rtl8821ce device that reported RFE 6, which the driver did not support. Ping-Ke suggested a possible fix, but the user never reported back. A second user discovered the above thread and tested the proposed fix. Accordingly, I am pushing this change, even though I am not the author. [1] https://lore.kernel.org/linux-wireless/3f5e2f6eac344316b5dd518ebfea2f95@realtek.com/Signed-off-by:
masterzorag <masterzorag@gmail.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Po-Hao Huang authored
Previously we allocated less memory than actual required, overwrite to the buffer causes the mm module to complaint and raise access violation faults. Along with potential memory leaks when returned early. Fix these by passing the correct size and proper deinit flow. Fixes: 10d162b2 ("rtw88: 8822c: add ieee80211_ops::hw_scan") Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Po-Hao Huang authored
Upon hw scan completion, idle mode is not re-entered. This might increase power consumption under no link mode. Fix this by adding the re-enter flow. We need another work for this since enter_ips waits for c2h_work to finish, which might lead to deadlock if caller is in the same work. Fixes: 10d162b2 ("rtw88: 8822c: add ieee80211_ops::hw_scan") Signed-off-by:
-
Muhammad Usama Anjum authored
ieee80211_probereq_get() can return NULL. Pointer skb should be checked for validty before use. If it is not valid, list of skbs needs to be freed. Fixes: 10d162b2 ("rtw88: 8822c: add ieee80211_ops::hw_scan") Signed-off-by:
Muhammad Usama Anjum <usama.anjum@collabora.com> Signed-off-by:
-
- 28 Jan, 2022 11 commits
-
-
Soontak Lee authored
CYW43570 is a 3-antenna, 2x2 MIMO,802.11a/b/g/n/ac, PCIe 3.0 for WLAN. It is BT/WIFI combo. Signed-off-by:
Soontak Lee <soontak.lee@cypress.com> Signed-off-by:
Chi-Hsien Lin <chi-hsien.lin@infineon.com> Signed-off-by:
Ian Lin <ian.lin-ee@infineon.com> Signed-off-by:
-
Hans de Goede authored
This is a second attempt at honering the country code send out by access points. This was first added in commit b0b524f0 ("brcmfmac: use ISO3166 country code and 0 rev as fallback"). Subsequently this was reverted in commit 151a7c12 ("Revert "brcmfmac: use ISO3166 country code and 0 rev as fallback""), because it was causing issues with AP mode on some brcmfmac models (specifically on BCM4359/9). Many devices ship with a nvram ccode value of X2/XT/XU/XV/ALL which are all special world-wide compatibility ccode-s. Most of these world-wide ccode-s allow passive scan mode only for 2.4GHz channels 12-14, only enabling them when an AP is seen on them. But at least on brcmfmac43455 devices this is not working correctly, these do not see accesspoints on channels 12-14 unless the ccode is changes to a country where these channels are allowed. Translating received country codes to an ISO3166 country code and 0 rev ccreq fixes devices using a brcmfmac43455 with a X2/XT/XU/XV/ALL ccode not seeing accesspoints on channels 12-14. To avoid this causing issues on other brcmfmac models again, the fallback is limited to only brcmfmac4345* chips this time. Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Soeren Moch <smoch@web.de> Cc: Fabio Aiuto <fabioaiuto83@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Tested-by: Soeren Moch <smoch@web.de> # on BCM4359/9 Signed-off-by:
-
Chin-Yen Lee authored
In the past we use dbi function of wifi mac to read/write pci config space, but the function will be remove in new chip. So use kernel api pci_read/write_config_byte instead. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
-
Johnson Lin authored
DIG, which is short for dynamic initial gain, is used to adjust gain to get good RX performance. CCK PD feature, a mechanism that adjusts 802.11b CCK packet detection(PD) power threshold based on environment noisy level in order to avoid false alarm. Also, refine related variable naming. Signed-off-by:
Johnson Lin <johnson.lin@realtek.com> Signed-off-by:
-
Íñigo Huguet authored
Call to dle_dfi_qempty might fail, leaving qempty.qempty untouched, which is latter used to control the for loop. If that happens, it's not initialized anywhere. Initialize it so the loop doesn't iterate unless it's modified by the call to dle_dfi_qempty. Signed-off-by:
Íñigo Huguet <ihuguet@redhat.com> Acked-by:
-
Zong-Zhe Yang authored
Make stuffs related to channel be collected in channel_params, and encapsulate the corresponding decision in get_channel_params(). Then, functions that takes channel_params can also notice subband type. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Zong-Zhe Yang authored
For next chipset which can support 6G band, we add the handling of ieee80211_supported_band for 6G band in advance. And a bitmap, support_bands, is added to rtw89_chip_info to declare which NL80211_BAND_* are supported. With the chipset's declaration, we register the corresponding instances of ieee80211_supported_band with wiphy. Signed-off-by:
-
Ping-Ke Shih authored
Each stations connected to AP needs to set an address CAM, so don't combine address and BSSID CAM. Signed-off-by:
-
Ping-Ke Shih authored
One mac_id is corresponding to one connected station, and port ID is a ID of virtual interfaces. With proper mac_id and port ID, firmware and hardware can handle a packet with correct context. Signed-off-by:
-
Ping-Ke Shih authored
If a packet we are going to send is broadcast/multicast and certain STAs are in sleep mode, a flag IEEE80211_TX_CTL_SEND_AFTER_DTIM is added to txinfo. Then, this kind of packets must be sent via HIQ instead of regular AC queues, because they should be sent right after beacon. Signed-off-by:
-
Ping-Ke Shih authored
HIQ is short for high queue that is used to send broadcast/multicast packets right after TBTT in AP mode. Two registers, DTIM and window size, are configured accordingly. Signed-off-by:
-
