- 30 Jun, 2020 6 commits
-
-
Jon Hunter authored
[ Upstream commit d8207c15 ] If probing the LP885x backlight fails after the regulators have been enabled, then the following warning is seen when releasing the regulators ... WARNING: CPU: 1 PID: 289 at drivers/regulator/core.c:2051 _regulator_put.part.28+0x158/0x160 Modules linked in: tegra_xudc lp855x_bl(+) host1x pwm_tegra ip_tables x_tables ipv6 nf_defrag_ipv6 CPU: 1 PID: 289 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200224 #1 Hardware name: NVIDIA Jetson TX1 Developer Kit (DT) ... Call trace: _regulator_put.part.28+0x158/0x160 regulator_put+0x34/0x50 devm_regulator_release+0x10/0x18 release_nodes+0x12c/0x230 devres_release_all+0x34/0x50 really_probe+0x1c0/0x370 driver_probe_device+0x58/0x100 device_driver_attach+0x6c/0x78 __driver_attach+0xb0/0xf0 bus_for_each_dev+0x68/0xc8 driver_attach+0x20/0x28 bus_add_driver+0x160/0x1f0 driver_register+0x60/0x110 i2c_register_driver+0x40/0x80 lp855x_driver_init+0x20/0x1000 [lp855x_bl] do_one_initcall+0x58/0x1a0 do_init_module+0x54/0x1d0 load_module+0x1d80/0x21c8 __do_sys_finit_module+0xe8/0x100 __arm64_sys_finit_module+0x18/0x20 el0_svc_common.constprop.3+0xb0/0x168 do_el0_svc+0x20/0x98 el0_sync_handler+0xf4/0x1b0 el0_sync+0x140/0x180 Fix this by ensuring that the regulators are disabled, if enabled, on probe failure. Finally, ensure that the vddio regulator is disabled in the driver remove handler. Signed-off-by:
Jon Hunter <jonathanh@nvidia.com> Reviewed-by:
Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Bryan O'Donoghue authored
[ Upstream commit f47ab3c2 ] During the process of debugging a processor derived from the msm8916 which we found the new processor was not starting one of its PLLs. After tracing the addresses and writes that downstream was doing and comparing to upstream it became obvious that we were writing to a different register location than downstream when trying to configure the PLL. This error is also present in upstream msm8916. As an example clk-pll.c::clk_pll_recalc_rate wants to write to pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an example lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf 0x01823010 GCC_BIMC_PLL_USER_CTL 0x01823014 GCC_BIMC_PLL_CONFIG_CTL This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll. This error is likely not apparent since the bootloader will already have initialized these PLLs. This patch corrects the location of config_reg from PLL_CONFIG_CTL to PLL_USER_CTL for all relevant PLLs on msm8916. Fixes commit 3966fab8 ("clk: qcom: Add MSM8916 Global Clock Controller support") Cc: Georgi Djakov <georgi.djakov@linaro.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@kernel.org> Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.orgSigned-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Andy Shevchenko authored
[ Upstream commit 97b31a6f ] With DEBUG_SHIRQ enabled we have a kernel crash [ 116.482696] BUG: kernel NULL pointer dereference, address: 0000000000000000 ... [ 116.606571] Call Trace: [ 116.609023] <IRQ> [ 116.611047] complete+0x34/0x50 [ 116.614206] bmp085_eoc_irq+0x9/0x10 [bmp280] because DEBUG_SHIRQ mechanism fires an IRQ before registration and drivers ought to be able to handle an interrupt happening before request_irq() returns. Fixes: aae95394 ("iio: pressure: bmp280: add support for BMP085 EOC interrupt") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Adam Honse authored
[ Upstream commit f27237c1 ] The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper equivalents have a secondary SMBus controller at I/O port address 0x0B20. This bus is used by several manufacturers to control motherboard RGB lighting via embedded controllers. I have been using this bus in my OpenRGB project to control the Aura RGB on many motherboards and ASRock also uses this bus for their Polychrome RGB controller. I am not aware of any CZ-compatible platforms which do not have the second SMBus channel. All of AMD's AM4- and Threadripper- series chipsets that OpenRGB users have tested appear to have this secondary bus. I also noticed this secondary bus is present on older AMD platforms including my FM1 home server. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587Signed-off-by:
Adam Honse <calcprogrammer1@gmail.com> Reviewed-by:
Jean Delvare <jdelvare@suse.de> Reviewed-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Rikard Falkeborn authored
[ Upstream commit ee25d974 ] round_down() can only round to powers of 2. If round_down() is asked to round to something that is not a power of 2, incorrect results are produced. The incorrect results can be both too large and too small. Instead, use rounddown() which can round to any number. Fixes: 6a721db1 ("clk: sunxi: Add A31 clocks support") Signed-off-by:
Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Signed-off-by:
-
Enric Balletbo i Serra authored
[ Upstream commit 87c3d579 ] regmap is a library function that gets selected by drivers that need it. No driver modules should depend on it. Depending on REGMAP_I2C makes this driver only build if another driver already selected REGMAP_I2C, as the symbol can't be selected through the menu kernel configuration. Fixes: 2219a935 ("power_supply: Add TI BQ24257 charger driver") Signed-off-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by:
-
- 20 Jun, 2020 34 commits
-
-
Greg Kroah-Hartman authored
-
Adrian Hunter authored
commit 85afd355 upstream. Reportedly, from 19.10 Ubuntu has begun mixing up the location of some debug symbol files, putting files expected to be in /usr/lib/debug/usr/lib into /usr/lib/debug/lib instead. Fix by adding another dso_binary_type. Example on Ubuntu 20.04 Before: $ perf record -e intel_pt//u uname Linux [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.030 MB perf.data ] $ perf script --call-trace | head -5 uname 14003 [005] 15321.764958566: cbr: 42 freq: 4219 MHz (156%) uname 14003 [005] 15321.764958566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4100 uname 14003 [005] 15321.764961566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4df0 uname 14003 [005] 15321.764961900: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4e18 uname 14003 [005] 15321.764963233: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc5128 After: $ perf script --call-trace | head -5 uname 14003 [005] 15321.764958566: cbr: 42 freq: 4219 MHz (156%) uname 14003 [005] 15321.764958566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _start uname 14003 [005] 15321.764961566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start uname 14003 [005] 15321.764961900: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start uname 14003 [005] 15321.764963233: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start Reported-by:
Travis Downs <travis.downs@gmail.com> Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/20200526155207.9172-1-adrian.hunter@intel.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Masami Hiramatsu authored
commit f41ebe9d upstream. When a probe point is expanded to several places (like inlined) and if some of them are skipped because of blacklisted or __init function, those trace_events has no event name. It must be skipped while showing results. Without this fix, you can see "(null):(null)" on the list, # ./perf probe request_resource reserve_setup is out of .text, skip it. Added new events: (null):(null) (on request_resource) probe:request_resource (on request_resource) You can now use it in all perf tools, such as: perf record -e probe:request_resource -aR sleep 1 # With this fix, it is ignored: # ./perf probe request_resource reserve_setup is out of .text, skip it. Added new events: probe:request_resource (on request_resource) You can now use it in all perf tools, such as: perf record -e probe:request_resource -aR sleep 1 # Fixes: 5a51fcd1 ("perf probe: Skip kernel symbols which is out of .text") Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Tested-by:
-
H. Nikolaus Schaller authored
commit 5e02f3b3 upstream. Otherwise it will corrupt the console log during debugging. Fixes: 7b5362a6 ("w1: omap_hdq: Fix some error/debug handling.") Cc: stable@vger.kernel.org Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
H. Nikolaus Schaller <hns@goldelico.com> Link: https://lore.kernel.org/r/cd0d55749a091214106575f6e1d363c6db56622f.1590255176.git.hns@goldelico.comSigned-off-by:
-
Miquel Raynal authored
commit f5146690 upstream. nand_cleanup() is supposed to be called on error after a successful call to nand_scan() to free all NAND resources. There is no real Fixes tag applying here as the use of nand_release() in this driver predates by far the introduction of nand_cleanup() in commit d44154f9 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources") which makes this change possible, hence pointing it as the commit to fix for backporting purposes, even if this commit is not introducing any bug. Fixes: d44154f9 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources") Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-41-miquel.raynal@bootlin.comSigned-off-by:
-
Álvaro Fernández Rojas authored
commit 130bbde4 upstream. First 2 bytes are used in large-page nand. Fixes: ef5eeea6 ("mtd: nand: brcm: switch to mtd_ooblayout_ops") Cc: stable@vger.kernel.org Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by:
-
NeilBrown authored
commit 24c5efe4 upstream. gss_mech_register() calls svcauth_gss_register_pseudoflavor() for each flavour, but gss_mech_unregister() does not call auth_domain_put(). This is unbalanced and makes it impossible to reload the module. Change svcauth_gss_register_pseudoflavor() to return the registered auth_domain, and save it for later release. Cc: stable@vger.kernel.org (v2.6.12+) Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
NeilBrown authored
commit d47a5dc2 upstream. There is no valid case for supporting duplicate pseudoflavor registrations. Currently the silent acceptance of such registrations is hiding a bug. The rpcsec_gss_krb5 module registers 2 flavours but does not unregister them, so if you load, unload, reload the module, it will happily continue to use the old registration which now has pointers to the memory were the module was originally loaded. This could lead to unexpected results. So disallow duplicate registrations. Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651 Cc: stable@vger.kernel.org (v2.6.12+) Signed-off-by:
-
Masahiro Yamada authored
commit 4b50c8c4 upstream. This code does not work as stated in the comment. $(CONFIG_MODVERSIONS) is always empty because it is expanded before include/config/auto.conf is included. Hence, 'make modules' with CONFIG_MODVERSION=y cannot record the version CRCs. This has been broken since 2003, commit ("kbuild: Enable modules to be build using the "make dir/" syntax"). [1] [1]: https://git.kernel.org/pub/scm/linux/kernel/git/history/history.git/commit/?id=15c6240cdc44bbeef3c4797ec860f9765ef4f1a7 Cc: linux-stable <stable@vger.kernel.org> # v2.5.71+ Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
Michael Ellerman authored
commit 93900337 upstream. create_cpu_loop() calls smu_sat_get_sdb_partition() which does kmalloc() and returns the allocated buffer. In fact it's called twice, and neither buffer is freed. This results in a memory leak as reported by Erhard: unreferenced object 0xc00000047081f840 (size 32): comm "kwindfarm", pid 203, jiffies 4294880630 (age 5552.877s) hex dump (first 32 bytes): c8 06 02 7f ff 02 ff 01 fb bf 00 41 00 20 00 00 ...........A. .. 00 07 89 37 00 a0 00 00 00 00 00 00 00 00 00 00 ...7............ backtrace: [<0000000083f0a65c>] .smu_sat_get_sdb_partition+0xc4/0x2d0 [windfarm_smu_sat] [<000000003010fcb7>] .pm112_wf_notify+0x104c/0x13bc [windfarm_pm112] [<00000000b958b2dd>] .notifier_call_chain+0xa8/0x180 [<0000000070490868>] .blocking_notifier_call_chain+0x64/0x90 [<00000000131d8149>] .wf_thread_func+0x114/0x1a0 [<000000000d54838d>] .kthread+0x13c/0x190 [<00000000669b72bc>] .ret_from_kernel_thread+0x58/0x64 unreferenced object 0xc0000004737089f0 (size 16): comm "kwindfarm", pid 203, jiffies 4294880879 (age 5552.050s) hex dump (first 16 bytes): c4 04 01 7f 22 11 e0 e6 ff 55 7b 12 ec 11 00 00 ...."....U{..... backtrace: [<0000000083f0a65c>] .smu_sat_get_sdb_partition+0xc4/0x2d0 [windfarm_smu_sat] [<00000000b94ef7e1>] .pm112_wf_notify+0x1294/0x13bc [windfarm_pm112] [<00000000b958b2dd>] .notifier_call_chain+0xa8/0x180 [<0000000070490868>] .blocking_notifier_call_chain+0x64/0x90 [<00000000131d8149>] .wf_thread_func+0x114/0x1a0 [<000000000d54838d>] .kthread+0x13c/0x190 [<00000000669b72bc>] .ret_from_kernel_thread+0x58/0x64 Fix it by rearranging the logic so we deal with each buffer separately, which then makes it easy to free the buffer once we're done with it. Fixes: ac171c46 ("[PATCH] powerpc: Thermal control for dual core G5s") Cc: stable@vger.kernel.org # v2.6.16+ Reported-by:
Erhard F. <erhard_f@mailbox.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Tested-by:
-
Dmitry Osipenko authored
commit 35509737 upstream. The PL310 Auxiliary Control Register shouldn't have the "Full line of zero" optimization bit being set before L2 cache is enabled. The L2X0 driver takes care of enabling the optimization by itself. This patch fixes a noisy error message on Tegra20 and Tegra30 telling that cache optimization is erroneously enabled without enabling it for the CPU: L2C-310: enabling full line of zeros but not enabled in Cortex-A9 Cc: <stable@vger.kernel.org> Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Tested-by:
Nicolas Chauvet <kwizart@gmail.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Douglas Anderson authored
commit b5945214 upstream. cpu_pm_notify() is basically a wrapper of notifier_call_chain(). notifier_call_chain() doesn't initialize *nr_calls to 0 before it starts incrementing it--presumably it's up to the callers to do this. Unfortunately the callers of cpu_pm_notify() don't init *nr_calls. This potentially means you could get too many or two few calls to CPU_PM_ENTER_FAILED or CPU_CLUSTER_PM_ENTER_FAILED depending on the luck of the stack. Let's fix this. Fixes: ab10023e ("cpu_pm: Add cpu power management notifiers") Cc: stable@vger.kernel.org Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200504104917.v6.3.I2d44fc0053d019f239527a4e5829416714b7e299@changeidSigned-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Al Viro authored
commit 142cd252 upstream. We do need access_process_vm() to access the target's reg_window. However, access to caller's memory (storing the result in genregs32_get(), fetching the new values in case of genregs32_set()) should be done by normal uaccess primitives. Fixes: ad4f9576 ([SPARC64]: Fix user accesses in regset code.) Cc: stable@kernel.org Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit cf51e129 upstream. It needs access_process_vm() if the traced process does not share mm with the caller. Solution is similar to what sparc64 does. Note that genregs32_set() is only ever called with pos being 0 or 32 * sizeof(u32) (the latter - as part of PTRACE_SETREGS handling). Cc: stable@kernel.org Signed-off-by:
-
Jonathan Bakker authored
commit f354157a upstream. Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers are saved and restored over a suspend/resume cycle. However, the EINT_MASK registers are not. On S5PV210 at the very least, these registers are not retained over suspend, leading to the interrupts remaining masked upon resume and therefore no interrupts being triggered for the device. There should be no effect on any SoCs that do retain these registers as theoretically we would just be re-writing what was already there. Fixes: 7ccbc60c ("pinctrl: exynos: Handle suspend/resume of GPIO EINT registers") Cc: <stable@vger.kernel.org> Signed-off-by:
Jonathan Bakker <xc-racer2@live.ca> Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Anders Roxell authored
commit 73174acc upstream. Make sure that the POWER_RESET_VEXPRESS driver won't have bind/unbind attributes available via the sysfs, so lets be explicit here and use ".suppress_bind_attrs = true" to prevent userspace from doing something silly. Link: https://lore.kernel.org/r/20200527112608.3886105-2-anders.roxell@linaro.org Cc: stable@vger.kernel.org Signed-off-by:
Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Kai-Heng Feng authored
commit 165ae7a8 upstream. igb device gets runtime suspended when there's no link partner. We can't get correct speed under that state: $ cat /sys/class/net/enp3s0/speed 1000 In addition to that, an error can also be spotted in dmesg: [ 385.991957] igb 0000:03:00.0 enp3s0: PCIe link lost Since device can only be runtime suspended when there's no link partner, we can skip reading register and let the following logic set speed and duplex with correct status. The more generic approach will be wrap get_link_ksettings() with begin() and complete() callbacks. However, for this particular issue, begin() calls igb_runtime_resume() , which tries to rtnl_lock() while the lock is already hold by upper ethtool layer. So let's take this approach until the igb_runtime_resume() no longer needs to hold rtnl_lock. CC: stable <stable@vger.kernel.org> Suggested-by:
Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Larry Finger authored
commit 6a29d134 upstream. Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43legacy did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43legacy will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.netSigned-off-by:
-
Larry Finger authored
commit 75d057bd upstream. Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43 did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43 will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Reported-and-tested-by:
Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by:
-
Larry Finger authored
commit ec4d3e3a upstream. This patch fixes commit 75388acd ("add mac80211-based driver for legacy BCM43xx devices") In https://bugzilla.kernel.org/show_bug.cgi?id=207093, a defect in b43legacy is reported. Upon testing, thus problem exists on PPC and X86 platforms, is present in the oldest kernel tested (3.2), and has been present in the driver since it was first added to the kernel. The problem is a corrupted channel status received from the device. Both the internal card in a PowerBook G4 and the PCMCIA version (Broadcom BCM4306 with PCI ID 14e4:4320) have the problem. Only Rev, 2 (revision 4 of the 802.11 core) of the chip has been tested. No other devices using b43legacy are available for testing. Various sources of the problem were considered. Buffer overrun and other sources of corruption within the driver were rejected because the faulty channel status is always the same, not a random value. It was concluded that the faulty data is coming from the device, probably due to a firmware bug. As that source is not available, the driver must take appropriate action to recover. At present, the driver reports the error, and them continues to process the bad packet. This is believed that to be a mistake, and the correct action is to drop the correpted packet. Fixes: 75388acd ("add mac80211-based driver for legacy BCM43xx devices") Cc: Stable <stable@vger.kernel.org> Signed-off-by:
-
Chuhong Yuan authored
commit 9453264e upstream. go7007_snd_init() misses a snd_card_free() in an error path. Add the missed call to fix it. Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> [Salvatore Bonaccorso: Adjust context for backport to versions which do not contain c0decac1 ("media: use strscpy() instead of strlcpy()") and ba78170e ("media: go7007: Fix misuse of strscpy")] Signed-off-by:
Salvatore Bonaccorso <carnil@debian.org> Signed-off-by:
-
Christian Lamparter authored
commit b14fba7e upstream. This patch follows up on a bug-report by Frank Schäfer that discovered P2P GO wasn't working with wpa_supplicant. This patch removes part of the broken P2P GO support but keeps the vif switchover code in place. Cc: <stable@vger.kernel.org> Link: <https://lkml.kernel.org/r/3a9d86b6-744f-e670-8792-9167257edef8@googlemail.com> Reported-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Punit Agrawal authored
commit d601afca upstream. It's an error if the value of the RX/TX tail descriptor does not match what was written. The error condition is true regardless the duration of the interference from ME. But the driver only performs the reset if E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have transpired. The extra condition can lead to inconsistency between the state of hardware as expected by the driver. Fix this by dropping the check for number of delay iterations. While at it, also make __ew32_prepare() static as it's not used anywhere else. CC: stable <stable@vger.kernel.org> Signed-off-by:
Punit Agrawal <punit1.agrawal@toshiba.co.jp> Reviewed-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Tested-by:
-
Ashok Raj authored
commit aa0ce96d upstream. Root Complex Integrated Endpoints (RCiEPs) do not have an upstream bridge, so pci_configure_mps() previously ignored them, which may result in reduced performance. Instead, program the Max_Payload_Size of RCiEPs to the maximum supported value (unless it is limited for the PCIE_BUS_PEER2PEER case). This also affects the subsequent programming of Max_Read_Request_Size because Linux programs MRRS based on the MPS value. Fixes: 9dae3a97 ("PCI: Move MPS configuration check to pci_configure_device()") Link: https://lore.kernel.org/r/1585343775-4019-1-git-send-email-ashok.raj@intel.comTested-by:
Dave Jiang <dave.jiang@intel.com> Signed-off-by:
Ashok Raj <ashok.raj@intel.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Giuliano Procida authored
This fixes the 4.9 backport commit f530afb9 which was upstream commit f5bbbbe4. The upstream commit added a call to synchronize_rcu to _blk_mq_update_nr_hw_queues, just after freezing queues. In the backport this landed (in blk_mq_update_nr_hw_queues instead), just after unfreezeing queues. This commit moves the call to its intended place. Fixes: f530afb9 ("blk-mq: sync the update nr_hw_queues with blk_mq_queue_tag_busy_iter") Signed-off-by:
Giuliano Procida <gprocida@google.com> Signed-off-by:
-
Omar Sandoval authored
[ Upstream commit 6d3113a1 ] In btrfs_submit_direct_hook(), if a direct I/O write doesn't span a RAID stripe or chunk, we submit orig_bio without cloning it. In this case, we don't increment pending_bios. Then, if btrfs_submit_dio_bio() fails, we decrement pending_bios to -1, and we never complete orig_bio. Fix it by initializing pending_bios to 1 instead of incrementing later. Fixing this exposes another bug: we put orig_bio prematurely and then put it again from end_io. Fix it by not putting orig_bio. After this change, pending_bios is really more of a reference count, but I'll leave that cleanup separate to keep the fix small. Fixes: e65e1535 ("btrfs: fix panic caused by direct IO") CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Nikolay Borisov <nborisov@suse.com> Reviewed-by:
Josef Bacik <josef@toxicpanda.com> Reviewed-by:
Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Eric Biggers authored
commit 08adf452 upstream. 'igrab(d_inode(dentry->d_parent))' without holding dentry->d_lock is broken because without d_lock, d_parent can be concurrently changed due to a rename(). Then if the old directory is immediately deleted, old d_parent->inode can be NULL. That causes a NULL dereference in igrab(). To fix this, use dget_parent() to safely grab a reference to the parent dentry, which pins the inode. This also eliminates the need to use d_find_any_alias() other than for the initial inode, as we no longer throw away the dentry at each step. This is an extremely hard race to hit, but it is possible. Adding a udelay() in between the reads of ->d_parent and its ->d_inode makes it reproducible on a no-journal filesystem using the following program: #include <fcntl.h> #include <unistd.h> int main() { if (fork()) { for (;;) { mkdir("dir1", 0700); int fd = open("dir1/file", O_RDWR|O_CREAT|O_SYNC); write(fd, "X", 1); close(fd); } } else { mkdir("dir2", 0700); for (;;) { rename("dir1/file", "dir2/file"); rmdir("dir1"); } } } Fixes: d59729f4 ("ext4: fix races in ext4_sync_parent()") Cc: stable@vger.kernel.org Signed-off-by:
Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20200506183140.541194-1-ebiggers@kernel.orgSigned-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Harshad Shirwadkar authored
commit c36a71b4 upstream. If eh->eh_max is 0, EXT_MAX_EXTENT/INDEX would evaluate to unsigned (-1) resulting in illegal memory accesses. Although there is no consistent repro, we see that generic/019 sometimes crashes because of this bug. Ran gce-xfstests smoke and verified that there were no regressions. Signed-off-by:
Harshad Shirwadkar <harshadshirwadkar@gmail.com> Link: https://lore.kernel.org/r/20200421023959.20879-2-harshadshirwadkar@gmail.comSigned-off-by:
-
Roberto Sassu authored
commit 0c4395fb upstream. Don't immediately return if the signature is portable and security.ima is not present. Just set error so that memory allocated is freed before returning from evm_calc_hmac_or_hash(). Fixes: 50b97748 ("EVM: Add support for portable signature format") Signed-off-by:
Roberto Sassu <roberto.sassu@huawei.com> Cc: stable@vger.kernel.org Signed-off-by:
Mimi Zohar <zohar@linux.ibm.com> Signed-off-by:
-
Roberto Sassu authored
commit 067a436b upstream. This patch prevents the following oops: [ 10.771813] BUG: kernel NULL pointer dereference, address: 0000000000000 [...] [ 10.779790] RIP: 0010:ima_match_policy+0xf7/0xb80 [...] [ 10.798576] Call Trace: [ 10.798993] ? ima_lsm_policy_change+0x2b0/0x2b0 [ 10.799753] ? inode_init_owner+0x1a0/0x1a0 [ 10.800484] ? _raw_spin_lock+0x7a/0xd0 [ 10.801592] ima_must_appraise.part.0+0xb6/0xf0 [ 10.802313] ? ima_fix_xattr.isra.0+0xd0/0xd0 [ 10.803167] ima_must_appraise+0x4f/0x70 [ 10.804004] ima_post_path_mknod+0x2e/0x80 [ 10.804800] do_mknodat+0x396/0x3c0 It occurs when there is a failure during IMA initialization, and ima_init_policy() is not called. IMA hooks still call ima_match_policy() but ima_rules is NULL. This patch prevents the crash by directly assigning the ima_default_policy pointer to ima_rules when ima_rules is defined. This wouldn't alter the existing behavior, as ima_rules is always set at the end of ima_init_policy(). Cc: stable@vger.kernel.org # 3.7.x Fixes: 07f6a794 ("ima: add appraise action keywords and default rules") Reported-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Krzysztof Struczynski authored
commit 1129d31b upstream. Function hash_long() accepts unsigned long, while currently only one byte is passed from ima_hash_key(), which calculates a key for ima_htable. Given that hashing the digest does not give clear benefits compared to using the digest itself, remove hash_long() and return the modulus calculated on the first two bytes of the digest with the number of slots. Also reduce the depth of the hash table by doubling the number of slots. Cc: stable@vger.kernel.org Fixes: 3323eec9 ("integrity: IMA as an integrity service provider") Co-developed-by:
Krzysztof Struczynski <krzysztof.struczynski@huawei.com> Acked-by: David.Laight@aculab.com (big endian system concerns) Signed-off-by:
-
Andrea Arcangeli authored
commit c444eb56 upstream. Write protect anon page faults require an accurate mapcount to decide if to break the COW or not. This is implemented in the THP path with reuse_swap_page() -> page_trans_huge_map_swapcount()/page_trans_huge_mapcount(). If the COW triggers while the other processes sharing the page are under a huge pmd split, to do an accurate reading, we must ensure the mapcount isn't computed while it's being transferred from the head page to the tail pages. reuse_swap_cache() already runs serialized by the page lock, so it's enough to add the page lock around __split_huge_pmd_locked too, in order to add the missing serialization. Note: the commit in "Fixes" is just to facilitate the backporting, because the code before such commit didn't try to do an accurate THP mapcount calculation and it instead used the page_count() to decide if to COW or not. Both the page_count and the pin_count are THP-wide refcounts, so they're inaccurate if used in reuse_swap_page(). Reverting such commit (besides the unrelated fix to the local anon_vma assignment) would have also opened the window for memory corruption side effects to certain workloads as documented in such commit header. Signed-off-by:
Andrea Arcangeli <aarcange@redhat.com> Suggested-by:
Jann Horn <jannh@google.com> Reported-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Fixes: 6d0a07ed ("mm: thp: calculate the mapcount correctly for THP pages during WP faults") Cc: stable@vger.kernel.org Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Marcos Paulo de Souza authored
commit 89efda52 upstream. Whenever a chown is executed, all capabilities of the file being touched are lost. When doing incremental send with a file with capabilities, there is a situation where the capability can be lost on the receiving side. The sequence of actions bellow shows the problem: $ mount /dev/sda fs1 $ mount /dev/sdb fs2 $ touch fs1/foo.bar $ setcap cap_sys_nice+ep fs1/foo.bar $ btrfs subvolume snapshot -r fs1 fs1/snap_init $ btrfs send fs1/snap_init | btrfs receive fs2 $ chgrp adm fs1/foo.bar $ setcap cap_sys_nice+ep fs1/foo.bar $ btrfs subvolume snapshot -r fs1 fs1/snap_complete $ btrfs subvolume snapshot -r fs1 fs1/snap_incremental $ btrfs send fs1/snap_complete | btrfs receive fs2 $ btrfs send -p fs1/snap_init fs1/snap_incremental | btrfs receive fs2 At this point, only a chown was emitted by "btrfs send" since only the group was changed. This makes the cap_sys_nice capability to be dropped from fs2/snap_incremental/foo.bar To fix that, only emit capabilities after chown is emitted. The current code first checks for xattrs that are new/changed, emits them, and later emit the chown. Now, __process_new_xattr skips capabilities, letting only finish_inode_if_needed to emit them, if they exist, for the inode being processed. This behavior was being worked around in "btrfs receive" side by caching the capability and only applying it after chown. Now, xattrs are only emmited _after_ chown, making that workaround not needed anymore. Link: https://github.com/kdave/btrfs-progs/issues/202 CC: stable@vger.kernel.org # 4.4+ Suggested-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
Marcos Paulo de Souza <mpdesouza@suse.com> Signed-off-by:
-
Qiushi Wu authored
[ Upstream commit c343bf1b ] kobject_init_and_add() takes reference even when it fails. If this function returns an error, kobject_put() must be called to properly clean up the memory associated with the object. Previous commit "b8eb7183" fixed a similar problem. Signed-off-by:
Qiushi Wu <wu000273@umn.edu> [ rjw: Subject ] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
