The various variables tracking bmiss interrupts
are not really used anywhere except in a debug
message. Remove them since they have no functional
purpose.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch makes sure that valid WOW triggers
are present before trying to suspend the device.
Also, introduce and use ATH_OP_WOW_ENABLED to
bypass PCI suspend and clear it in resume().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Registering the card as a wakeup source needs to
be done once, during initialization. When the WOW
configuration changes, the card's status as wakeup
source needs to be changed too and this is done
via the set_wakeup() callback. Also, make sure
the device is removed properly using ath9k_deinit_wow().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If CONFIG_ATH9K_CHANNEL_CONTEXT is enabled, check whether
multiple contexts are active and if so, return 1 without
enabling WOW since we don't support it in this case.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If multiple interfaces are active or there is no
associated station interface, bail out early and
return 1 so that mac80211 can proceed with the normal
suspend routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WOW capability is registered with mac80211 only when
the device has the ability to wakeup, so there is no
need to check in the suspend() routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Do not try to cancel work instances and ANI when
the device is not present or WOW triggers are
not configured. Bail out early and use ath_err()
for such error conditions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Enabling WOW based on the chip is incorrect since
it needs to be done for specific sub-devices which
have proper platform support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When AP is started, firmware exits power save mode. This
means power save manager of AP takes priority over station.
Firmware stop sending periodic AWAKE events to host.

We may have UAPSD enabled on station which buffers data
packets until AWAKE event from firmware. Data path is
unnecessarily blocked in this case. This patch disables
UAPSD mode to reenable transmit data path.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch makes sure that skb is freed after downloading
NULL packet in error cases. Also, USB chipsets return
-EINPROGRESS after downloading packets, they are freed in
USB completion handler later. We will add missing change
to set tx_lock_flag for USB which blocks further packets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Memory is leaked after downloading already processed packet. This
patch fixes the problem by freeing returned skb. Other transmit
paths don't have this problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Wakeup timer is in sync with 'pm_wakeup_fw_try' flag. It
has been started instead of cancelling at one place. This
patch corrects it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There are instances where the DMA engine stalls. The new code detects
such stalls and restarts DMA without needing a power reset.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The firmware supplies two kinds of packets via the RX mechanism. Besides the
normal data received over the air, these packets may contain bluetooth status
and other information. The present code fails to detect which kind of
information was received.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Initially, the routine to update the write point in the FIFO buffer was
coded to save CPU time by not doing the calculation every interrupt. This
was an error and results in TX hangs.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When the buffer descriptor index exceeds 2, then a TX HANG condition
will result.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There are new (not anymore?) Broadcom 802.11ac wireless cards based on
chipsets like BCM4352 and BCM4360. They use a new PHY type (called
simply AC) that will require new specific code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

AC-PHY hardware includes new control 0x3 bits that need to be set to the
0x1 by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This is stil incomplete, so we don't add PCI IDs of new devices yet.
Purpose of this patch is to allow testing & adjusting rest of the code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There are some PCIe core fixes that need to be applied before accessing
SPROM, otherwise reading it may fail.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This allows us to drop some #ifdef magic (mess).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Extracting values from it is still unsupported, but at least we'll
display some meaningful error now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

These chipsets don't need changing clock mode.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

On some AR955x/QCA953x boards, noise floor calibration
gets stuck and the cause is a hardware/BB issue. To fix
this, peak detect calibration in the HW is disabled
and is done in the driver instead. There a few differences
with the calibration routine for older chips like
AR9331.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The value is different for PCOEM cards and AR955x/AR953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The LNA gain setting override needs to be done
only for AR9330 and PCOEM chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This can be used if we need to apply register settings
for all PCOEM solutions (in the AR9003 family).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch disables HW peak detect calibration for
AR955x, since it is problematic on a few boards.
Instead, manual calibration will be done in the
driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch disables HW peak detect calibration for
QCA953x, since it is problematic on a few boards.
Instead, manual calibration will be done in the
driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

b43 has a FIXME about locking in the mac80211 set-beacon-int callback for a long time.
As it turns out there actually is a tiny race window that could result in
a use-after-free bug of the 'current_beacon' memory.
Nobody ever reported this, so it probably never happened.

Fix this by adding a spin lock that protects the current_beacon access.
We must not be in atomic context while accessing hardware (due to SDIO),
so the beacon update bottom half has to clone the skb and release the lock
before writing it to hardware.

Let's all hope that this stops the troll who is trying to submit incorrect
fixes for this issue repeatedly.
And let's hope that I'm not a troll, too, who just hides even more evil code
in an even more complex attempt to fix the issue.
Signed-off-by: Michael Buesch <m@bues.ch>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch enables 11h extensions in FW upon detecting DFS
channel in start radar detection/channel switch handlers.
Patch also takes care of disabling 11h when non DFS channels
are to be set during start_ap handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds cfg80211 channel_switch support for mwifiex.
Upon receiving channel switch request, driver would parse channel
switch announcement IE from beacon_data.
If TX is blocked, netdev queues are stopped. IEs from csa_beacon
are then parsed and set to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for radar_detected event from FW.
Driver in turn would stop netdev queues to stop TX traffic and
issue RADAR_DETECT event to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for channel report enabling.
Channel report event happens if radar is detected on specified channel
after driver has issued radar detect command within CAC time.
Driver in turn sends RADAR_DETECTED event to cfg80211 to tell radar was
detected within CAC time.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for cfg80211 start_radar_detection handler.
Upon reception of start_radar_detection, driver prepares radar detect
command to FW.

Delayed work is queued for CAC time which sends radar detection finished
event to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Head & Tail IEs are supposed to be added to beacon and probe response.
This patch adds separate function for parsing head and tail IEs from
cfg80211_beacon_data and sets them to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Refactor mwifiex_cfg80211_start_ap by creating separate function
to set AP channel and another for configuring other AP parameters
and starting AP.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch moves IE management routine to end of start_ap handler.
IEs now would be updated after AP has started.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Store AP configuration in private structure so that we know
current AP configuration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>