Currently hwmod only provides the offset for the context lose
register, and if we attempt to share the same register between two or
more hwmods, the resulting context loss counts get wrong. Thus, we
need a way to specify which bits are used for the context loss
information for each.  This is accomplished by adding a new field to
the omap4 prcm struct, 'lostcontext_mask', which specifies a bit-mask
to use for filtering the register.

Mark the affected hwmods appropriately.  'l4_abe' hwmod uses the
LOSTMEM_AESSMEM bit of RM_ABE_AESS_CONTEXT register, as l4_abe doesn't
have its own dedicated register for this purpose. This register is
shared with 'aess' hwmod, thus both hwmods must also specify which
bits of the register are used for them.

This patch only adds the hwmod data, but a future patch should add
code support such that only the specified bits are read and cleared by
the context lose counter update code. If a hwmod doesn't specify
'lostcontext_mask' (default behavior), the whole contents of the
context register should be used without any filtering.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: updated to apply after conversion to use flag bit for
 missing module context-loss register; combined data and code patches;
 dropped code change due to serial driver breakage]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

On OMAP4, there is no support to read previous logic state
or previous memory state achieved when a power domain transitions
to RET. Instead there are module level context registers.

In order to support the powerdomain level logic/mem_off_counters
on OMAP4, instead use the previous power state achieved (RET) and
the *programmed* logic/mem RET state to derive if a powerdomain lost
logic or did not.

If the powerdomain is programmed to enter RET state and lose logic
in RET state, knowing that the powerdomain entered RET is good enough
to derive that the logic was lost as well, in such cases.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: removed dependency on functional power state series for now;
 bumped copyright date]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The decision was made a few months ago to allow struct omap_hwmod
records and struct clk records to omit clockdomain information if the
clockdomain is not software-controllable.  See for example commit
868c157d ("ARM: OMAP2+: hwmod: remove
prm_clkdm, cm_clkdm; allow hwmods to have no clockdomain").

So convert an existing pr_warning() to a pr_debug() (regarding missing
clockdomains in clocks), and add a pr_debug() for missing hwmod
clockdomains.  It's still useful to enable these messages for
debugging, since missing clockdomains can cause hard-to-debug problems
with power management; see for example commit
6c4a057b ("ARM: OMAP4: clock data:
Force a DPLL clkdm/pwrdm ON before a relock").
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

We're no longer requiring struct omap_hwmod records to contain a
clockdomain.  So we shouldn't return -EINVAL any more from
_omap4_wait_target_disable() or _omap4_wait_target_ready() if there's
no clockdomain defined, since that just gets passed back to the
caller.  This can result in pointless warnings under the relaxed data
format.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

This API is meant to be an interface to hwmod assert/deassert
function, omap devices can call them through their platform data to
control their reset lines, they are expected to know the name of the
reset line they are trying to control.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
[paul@pwsan.com: tweaked some documentation; fixed CodingStyle issue]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Several hwmod function prototypes appear to not have an implementation
because the corresponding functions were removed or renamed.
Those prototypes are unneeded anymore - remove them.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[paul@pwsan.com: tweaked subject]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Conflicts:
	arch/arm/mach-omap2/clkt34xx_dpll3m2.c
	arch/arm/mach-omap2/clkt_clksel.c
	arch/arm/mach-omap2/clock.c

From Paul Walmsley <paul@pwsan.com>:

AM33xx hwmod data and miscellaneous clock and hwmod fixes.  AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.

These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.

smatch and string-wrapping cleanups for the OMAP subarch code.

These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.

Basic build, boot, and PM logs are available here:

http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/

The new common clk framework includes basic definitions for mux and
divider clocks.  These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP/AM33XX clk framework
has traditionally used when accessing the register to control the
mux or divisor.

To ease this transition the masks are left intact and
the width field is simply added alongside the shift and mask data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The new common clk framework includes basic definitions for mux and
divider clocks.  These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP clk framework has
traditionally used when accessing the register to control the mux or
divisor.

To ease this transition the masks are left intact and the width field is
simply added alongside the shift and mask data.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

While we move to Common Clk Framework (CCF), direct deferencing of struct
clk wouldn't be possible anymore. Hence get rid of all such instances
in the current clock code and use macros/helpers similar to the ones that
are provided by CCF.

While here also concatenate some strings split across multiple lines
which seem to be needed anyway.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified some compound expressions; reformatted some
 messages]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>

Moving to Common clk framework for OMAP would mean we no longer use
internal lookup mechanism like omap_clk_get_by_name().
get rid of all its usage mostly from hwmod and omap_device
code.

Moving to clk_get() also means the respective platforms
need the clkdev tables updated with an entry for all clocks
used by hwmod to have clock name same as the alias.

Based on original changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
[paul@pwsan.com: removed IS_ERR_OR_NULL() conversion (rmk comment);
 restricted omap_96m_alwon_fck_3630 to OMAP36xx; added missing AM35xx
 clock aliases for emac_fck, emac_ick, vpfe_ick, vpfe_fck; added
 aliases rng_ick and several emulation clocks]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

As part of Common Clk Framework (CCF) the clk_enable() operation
was split into a clk_prepare() which could sleep, and a clk_enable()
which should never sleep. Similarly the clk_disable() was
split into clk_disable() and clk_unprepare(). This was
needed to handle complex cases where in a clk gate/ungate
would require a slow and a fast part to be implemented.
None of the clocks below seem to be in the 'complex' clocks
category and are just simple clocks which are enabled/disabled
through simple register writes.
Most of the instances also seem to be called in non-atomic
context which means its safe to move all of those from
using a clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare().

For some others, mainly the ones handled through the hwmod framework
there is a possibility that they get called in either an atomic
or a non-atomic context.

The way these get handled below work only as long as clk_prepare
is implemented as a no-op (which is the case today) since this gets
called very early at boot while most subsystems are unavailable.
Hence these are marked with a *HACK* comment, which says we need
to re-visit these once we start doing something meaningful with
clk_prepare/clk_unprepare like doing voltage scaling or something
that involves i2c.

This is in preparation of OMAP moving to CCF.

Based on initial changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Remove unnecessary includes of plat/clock.h from the OMAP SPI
controller drivers.  These need to be removed to build multi-subarch
ARM kernels which include these drivers.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

For OMAP4, the dmtimers are located in the Wake-up, ABE and Peripheral (PER)
power domains. Hence, when the dmtimer is configured to use the "timer_sys_ck"
as its functional clock the actual clock used is different depending on whether
the clock is in the Wake-up, ABE or PER domain. So when we look-up the dmtimer's
"timer_sys_ck" we need to specify the timer device name as well as clock alias
to find the right clock.

Currently, the device names for the timers have the format "omap_timer.X" where
X is the timer instance number. When using to device tree, the format of the
device name created by device-tree is different and has the format
"<reg-address>.<device-name>" (this is assuming that the device-tree "reg"
property is specified). This causes the look-up for the OMAP4 "timer_sys_ck" to
fail. To fix this add new timer clock alias for using device-tree.

Please note that adding a 2nd set of clock aliases for the same clocks to only
temporary until device-tree migration is complete. Then we can remove the legacy
aliases. Hence, I have marked the legacy aliases with a "TODO" to remove them.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add AM335x cpu0 clock entry to the corresponding clock data file. This
is useful in getting the correct mpu clock pointer to change the cpu
frequency in cpufreq driver.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[paul@pwsan.com: changed patch subject]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

These clkdev aliases should make it possible to remove the
cpu_is_omap*() calls and the omap_device*() call from
drivers/cpufreq/omap-cpufreq.c during the next merge window.  Those
are interfering with multi-subarch ARM kernels.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>

The platform device name "usbhs_tll" is added for the functional,
interface and channel clocks of the TLL module.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

In commit c59b537d (ARM: OMAP2+: Simplify dmtimer clock aliases) new clock
aliases were added for OMAP2+ devices. For OMAP2420, I incorrectly set the
clock flag as CK_243X instead of CK_242X. This did not introduce a regression
as the clock flags are not checked for OMAP2 devices. This also explains why
I did not catch this when testing on OMAP2420.

Fix the clock flags for these aliases for correctness.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

The file is currently called 'clock3xxx_data.c', so this comment is
out of date.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
[paul@pwsan.com: wrote changelog]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

From Paul Walmsley <paul@pwsan.com>:

AM33xx hwmod data and miscellaneous clock and hwmod fixes.  AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.

These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.

Merge of the LED related changes with omap sparse IRQ and
hardware.h related changes causes a build issue otherwise:

arch/arm/mach-omap1/board-h2.c:319: error: implicit declaration of function ‘OMAP_MPUIO’
arch/arm/mach-omap1/board-h2.c:319: error: initializer element is not constant
arch/arm/mach-omap1/board-h2.c:319: error: (near initialization for ‘h2_gpio_led_pins[1].gpio’)
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable pinctrl dummy states for all OMAP platforms that don't
populate DT. This allows drivers to be converted to pinctrl
and not generate new warnings on platforms that do not provide
pinctrl data. These platforms already have pinmuxes configured
before the drivers probe.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal) broke
compile for non-omap as include plat/cpu.h was added. This header
was indirectly included earlier when SPARSE_IRQ was not set, but
does not exist on most platforms.

Fix the problem by removing the cpu_is_omap usage that should
not exist in drivers at all. We can do this by adding proper
clock aliases for the twl-core.c drivers, and drop separate
handling for cases when clock framework is not available as
the behaviour will stay the same.

Note that we need to add a platform device to avoid using the
i2c provided names that may be different on various omaps.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull mfd fixes from Samuel Ortiz:
 "This is the remaining MFD fixes for 3.6, with 5 pending fixes:

   - A tps65217 build error fix.
   - A lcp_ich regression fix caused by the MFD driver failing to
     initialize the watchdog sub device due to ACPI conflicts.
   - 2 MAX77693 interrupt handling bug fixes.
   - An MFD core fix, adding an IRQ domain argument to the MFD device
     addition API in order to prevent silent and potentially harmful
     remapping behaviour changes for drivers supporting non-DT
     platforms."

* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: MAX77693: Fix NULL pointer error when initializing irqs
  mfd: MAX77693: Fix interrupt handling bug
  mfd: core: Push irqdomain mapping out into devices
  mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
  mfd: Move tps65217 regulator plat data handling to regulator

Pull pwm fixes from Thierry Reding:
 "While this comes a bit later than I had wished, both patches are
  rather minor and touch only new drivers so I think these are still
  safe for merging."

* tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm:
  pwm: pwm-tiehrpwm: Fix conflicting channel period setting
  pwm: pwm-tiecap: Disable APWM mode after configure

Pull scsi target fixes from Nicholas Bellinger:
 "Here is the current set of target-pending fixes headed for v3.6-final

  The main parts of this series include bug-fixes from Paolo Bonzini to
  address an use-after-free bug in pSCSI sense exception handling, along
  with addressing some long-standing bugs wrt the handling of zero-
  length SCSI CDB payloads also specific to pSCSI pass-through device
  backends."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: go through normal processing for zero-length REQUEST_SENSE
  target: support zero allocation length in REQUEST SENSE
  target: support zero-size allocation lengths in transport_kmap_data_sg
  target: fail REPORT LUNS with less than 16 bytes of payload
  target: report too-small parameter lists everywhere
  target: go through normal processing for zero-length PSCSI commands
  target: fix use-after-free with PSCSI sense data
  target: simplify code around transport_get_sense_data
  target: move transport_get_sense_data
  target: Check idr_get_new return value in iscsi_login_zero_tsih_s1
  target: Fix ->data_length re-assignment bug with SCSI overflow

Pull power management fixes from Rafael J. Wysocki:
 "Three ACPI device power management fixes related to checking and
  setting device power states."

* tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Use KERN_DEBUG when no power resources are found
  ACPI / PM: Fix resource_lock dead lock in acpi_power_on_device
  ACPI / PM: Infer parent power state from child if unknown, v2

Pull a btrfs revert from Chris Mason:
 "My for-linus branch has one revert in the new quota code.

  We're building up more fixes at etc for the next merge window, but I'm
  keeping them out unless they are bigger regressions or have a huge
  impact."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Revert "Btrfs: fix some error codes in btrfs_qgroup_inherit()"

Pull more sound fixes from Takashi Iwai:
 "Yet more (a bunch of) small fixes that slipped from the previous pull
  request.  Most of commits are pending ASoC fixes, all of which are
  fairly trivial commits."

* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: wm8904: correct the index
  ALSA: hda - Yet another position_fix quirk for ASUS machines
  ASoC: tegra: fix maxburst settings in dmaengine code
  ASoC: samsung dma - Don't indicate support for pause/resume.
  ASoC: mc13783: Remove mono support
  ASoC: arizona: Fix typo in 44.1kHz rates
  ASoC: spear: correct the check for NULL dma_buffer pointer
  sound: tegra_alc5632: remove HP detect GPIO inversion
  ASoC: atmel-ssc: include linux/io.h for raw io
  ASoC: dapm: Don't force card bias level to be updated
  ASoC: dapm: Make sure we update the bias level for CODECs with no op
  ASoC: am3517evm: fix error return code
  ASoC: ux500_msp_i2s: better use devm functions and fix error return code
  ASoC: imx-sgtl5000: fix error return code

This reverts commit 970e1789.

Nikolay Ulyanitsky reported thatthe 3.6-rc5 kernel has a 15-20%
performance drop on PostgreSQL 9.2 on his machine (running "pgbench").

Borislav Petkov was able to reproduce this, and bisected it to this
commit 970e1789 ("sched: Improve scalability via 'CPU buddies' ...")
apparently because the new single-idle-buddy model simply doesn't find
idle CPU's to reschedule on aggressively enough.

Mike Galbraith suspects that it is likely due to the user-mode spinlocks
in PostgreSQL not reacting well to preemption, but we don't really know
the details - I'll just revert the commit for now.

There are hopefully other approaches to improve scheduler scalability
without it causing these kinds of downsides.
Reported-by: Nikolay Ulyanitsky <lystor@gmail.com>
Bisected-by: Borislav Petkov <bp@alien8.de>
Acked-by: Mike Galbraith <efault@gmx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch fix bug related to interrupt handling for MAX77693 devices.
- Unmask interrupt masking bit for charger/flash/muic to revolve
that interrupt isn't happened when external connector is attached.
- Fix wrong regmap instance when muic interrupt is happened.

This patch were discussed and confirm discussion about this patch on below url:
http://lkml.org/lkml/2012/7/16/118Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties.  This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern.  There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.

Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts.  The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

ASoC: Updates for 3.6

A bigger set of updates than I'm entirely comfortable with - things
backed up a bit due to travel.  As ever the majority of these are small,
focused updates for specific drivers though there are a couple of core
changes.  There's been good exposure in -next.

The AT91 patch fixes a build break.

Pull GFS2 fixes from Steven Whitehouse:
 "Here are three GFS2 fixes for the current kernel tree.  These are all
  related to the block reservation code which was added at the merge
  window.  That code will be getting an update at the forthcoming merge
  window too.  In the mean time though there are a few smaller issues
  which should be fixed.

  The first patch resolves an issue with write sizes of greater than 32
  bits with the size hinting code.  The second ensures that the
  allocation data structure is initialised when using xattrs and the
  third takes into account allocations which may have been made by other
  nodes which affect a reservation on the local node."

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: Take account of blockages when using reserved blocks
  GFS2: Fix missing allocation data for set/remove xattr
  GFS2: Make write size hinting code common