- 08 Nov, 2021 5 commits
-
-
Benjamin Li authored
The linear mapping between the BD rate field and the driver's 5GHz legacy rates table (wcn_5ghz_rates) does not only apply for the latter four rates -- it applies to all eight rates. Fixes: 6ea131ac ("wcn36xx: Fix warning due to bad rate_idx") Signed-off-by:
Benjamin Li <benl@squareup.com> Tested-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211104010548.1107405-3-benl@squareup.com
-
Benjamin Li authored
status.band is used in determination of status.rate -- for 5GHz on legacy rates there is a linear shift between the BD descriptor's rate field and the wcn36xx driver's rate table (wcn_5ghz_rates). We have a special clause to populate status.band for hardware scan offload frames. However, this block occurs after status.rate is already populated. Correctly handle this dependency by moving the band block before the rate block. This patch addresses kernel warnings & missing scan results for 5GHz APs that send their beacons/probe responses at the higher four legacy rates (24-54 Mbps), when using hardware scan offload: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4532 ieee80211_rx_napi+0x744/0x8d8 Modules linked in: wcn36xx [...] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.19.107-g73909fa #1 Hardware name: Square, Inc. T2 (all variants) (DT) Call trace: dump_backtrace+0x0/0x148 show_stack+0x14/0x1c dump_stack+0xb8/0xf0 __warn+0x2ac/0x2d8 warn_slowpath_null+0x44/0x54 ieee80211_rx_napi+0x744/0x8d8 ieee80211_tasklet_handler+0xa4/0xe0 tasklet_action_common+0xe0/0x118 tasklet_action+0x20/0x28 __do_softirq+0x108/0x1ec irq_exit+0xd4/0xd8 __handle_domain_irq+0x84/0xbc gic_handle_irq+0x4c/0xb8 el1_irq+0xe8/0x190 lpm_cpuidle_enter+0x220/0x260 cpuidle_enter_state+0x114/0x1c0 cpuidle_enter+0x34/0x48 do_idle+0x150/0x268 cpu_startup_entry+0x20/0x24 rest_init+0xd4/0xe0 start_kernel+0x398/0x430 ---[ end trace ae28cb759352b403 ]--- Fixes: 8a27ca39 ("wcn36xx: Correct band/freq reporting on RX") Signed-off-by:
-
Bryan O'Donoghue authored
When deiniting the DXE hardware we should reset the block to ensure there is no spurious DMA write transaction from the downstream WCNSS to upstream MSM at a skbuff address we will have released. Fixes: 8e84c258 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
-
Bryan O'Donoghue authored
When unloading the driver we are not releasing the DMA descriptors which we previously allocated. Fixes: 8e84c258 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by:
-
Bryan O'Donoghue authored
Right now we have a broken sequence where we enable DMA channel interrupts which can be left enabled and never disabled if we hit an error path. Worse still when we unload the driver, the DMA channel interrupt bits are left intact. About the only saving grace here is that we do remember to disable the wcnss interrupt when unload the driver. Fixes: 8e84c258 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by:
-
- 01 Nov, 2021 7 commits
-
-
Yang Guang authored
Using swap() make it more readable. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Yang Guang <yang.guang5@zte.com.cn> Signed-off-by:
-
Bryan O'Donoghue authored
Firmware can trigger a missed beacon indication, this is not the same as a lost signal. Flag to Linux the missed beacon and let the WiFi stack decide for itself if the link is up or down by sending its own probe to determine this. We should only be signalling the link is lost when the firmware indicates Fixes: 8e84c258 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by:
-
Benjamin Li authored
An SMD capture from the downstream prima driver on WCN3680B shows the following command sequence for connected scans: - init_scan_req - start_scan_req, channel 1 - end_scan_req, channel 1 - start_scan_req, channel 2 - ... - end_scan_req, channel 3 - finish_scan_req - init_scan_req - start_scan_req, channel 4 - ... - end_scan_req, channel 6 - finish_scan_req - ... - end_scan_req, channel 165 - finish_scan_req Upstream currently never calls wcn36xx_smd_end_scan, and in some cases[1] still sends finish_scan_req twice in a row or before init_scan_req. A typical connected scan looks like this: - init_scan_req - start_scan_req, channel 1 - finish_scan_req - init_scan_req - start_scan_req, channel 2 - ... - start_scan_req, channel 165 - finish_scan_req - finish_scan_req This patch cleans up scanning so that init/finish and start/end are always paired together and correctly nested. - init_scan_req - start_scan_req, channel 1 - end_scan_req, channel 1 - finish_scan_req - init_scan_req - start_scan_req, channel 2 - end_scan_req, channel 2 - ... - start_scan_req, channel 165 - end_scan_req, channel 165 - finish_scan_req Note that upstream will not do batching of 3 active-probe scans before returning to the operating channel, and this patch does not change that. To match downstream in this aspect, adjust IEEE80211_PROBE_DELAY and/or the 125ms max off-channel time in ieee80211_scan_state_decision. [1]: commit d195d7aa ("wcn36xx: Ensure finish scan is not requested before start scan") addressed one case of finish_scan_req being sent without a preceding init_scan_req (the case of the operating channel coinciding with the first scan channel); two other cases are: 1) if SW scan is started and aborted immediately, without scanning any channels, we send a finish_scan_req without ever sending init_scan_req, and 2) as SW scan logic always returns us to the operating channel before calling wcn36xx_sw_scan_complete, finish_scan_req is always sent twice at the end of a SW scan Fixes: 8e84c258 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: -
Benjamin Li authored
Without ieee80211_ops->flush implemented to empty HW queues, mac80211 will do a 100ms dead wait after stopping SW queues, before leaving the operating channel to resume a software connected scan[1]. (see ieee80211_scan_state_resume) This wait is correctly included in the calculation for whether or not we've exceeded max off-channel time, as it occurs after sending the null frame with PS bit set. Thus, with 125 ms max off-channel time we only have 25 ms of scan time, which technically isn't even enough to scan one channel (although mac80211 always scans at least one channel per off- channel window). Moreover, for passive probes we end up spending at least 100 ms + 111 ms (IEEE80211_PASSIVE_CHANNEL_TIME) "off-channel"[2], which exceeds the listen interval of 200 ms that we provide in our association request frame. That's technically out-of-spec. [1]: Until recently, wcn36xx performed software (rather than FW-offloaded) scanning when 5GHz channels are requested. This apparent limitation is now resolved -- see commit 1395f8a6a4d5 ("wcn36xx: Enable hardware scan offload for 5Ghz band"). [2]: in quotes because about 100 ms of it is still on-channel but with PS set Signed-off-by: -
Benjamin Li authored
Add some MAC debug prints for more easily demarcating a software scan when parsing logs. Signed-off-by:
-
Christian Lamparter authored
ATH10K chips are used it wide range of routers, accesspoints, range extenders, network appliances. On these embedded devices, calibration data is often stored on the main system's flash and was out of reach for the driver. To bridge this gap, ath10k is getting extended to pull the (pre-)calibration data through nvmem subsystem. To do this, a nvmem-cell containing the information can either be specified in the platform data or via device-tree. Tested with: Netgear EX6150v2 (IPQ4018 - pre-calibration method) TP-Link Archer C7 v2 (QCA9880v2 - old calibration method) Cc: Robert Marko <robimarko@gmail.com> Cc: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by:Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Wen Gong authored
Commit 6f4d7030 ("ath11k: support SMPS configuration for 6 GHz") changed "if (ht_cap & WMI_HT_CAP_DYNAMIC_SMPS)" to "if (ht_cap & WMI_HT_CAP_DYNAMIC_SMPS || ar->supports_6ghz)" which means NL80211_FEATURE_DYNAMIC_SMPS is enabled for all chips which support 6 GHz. However, WCN6855 supports 6 GHz but it does not support feature NL80211_FEATURE_DYNAMIC_SMPS, and this can lead to MU-MIMO test failures for WCN6855. Disable NL80211_FEATURE_DYNAMIC_SMPS for WCN6855 since its ht_cap does not support WMI_HT_CAP_DYNAMIC_SMPS. Enable the feature only on QCN9074 as that's the only other device supporting 6 GHz band. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
Jouni Malinen <jouni@codeaurora.org> Signed-off-by:
-
- 28 Oct, 2021 7 commits
-
-
Johan Hovold authored
Add the missing endpoint max-packet sanity check to probe() to avoid division by zero in ath10k_usb_hif_tx_sg() in case a malicious device has broken descriptors (or when doing descriptor fuzz testing). Note that USB core will reject URBs submitted for endpoints with zero wMaxPacketSize but that drivers doing packet-size calculations still need to handle this (cf. commit 2548288b ("USB: Fix: Don't skip endpoint descriptors with maxpacket=0")). Fixes: 9cbee358 ("ath6kl: add full USB support") Cc: stable@vger.kernel.org # 3.5 Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
Add the missing endpoint max-packet sanity check to probe() to avoid division by zero in ath10k_usb_hif_tx_sg() in case a malicious device has broken descriptors (or when doing descriptor fuzz testing). Note that USB core will reject URBs submitted for endpoints with zero wMaxPacketSize but that drivers doing packet-size calculations still need to handle this (cf. commit 2548288b ("USB: Fix: Don't skip endpoint descriptors with maxpacket=0")). Fixes: 4db66499 ("ath10k: add initial USB support") Cc: stable@vger.kernel.org # 4.14 Cc: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by:
-
Johan Hovold authored
USB control-message timeouts are specified in milliseconds and should specifically not vary with CONFIG_HZ. Fixes: 241b128b ("ath6kl: add back beginnings of USB support") Cc: stable@vger.kernel.org # 3.4 Signed-off-by:
-
Johan Hovold authored
USB control-message timeouts are specified in milliseconds and should specifically not vary with CONFIG_HZ. Fixes: 4db66499 ("ath10k: add initial USB support") Cc: stable@vger.kernel.org # 4.14 Cc: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by:
-
Benjamin Li authored
The official feature-complete WCN3680B driver (known as prima, open source but not upstream) supports channels 136 and 144. However, these channels are missing in upstream. Add them here to get closer to feature parity with prima. Signed-off-by:
-
Benjamin Li authored
The official feature-complete WCN3680B driver (known as prima, open source but not upstream) sends this feature bit. As we wish to support the antenna diversity feature in upstream, we need to set this bit as well. Signed-off-by:
-
Loic Poulain authored
The channel scan list must be updated before triggering a hardware scan so that firmware takes into account the regulatory info for each single channel such as active/passive config, power, DFS, etc... Without this the firmware uses its own internal default channel configuration, which is not aligned with mac80211 regulatory rules, and misses several channels (e.g. 144). Fixes: 2f3bef4b ("wcn36xx: Add hardware scan offload support") Signed-off-by:
-
- 27 Oct, 2021 10 commits
-
-
Bryan O'Donoghue authored
Firmware link offload monitoring can be made to work in 3/4 cases by switching on firmware feature bit WLANACTIVE_OFFLOAD - Secure power-save on - Secure power-save off - Open power-save on However, with an open AP if we switch off power-saving - thus never entering Beacon Mode Power Save - BMPS, firmware never forwards loss of beacon upwards. We had hoped that WLANACTIVE_OFFLOAD and some fixes for sequence numbers would unblock this but, it hasn't and further investigation is required. Its possible to have a complete set of Secure power-save on/off and Open power-save on/off provided we use Linux' link monitoring mechanism. While we debug the Open AP failure we need to fix upstream. This reverts commit c973fdad79f6eaf247d48b5fc77733e989eb01e1. Signed-off-by:
-
Loic Poulain authored
If the system is resumed because of an incoming packet, the wcn36xx RX interrupts is fired before actual resuming of the wireless/mac80211 stack, causing any received packets to be simply dropped. E.g. a ping request causes a system resume, but is dropped and so never forwarded to the IP stack. This change fixes that, disabling DMA interrupts on suspend to no pass packets until mac80211 is resumed and ready to handle them. Note that it's not incompatible with RX irq wake. Signed-off-by:
-
Loic Poulain authored
The firmware is offering features such as ARP offload, for which firmware crafts its own (QoS)packets without waking up the host. Point is that the sequence numbers generated by the firmware are not in sync with the host mac80211 layer and can cause packets such as firmware ARP reponses to be dropped by the AP (too old SN). To fix this we need to let the firmware manages the sequence numbers by its own (except for QoS null frames). There is a SN counter for each QoS queue and one global/baseline counter for Non-QoS. Fixes: 84aff52e ("wcn36xx: Use sequence number allocated by mac80211") Signed-off-by:
-
Benjamin Li authored
This is essentially exactly following the dma_wmb()/dma_rmb() usage instructions in Documentation/memory-barriers.txt. The theoretical races here are: 1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l write, thus performing DMA into the wrong address. 2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl & WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb). Fixes: 8e84c258 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by:
-
Loic Poulain authored
All wcn36xx controllers are supposed to support HT40 (and SGI40), This doubles the maximum bitrate/throughput with compatible APs. Tested with wcn3620 & wcn3680B. Cc: stable@vger.kernel.org Fixes: 8e84c258 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by:
-
Bryan O'Donoghue authored
This reverts commit c6522a50. Testing on tip-of-tree shows that this is working now. Revert this and re-enable BMPS for Open APs. Signed-off-by:
-
Bryan O'Donoghue authored
On an open AP when you pull the plug on the AP, if we are not already in BMPS mode then the firmware will not generate a disconnection event. Instead we need to monitor for failure to enter BMPS and treat a string of failures as connection loss. Secure AP connections don't appear to demonstrate this behavior so the work-around is limited to open APs only. Signed-off-by:
-
Loic Poulain authored
WCNSS RX DMA transfer support is limited to 3872 bytes, which is enough for simple MPDUs (single MSDU), but not enough for cases with A-MSDU (depending on max AMSDU size or max MPDU size). In that case the MPDU is spread over multiple transfers, with the first transfer containing the MPDU header and (at least) the first A-MSDU subframe and additional transfer(s) containing the following A-MSDUs. This can be handled with a series of flags to tagging the first and last A-MSDU transfers. In that case we have to bufferize and re-linearize the A-MSDU buffers into a proper MPDU skb before forwarding to mac80211 (in the same way as it is done in ath10k). This change also includes sanity check of the buffer descriptor to prevent skb overflow. Signed-off-by:
-
Loic Poulain authored
Until now, offload scanning for 5Ghz channels was considered broken. However it was mostly a driver issue, caused by bad reporting of the beacons/probe-resp bands and frequencies, which has been fixed. We can now allow offload scan for 5GHz band, this reduces the scanning time comparing to software driven scanning. Note that offloaded scan is limited to 48 channels, check for this. Signed-off-by:
-
Loic Poulain authored
For packets originating from hardware scan, the channel and band is included in the buffer descriptor (bd->rf_band & bd->rx_ch). For 2Ghz band the channel value is directly reported in the 4-bit rx_ch field. For 5Ghz band, the rx_ch field contains a mapping index (given the 4-bit limitation). The reserved0 value field is also used to extend 4-bit mapping to 5-bit mapping to support more than 16 5Ghz channels. This change adds correct reporting of the frequency/band, that is used in scan mechanism. And is required for 5Ghz hardware scan support. Signed-off-by:
-
- 25 Oct, 2021 5 commits
-
-
Loic Poulain authored
This change fix the TX ack mechanism in various ways: - For NO_ACK tagged packets, we don't need to wait for TX_ACK indication and so are not subject to the single packet ack limitation. So we don't have to stop the tx queue, and can call the tx status callback as soon as DMA transfer has completed. - Fix skb ownership/reference. Only start status indication timeout once the DMA transfer has been completed. This avoids the skb to be both referenced in the DMA tx ring and by the tx_ack_skb pointer, preventing any use-after-free or double-free. - This adds a sanity (paranoia?) check on the skb tx ack pointer. - Resume TX queue if TX status tagged packet TX fails. Cc: stable@vger.kernel.org Fixes: fdf21cc3 ("wcn36xx: Add TX ack support") Signed-off-by:
-
Loic Poulain authored
We observe unexpected connection drops with some APs due to non-acked mac80211 generated null data frames (keep-alive). After debugging and capture, we noticed that null frames are submitted at standard data bitrate and that the given APs are in trouble with that. After setting the null frame bitrate to control bitrate, all null frames are acked as expected and connection is maintained. Not sure if it's a requirement of the specification, but it seems the right thing to do anyway, null frames are mostly used for control purpose (power-saving, keep-alive...), and submitting them with a slower/simpler bitrate/modulation is more robust. Cc: stable@vger.kernel.org Fixes: 512b191d ("wcn36xx: Fix TX data path") Signed-off-by:
-
Abinaya Kalaiselvan authored
Commit 9af7c32c ("ath10k: add target IRAM recovery feature support") introduced a new firmware feature flag ATH10K_FW_FEATURE_IRAM_RECOVERY. But this caused ath10k_pci module load to fail if ATH10K_FW_CRASH_DUMP_RAM_DATA bit was not enabled in the ath10k coredump_mask module parameter: [ 2209.328190] ath10k_pci 0000:02:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 2209.434414] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1 [ 2209.547191] ath10k_pci 0000:02:00.0: firmware ver 10.4-3.9.0.2-00099 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 cbade90a [ 2210.896485] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id 0:1 crc32 a040efc2 [ 2213.603339] ath10k_pci 0000:02:00.0: failed to copy target iram contents: -12 [ 2213.839027] ath10k_pci 0000:02:00.0: could not init core (-12) [ 2213.933910] ath10k_pci 0000:02:00.0: could not probe fw (-12) And by default coredump_mask does not have ATH10K_FW_CRASH_DUMP_RAM_DATA enabled so anyone using a firmware with iram-recovery feature would fail. To my knowledge only QCA9984 firmwares starting from release 10.4-3.9.0.2-00099 enabled the feature. The reason for regression was that ath10k_core_copy_target_iram() used ath10k_coredump_get_mem_layout() to get the memory layout, but when ATH10K_FW_CRASH_DUMP_RAM_DATA was disabled it would get just NULL and bail out with an error. While looking at all this I noticed another bug: if CONFIG_DEV_COREDUMP is disabled but the firmware has iram-recovery enabled the module load fails with similar error messages. I fixed that by returning 0 from ath10k_core_copy_target_iram() when _ath10k_coredump_get_mem_layout() returns NULL. Tested-on: QCA9984 hw2.0 PCI 10.4-3.9.0.2-00139 Fixes: 9af7c32c ("ath10k: add target IRAM recovery feature support") Signed-off-by:
Abinaya Kalaiselvan <akalaise@codeaurora.org> Signed-off-by:
-
Arnd Bergmann authored
Using a kernel pointer in place of a dma_addr_t token can lead to undefined behavior if that makes it into cache management functions. The compiler caught one such attempt in a cast: drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_add_interface': drivers/net/wireless/ath/ath10k/mac.c:5586:47: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast] 5586 | arvif->beacon_paddr = (dma_addr_t)arvif->beacon_buf; | ^ Looking through how this gets used down the way, I'm fairly sure that beacon_paddr is never accessed again for ATH10K_DEV_TYPE_HL devices, and if it was accessed, that would be a bug. Change the assignment to use a known-invalid address token instead, which avoids the warning and makes it easier to catch bugs if it does end up getting used. Fixes: e263bdab ("ath10k: high latency fixes for beacon buffer") Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Baochen Qiang authored
QCA6390 firmware uses HAL_RX_BUF_RBM_SW1_BM, not HAL_RX_BUF_RBM_SW3_BM. This is needed to fix a case where an A-MSDU has an unexpected LLC/SNAP header in the first subframe (CVE-2020-24588). Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by:
Baochen Qiang <bqiang@codeaurora.org> Signed-off-by:
-
- 20 Oct, 2021 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.16. Major changes: ath9k * add option to reset the wifi chip via debugfs * convert Device Tree bindings to the json-schema * support Device Tree ieee80211-freq-limit property to limit channels
-
Jonas Dreßler authored
When powersaving (so either wifi powersaving or deep sleep, depending on which state the firmware is in) is disabled, the way the firmware goes into host sleep is different: Usually the firmware implicitely enters host sleep on the next SLEEP event we get when we configured host sleep via HSCFG before. When powersaving is disabled though, there are no SLEEP events, the way we enter host sleep in that case is different: The firmware will send us a HS_ACT_REQ event and after that we "manually" make the firmware enter host sleep by sending it another HSCFG command with the action HS_ACTIVATE. Now waking up from host sleep appears to be different depending on whether powersaving is enabled again: When powersaving is enabled, the firmware implicitely leaves host sleep as soon as it wakes up and sends us an AWAKE event. When powersaving is disabled though, it apparently doesn't implicitely leave host sleep, but instead we need to send it a HSCFG command with the HS_CONFIGURE action and the HS_CFG_CANCEL condition. We didn't do that so far, which is why waking up from host sleep was broken when powersaving is disabled. So add some additional state to mwifiex_adapter where we keep track of whether host sleep was activated manually via HS_ACTIVATE, and if that was the case, deactivate it manually again via HS_CFG_CANCEL. Signed-off-by:
Jonas Dreßler <verdre@v0yd.nl> Signed-off-by:
-
Jonas Dreßler authored
While looking at on-air packets using Wireshark, I noticed we're never setting the initiator bit when sending DELBA requests to the AP: While we set the bit on our del_ba_param_set bitmask, we forget to actually copy that bitmask over to the command struct, which means we never actually set the initiator bit. Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command struct. Fixes: 5e6e3a92 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by:
Pali Rohár <pali@kernel.org> Signed-off-by:
-
Jonas Dreßler authored
We're sending DELBA requests here, not ADDBA requests. Signed-off-by:
-
Jonas Dreßler authored
Sometimes the KEY_MATERIAL command can fail with the 88W8897 firmware (when this happens exactly seems pretty random). This appears to prevent the access point from starting, so it seems like a good idea to log an error in that case. Signed-off-by:
-
Jonas Dreßler authored
It's not an error if someone chooses to put their computer to sleep, not wanting it to wake up because the person next door has just discovered what a magic packet is. So change the loglevel of this annoying message from ERROR to INFO. Signed-off-by:
-
