Skip to content

L
linux
Switch branch/tag
  1. 15 Mar, 2016 22 commits
    • Maximilain Schneider's avatar
      can: gs_usb: fixed disconnect bug by removing erroneous use of kfree() · d5d92e5d
      Maximilain Schneider authored 
      commit e9a2d81b upstream.

gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is
allocated through alloc_candev() and should instead be freed using
free_candev() alone.

The inappropriate use of kfree() causes the kernel to hang when
gs_destroy_candev() is called.

Only the struct gs_usb * which is allocated through kzalloc() should be freed
using kfree() when the device is disconnected.
Signed-off-by: default avatarMaximilian Schneider <max@schneidersoft.net>
Signed-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      d5d92e5d
    • Harvey Hunt's avatar
      libata: Align ata_device's id on a cacheline · 3f748d58
      Harvey Hunt authored 
      commit 4ee34ea3 upstream.

The id buffer in ata_device is a DMA target, but it isn't explicitly
cacheline aligned. Due to this, adjacent fields can be overwritten with
stale data from memory on non coherent architectures. As a result, the
kernel is sometimes unable to communicate with an ATA device.

Fix this by ensuring that the id buffer is cacheline aligned.

This issue is similar to that fixed by Commit 84bda12a
("libata: align ap->sector_buf").
Signed-off-by: default avatarHarvey Hunt <harvey.hunt@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: default avatarTejun Heo <tj@kernel.org>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      3f748d58
    • Jay Cornwall's avatar
      iommu/amd: Apply workaround for ATS write permission check · 6f94880f
      Jay Cornwall authored 
      commit 358875fd upstream.

The AMD Family 15h Models 30h-3Fh (Kaveri) BIOS and Kernel Developer's
Guide omitted part of the BIOS IOMMU L2 register setup specification.
Without this setup the IOMMU L2 does not fully respect write permissions
when handling an ATS translation request.

The IOMMU L2 will set PTE dirty bit when handling an ATS translation with
write permission request, even when PTE RW bit is clear. This may occur by
direct translation (which would cause a PPR) or by prefetch request from
the ATC.

This is observed in practice when the IOMMU L2 modifies a PTE which maps a
pagecache page. The ext4 filesystem driver BUGs when asked to writeback
these (non-modified) pages.

Enable ATS write permission check in the Kaveri IOMMU L2 if BIOS has not.
Signed-off-by: default avatarJay Cornwall <jay@jcornwall.me>
Signed-off-by: default avatarJoerg Roedel <jroedel@suse.de>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      6f94880f
    • Suravee Suthikulpanit's avatar
      iommu/amd: Fix boot warning when device 00:00.0 is not iommu covered · 29c64480
      Suravee Suthikulpanit authored 
      commit 38e45d02 upstream.

The setup code for the performance counters in the AMD IOMMU driver
tests whether the counters can be written. It tests to setup a counter
for device 00:00.0, which fails on systems where this particular device
is not covered by the IOMMU.

Fix this by not relying on device 00:00.0 but only on the IOMMU being
present.
Signed-off-by: default avatarSuravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: default avatarJoerg Roedel <jroedel@suse.de>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      29c64480
    • David Woodhouse's avatar
      Fix directory hardlinks from deleted directories · 56026631
      David Woodhouse authored 
      commit be629c62 upstream.

When a directory is deleted, we don't take too much care about killing off
all the dirents that belong to it — on the basis that on remount, the scan
will conclude that the directory is dead anyway.

This doesn't work though, when the deleted directory contained a child
directory which was moved *out*. In the early stages of the fs build
we can then end up with an apparent hard link, with the child directory
appearing both in its true location, and as a child of the original
directory which are this stage of the mount process we don't *yet* know
is defunct.

To resolve this, take out the early special-casing of the "directories
shall not have hard links" rule in jffs2_build_inode_pass1(), and let the
normal nlink processing happen for directories as well as other inodes.

Then later in the build process we can set ic->pino_nlink to the parent
inode#, as is required for directories during normal operaton, instead
of the nlink. And complain only *then* about hard links which are still
in evidence even after killing off all the unreachable paths.
Reported-by: default avatarLiu Song <liu.song11@zte.com.cn>
Signed-off-by: default avatarDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      56026631
    • David Woodhouse's avatar
      jffs2: Fix page lock / f->sem deadlock · 5e357750
      David Woodhouse authored 
      commit 49e91e70 upstream.

With this fix, all code paths should now be obtaining the page lock before
f->sem.
Reported-by: default avatarSzabó Tamás <sztomi89@gmail.com>
Tested-by: default avatarThomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: default avatarDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      5e357750
    • Thomas Betker's avatar
      Revert "jffs2: Fix lock acquisition order bug in jffs2_write_begin" · 50cc195e
      Thomas Betker authored 
      commit 157078f6 upstream.

This reverts commit 5ffd3412
("jffs2: Fix lock acquisition order bug in jffs2_write_begin").

The commit modified jffs2_write_begin() to remove a deadlock with
jffs2_garbage_collect_live(), but this introduced new deadlocks found
by multiple users. page_lock() actually has to be called before
mutex_lock(&c->alloc_sem) or mutex_lock(&f->sem) because
jffs2_write_end() and jffs2_readpage() are called with the page locked,
and they acquire c->alloc_sem and f->sem, resp.

In other words, the lock order in jffs2_write_begin() was correct, and
it is the jffs2_garbage_collect_live() path that has to be changed.

Revert the commit to get rid of the new deadlocks, and to clear the way
for a better fix of the original deadlock.
Reported-by: default avatarDeng Chao <deng.chao1@zte.com.cn>
Reported-by: default avatarMing Liu <liu.ming50@gmail.com>
Reported-by: default avatarwangzaiwei <wangzaiwei@top-vision.cn>
Signed-off-by: default avatarThomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: default avatarDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      50cc195e
    • Peter Chen's avatar
      usb: chipidea: otg: change workqueue ci_otg as freezable · fb41d31f
      Peter Chen authored 
      commit d144dfea upstream.

If we use USB ID pin as wakeup source, and there is a USB block
device on this USB OTG (ID) cable, the system will be deadlock
after system resume.

The root cause for this problem is: the workqueue ci_otg may try
to remove hcd before the driver resume has finished, and hcd will
disconnect the device on it, then, it will call device_release_driver,
and holds the device lock "dev->mutex", but it is never unlocked since
it waits workqueue writeback to run to flush the block information, but
the workqueue writeback is freezable, it is not thawed before driver
resume has finished.

When the driver (device: sd 0:0:0:0:) resume goes to dpm_complete, it
tries to get its device lock "dev->mutex", but it can't get it forever,
then the deadlock occurs. Below call stacks show the situation.

So, in order to fix this problem, we need to change workqueue ci_otg
as freezable, then the work item in this workqueue will be run after
driver's resume, this workqueue will not be blocked forever like above
case since the workqueue writeback has been thawed too.

Tested at: i.mx6qdl-sabresd and i.mx6sx-sdb.

[  555.178869] kworker/u2:13   D c07de74c     0   826      2 0x00000000
[  555.185310] Workqueue: ci_otg ci_otg_work
[  555.189353] Backtrace:
[  555.191849] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  555.198912]  r10:ee471ba0 r9:00000000 r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4
[  555.206867]  r4:ee470000
[  555.209453] [<c07dec24>] (schedule) from [<c07e2fc4>] (schedule_timeout+0x15c/0x1e0)
[  555.217212]  r4:7fffffff r3:edc2b000
[  555.220862] [<c07e2e68>] (schedule_timeout) from [<c07df6c8>] (wait_for_common+0x94/0x144)
[  555.229140]  r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4 r4:7fffffff
[  555.235980] [<c07df634>] (wait_for_common) from [<c07df790>] (wait_for_completion+0x18/0x1c)
[  555.244430]  r10:00000001 r9:c0b5563c r8:c0042e48 r7:ef086000 r6:eea4372c r5:ef131b00
[  555.252383]  r4:00000000
[  555.254970] [<c07df778>] (wait_for_completion) from [<c0043cb8>] (flush_work+0x19c/0x234)
[  555.263177] [<c0043b1c>] (flush_work) from [<c0043fac>] (flush_delayed_work+0x48/0x4c)
[  555.271106]  r8:ed5b5000 r7:c0b38a3c r6:eea439cc r5:eea4372c r4:eea4372c
[  555.277958] [<c0043f64>] (flush_delayed_work) from [<c00eae18>] (bdi_unregister+0x84/0xec)
[  555.286236]  r4:eea43520 r3:20000153
[  555.289885] [<c00ead94>] (bdi_unregister) from [<c02c2154>] (blk_cleanup_queue+0x180/0x29c)
[  555.298250]  r5:eea43808 r4:eea43400
[  555.301909] [<c02c1fd4>] (blk_cleanup_queue) from [<c0417914>] (__scsi_remove_device+0x48/0xb8)
[  555.310623]  r7:00000000 r6:20000153 r5:ededa950 r4:ededa800
[  555.316403] [<c04178cc>] (__scsi_remove_device) from [<c0415e90>] (scsi_forget_host+0x64/0x68)
[  555.325028]  r5:ededa800 r4:ed5b5000
[  555.328689] [<c0415e2c>] (scsi_forget_host) from [<c0409828>] (scsi_remove_host+0x78/0x104)
[  555.337054]  r5:ed5b5068 r4:ed5b5000
[  555.340709] [<c04097b0>] (scsi_remove_host) from [<c04cdfcc>] (usb_stor_disconnect+0x50/0xb4)
[  555.349247]  r6:ed5b56e4 r5:ed5b5818 r4:ed5b5690 r3:00000008
[  555.355025] [<c04cdf7c>] (usb_stor_disconnect) from [<c04b3bc8>] (usb_unbind_interface+0x78/0x25c)
[  555.363997]  r8:c13919b4 r7:edd3c000 r6:edd3c020 r5:ee551c68 r4:ee551c00 r3:c04cdf7c
[  555.371892] [<c04b3b50>] (usb_unbind_interface) from [<c03dc248>] (__device_release_driver+0x8c/0x118)
[  555.381213]  r10:00000001 r9:edd90c00 r8:c13919b4 r7:ee551c68 r6:c0b546e0 r5:c0b5563c
[  555.389167]  r4:edd3c020
[  555.391752] [<c03dc1bc>] (__device_release_driver) from [<c03dc2fc>] (device_release_driver+0x28/0x34)
[  555.401071]  r5:edd3c020 r4:edd3c054
[  555.404721] [<c03dc2d4>] (device_release_driver) from [<c03db304>] (bus_remove_device+0xe0/0x110)
[  555.413607]  r5:edd3c020 r4:ef17f04c
[  555.417253] [<c03db224>] (bus_remove_device) from [<c03d8128>] (device_del+0x114/0x21c)
[  555.425270]  r6:edd3c028 r5:edd3c020 r4:ee551c00 r3:00000000
[  555.431045] [<c03d8014>] (device_del) from [<c04b1560>] (usb_disable_device+0xa4/0x1e8)
[  555.439061]  r8:edd3c000 r7:eded8000 r6:00000000 r5:00000001 r4:ee551c00
[  555.445906] [<c04b14bc>] (usb_disable_device) from [<c04a8e54>] (usb_disconnect+0x74/0x224)
[  555.454271]  r9:edd90c00 r8:ee551000 r7:ee551c68 r6:ee551c9c r5:ee551c00 r4:00000001
[  555.462156] [<c04a8de0>] (usb_disconnect) from [<c04a8fb8>] (usb_disconnect+0x1d8/0x224)
[  555.470259]  r10:00000001 r9:edd90000 r8:ee471e2c r7:ee551468 r6:ee55149c r5:ee551400
[  555.478213]  r4:00000001
[  555.480797] [<c04a8de0>] (usb_disconnect) from [<c04ae5ec>] (usb_remove_hcd+0xa0/0x1ac)
[  555.488813]  r10:00000001 r9:ee471eb0 r8:00000000 r7:ef3d9500 r6:eded810c r5:eded80b0
[  555.496765]  r4:eded8000
[  555.499351] [<c04ae54c>] (usb_remove_hcd) from [<c04d4158>] (host_stop+0x28/0x64)
[  555.506847]  r6:eeb50010 r5:eded8000 r4:eeb51010
[  555.511563] [<c04d4130>] (host_stop) from [<c04d09b8>] (ci_otg_work+0xc4/0x124)
[  555.518885]  r6:00000001 r5:eeb50010 r4:eeb502a0 r3:c04d4130
[  555.524665] [<c04d08f4>] (ci_otg_work) from [<c00454f0>] (process_one_work+0x194/0x420)
[  555.532682]  r6:ef086000 r5:eeb502a0 r4:edc44480
[  555.537393] [<c004535c>] (process_one_work) from [<c00457b0>] (worker_thread+0x34/0x514)
[  555.545496]  r10:edc44480 r9:ef086000 r8:c0b1a100 r7:ef086034 r6:00000088 r5:edc44498
[  555.553450]  r4:ef086000
[  555.556032] [<c004577c>] (worker_thread) from [<c004bab4>] (kthread+0xdc/0xf8)
[  555.563268]  r10:00000000 r9:00000000 r8:00000000 r7:c004577c r6:edc44480 r5:eddc15c0
[  555.571221]  r4:00000000
[  555.573804] [<c004b9d8>] (kthread) from [<c000fef0>] (ret_from_fork+0x14/0x24)
[  555.581040]  r7:00000000 r6:00000000 r5:c004b9d8 r4:eddc15c0

[  553.429383] sh              D c07de74c     0   694    691 0x00000000
[  553.435801] Backtrace:
[  553.438295] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  553.445358]  r10:edd3c054 r9:edd3c078 r8:edddbd50 r7:edcbbc00 r6:c1377c34 r5:60000153
[  553.453313]  r4:eddda000
[  553.455896] [<c07dec24>] (schedule) from [<c07deff8>] (schedule_preempt_disabled+0x10/0x14)
[  553.464261]  r4:edd3c058 r3:0000000a
[  553.467910] [<c07defe8>] (schedule_preempt_disabled) from [<c07e0bbc>] (mutex_lock_nested+0x1a0/0x3e8)
[  553.477254] [<c07e0a1c>] (mutex_lock_nested) from [<c03e927c>] (dpm_complete+0xc0/0x1b0)
[  553.485358]  r10:00561408 r9:edd3c054 r8:c0b4863c r7:edddbd90 r6:c0b485d8 r5:edd3c020
[  553.493313]  r4:edd3c0d0
[  553.495896] [<c03e91bc>] (dpm_complete) from [<c03e9388>] (dpm_resume_end+0x1c/0x20)
[  553.503652]  r9:00000000 r8:c0b1a9d0 r7:c1334ec0 r6:c1334edc r5:00000003 r4:00000010
[  553.511544] [<c03e936c>] (dpm_resume_end) from [<c0079894>] (suspend_devices_and_enter+0x158/0x504)
[  553.520604]  r4:00000000 r3:c1334efc
[  553.524250] [<c007973c>] (suspend_devices_and_enter) from [<c0079e74>] (pm_suspend+0x234/0x2cc)
[  553.532961]  r10:00561408 r9:ed6b7300 r8:00000004 r7:c1334eec r6:00000000 r5:c1334ee8
[  553.540914]  r4:00000003
[  553.543493] [<c0079c40>] (pm_suspend) from [<c0078a6c>] (state_store+0x6c/0xc0)

[  555.703684] 7 locks held by kworker/u2:13/826:
[  555.708140]  #0:  ("%s""ci_otg"){++++.+}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.716277]  #1:  ((&ci->work)){+.+.+.}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.724317]  #2:  (usb_bus_list_lock){+.+.+.}, at: [<c04ae5e4>] usb_remove_hcd+0x98/0x1ac
[  555.732626]  #3:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.740403]  #4:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.748179]  #5:  (&dev->mutex){......}, at: [<c03dc2f4>] device_release_driver+0x20/0x34
[  555.756487]  #6:  (&shost->scan_mutex){+.+.+.}, at: [<c04097d0>] scsi_remove_host+0x20/0x104

Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: default avatarPeter Chen <peter.chen@nxp.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      fb41d31f
    • Felix Fietkau's avatar
      mac80211: minstrel_ht: set default tx aggregation timeout to 0 · b5873124
      Felix Fietkau authored 
      commit 7a36b930 upstream.

The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.

Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Acked-by: default avatarAvery Pennarun <apenwarr@gmail.com>
Signed-off-by: default avatarFelix Fietkau <nbd@openwrt.org>
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      b5873124
    • Charles Keepax's avatar
      ASoC: samsung: Use IRQ safe spin lock calls · a7b55a4f
      Charles Keepax authored 
      commit 316fa9e0 upstream.

Lockdep warns of a potential lock inversion, i2s->lock is held numerous
times whilst we are under the substream lock (snd_pcm_stream_lock). If
we use the IRQ unsafe spin lock calls, you can also end up locking
snd_pcm_stream_lock whilst under i2s->lock (if an IRQ happens whilst we
are holding i2s->lock). This could result in deadlock.

[   18.147001]        CPU0                    CPU1
[   18.151509]        ----                    ----
[   18.156022]   lock(&(&pri_dai->spinlock)->rlock);
[   18.160701]                                local_irq_disable();
[   18.166622]                                lock(&(&substream->self_group.lock)->rlock);
[   18.174595]                                lock(&(&pri_dai->spinlock)->rlock);
[   18.181806]   <Interrupt>
[   18.184408]     lock(&(&substream->self_group.lock)->rlock);
[   18.190045]
[   18.190045]  *** DEADLOCK ***

This patch changes to using the irq safe spinlock calls, to avoid this
issue.

Fixes: ce8bcdbb ("ASoC: samsung: i2s: Protect more registers with a spinlock")
Signed-off-by: default avatarCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: default avatarAnand Moon <linux.amoon@gmail.com>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      a7b55a4f
    • Alexandra Yates's avatar
      Adding Intel Lewisburg device IDs for SATA · 40744375
      Alexandra Yates authored 
      commit f5bdd66c upstream.

This patch complements the list of device IDs previously
added for lewisburg sata.
Signed-off-by: default avatarAlexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: default avatarTejun Heo <tj@kernel.org>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      40744375
    • Alexandra Yates's avatar
      ahci: Order SATA device IDs for codename Lewisburg · 4ffb3cd7
      Alexandra Yates authored 
      commit 4d92f009 upstream.

This change was to preserve the ascending order of device IDs.
There was an exception with the first two Lewisburg device IDs to
keep all device IDs of the same kind grouped by code name.
Signed-off-by: default avatarAlexandra Yates <alexandra.yates@linux.intel.com>
signed-off-by: default avatarTejun Heo <tj@kernel.org>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      4ffb3cd7
    • Alexandra Yates's avatar
      ahci: add new Intel device IDs · 3c685947
      Alexandra Yates authored 
      commit 56e74338 upstream.

Adding Intel codename Lewisburg platform device IDs for SATA.
Signed-off-by: default avatarAlexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: default avatarTejun Heo <tj@kernel.org>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      3c685947
    • Hans Verkuil's avatar
      [media] adv7604: fix tx 5v detect regression · 4c18503e
      Hans Verkuil authored 
      commit 0ba4581c upstream.

The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: default avatarHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      4c18503e
    • Liad Kaufman's avatar
      iwlwifi: mvm: inc pending frames counter also when txing non-sta · 1ddea5ad
      Liad Kaufman authored 
      commit fb896c44 upstream.

Until this patch, when TXing non-sta the pending_frames counter
wasn't increased, but it WAS decreased in
iwl_mvm_rx_tx_cmd_single(), what makes it negative in certain
conditions. This in turn caused much trouble when we need to
remove the station since we won't be waiting forever until
pending_frames gets 0. In certain cases, we were exhausting
the station table even in BSS mode, because we had a lot of
stale stations.

Increase the counter also in iwl_mvm_tx_skb_non_sta() after a
successful TX to avoid this outcome.
Signed-off-by: default avatarLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: default avatarEmmanuel Grumbach <emmanuel.grumbach@intel.com>
[ kamal: backport to 4.2: file rename ]
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      1ddea5ad
    • Arnd Bergmann's avatar
      libata: fix HDIO_GET_32BIT ioctl · 07222ab6
      Arnd Bergmann authored 
      commit 287e6611 upstream.

As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.

I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.

The problems with this are:

* On big-endian machines, this will always write a zero because it
  stores the wrong byte into user space.

* In compat mode, the upper three bytes of the variable are updated
  by the compat_hdio_ioctl() function, but they now contain
  uninitialized stack data.

* The hdparm tool calling this ioctl uses a 'static long' variable
  to store the result. This means at least the upper bytes are
  initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
  would fill them with data that remains stale when the low byte
  is overwritten. Fortunately libata doesn't implement any of the
  affected ioctl commands, so this would only happen when we query
  both an IDE and an ATA device in the same command such as
  "hdparm -N -c /dev/hda /dev/sda"

* The libata code for unknown reasons started using ATA_IOC_GET_IO32
  and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
  while the ioctl commands that were added later use the normal
  HDIO_* names. This is harmless but rather confusing.

This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
Reported-by: default avatarSoohoon Lee <Soohoon.Lee@f5.com>
Tested-by: default avatarSoohoon Lee <Soohoon.Lee@f5.com>
Signed-off-by: default avatarTejun Heo <tj@kernel.org>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      07222ab6
    • Sven Eckelmann's avatar
      mac80211: minstrel: Change expected throughput unit back to Kbps · ec88457e
      Sven Eckelmann authored 
      commit 212c5a5e upstream.

The change from cur_tp to the function
minstrel_get_tp_avg/minstrel_ht_get_tp_avg changed the unit used for the
current throughput. For example in minstrel_ht the correct
conversion between them would be:

    mrs->cur_tp / 10 == minstrel_ht_get_tp_avg(..).

This factor 10 must also be included in the calculation of
minstrel_get_expected_throughput and minstrel_ht_get_expected_throughput to
return values with the unit [Kbps] instead of [10Kbps]. Otherwise routing
algorithms like B.A.T.M.A.N. V will make incorrect decision based on these
values. Its kernel based implementation expects expected_throughput always
to have the unit [Kbps] and not sometimes [10Kbps] and sometimes [Kbps].

The same requirement has iw or olsrdv2's nl80211 based statistics module
which retrieve the same data via NL80211_STA_INFO_TX_BITRATE.

Fixes: 6a27b2c4 ("mac80211: restructure per-rate throughput calculation into function")
Signed-off-by: default avatarSven Eckelmann <sven@open-mesh.com>
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      ec88457e
    • Chris Bainbridge's avatar
      mac80211: fix use of uninitialised values in RX aggregation · 2011b7d1
      Chris Bainbridge authored 
      commit f39ea269 upstream.

Use kzalloc instead of kmalloc for struct tid_ampdu_rx to
initialize the "removed" field (all others are initialized
manually). That fixes:

UBSAN: Undefined behaviour in net/mac80211/rx.c:932:29
load of value 2 is not a valid value for type '_Bool'
CPU: 3 PID: 1134 Comm: kworker/u16:7 Not tainted 4.5.0-rc1+ #265
Workqueue: phy0 rt2x00usb_work_rxdone
 0000000000000004 ffff880254a7ba50 ffffffff8181d866 0000000000000007
 ffff880254a7ba78 ffff880254a7ba68 ffffffff8188422d ffffffff8379b500
 ffff880254a7bab8 ffffffff81884747 0000000000000202 0000000348620032
Call Trace:
 [<ffffffff8181d866>] dump_stack+0x45/0x5f
 [<ffffffff8188422d>] ubsan_epilogue+0xd/0x40
 [<ffffffff81884747>] __ubsan_handle_load_invalid_value+0x67/0x70
 [<ffffffff82227b4d>] ieee80211_sta_reorder_release.isra.16+0x5ed/0x730
 [<ffffffff8222ca14>] ieee80211_prepare_and_rx_handle+0xd04/0x1c00
 [<ffffffff8222db03>] __ieee80211_rx_handle_packet+0x1f3/0x750
 [<ffffffff8222e4a7>] ieee80211_rx_napi+0x447/0x990

While at it, convert to use sizeof(*tid_agg_rx) instead.

Fixes: 788211d8 ("mac80211: fix RX A-MPDU session reorder timer deletion")
Signed-off-by: default avatarChris Bainbridge <chris.bainbridge@gmail.com>
[reword commit message, use sizeof(*tid_agg_rx)]
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      2011b7d1
    • Johannes Berg's avatar
      cfg80211/wext: fix message ordering · 11eee1c3
      Johannes Berg authored 
      commit cb150b9d upstream.

Since cfg80211 frequently takes actions from its netdev notifier
call, wireless extensions messages could still be ordered badly
since the wext netdev notifier, since wext is built into the
kernel, runs before the cfg80211 netdev notifier. For example,
the following can happen:

5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
    link/ether

when setting the interface down causes the wext message.

To also fix this, export the wireless_nlevent_flush() function
and also call it from the cfg80211 notifier.
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      11eee1c3
    • Johannes Berg's avatar
      wext: fix message delay/ordering · e5f07718
      Johannes Berg authored 
      commit 8bf86273 upstream.

Beniamino reported that he was getting an RTM_NEWLINK message for a
given interface, after the RTM_DELLINK for it. It turns out that the
message is a wireless extensions message, which was sent because the
interface had been connected and disconnection while it was deleted
caused a wext message.

For its netlink messages, wext uses RTM_NEWLINK, but the message is
without all the regular rtnetlink attributes, so "ip monitor link"
prints just rudimentary information:

5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
    link/ether
(from my hwsim reproduction)

This can cause userspace to get confused since it doesn't expect an
RTM_NEWLINK message after RTM_DELLINK.

The reason for this is that wext schedules a worker to send out the
messages, and the scheduling delay can cause the messages to get out
to userspace in different order.

To fix this, have wext register a netdevice notifier and flush out
any pending messages when netdevice state changes. This fixes any
ordering whenever the original message wasn't sent by a notifier
itself.
Reported-by: default avatarBeniamino Galvani <bgalvani@redhat.com>
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      e5f07718
    • Vladis Dronov's avatar
      Input: aiptek - fix crash on detecting device without endpoints · 6d286755
      Vladis Dronov authored 
      commit 8e20cf2b upstream.

The aiptek driver crashes in aiptek_probe() when a specially crafted USB
device without endpoints is detected. This fix adds a check that the device
has proper configuration expected by the driver. Also an error return value
is changed to more matching one in one of the error paths.
Reported-by: default avatarRalf Spenneberg <ralf@spenneberg.net>
Signed-off-by: default avatarVladis Dronov <vdronov@redhat.com>
Signed-off-by: default avatarDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      6d286755
    • Martin Schwidefsky's avatar
      s390/mm: four page table levels vs. fork · 5b62f74b
      Martin Schwidefsky authored 
      commit 3446c13b upstream.

The fork of a process with four page table levels is broken since
git commit 6252d702 "[S390] dynamic page tables."

All new mm contexts are created with three page table levels and
an asce limit of 4TB. If the parent has four levels dup_mmap will
add vmas to the new context which are outside of the asce limit.
The subsequent call to copy_page_range will walk the three level
page table structure of the new process with non-zero pgd and pud
indexes. This leads to memory clobbers as the pgd_index *and* the
pud_index is added to the mm->pgd pointer without a pgd_deref
in between.

The init_new_context() function is selecting the number of page
table levels for a new context. The function is used by mm_init()
which in turn is called by dup_mm() and mm_alloc(). These two are
used by fork() and exec(). The init_new_context() function can
distinguish the two cases by looking at mm->context.asce_limit,
for fork() the mm struct has been copied and the number of page
table levels may not change. For exec() the mm_alloc() function
set the new mm structure to zero, in this case a three-level page
table is created as the temporary stack space is located at
STACK_TOP_MAX = 4TB.

This fixes CVE-2016-2143.
Reported-by: default avatarMarcin Kościelnicki <koriakin@0x04.net>
Reviewed-by: default avatarHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: default avatarMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: default avatarKamal Mostafa <kamal@canonical.com>
      5b62f74b
  3. 10 Mar, 2016 18 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7