- 12 Feb, 2024 3 commits
-
-
Hans de Goede authored
The MeeGoPad T8 uses the standard rt5645 jd_mode=3 setting for jack-detect, but the used jack connector outputs an inverted jack-detect signal. Add a DMI quirk for this. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Link: https://msgid.link/r/20240211212736.179605-2-hdegoede@redhat.comSigned-off-by:
Mark Brown <broonie@kernel.org>
-
Hans de Goede authored
The DMI strings used for the LattePanda board DMI quirks are very generic. Using the dmidecode database from https://linux-hardware.org/ shows that the chosen DMI strings also match the following 2 laptops which also have a rt5645 codec: Insignia NS-P11W7100 https://linux-hardware.org/?computer=E092FFF8BA04 Insignia NS-P10W8100 https://linux-hardware.org/?computer=AFB6C0BF7934 All 4 hw revisions of the LattePanda board have "S70CR" in their BIOS version DMI strings: DF-BI-7-S70CR100-* DF-BI-7-S70CR110-* DF-BI-7-S70CR200-* LP-BS-7-S70CR700-* See e.g. https://linux-hardware.org/?computer=D98250A817C0 Add a partial (non exact) DMI match on this string to make the LattePanda board DMI match more precise to avoid false-positive matches. Signed-off-by:
-
Mark Brown authored
Merge series from Hans de Goede <hdegoede@redhat.com>: While testing 6.8 on a Bay Trail device with a ALC5640 codec I noticed a regression in 6.8 which causes a NULL pointer deref in probe(). All BYT/CHT Intel machine drivers are affected. Patch 1/2 of this series fixes all of them. Patch 2/2 adds some small cleanups to cht_bsw_rt5645.c for issues which I noticed while working on 1/2.
-
- 11 Feb, 2024 4 commits
-
-
Cristian Ciocaltea authored
A recent change in acp_irq_thread() was meant to address a potential race condition while trying to acquire the hardware semaphore responsible for the synchronization between firmware and host IPC interrupts. This resulted in an improper use of the IPC spinlock, causing normal kernel memory allocations (which may sleep) inside atomic contexts: 1707255557.133976 kernel: BUG: sleeping function called from invalid context at include/linux/sched/mm.h:315 ... 1707255557.134757 kernel: sof_ipc3_rx_msg+0x70/0x130 [snd_sof] 1707255557.134793 kernel: acp_sof_ipc_irq_thread+0x1e0/0x550 [snd_sof_amd_acp] 1707255557.134855 kernel: acp_irq_thread+0xa3/0x130 [snd_sof_amd_acp] 1707255557.134904 kernel: ? irq_thread+0xb5/0x1e0 1707255557.134947 kernel: ? __pfx_irq_thread_fn+0x10/0x10 1707255557.134985 kernel: irq_thread_fn+0x23/0x60 Moreover, there are attempts to lock a mutex from the same atomic context: 1707255557.136357 kernel: ============================= 1707255557.136393 kernel: [ BUG: Invalid wait context ] 1707255557.136413 kernel: 6.8.0-rc3-next-20240206-audio-next #9 Tainted: G W 1707255557.136432 kernel: ----------------------------- 1707255557.136451 kernel: irq/66-AudioDSP/502 is trying to lock: 1707255557.136470 kernel: ffff965152f26af8 (&sb->s_type->i_mutex_key#2){+.+.}-{3:3}, at: start_creating.part.0+0x5f/0x180 ... 1707255557.137429 kernel: start_creating.part.0+0x5f/0x180 1707255557.137457 kernel: __debugfs_create_file+0x61/0x210 1707255557.137475 kernel: snd_sof_debugfs_io_item+0x75/0xc0 [snd_sof] 1707255557.137494 kernel: sof_ipc3_do_rx_work+0x7cf/0x9f0 [snd_sof] 1707255557.137513 kernel: sof_ipc3_rx_msg+0xb3/0x130 [snd_sof] 1707255557.137532 kernel: acp_sof_ipc_irq_thread+0x1e0/0x550 [snd_sof_amd_acp] 1707255557.137551 kernel: acp_irq_thread+0xa3/0x130 [snd_sof_amd_acp] Fix the issues by reducing the lock scope in acp_irq_thread(), so that it guards only the hardware semaphore acquiring attempt. Additionally, restore the initial locking in acp_sof_ipc_irq_thread() to synchronize the handling of immediate replies from DSP core. Fixes: 802134c8 ("ASoC: SOF: amd: Refactor spinlock_irq(&sdev->ipc_lock) sequence in irq_handler") Signed-off-by:Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Link: https://lore.kernel.org/r/20240208234315.2182048-1-cristian.ciocaltea@collabora.comSigned-off-by:
-
Alexey Khoroshilov authored
There is a path in rt5645_jack_detect_work(), where rt5645->jd_mutex is left locked forever. That may lead to deadlock when rt5645_jack_detect_work() is called for the second time. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: cdba4301 ("ASoC: rt5650: add mutex to avoid the jack detection failure") Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Link: https://lore.kernel.org/r/1707645514-21196-1-git-send-email-khoroshilov@ispras.ruSigned-off-by:
-
Hans de Goede authored
4 fixes / cleanups to the rt5645 mc driver's codec_name handling: 1. In the for loop looking for the dai_index for the codec, replace card->dai_link[i] with cht_dailink[i]. The for loop already uses ARRAY_SIZE(cht_dailink) as bound and card->dai_link is just a pointer to cht_dailink using card->dai_link only obfuscates that cht_dailink is being modified directly rather then say a copy of cht_dailink. Using cht_dailink[i] also makes the code consistent with other machine drivers. 2. Don't set cht_dailink[dai_index].codecs->name in the for loop, this immediately gets overridden using acpi_dev_name(adev) directly below the loop. 3. Add a missing break to the loop. 4. Remove the now no longer used (only set, never read) codec_name field from struct cht_mc_private. Signed-off-by:
-
Hans de Goede authored
Since commit 13f58267 ("ASoC: soc.h: don't create dummy Component via COMP_DUMMY()") dummy snd_soc_dai_link.codecs entries no longer have a name set. This means that when looking for the codec dai_link the machine driver can no longer unconditionally run strcmp() on snd_soc_dai_link.codecs[0].name since this may now be NULL. Add a check for snd_soc_dai_link.codecs[0].name being NULL to all BYT/CHT machine drivers to avoid NULL pointer dereferences in their probe() methods. Fixes: 13f58267 ("ASoC: soc.h: don't create dummy Component via COMP_DUMMY()") Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
- 09 Feb, 2024 1 commit
-
-
Richard Fitzgerald authored
The driver never uses the IRQ1_CFG register so there's no need to provide a default value. It's set as a readable register only for debugging through the regmap registers file. A system-specific firmware could overwrite this register with a non-default value. Therefore the driver can't hardcode what the initial value actually is. As the register is only for debugging the value can be left unknown until someone wants to read it through debugfs. Signed-off-by:
Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20240209145700.1555950-1-rf@opensource.cirrus.comSigned-off-by:
-
- 08 Feb, 2024 2 commits
-
-
Ranjani Sridharan authored
With the change in the widget free logic to power down the cores only when the scheduler widgets are freed, we need to ensure that the scheduler widget is freed only after all the widgets associated with the scheduler are freed. This is to ensure that the secondary core that the scheduler is scheduled to run on is kept powered on until all widgets that need them are in use. While this works well for dynamic pipelines, in the case of static pipelines the current logic does not take this into account and frees all widgets in the order they occur in the widget_list. So, modify this to ensure that the scheduler widgets are freed only after all other types of widgets in the widget_list are freed. Link: https://github.com/thesofproject/linux/issues/4807 Fixes: 31ed8da1 ("ASoC: SOF: sof-audio: Modify logic for enabling/disabling topology cores") Signed-off-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by:
Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by:
-
Richard Fitzgerald authored
Rewrite the handling of ASP1 TX mixer mux initialization to prevent a deadlock during component_remove(). The firmware can overwrite the ASP1 TX mixer registers with system-specific settings. This is mainly for hardware that uses the ASP as a chip-to-chip link controlled by the firmware. Because of this the driver cannot know the starting state of the ASP1 mixer muxes until the firmware has been downloaded and rebooted. The original workaround for this was to queue a work function from the dsp_work() job. This work then read the register values (populating the regmap cache the first time around) and then called snd_soc_dapm_mux_update_power(). The problem with this is that it was ultimately triggered by cs35l56_component_probe() queueing dsp_work, which meant that it would be running in parallel with the rest of the ASoC component and card initialization. To prevent accessing DAPM before it was fully initialized the work function took the card mutex. But this would deadlock if cs35l56_component_remove() was called before the work job had completed, because ASoC calls component_remove() with the card mutex held. This new version removes the work function. Instead the regmap cache and DAPM mux widgets are initialized the first time any of the associated ALSA controls is read or written. Signed-off-by:
-
- 07 Feb, 2024 3 commits
-
-
Amadeusz Sławiński authored
In case TDM is set in topology on SSP0, parser will overwrite vindex value, because it only checks if port is set. Fix this by checking whole field value. Fixes: e6d50e47 ("ASoC: Intel: avs: Improve topology parsing of dynamic strings") Reviewed-by:
Cezary Rojewski <cezary.rojewski@intel.com> Signed-off-by:
Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Link: https://lore.kernel.org/r/20240207112624.2132821-1-amadeuszx.slawinski@linux.intel.comSigned-off-by:
-
Charles Keepax authored
The IRQ should be disabled whilst entering and exiting system suspend to avoid the IRQ handler being called whilst the PM runtime is disabled. Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20240206113850.719888-2-ckeepax@opensource.cirrus.comSigned-off-by:
-
Charles Keepax authored
As devm_pm_runtime_enable can fail due to memory allocations, it is best to handle the error. Signed-off-by:
-
- 06 Feb, 2024 1 commit
-
-
Mario Limonciello authored
The laptop requires a quirk ID to enable its internal microphone. Add it to the DMI quirk table. Reported-by:
Stanislav Petrov <stanislav.i.petrov@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216925 Cc: stable@vger.kernel.org Signed-off-by:
Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20240205214853.2689-1-mario.limonciello@amd.comSigned-off-by:
-
- 05 Feb, 2024 4 commits
-
-
Gergo Koteles authored
The tascodec_init() of the snd-soc-tas2781-comlib module is called from snd-soc-tas2781-i2c and snd-hda-scodec-tas2781-i2c modules. It calls request_firmware_nowait() with parameter THIS_MODULE and a cont/callback from the latter modules. The latter modules can be removed while their callbacks are running, resulting in a general protection failure. Add module parameter to tascodec_init() so request_firmware_nowait() can be called with the module of the callback. Fixes: ef3bcde7 ("ASoC: tas2781: Add tas2781 driver") CC: stable@vger.kernel.org Signed-off-by:
Gergo Koteles <soyer@irl.hu> Link: https://lore.kernel.org/r/118dad922cef50525e5aab09badef2fa0eb796e5.1707076603.git.soyer@irl.huSigned-off-by:
-
Cezary Rojewski authored
Recent changes modified operation-order in the probe() function without updating its error path accordingly. If snd_hdac_i915_init() exists with status EPROBE_DEFER the error path must cleanup allocated IRQs before leaving the scope. Fixes: 2dddc514 ("ASoC: Intel: avs: Move snd_hdac_i915_init to before probe_work.") Signed-off-by:
-
Jeffrey Hugo authored
The servers for the @codeaurora domain have long been retired and any messages sent there bounce. Srinivasa Rao Mandadapu has left the company and there does not appear to be an updated address to suggest, so drop Srinivasa as maintainer of the binding. The binding still appears to be maintined as Judy is listed. Signed-off-by:
Jeffrey Hugo <quic_jhugo@quicinc.com> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240202174313.4113670-1-quic_jhugo@quicinc.comSigned-off-by:
-
Dan Carpenter authored
It looks like the "!" character was added accidentally. The regmap_update_bits_check() function is normally going to succeed. This means the rest of the function is unreachable and we don't handle the situation where "changed" is true correctly. Fixes: 07f7d6e7 ("ASoC: cs35l56: Fix for initializing ASP1 mixer registers") Signed-off-by:
Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by:
-
- 01 Feb, 2024 19 commits
-
-
Mark Brown authored
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>: These patches fixe various things that were undocumented, unknown or uncertain when the original driver code was written. And also a few things that were just bugs.
-
Richard Fitzgerald authored
Remove an unused stub function that calls a non-existant function. This function was accidentally added as part of commit 2144833e ("ALSA: hda: cirrus_scodec: Add KUnit test"). It was a relic of an earlier version of the test that should have been removed. Signed-off-by:
-
Richard Fitzgerald authored
Check whether the firmware is already patched. If so, include the firmware version in the firmware file name. If the firmware has already been patched by the BIOS the driver can only replace it if it has control of hard RESET. If the driver cannot replace the firmware, it can still load a wmfw (for ALSA control definitions) and/or a bin (for additional tunings). But these must match the version of firmware that is running on the CS35L56. The firmware is pre-patched if either: - FIRMWARE_MISSING == 0, or - it is a secured CS35L56 (which implies that is was already patched), cs35l56_hw_init() will set preloaded_fw_ver to the (non-zero) firmware version if either of these conditions is true. Normal (unpatched or replaceable firmware): cs35l56-rev-dsp1-misc[-system_name].[wmfw|bin] Preloaded firmware: cs35l56-rev[-s]-VVVVVV-dsp1-misc[-system_name].[wmfw|bin] Where: [-s] is an optional -s added into the name for a secured CS35L56 VVVVVV is the 24-bit firmware version in hexadecimal. Backport note: This won't apply to kernel versions older than v6.6. Signed-off-by:
-
Richard Fitzgerald authored
Change the filename field layout to: cs35l56-rev[-s]-dsp1-misc[-sub].[wmfw|bin] This is to keep the same firmware file naming scheme as the CS35L56 ASoC driver. This is not a compatibility break because no firmware files have been published. The original field layout matched the ASoC driver, but the way the ASoC driver used the wm_adsp driver config to form this filename was bugged. Fixing the ASoC driver to use the correct wm_adsp config strings means that the 's' flag (to indicate a secured part) has to move to somewhere after the first '-'. Signed-off-by:
-
Richard Fitzgerald authored
Check for the cases of system-specific bin file without a wmfw before falling back to looking for a generic wmfw. All system-specific options should be tried before falling back to loading a generic wmfw/bin. With the original code, the presence of a fallback generic wmfw on the filesystem would prevent using a system-specific tuning with a ROM firmware. Signed-off-by:
-
Richard Fitzgerald authored
The original 50ms timeout for firmware boot is not long enough for worst-case time to reboot after a firmware download. Increase the timeout to 250ms. Signed-off-by:
-
Richard Fitzgerald authored
If the "spk-id-gpios" property is present it points to GPIOs whose value must be used to select the correct bin file to match the speakers. Some manufacturers use multiple sources of speakers, which need different tunings for best performance. On these models the type of speaker fitted is indicated by the values of one or more GPIOs. The number formed by the GPIOs identifies the tuning required. The speaker ID must be used in combination with the subsystem ID (either from PCI SSID or cirrus,firmware-uid property), because the GPIOs can only indicate variants of a specific model. Signed-off-by:
-
Richard Fitzgerald authored
Check during initialization whether the firmware is already patched. If so, include the firmware version in the wm_adsp fwf_name string. If the firmware has already been patched by the BIOS the driver can only replace it if it has control of hard RESET. If the driver cannot replace the firmware, it can still load a wmfw (for ALSA control definitions) and/or a bin (for additional tunings). But these must match the version of firmware that is running on the CS35L56. The firmware is pre-patched if FIRMWARE_MISSING == 0. Including the firmware version in the fwf_name string will qualify the firmware file name: Normal (unpatched or replaceable firmware): cs35l56-rev-dsp1-misc[-system_name].[wmfw|bin] Preloaded firmware: cs35l56-rev[-s]-VVVVVV-dsp1-misc[-system_name].[wmfw|bin] Where: [-s] is an optional -s added into the name for a secured CS35L56 VVVVVV is the 24-bit firmware version in hexadecimal. Signed-off-by:
-
Richard Fitzgerald authored
Put the silicon revision and secured flag in the wm_adsp fwf_name string instead of including them in the part string. This changes the format of the firmware name string from cs35l56[s]-rev-misc[-system_name] to cs35l56-rev[-s]-misc[-system_name] No firmware files have been published, so this doesn't cause a compatibility break. Silicon revision and secured flag are included in the firmware filename to pick a firmware compatible with the part. These strings were being added to the part string, but that is a misuse of the string. The correct place for these is the fwf_name string, which is specifically intended to select between multiple firmware files for the same part. Backport note: This won't apply to kernels older than v6.6. Signed-off-by:
-
Richard Fitzgerald authored
Defer initializing the state of the ASP1 mixer registers until the firmware has been downloaded and rebooted. On a SoundWire system the ASP is free for use as a chip-to-chip interconnect. This can be either for the firmware on multiple CS35L56 to share reference audio; or as a bridge to another device. If it is a firmware interconnect it is owned by the firmware and the Linux driver should avoid writing the registers. However, if it is a bridge then Linux may take over and handle it as a normal codec-to-codec link. Even if the ASP is used as a firmware-firmware interconnect it is useful to have ALSA controls for the ASP mixer. They are at least useful for debugging. CS35L56 is designed for SDCA and a generic SDCA driver would know nothing about these chip-specific registers. So if the ASP is being used on a SoundWire system the firmware sets up the ASP mixer registers. This means that we can't assume the default state of these registers. But we don't know the initial state that the firmware set them to until after the firmware has been downloaded and booted, which can take several seconds when downloading multiple amps. DAPM normally reads the initial state of mux registers during probe() but this would mean blocking probe() for several seconds until the firmware has initialized them. To avoid this, the mixer muxes are set SND_SOC_NOPM to prevent DAPM trying to read the register state. Custom get/set callbacks are implemented for ALSA control access, and these can safely block waiting for the firmware download. After the firmware download has completed, the state of the mux registers is known so a work job is queued to call snd_soc_dapm_mux_update_power() on each of the mux widgets. Backport note: This won't apply cleanly to kernels older than v6.6. Signed-off-by:
-
Richard Fitzgerald authored
Add ASP1_FRAME_CONTROL1, ASP1_FRAME_CONTROL5 and the ASP1_TX?_INPUT registers to the sequence used to initialize the ASP configuration. Write this sequence to the cache and directly to the registers to ensure that they match. A system-specific firmware can patch these registers to values that are not the silicon default, so that the CS35L56 boots already in the configuration used by Windows or by "driverless" Windows setups such as factory tuning. These may not match how Linux is configuring the HDA codec. And anyway on Linux the ALSA controls are used to configure routing options. Signed-off-by:
-
Richard Fitzgerald authored
Patch the SDW TX mixer registers to silicon defaults. CS35L56 is designed for SDCA and a generic SDCA driver would know nothing about these chip-specific registers. So the firmware sets up the SDW TX mixer registers to whatever audio is relevant on a specific system. This means that the driver cannot assume the initial values of these registers. But Linux has ALSA controls to configure routing, so the registers can be patched to silicon default and the ALSA controls used to select what audio to feed back to the host capture path. Backport note: This won't apply to kernels older than v6.6. Signed-off-by:
-
Richard Fitzgerald authored
Add a dummy SUPPLY widget connected to the ASP that forces the chip registers to match the regmap cache when the ASP is powered-up. On a SoundWire system the ASP is free for use as a chip-to-chip interconnect. This can be either for the firmware on multiple CS35L56 to share reference audio; or as a bridge to another device. If it is a firmware interconnect it is owned by the firmware and the Linux driver should avoid writing the registers. However. If it is a bridge then Linux may take over and handle it as a normal codec-to-codec link. CS35L56 is designed for SDCA and a generic SDCA driver would know nothing about these chip-specific registers. So if the ASP is being used on a SoundWire system the firmware sets up the ASP registers. This means that we can't assume the default state of the ASP registers. But we don't know the initial state that the firmware set them to until after the firmware has been downloaded and booted, which can take several seconds when downloading multiple amps. To avoid blocking probe() for several seconds waiting for the firmware, the silicon defaults are assumed. This allows the machine driver to setup the ASP configuration during probe() without being blocked. If the ASP is hooked up and used, the SUPPLY widget ensures that the chip registers match what was configured in the regmap cache. If the machine driver does not hook up the ASP, it is assumed that it won't call any functions to configure the ASP DAI. Therefore the regmap cache will be clean for these registers so a regcache_sync() will not overwrite the chip registers. If the DAI is not hooked up, the dummy SUPPLY widget will not be invoked so it will never force-overwrite the chip registers. Backport note: This won't apply cleanly to kernels older than v6.6. Signed-off-by:
-
Richard Fitzgerald authored
Remove the check of fw_patched from cs35l56_is_fw_reload_needed(). Also remove the redundant check for control of the reset GPIO. The fw_patched flag is set when cs35l56_dsp_work() has completed its steps to download firmware and power-up wm_adsp. There was a check in cs35l56_is_fw_reload_needed() to make a quick exit of 'false' if !fw_patched. The original idea was that the system might be suspended before the driver has ever made any attempt to download firmware, and in that case the driver doesn't need to return to a patched state because it was never in a patched state. This check of fw_patched is buggy because it prevented ever recovering from a failed patch. If a previous attempt to patch and reboot the silicon had failed it would leave fw_patched==false. This would mean the driver never attempted another download even though the fault may have been cleared (by a hard reset, for example). It is also a redundant check because the calling code already makes a quick exit if cs35l56_component_probe() has not been called, which deals with the original intent of this check but in a safer way. The check for reset GPIO is redundant: if the silicon was hard-reset the FIRMWARE_MISSING flag will be 1. But this check created an expectation that the suspend/resume code toggles reset. This can't easily be protected against accidental code breakage. The only reason for the check was to skip runtime-resuming the driver to read the PROTECTION_STATUS register when it already knows it reset the silicon. But in that case the driver will have to be runtime-resumed to do the firmware download. So it created an assumption for no benefit. Signed-off-by:
-
Richard Fitzgerald authored
Move the call to cs35l56_set_patch() earlier in cs35l56_init() so that it only adds the register patch on first-time initialization. The call was after the post_soft_reset label, so every time this function was run to re-initialize the hardware after a reset it would call regmap_register_patch() and add the same reg_sequence again. Signed-off-by:
-
Richard Fitzgerald authored
cs35l56_component_remove() must call wm_adsp_power_down() and wm_adsp2_component_remove(). Signed-off-by:
-
Richard Fitzgerald authored
The cs35l56->component pointer is used by the suspend-resume handling to know whether the driver is fully instantiated. This is to prevent it queuing dsp_work which would result in calling wm_adsp when the driver is not an instantiated ASoC component. So this pointer must be cleared by cs35l56_component_remove(). Signed-off-by:
-
Richard Fitzgerald authored
There's no need to overwrite fwf_name with a kstrdup() of the cs_dsp part name. It is trivial to select either fwf_name or cs_dsp.part as the string to use when building the filename in wm_adsp_request_firmware_file(). This leaves fwf_name entirely owned by the codec driver. It also avoids problems with freeing the pointer. With the original code fwf_name was either a pointer owned by the codec driver, or a kstrdup() created by wm_adsp. This meant wm_adsp must free it if it set it, but not if the codec driver set it. The code was handling this by using devm_kstrdup(). But there is no absolute requirement that wm_adsp_common_init() must be called from probe(), so this was a pseudo-memory leak - each new call to wm_adsp_common_init() would allocate another block of memory but these would only be freed if the owning codec driver was removed. Signed-off-by:
-
Richard Fitzgerald authored
Check for the cases of system-specific bin file without a wmfw before falling back to looking for a generic wmfw. All system-specific options should be tried before falling back to loading a generic wmfw/bin. With the original code, the presence of a fallback generic wmfw on the filesystem would prevent using a system-specific tuning with a ROM firmware. Signed-off-by:
-
- 29 Jan, 2024 3 commits
-
-
Marian Postevca authored
Previous commit that added support for Huawei MateBook D16 2021 with Ryzen 4600H (HVY-WXX9 M1010) was incomplete. To activate support for this laptop, the DMI table in acp3x-es83xx machine driver must also be updated. Fixes: b5338b1b ("ASoC: amd: acp: Add support for a new Huawei Matebook laptop") Signed-off-by:
Marian Postevca <posteuca@mutex.one> Link: https://msgid.link/r/20240128172229.657142-1-posteuca@mutex.oneSigned-off-by:
-
Mark Brown authored
Merge series from Chen-Yu Tsai <wens@kernel.org>: This series adds SPDIF controllers for the H616 and H618. There's also a fix for SPDIF on H6: the controller also has a receiver that was not correctly modeled.
-
Chen-Yu Tsai authored
The SPDIF hardware block found in the H616 SoC has the same layout as the one found in the H6 SoC, except that it is missing the receiver side. Add a new compatible string for it. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Acked-by:
Conor Dooley <conor.dooley@microchip.com> Reviewed-by:
Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://msgid.link/r/20240127163247.384439-3-wens@kernel.orgSigned-off-by:
-
