- 27 Jan, 2006 12 commits
-
-
Tejun Heo authored
AHCI spec mandates engine to be stopped during hard resets. Signed-off-by:
Tejun Heo <htejun@gmail.com> Signed-off-by:
Jeff Garzik <jgarzik@pobox.com>
-
Tejun Heo authored
Wrap pio/atapi task queueing in correspondingly named functions. This change doesn't change anything. It's preparation for follow-up pio-task/eh sync patch. Signed-off-by:
-
Tejun Heo authored
Implement ata_eh_qc_complete/retry() using scsi_eh_finish_cmd() and scsi_eh_flush_done_q(). This removes all eh scsicmd finish hacks from low level drivers. This change was first suggested by Jeff Garzik. Signed-off-by:
-
Tejun Heo authored
Export two SCSI EH command handling functions. To be used by libata EH. Signed-off-by:
-
Tejun Heo authored
Return AC_ERR_* mask from issue fuctions instead of 0/-1. This enables things like failing a qc with AC_ERR_HSM when the device doesn't set DRDY when the qc is about to be issued. Signed-off-by:
-
Tejun Heo authored
Add detailed AC_ERR_* flags and use them. Long-term goal is to describe all errors with err_mask and tf combination (tf for failed sector information, etc...). After proper error diagnosis is implemented, sense data should also be generated from err_mask instead of directly from hardware tf registers as it is currently. Signed-off-by:
-
Tejun Heo authored
In ahci_host_intr err_mask is determined from IRQ status but never used. This patch sets qc->err_mask to the determined err_mask. Signed-off-by:
-
Tejun Heo authored
When ata_qc_issue() fails, the qc might have been dma mapped or not. So, performing only ata_qc_free() results in dma map leak. This patch makes ata_qc_issue() mark dma map flags correctly on failure and calls ata_qc_complete() after ata_qc_issue() fails. Signed-off-by:
-
Tejun Heo authored
qc used to be freed automatically on command completion. However, as a qc can carry information about its completion status, it can be useful to its owner/issuer after command completion. This patch makes freeing qc responsibility of its owner. This simplifies ata_exec_internal() and makes command turn-around for atapi request sensing less hackish. This change was originally suggested by Jeff Garzik. Signed-off-by:
-
Tejun Heo authored
All ata_qc_free() does is calling __ata_qc_complete() which isn't used anywhere else. Fold __ata_qc_complete() into ata_qc_free(). Signed-off-by:
-
Jeff Garzik authored
-
Tejun Heo authored
Unlike their older siblings, ICH6 and 7 use different scheme for MAP VALUE. This patch makes ata_piix interpret MV properly on ICH6/7. Pre-ICH6/7 The value of these bits indicate the address range the SATA port responds to, and whether or not the SATA and IDE functions are combined. 000 = Non-combined. P0 is primary master. P1 is secondary master. 001 = Non-combined. P0 is secondary master. P1 is primary master. 100 = Combined. P0 is primary master. P1 is primary slave. P-ATA is 2:0 Map Value secondary. 101 = Combined. P0 is primary slave. P1 is primary master. P-ATA is secondary. 110 = Combined. P-ATA is primary. P0 is secondary master. P1 is secondary slave. 111 = Combined. P-ATA is primary. P0 is secondary slave. P1 is secondary master. ICH6/7 Map Value - R/W. Map Value (MV): The value in the bits below indicate the address range the SATA ports responds to, and whether or not the PATA and SATA functions are combined. When in combined mode, the AHCI memory space is not available and AHCI may not be used. 00 = Non-combined. P0 is primary master, P2 is the primary slave. P1 is secondary master, P3 is the 1:0 secondary slave (desktop only). P0 is primary master, P2 is the primary slave (mobile only). 01 = Combined. IDE is primary. P1 is secondary master, P3 is the secondary slave. (desktop only) 10 = Combined. P0 is primary master. P2 is primary slave. IDE is secondary 11 = Reserved Signed-off-by:
-
- 20 Jan, 2006 7 commits
-
-
David S. Miller authored
Signed-off-by:David S. Miller <davem@davemloft.net>
-
Linus Torvalds authored
-
Linus Torvalds authored
-
-
David S. Miller authored
The compat layer timeout handling changes in: 9f72949f are busted. This is most easily seen with an X application that uses sub-second select/poll timeout such as emacs. You hit a key and it takes a second or so before the app responds. The two ROUND_UP() calls upon entry are using {tv,ts}_sec where it should instead be using {tv_usec,ts_nsec}, which perfectly explains the observed incorrect behavior. Another bug shot down with git bisect. Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
David S. Miller authored
Or else we break on ppc32 and other 32-bit platforms. Based upon a patch from Harald Welte. Signed-off-by: -
David S. Miller authored
-
- 19 Jan, 2006 21 commits
-
-
John Hawkes authored
Fix an unnecessary softlockup watchdog warning in the ia64 uncached_build_memmap() that occurs occasionally at 256p and always at 512p. The problem occurs at boot time. Signed-off-by:
John Hawkes <hawkes@sgi.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Tony Luck <tony.luck@intel.com>
-
Jes Sorensen authored
Migrate perfmon from using an old semaphore to a completion handler. Signed-off-by:
Jes Sorensen <jes@sgi.com> Signed-off-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Jes Sorensen authored
Migrate arch/ia64/ia32/sys_ia32 to using a mutex for mmap protection. Signed-off-by:
-
David S. Miller authored
This also includes by necessity _TIF_RESTORE_SIGMASK support, which actually resulted in a lot of cleanups. The sparc signal handling code is quite a mess and I should clean it up some day. Signed-off-by: -
David S. Miller authored
Signed-off-by: -
Linus Torvalds authored
-
mark gross authored
some driver clean ups, and a re-posting of changes that are needed to match the updated TPS. Signed-off-by:
Mark Gross <mark.gross@intel.com> Signed-off-by:
-
Alan Cox authored
This is a subset of the bluesmoke project core code, stripped of the NMI work which isn't ready to merge and some of the "interesting" proc functionality that needs reworking or just has no place in kernel. It requires no core kernel changes except the added scrub functions already posted. The goal is to merge further functionality only after the core code is accepted and proven in the base kernel, and only at the point the upstream extras are really ready to merge. From: doug thompson <norsk5@xmission.com> This converts EDAC to sysfs and is the final chunk neccessary before EDAC has a stable user space API and can be considered for submission into the base kernel. Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by:
doug thompson <norsk5@xmission.com> Signed-off-by:
Pavel Machek <pavel@suse.cz> Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
EDAC requires a way to scrub memory if an ECC error is found and the chipset does not do the work automatically. That means rewriting memory locations atomically with respect to all CPUs _and_ bus masters. That means we can't use atomic_add(foo, 0) as it gets optimised for non-SMP This adds a function to include/asm-foo/atomic.h for the platforms currently supported which implements a scrub of a mapped block. It also adjusts a few other files include order where atomic.h is included before types.h as this now causes an error as atomic_scrub uses u32. Signed-off-by:
-
David Woodhouse authored
Add the sys_pselect6() and sys_poll() calls to the i386 syscall table. Signed-off-by:
David Woodhouse <dwmw2@infradead.org> Signed-off-by:
-
David Woodhouse authored
The following implementation of ppoll() and pselect() system calls depends on the architecture providing a TIF_RESTORE_SIGMASK flag in the thread_info. These system calls have to change the signal mask during their operation, and signal handlers must be invoked using the new, temporary signal mask. The old signal mask must be restored either upon successful exit from the system call, or upon returning from the invoked signal handler if the system call is interrupted. We can't simply restore the original signal mask and return to userspace, since the restored signal mask may actually block the signal which interrupted the system call. The TIF_RESTORE_SIGMASK flag deals with this by causing the syscall exit path to trap into do_signal() just as TIF_SIGPENDING does, and by causing do_signal() to use the saved signal mask instead of the current signal mask when setting up the stack frame for the signal handler -- or by causing do_signal() to simply restore the saved signal mask in the case where there is no handler to be invoked. The first patch implements the sys_pselect() and sys_ppoll() system calls, which are present only if TIF_RESTORE_SIGMASK is defined. That #ifdef should go away in time when all architectures have implemented it. The second patch implements TIF_RESTORE_SIGMASK for the PowerPC kernel (in the -mm tree), and the third patch then removes the arch-specific implementations of sys_rt_sigsuspend() and replaces them with generic versions using the same trick. The fourth and fifth patches, provided by David Howells, implement TIF_RESTORE_SIGMASK for FR-V and i386 respectively, and the sixth patch adds the syscalls to the i386 syscall table. This patch: Add the pselect() and ppoll() system calls, providing core routines usable by the original select() and poll() system calls and also the new calls (with their semantics w.r.t timeouts). Signed-off-by:
-
Jeff Dike authored
Use the generic sys_rt_sigsuspend. Signed-off-by:
Jeff Dike <jdike@addtoit.com> Signed-off-by:
-
Jeff Dike authored
Add support for TIF_RESTORE_SIGMASK. I copy the i386 handling of the flag. sys_sigsuspend is also changed to follow i386. Also a bit of cleanup - turn an if into a switch get rid of a couple more emacs formatting comments Signed-off-by:
-
David Woodhouse authored
Implement the TIF_RESTORE_SIGMASK flag in the new arch/powerpc kernel, for both 32-bit and 64-bit system call paths. Signed-off-by:
-
David Howells authored
Handle TIF_RESTORE_SIGMASK as added by David Woodhouse's patch entitled: [PATCH] 2/3 Add TIF_RESTORE_SIGMASK support for arch/powerpc [PATCH] 3/3 Generic sys_rt_sigsuspend It does the following: (1) Declares TIF_RESTORE_SIGMASK for i386. (2) Invokes it over to do_signal() when TIF_RESTORE_SIGMASK is set. (3) Makes do_signal() support TIF_RESTORE_SIGMASK, using the signal mask saved in current->saved_sigmask. (4) Discards sys_rt_sigsuspend() from the arch, using the generic one instead. (5) Makes sys_sigsuspend() save the signal mask and set TIF_RESTORE_SIGMASK rather than attempting to fudge the return registers. (6) Makes sys_sigsuspend() return -ERESTARTNOHAND rather than looping intrinsically. (7) Makes setup_frame(), setup_rt_frame() and handle_signal() return 0 or -EFAULT rather than true/false to be consistent with the rest of the kernel. Due to the fact do_signal() is then only called from one place: (8) Makes do_signal() no longer have a return value is it was just being ignored; force_sig() takes care of this. (9) Discards the old sigmask argument to do_signal() as it's no longer necessary. (10) Makes do_signal() static. (11) Marks the second argument to do_notify_resume() as unused. The unused argument should remain in the middle as the arguments are passed in as registers, and the ordering is specific in entry.S Given the way do_signal() is now no longer called from sys_{,rt_}sigsuspend(), they no longer need access to the exception frame, and so can just take arguments normally. This patch depends on sys_rt_sigsuspend patch. Signed-off-by:David Howells <dhowells@redhat.com> Signed-off-by:
-
David Howells authored
Handle TIF_RESTORE_SIGMASK as added by David Woodhouse's patch entitled: [PATCH] 2/3 Add TIF_RESTORE_SIGMASK support for arch/powerpc [PATCH] 3/3 Generic sys_rt_sigsuspend It does the following: (1) Declares TIF_RESTORE_SIGMASK for FRV. (2) Invokes it over to do_signal() when TIF_RESTORE_SIGMASK is set. (3) Makes do_signal() support TIF_RESTORE_SIGMASK, using the signal mask saved in current->saved_sigmask. (4) Discards sys_rt_sigsuspend() from the arch, using the generic one instead. (5) Makes sys_sigsuspend() save the signal mask and set TIF_RESTORE_SIGMASK rather than attempting to fudge the return registers. (6) Makes sys_sigsuspend() return -ERESTARTNOHAND rather than looping intrinsically. (7) Makes setup_frame(), setup_rt_frame() and handle_signal() return 0 or -EFAULT rather than true/false to be consistent with the rest of the kernel. Due to the fact do_signal() is then only called from one place: (8) Make do_signal() no longer have a return value is it was just being ignored; force_sig() takes care of this. (9) Discards the old sigmask argument to do_signal() as it's no longer necessary. This patch depends on the FRV signalling patches as well as the sys_rt_sigsuspend patch. Signed-off-by: -
David Woodhouse authored
The TIF_RESTORE_SIGMASK flag allows us to have a generic implementation of sys_rt_sigsuspend() instead of duplicating it for each architecture. This provides such an implementation and makes arch/powerpc use it. It also tidies up the ppc32 sys_sigsuspend() to use TIF_RESTORE_SIGMASK. Signed-off-by:
-
Ulrich Drepper authored
Wire up the x86_64 syscalls. Signed-off-by:
Ulrich Drepper <drepper@redhat.com> Signed-off-by:
-
