- 20 May, 2010 40 commits
-
-
Greg Kroah-Hartman authored
Minor whitespace cleanups to make checkpatch happy. Signed-off-by:Greg Kroah-Hartman <gregkh@suse.de>
-
Greg Kroah-Hartman authored
Minor whitespace cleanups to make checkpatch happy. Signed-off-by: -
Greg Kroah-Hartman authored
Minor whitespace cleanups to make checkpatch happy. Signed-off-by: -
Greg Kroah-Hartman authored
Minor whitespace cleanups to make checkpatch happy. Signed-off-by: -
Greg Kroah-Hartman authored
Minor whitespace cleanups to make checkpatch happy. Signed-off-by: -
Greg Kroah-Hartman authored
Minor whitespace cleanups to make checkpatch happy. Signed-off-by: -
Greg Kroah-Hartman authored
Minor whitespace cleanups to make checkpatch happy. Signed-off-by: -
Anton Vorontsov authored
Since commit 7acd72eb ("kfifo: rename kfifo_put... into kfifo_in... and kfifo_get... into kfifo_out..."), kfifo_out() is marked __must_check, and that causes gcc to produce lots of warnings like this: CC drivers/usb/host/fhci-mem.o In file included from drivers/usb/host/fhci-hcd.c:34: drivers/usb/host/fhci.h: In function 'cq_get': drivers/usb/host/fhci.h:520: warning: ignoring return value of 'kfifo_out', declared with attribute warn_unused_result ... This patch fixes the issue by properly checking the return value. Signed-off-by:
Anton Vorontsov <avorontsov@mvista.com> Cc: stable <stable@kernel.org> [.33 and .34] Signed-off-by:
-
Johan Hovold authored
Remove cp210x_disconnect which is used to kill traffic although this is already handled by the generic framework. Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Julia Lawall authored
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Johan Hovold authored
Compile-only tested. Signed-off-by:
-
Johan Hovold authored
Signed-off-by:
-
Johan Hovold authored
No need to raise dtr/rts in open as this is taken care of by tty layer. Signed-off-by:
-
Johan Hovold authored
Compile-only tested. Signed-off-by:
-
Johan Hovold authored
Use dynamically allocated urb for baudrate changes rather than unconditionally submitting the port write urb which may already be in use. Compile-only tested. Signed-off-by:
-
Johan Hovold authored
Use usb_serial_driver bulk_in_size and bulk_out_size to make sure buffers of appropriate sizes are allocated in the first place rather than reallocating them at every open. Signed-off-by:
-
Johan Hovold authored
If the user specifies a custom bulk buffer size we get a double free at port release. Cc: stable <stable@kernel.org> Signed-off-by:
-
Alan Stern authored
This patch (as1380) fixes a bug in the wakeup settings for EHCI host controllers. When the controller is suspended, if it isn't enabled for remote wakeup then we have to turn off all the port wakeup flags. Disabling PCI PME# isn't good enough, because some systems (Intel) evidently use alternate wakeup signalling paths. In addition, the patch improves the handling of the Intel Moorestown hardware by performing various power-up and power-down delays just once instead of once for each port (i.e., the delays are moved outside of the port loops). This requires extra code, but the total delay time is reduced. There are also a few additional minor cleanups. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Ondrej Zary <linux@rainbow-software.org> CC: Alek Du <alek.du@intel.com> CC: stable <stable@kernel.org> Signed-off-by:
-
Alek Du authored
This is a bug fix for PHCD (phy clock disable) low power feature: After PHCD is set, any write to PORTSC register is illegal, so when resume ports, clear PHCD bit first. Signed-off-by:
Alek Du <alek.du@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by:
-
Randy Dunlap authored
Fix functionfs build to handle CONFIG_NET not enabled, to prevent these build errors: ERROR: "netif_carrier_on" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "netif_carrier_off" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_realloc_headroom" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_trim" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "netif_rx" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "alloc_etherdev_mq" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "ethtool_op_get_link" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "free_netdev" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "register_netdev" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_push" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_pull" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "dev_kfree_skb_any" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_queue_tail" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "__alloc_skb" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "eth_type_trans" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "eth_validate_addr" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_dequeue" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "unregister_netdev" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "__netif_schedule" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "skb_put" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "eth_mac_addr" [drivers/usb/gadget/g_ffs.ko] undefined! ERROR: "dev_get_stats" [drivers/usb/gadget/g_ffs.ko] undefined! Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Acked-by:
Michał Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by:
-
William Gulland authored
Our virtual xHCI device can have as many ports as we like - I've tested this patch with 31. Signed-off-by:
William Gulland <wgulland@vmware.com> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Ming Lei authored
Now on one uses this function and it seems useless, so remove usb_find_device. [tom@tom linux-2.6-next]$ grep -r -n -I usb_find_device ./ drivers/media/dvb/dvb-usb/dvb-usb-init.c:160:static struct dvb_usb_device_description * dvb_usb_find_device(struct usb_device *udev,struct dvb_usb_device_properties *props, int *cold) drivers/media/dvb/dvb-usb/dvb-usb-init.c:230: if ((desc = dvb_usb_find_device(udev,props,&cold)) == NULL) { drivers/usb/core/usb.c:630: * usb_find_device - find a specific usb device in the system drivers/usb/core/usb.c:642:struct usb_device *usb_find_device(u16 vendor_id, u16 product_id) Signed-off-by:Ming Lei <tom.leiming@gmail.com> Signed-off-by:
-
Michal Nazarewicz authored
In to places in fsg_common_init() an unconditional call to kfree() on common was performed in error recovery which is not a valid behaviour since fsg_common structure is not always allocated by fsg_common_init(). To fix, the calls has been replaced with a goto to a proper error recovery which does the correct thing. Also, refactored fsg_common_release() function. Signed-off-by:
Michal Nazarewicz <mina86@mina86.com> Reviewed-by:
Viral Mehta <viral.mehta@lntinfotech.com> Signed-off-by:
-
Ming Lei authored
Obviously, {} is needed in the branch of "else if (hcd->driver->flags & HCD_LOCAL_MEM)" for handling of setup packet mapping. Signed-off-by: -
Anand Gadiyar authored
An undocumented "feature" in the OMAP3 EHCI controller causes suspended ports to be taken out of suspend when the USBCMD.Run/Stop bit is cleared (this bit is normally cleared when ehci_bus_suspend is called). This "feature" breaks suspend-resume if the root-hub is allowed to suspend. (The controller thinks it is in resume, and the PHY thinks it is still in suspend). There is an undocumented register bit that can be used to disable this feature and restore normal behavior. Set this bit so suspend-resume can work normally. Tested on OMAP3 SDPs with the NXP ISP1504 and NXP ISP1703 PHYs. Signed-off-by:
Anand Gadiyar <gadiyar@ti.com> Signed-off-by:
-
Alan Stern authored
This patch (as1379) reworks the logic for handling USB interface runtime-PM settings -- hopefully it's right this time! The problem is that when a driver is unbound or binding fails, runtime PM for the interface always gets disabled. But pm_runtime_disable() nests, so it shouldn't be called unless the interface was previously enabled for runtime PM. Signed-off-by:
Rob Duncan <Robert.Duncan@exar.com> Tested-by:
-
Andiry Xu authored
Macro TRB_TYPE is misused in some places. Fix the wrong usage. Signed-off-by:
Andiry Xu <andiry.xu@amd.com> Cc: stable <stable@kernel.org> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
John Youn authored
Change transfer ring behavior to not follow/activate link TRBs until active TRBs are queued after it. This change affects the behavior when a TD ends just before a link TRB. Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
-
Randy Dunlap authored
Fix g_ffs build error, add a needed header file: drivers/usb/gadget/f_fs.c:1064:error: 'PAGE_CACHE_SIZE' undeclared (first use in this function) drivers/usb/gadget/f_fs.c:1065:error: 'PAGE_CACHE_SHIFT' undeclared (first use in this function) Signed-off-by:
-
Anand Gadiyar authored
On OMAP systems, we have two different OHCI controllers. The legacy one is present in OMAP1/2 chips, and the newer one comes bundled as a companion to the EHCI controller on OMAP3 and newer chips. We may have multi-omap configurations where OMAP2 and OMAP3 support may be enabled in the same kernel, and need a mechanism to keep both drivers around. This patch adds a Kconfig entry for each of these drivers. Signed-off-by:
-
Anand Gadiyar authored
Add support for the OHCI controller present in OMAP3 and newer chips. The code is mostly based off the ehci-omap.c driver. Some of it is common to both drivers and will eventually need to be factored out to platform init files. In its current state, the driver cannot co-exist with the ehci-omap driver, and this will be fixed in later versions. The second driver to be loaded will overwrite settings made by the other. For now, this driver should allow the few users of OMAP3 OHCI to get going. Signed-off-by:
-
Anand Gadiyar authored
Add platform init code for the OMAP3 OHCI driver. Also, configure padconf settings for OMAP3 depending on which port mode is used. Signed-off-by:
-
Dinh Nguyen authored
renamed fsl_mx3_udc.c -> fsl_mxc_udc.c for mx51, usb core is clocked from sources that are not 60mhz. Signed-off-by:
Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by:
-
Johan Hovold authored
Reverse priority of errors reported to ldisc so that it matches that of other serial drivers (break takes precedence over parity, which takes precedence over framing errors). Also make sure overrun errors are handled as in other drivers, that is, an overrun error is always reported and is not associated with any received character (instead a NULL character with the TTY_OVERRUN flag set is inserted). Signed-off-by:
-
Johan Hovold authored
Use tty_insert_flip_string_fixed_flag to report errors to line discipline. Signed-off-by:
-
Johan Hovold authored
Use tty_insert_flip_string_fixed_flag to report errors to line discipline. Signed-off-by:
-
Anton Vorontsov authored
There were some reports[1] of isp1760 USB driver malfunctioning with high speed devices, noticed on Blackfin and PowerPC targets. These reports indicated that the original Philips 'pehcd'[2] driver worked fine. We've noticed the same issue with an ARM RealView platform. This happens under load (with only some mass storage devices, not all, just as in another report[3]): error bit is set in DW3 error bit is set in DW3 error bit is set in DW3 usb 1-1.2: device descriptor read/64, error -32 It appears that the 'pehcd' driver checks the X bit only if the transaction is halted (H bit), otherwise the error is so far insignificant. The ISP176x chips were modeled after EHCI, and EHCI spec says (thanks to Alan Stern for pointing out): "Transaction errors cause the status field to be updated to reflect the type of error, but the transaction continues to be retried until the Active bit is set to 0. When the error counter reaches 0, the Halt bit is set and the Active bit is cleared." So, just as the original Philips driver, isp1760 must report the error only if the transaction error and the halt bits are set. [1] http://markmail.org/message/lx4qrlbrs2uhcnly [2] svn co svn://sources.blackfin.uclinux.org/linux-kernel/trunk/drivers/usb/host -r 5494 See pehci.c:pehci_hcd_update_error_status(). [3] http://blackfin.uclinux.org/gf/tracker/5148Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Andiry Xu authored
When USB3 protocol port detects an USB3.0 device attach, the port will automatically transition to the Enabled state upon the completion of successful link training. Do not disable USB3 protocol ports in hub_activate(), or USB3.0 device will fail to be recognized if xHCI bus power management is implemented. Signed-off-by:
-
Johan Hovold authored
Use process_read_urb to implement read processing. Compile-only tested. Signed-off-by:
Bart Hartgers <bart.hartgers@gmail.com> Signed-off-by:
-
Johan Hovold authored
Fix regression introduced by commit a108bfcb (USB: tty: Prune uses of tty_request_room in the USB layer) which broke three drivers (cypress_m8, digi_acceleport and spcp8x5) through incorrect use of tty_insert_flip_string_fixed_flag. Signed-off-by:
-
