- 21 Sep, 2021 4 commits
-
-
Vladimir Oltean authored
Since the blamed commit, dsa_tree_teardown_switches() was split into two smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports. However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports. Fixes: a57d8c21 ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Karsten Graul says: ==================== net/smc: fixes 2021-09-20 Please apply the following patches for smc to netdev's net tree. The first patch adds a missing error check, and the second patch fixes a possible leak of a lock in a worker. ==================== Signed-off-by: -
Karsten Graul authored
The abort_work is scheduled when a connection was detected to be out-of-sync after a link failure. The work calls smc_conn_kill(), which calls smc_close_active_abort() and that might end up calling smc_close_cancel_work(). smc_close_cancel_work() cancels any pending close_work and tx_work but needs to release the sock_lock before and acquires the sock_lock again afterwards. So when the sock_lock was NOT acquired before then it may be held after the abort_work completes. Thats why the sock_lock is acquired before the call to smc_conn_kill() in __smc_lgr_terminate(), but this is missing in smc_conn_abort_work(). Fix that by acquiring the sock_lock first and release it after the call to smc_conn_kill(). Fixes: b286a065 ("net/smc: handle incoming CDC validation message") Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Karsten Graul authored
Coverity stumbled over a missing error check in smc_clc_prfx_set(): *** CID 1475954: Error handling issues (CHECKED_RETURN) /net/smc/smc_clc.c: 233 in smc_clc_prfx_set() >>> CID 1475954: Error handling issues (CHECKED_RETURN) >>> Calling "kernel_getsockname" without checking return value (as is done elsewhere 8 out of 10 times). 233 kernel_getsockname(clcsock, (struct sockaddr *)&addrs); Add the return code check in smc_clc_prfx_set(). Fixes: c246d942 ("net/smc: restructure netinfo for CLC proposal msgs") Reported-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
- 20 Sep, 2021 11 commits
-
-
David S. Miller authored
Guangbin Huang says: ==================== net: hns3: add some fixes for -net This series adds some fixes for the HNS3 ethernet driver. ==================== Signed-off-by: -
Yufeng Mo authored
hclge_get_reset_status() should return the tqp reset status. However, if the CMDQ fails, the caller will take it as tqp reset success status by mistake. Therefore, uses a parameters to get the tqp reset status instead. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
Yufeng Mo <moyufeng@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
liaoguojia authored
The input parameters may not be reliable, so check the vlan id before using it, otherwise may set wrong vlan id into hardware. Fixes: dc8131d8 ("net: hns3: Fix for packet loss due wrong filter config in VLAN tbls") Signed-off-by:
liaoguojia <liaoguojia@huawei.com> Signed-off-by:
-
Yufeng Mo authored
The input parameters may not be reliable. Before using the queue id, we should check this parameter. Otherwise, memory overwriting may occur. Fixes: d3410018 ("net: hns3: refactor the mailbox message between PF and VF") Signed-off-by:
-
Jiaran Zhang authored
vport_id include PF and VFs, vport_id = 0 means PF, other values mean VFs. So the actual vf id is equal to vport_id minus 1. Some VF print logs are actually vport, and logs of vf id actually use vport id, so this patch fixes them. Fixes: ac887be5 ("net: hns3: change print level of RAS error log from warning to error") Fixes: adcf738b ("net: hns3: cleanup some print format warning") Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by:
-
Jian Shen authored
The vf id from ethtool is added 1 before configured to driver. So it's necessary to minus 1 when printing it, in order to keep consistent with user's configuration. Fixes: dd74f815 ("net: hns3: Add support for rule add/delete for flow director") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
-
Jian Shen authored
When user change rss 'hfunc' without set rss 'hkey' by ethtool -X command, the driver will ignore the 'hfunc' for the hkey is NULL. It's unreasonable. So fix it. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Fixes: 374ad291 ("net: hns3: Add RSS general configuration support for VF") Signed-off-by:
-
Arnd Bergmann authored
Without CONFIG_COMMON_CLK, this fails to link: arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_register_i2c': ptp_ocp.c:(.text+0xcc0): undefined reference to `__clk_hw_register_fixed_rate' arm-linux-gnueabi-ld: ptp_ocp.c:(.text+0xcf4): undefined reference to `devm_clk_hw_register_clkdev' arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_detach': ptp_ocp.c:(.text+0x1c24): undefined reference to `clk_hw_unregister_fixed_rate' Fixes: a7e1abad ("ptp: Add clock driver for the OpenCompute TimeCard.") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Michael Chan authored
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS + 1. Because the first TX BD for a packet is always a long TX BD, we need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with this value to make this more clear. The current code uses a minimum that is off by 1. Fix it using this constant. The tx_wake_thresh to determine when to wake up the TX queue is half the ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next packet which may have maximum fragments. So the comparison of the available TX BDs with tx_wake_thresh should be >= instead of > in the current code. Otherwise, at the smallest ring size, we will never wake up the TX queue and will cause TX timeout. Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by:
Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadocm.com> Signed-off-by:
-
Ido Schimmel authored
The resilient nexthop group torture tests in fib_nexthop.sh exposed a possible division by zero while replacing a resilient group [1]. The division by zero occurs when the data path sees a resilient nexthop group with zero buckets. The tests replace a resilient nexthop group in a loop while traffic is forwarded through it. The tests do not specify the number of buckets while performing the replacement, resulting in the kernel allocating a stub resilient table (i.e, 'struct nh_res_table') with zero buckets. This table should never be visible to the data path, but the old nexthop group (i.e., 'oldg') might still be used by the data path when the stub table is assigned to it. Fix this by only assigning the stub table to the old nexthop group after making sure the group is no longer used by the data path. Tested with fib_nexthops.sh: Tests passed: 222 Tests failed: 0 [1] divide error: 0000 [#1] PREEMPT SMP KASAN CPU: 0 PID: 1850 Comm: ping Not tainted 5.14.0-custom-10271-ga86eb53057fe #1107 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014 RIP: 0010:nexthop_select_path+0x2d2/0x1a80 [...] Call Trace: fib_select_multipath+0x79b/0x1530 fib_select_path+0x8fb/0x1c10 ip_route_output_key_hash_rcu+0x1198/0x2da0 ip_route_output_key_hash+0x190/0x340 ip_route_output_flow+0x21/0x120 raw_sendmsg+0x91d/0x2e10 inet_sendmsg+0x9e/0xe0 __sys_sendto+0x23d/0x360 __x64_sys_sendto+0xe1/0x1b0 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae Cc: stable@vger.kernel.org Fixes: 283a72a5 ("nexthop: Add implementation of resilient next-hop groups") Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
Xuan Zhuo authored
The process will cause napi.state to contain NAPI_STATE_SCHED and not in the poll_list, which will cause napi_disable() to get stuck. The prefix "NAPI_STATE_" is removed in the figure below, and NAPI_STATE_HASHED is ignored in napi.state. CPU0 | CPU1 | napi.state =============================================================================== napi_disable() | | SCHED | NPSVC napi_enable() | | { | | smp_mb__before_atomic(); | | clear_bit(SCHED, &n->state); | | NPSVC | napi_schedule_prep() | SCHED | NPSVC | napi_poll() | | napi_complete_done() | | { | | if (n->state & (NPSVC | | (1) | _BUSY_POLL))) | | return false; | | ................ | | } | SCHED | NPSVC | | clear_bit(NPSVC, &n->state); | | SCHED } | | | | napi_schedule_prep() | | SCHED | MISSED (2) (1) Here return direct. Because of NAPI_STATE_NPSVC exists. (2) NAPI_STATE_SCHED exists. So not add napi.poll_list to sd->poll_list Since NAPI_STATE_SCHED already exists and napi is not in the sd->poll_list queue, NAPI_STATE_SCHED cannot be cleared and will always exist. 1. This will cause this queue to no longer receive packets. 2. If you encounter napi_disable under the protection of rtnl_lock, it will cause the entire rtnl_lock to be locked, affecting the overall system. This patch uses cmpxchg to implement napi_enable(), which ensures that there will be no race due to the separation of clear two bits. Fixes: 2d8bff12 ("netpoll: Close race condition between poll_one_napi and napi_disable") Signed-off-by:Xuan Zhuo <xuanzhuo@linux.alibaba.com> Reviewed-by:
Dust Li <dust.li@linux.alibaba.com> Signed-off-by:
-
- 19 Sep, 2021 22 commits
-
-
Shuah Khan authored
Makefile uses TEST_PROGS instead of TEST_GEN_PROGS to define executables. TEST_PROGS is for shell scripts that need to be installed and run by the common lib.mk framework. The common framework doesn't touch TEST_PROGS when it does build and clean. As a result "make kselftest-clean" and "make clean" fail to remove executables. Run and install work because the common framework runs and installs TEST_PROGS. Build works because the Makefile defines "all" rule which is unnecessary if TEST_GEN_PROGS is used. Use TEST_GEN_PROGS so the common framework can handle build/run/ install/clean properly. Signed-off-by:
Shuah Khan <skhan@linuxfoundation.org> Signed-off-by:
-
Lama Kayal authored
Any link state change that's done prior to net device registration isn't reflected on the state, thus the operational state is left obsolete, with 'UNKNOWN' status. To resolve the issue, query link state from FW upon open operations to ensure operational state is updated. Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by:
Lama Kayal <lkayal@nvidia.com> Signed-off-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
-
Shuah Khan authored
Fix the args to fprintf(). Splitting the message ends up passing incorrect arg for "sigurg %d" and an extra arg overall. The test result message ends up incorrect. test_unix_oob.c: In function ‘main’: test_unix_oob.c:274:43: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘char *’ [-Wformat=] 274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ", | ~^ | | | int | %s 275 | "atmark %d\n", signal_recvd, len, oob, atmark); | ~~~~~~~~~~~~~ | | | char * test_unix_oob.c:274:19: warning: too many arguments for format [-Wformat-extra-args] 274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ", Signed-off-by: -
Christian Lamparter authored
Due to the inclusion of nvmem handling into the mac-address getter function of_get_mac_address() by commit d01f449c ("of_net: add NVMEM support to of_get_mac_address") it is now possible to get a -EPROBE_DEFER return code. Which did cause bgmac to assign a random ethernet address. This exact issue happened on my Meraki MR32. The nvmem provider is an EEPROM (at24c64) which gets instantiated once the module driver is loaded... This happens once the filesystem becomes available. With this patch, bgmac_probe() will propagate the -EPROBE_DEFER error. Then the driver subsystem will reschedule the probe at a later time. Cc: Petr Štetiar <ynezz@true.cz> Cc: Michael Walle <michael@walle.cc> Fixes: d01f449c ("of_net: add NVMEM support to of_get_mac_address") Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
Commit 86f8b1c0 ("net: dsa: Do not make user port errors fatal") decided it was fine to ignore errors on certain ports that fail to probe, and go on with the ports that do probe fine. Commit fb6ec87f ("net: dsa: Fix type was not set for devlink port") noticed that devlink_port_type_eth_set(dlp, dp->slave); does not get called, and devlink notices after a timeout of 3600 seconds and prints a WARN_ON. So it went ahead to unregister the devlink port. And because there exists an UNUSED port flavour, we actually re-register the devlink port as UNUSED. Commit 08156ba4 ("net: dsa: Add devlink port regions support to DSA") added devlink port regions, which are set up by the driver and not by DSA. When we trigger the devlink port deregistration and reregistration as unused, devlink now prints another WARN_ON, from here: devlink_port_unregister: WARN_ON(!list_empty(&devlink_port->region_list)); So the port still has regions, which makes sense, because they were set up by the driver, and the driver doesn't know we're unregistering the devlink port. Somebody needs to tear them down, and optionally (actually it would be nice, to be consistent) set them up again for the new devlink port. But DSA's layering stays in our way quite badly here. The options I've considered are: 1. Introduce a function in devlink to just change a port's type and flavour. No dice, devlink keeps a lot of state, it really wants the port to not be registered when you set its parameters, so changing anything can only be done by destroying what we currently have and recreating it. 2. Make DSA cache the parameters passed to dsa_devlink_port_region_create, and the region returned, keep those in a list, then when the devlink port unregister needs to take place, the existing devlink regions are destroyed by DSA, and we replay the creation of new regions using the cached parameters. Problem: mv88e6xxx keeps the region pointers in chip->ports[port].region, and these will remain stale after DSA frees them. There are many things DSA can do, but updating mv88e6xxx's private pointers is not one of them. 3. Just let the driver do it (i.e. introduce a very specific method called ds->ops->port_reinit_as_unused, which unregisters its devlink port devlink regions, then the old devlink port, then registers the new one, then the devlink port regions for it). While it does work, as opposed to the others, it's pretty horrible from an API perspective and we can do better. 4. Introduce a new pair of methods, ->port_setup and ->port_teardown, which in the case of mv88e6xxx must register and unregister the devlink port regions. Call these 2 methods when the port must be reinitialized as unused. Naturally, I went for the 4th approach. Fixes: 08156ba4 ("net: dsa: Add devlink port regions support to DSA") Signed-off-by:
-
Krzysztof Kozlowski authored
The MODULE_DEVICE_TABLE already creates proper alias for platform driver. Having another MODULE_ALIAS causes the alias to be duplicated. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
David S. Miller authored
Colin Foster says: ==================== ocelot phylink fixes When the ocelot driver was migrated to phylink, e6e12df6 ("net: mscc: ocelot: convert to phylink") there were two additional writes to registers that became stale. One write was to DEV_CLOCK_CFG and one was to ANA_PFC_PCF_CFG. Both of these writes referenced the variable "speed" which originally was set to OCELOT_SPEED_{10,100,1000,2500}. These macros expand to values of 3, 2, 1, or 0, respectively. After the update, the variable speed is set to SPEED_{10,100,1000,2500} which expand to 10, 100, 1000, and 2500. So invalid values were getting written to the two registers, which would lead to either a lack of functionality or undefined funcationality. Fixing these values was the intent of v1 of this patch set - submitted as "[PATCH v1 net] net: ethernet: mscc: ocelot: bug fix when writing MAC speed" During that review it was determined that both writes were actually unnecessary. DEV_CLOCK_CFG is a duplicate write, so can be removed entirely. This was accidentally submitted as as a new, lone patch titled "[PATCH v1 net] net: mscc: ocelot: remove buggy duplicate write to DEV_CLOCK_CFG". This is part of what is considered v2 of this patch set. Additionally, the write to ANA_PFC_PFC_CFG is also unnecessary. Priority flow contol is disabled, so configuring it is useless and should be removed. This was also submitted as a new, lone patch titled "[PATCH v1 net] net: mscc: ocelot: remove buggy and useless write to ANA_PFC_PFC_CFG". This is the rest of what is considered v2 of this patch set. v3 Identical to v2, but fixes the patch numbering to v3 and submitting the two changes as a patch set. v2 Note: I misunderstood and submitted two new "v1" patches instead of a single "v2" patch set. - Remove the buggy writes altogher ==================== Signed-off-by:
-
Colin Foster authored
When updating ocelot to use phylink, a second write to DEV_CLOCK_CFG was mistakenly left in. It used the variable "speed" which, previously, would would have been assigned a value of OCELOT_SPEED_1000. In phylink the variable is be SPEED_1000, which is invalid for the DEV_CLOCK_LINK_SPEED macro. Removing it as unnecessary and buggy. Fixes: e6e12df6 ("net: mscc: ocelot: convert to phylink") Signed-off-by:
Colin Foster <colin.foster@in-advantage.com> Reviewed-by:
-
Colin Foster authored
A useless write to ANA_PFC_PFC_CFG was left in while refactoring ocelot to phylink. Since priority flow control is disabled, writing the speed has no effect. Further, it was using ethtool.h SPEED_ instead of OCELOT_SPEED_ macros, which are incorrectly offset for GENMASK. Lastly, for priority flow control to properly function, some scenarios would rely on the rate adaptation from the PCS while the MAC speed would be fixed. So it isn't used, and even if it was, neither "speed" nor "mac_speed" are necessarily the correct values to be used. Fixes: e6e12df6 ("net: mscc: ocelot: convert to phylink") Signed-off-by:
-
Thomas Gleixner authored
lock_sock_fast() and lock_sock_nested() contain lockdep annotations for the sock::sk_lock.owned 'mutex'. sock::sk_lock.owned is not a regular mutex. It is just lockdep wise equivalent. In fact it's an open coded trivial mutex implementation with some interesting features. sock::sk_lock.slock is a regular spinlock protecting the 'mutex' representation sock::sk_lock.owned which is a plain boolean. If 'owned' is true, then some other task holds the 'mutex', otherwise it is uncontended. As this locking construct is obviously endangered by lock ordering issues as any other locking primitive it got lockdep annotated via a dedicated dependency map sock::sk_lock.dep_map which has to be updated at the lock and unlock sites. lock_sock_nested() is a straight forward 'mutex' lock operation: might_sleep(); spin_lock_bh(sock::sk_lock.slock) while (!try_lock(sock::sk_lock.owned)) { spin_unlock_bh(sock::sk_lock.slock); wait_for_release(); spin_lock_bh(sock::sk_lock.slock); } The lockdep annotation for sock::sk_lock.owned is for unknown reasons _after_ the lock has been acquired, i.e. after the code block above and after releasing sock::sk_lock.slock, but inside the bottom halves disabled region: spin_unlock(sock::sk_lock.slock); mutex_acquire(&sk->sk_lock.dep_map, subclass, 0, _RET_IP_); local_bh_enable(); The placement after the unlock is obvious because otherwise the mutex_acquire() would nest into the spin lock held region. But that's from the lockdep perspective still the wrong place: 1) The mutex_acquire() is issued _after_ the successful acquisition which is pointless because in a dead lock scenario this point is never reached which means that if the deadlock is the first instance of exposing the wrong lock order lockdep does not have a chance to detect it. 2) It only works because lockdep is rather lax on the context from which the mutex_acquire() is issued. Acquiring a mutex inside a bottom halves and therefore non-preemptible region is obviously invalid, except for a trylock which is clearly not the case here. This 'works' stops working on RT enabled kernels where the bottom halves serialization is done via a local lock, which exposes this misplacement because the 'mutex' and the local lock nest the wrong way around and lockdep complains rightfully about a lock inversion. The placement is wrong since the initial commit a5b5bb9a ("[PATCH] lockdep: annotate sk_locks") which introduced this. Fix it by moving the mutex_acquire() in front of the actual lock acquisition, which is what the regular mutex_lock() operation does as well. lock_sock_fast() is not that straight forward. It looks at the first glance like a convoluted trylock operation: spin_lock_bh(sock::sk_lock.slock) if (!sock::sk_lock.owned) return false; while (!try_lock(sock::sk_lock.owned)) { spin_unlock_bh(sock::sk_lock.slock); wait_for_release(); spin_lock_bh(sock::sk_lock.slock); } spin_unlock(sock::sk_lock.slock); mutex_acquire(&sk->sk_lock.dep_map, subclass, 0, _RET_IP_); local_bh_enable(); return true; But that's not the case: lock_sock_fast() is an interesting optimization for short critical sections which can run with bottom halves disabled and sock::sk_lock.slock held. This allows to shortcut the 'mutex' operation in the non contended case by preventing other lockers to acquire sock::sk_lock.owned because they are blocked on sock::sk_lock.slock, which in turn avoids the overhead of doing the heavy processing in release_sock() including waking up wait queue waiters. In the contended case, i.e. when sock::sk_lock.owned == true the behavior is the same as lock_sock_nested(). Semantically this shortcut means, that the task acquired the 'mutex' even if it does not touch the sock::sk_lock.owned field in the non-contended case. Not telling lockdep about this shortcut acquisition is hiding potential lock ordering violations in the fast path. As a consequence the same reasoning as for the above lock_sock_nested() case vs. the placement of the lockdep annotation applies. The current placement of the lockdep annotation was just copied from the original lock_sock(), now renamed to lock_sock_nested(), implementation. Fix this by moving the mutex_acquire() in front of the actual lock acquisition and adding the corresponding mutex_release() into unlock_sock_fast(). Also document the fast path return case with a comment. Reported-by:Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: netdev@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Alejandro Concepcion-Rodriguez authored
The file sja1105.txt was converted to nxp,sja1105.yaml. Signed-off-by:
Alejandro Concepcion-Rodriguez <asconcepcion@acoro.eu> Signed-off-by:
-
Randy Dunlap authored
When IGC=y and PTP_1588_CLOCK=m, the ptp_*() interface family is not available to the igc driver. Make this driver depend on PTP_1588_CLOCK_OPTIONAL so that it will build without errors. Various igc commits have used ptp_*() functions without checking that PTP_1588_CLOCK is enabled. Fix all of these here. Fixes these build errors: ld: drivers/net/ethernet/intel/igc/igc_main.o: in function `igc_msix_other': igc_main.c:(.text+0x6494): undefined reference to `ptp_clock_event' ld: igc_main.c:(.text+0x64ef): undefined reference to `ptp_clock_event' ld: igc_main.c:(.text+0x6559): undefined reference to `ptp_clock_event' ld: drivers/net/ethernet/intel/igc/igc_ethtool.o: in function `igc_ethtool_get_ts_info': igc_ethtool.c:(.text+0xc7a): undefined reference to `ptp_clock_index' ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_feature_enable_i225': igc_ptp.c:(.text+0x330): undefined reference to `ptp_find_pin' ld: igc_ptp.c:(.text+0x36f): undefined reference to `ptp_find_pin' ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_init': igc_ptp.c:(.text+0x11cd): undefined reference to `ptp_clock_register' ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_stop': igc_ptp.c:(.text+0x12dd): undefined reference to `ptp_clock_unregister' ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe': Fixes: 64433e5b ("igc: Enable internal i225 PPS") Fixes: 60dbede0 ("igc: Add support for ethtool GET_TS_INFO command") Fixes: 87938851 ("igc: enable auxiliary PHC functions for the i225") Fixes: 5f295805 ("igc: Add basic skeleton for PTP") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Ederson de Souza <ederson.desouza@intel.com> Cc: Tony Nguyen <anthony.l.nguyen@intel.com> Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: intel-wired-lan@lists.osuosl.org Acked-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by:
-
Claudiu Manoil authored
The only struct dim_sample member that does not get initialized by dim_update_sample() is comp_ctr. (There is special API to initialize comp_ctr: dim_update_sample_with_comps(), and it is currently used only for RDMA.) comp_ctr is used to compute curr_stats->cmps and curr_stats->cpe_ratio (see dim_calc_stats()) which in turn are consumed by the rdma_dim_*() API. Therefore, functionally, the net_dim*() API consumers are not affected. Nevertheless, fix the computation of statistics based on an uninitialized variable, even if the mentioned statistics are not used at the moment. Fixes: ae0e6a5d ("enetc: Add adaptive interrupt coalescing") Signed-off-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
-
Claudiu Manoil authored
irq_set_affinity_hit() stores a reference to the cpumask_t parameter in the irq descriptor, and that reference can be accessed later from irq_affinity_hint_proc_show(). Since the cpu_mask parameter passed to irq_set_affinity_hit() has only temporary storage (it's on the stack memory), later accesses to it are illegal. Thus reads from the corresponding procfs affinity_hint file can result in paging request oops. The issue is fixed by the get_cpu_mask() helper, which provides a permanent storage for the cpumask_t parameter. Fixes: d4fd0404 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by:
-
Jason Wang authored
We try to use build_skb() if we had sufficient tailroom. But we forget to release the unused pages chained via private in big mode which will leak pages. Fixing this by release the pages after building the skb in big mode. Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Fixes: fb32856b ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom") Signed-off-by:
Jason Wang <jasowang@redhat.com> Reviewed-by:
-
Jan Beulich authored
When re-entering the main loop of xenvif_tx_check_gop() a 2nd time, the special considerations for the head of the SKB no longer apply. Don't mistakenly report ERROR to the frontend for the first entry in the list, even if - from all I can tell - this shouldn't matter much as the overall transmit will need to be considered failed anyway. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Reviewed-by:
Paul Durrant <paul@xen.org> Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Make DSA switch drivers compatible with masters which unregister on shutdown Changes in v2: - fix build for b53_mmap - use unregister_netdevice_many It was reported by Lino here: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/ that when the DSA master attempts to unregister its net_device on shutdown, DSA should prevent that operation from succeeding because it holds a reference to it. This hangs the shutdown process. This issue was essentially introduced in commit 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings"). The present series patches all DSA drivers to handle that case, depending on whether those drivers were introduced before or after the offending commit, a different Fixes: tag is specified for them. The approach taken by this series solves the issue in essentially the same way as Lino's patches, except for three key differences: - this series takes a more minimal approach in what is done on shutdown, we do not attempt a full tree teardown as that is not strictly necessary. I might revisit this if there are compelling reasons to do otherwise - this series fixes the issues for all DSA drivers, not just KSZ9897 - this series works even if the ->remove driver method gets called for the same device too, not just ->shutdown. This is really possible to happen for SPI device drivers, and potentially possible for other bus device drivers too. ==================== Signed-off-by:
-
Vladimir Oltean authored
Since commit 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings"), DSA gained a requirement which it did not fulfill, which is to unlink itself from the DSA master at shutdown time. Since the Arrow SpeedChips XRS700x driver was introduced after the bad commit, it has never worked with DSA masters which decide to unregister their net_device on shutdown, effectively hanging the reboot process. To fix that, we need to call dsa_switch_shutdown. These devices can be connected by I2C or by MDIO, and if I search for I2C or MDIO bus drivers that implement their ->shutdown by redirecting it to ->remove I don't see any, however this does not mean it would not be possible. To be compatible with that pattern, it is necessary to implement an "if this then not that" scheme, to avoid ->remove and ->shutdown from being called both for the same struct device. Fixes: ee00b24f ("net: dsa: add Arrow SpeedChips XRS700x driver") Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/Reported-by:
Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by:
George McCollister <george.mccollister@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
Since commit 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings"), DSA gained a requirement which it did not fulfill, which is to unlink itself from the DSA master at shutdown time. Since the Microchip sub-driver for KSZ8863 was introduced after the bad commit, it has never worked with DSA masters which decide to unregister their net_device on shutdown, effectively hanging the reboot process. To fix that, we need to call dsa_switch_shutdown. Since this driver expects the MDIO bus to be backed by mdio_bitbang, I don't think there is currently any MDIO bus driver which implements its ->shutdown by redirecting it to ->remove, but in any case, to be compatible with that pattern, it is necessary to implement an "if this then not that" scheme, to avoid ->remove and ->shutdown from being called both for the same struct device. Fixes: 60a36476 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support") Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/Reported-by:
-
Vladimir Oltean authored
Since commit 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings"), DSA gained a requirement which it did not fulfill, which is to unlink itself from the DSA master at shutdown time. Since the hellcreek driver was introduced after the bad commit, it has never worked with DSA masters which decide to unregister their net_device on shutdown, effectively hanging the reboot process. Hellcreek is a platform device driver, so we probably cannot have the oddities of ->shutdown and ->remove getting both called for the exact same struct device. But to be in line with the pattern from the other device drivers which are on slow buses, implement the same "if this then not that" pattern of either running the ->shutdown or the ->remove hook. The driver's current ->remove implementation makes that very easy because it already zeroes out its device_drvdata on ->remove. Fixes: e4b27ebc ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches") Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/Reported-by:
Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by:
-
Vladimir Oltean authored
Lino reports that on his system with bcmgenet as DSA master and KSZ9897 as a switch, rebooting or shutting down never works properly. What does the bcmgenet driver have special to trigger this, that other DSA masters do not? It has an implementation of ->shutdown which simply calls its ->remove implementation. Otherwise said, it unregisters its network interface on shutdown. This message can be seen in a loop, and it hangs the reboot process there: unregister_netdevice: waiting for eth0 to become free. Usage count = 3 So why 3? A usage count of 1 is normal for a registered network interface, and any virtual interface which links itself as an upper of that will increment it via dev_hold. In the case of DSA, this is the call path: dsa_slave_create -> netdev_upper_dev_link -> __netdev_upper_dev_link -> __netdev_adjacent_dev_insert -> dev_hold So a DSA switch with 3 interfaces will result in a usage count elevated by two, and netdev_wait_allrefs will wait until they have gone away. Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and delete themselves, but DSA cannot just vanish and go poof, at most it can unbind itself from the switch devices, but that must happen strictly earlier compared to when the DSA master unregisters its net_device, so reacting on the NETDEV_UNREGISTER event is way too late. It seems that it is a pretty established pattern to have a driver's ->shutdown hook redirect to its ->remove hook, so the same code is executed regardless of whether the driver is unbound from the device, or the system is just shutting down. As Florian puts it, it is quite a big hammer for bcmgenet to unregister its net_device during shutdown, but having a common code path with the driver unbind helps ensure it is well tested. So DSA, for better or for worse, has to live with that and engage in an arms race of implementing the ->shutdown hook too, from all individual drivers, and do something sane when paired with masters that unregister their net_device there. The only sane thing to do, of course, is to unlink from the master. However, complications arise really quickly. The pattern of redirecting ->shutdown to ->remove is not unique to bcmgenet or even to net_device drivers. In fact, SPI controllers do it too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers and MDIO controllers do it too (this is something I have not researched too deeply, but even if this is not the case today, it is certainly plausible to happen in the future, and must be taken into consideration). Since DSA switches might be SPI devices, I2C devices, MDIO devices, the insane implication is that for the exact same DSA switch device, we might have both ->shutdown and ->remove getting called. So we need to do something with that insane environment. The pattern I've come up with is "if this, then not that", so if either ->shutdown or ->remove gets called, we set the device's drvdata to NULL, and in the other hook, we check whether the drvdata is NULL and just do nothing. This is probably not necessary for platform devices, just for devices on buses, but I would really insist for consistency among drivers, because when code is copy-pasted, it is not always copy-pasted from the best sources. So depending on whether the DSA switch's ->remove or ->shutdown will get called first, we cannot really guarantee even for the same driver if rebooting will result in the same code path on all platforms. But nonetheless, we need to do something minimally reasonable on ->shutdown too to fix the bug. Of course, the ->remove will do more (a full teardown of the tree, with all data structures freed, and this is why the bug was not caught for so long). The new ->shutdown method is kept separate from dsa_unregister_switch not because we couldn't have unregistered the switch, but simply in the interest of doing something quick and to the point. The big question is: does the DSA switch's ->shutdown get called earlier than the DSA master's ->shutdown? If not, there is still a risk that we might still trigger the WARN_ON in unregister_netdevice that says we are attempting to unregister a net_device which has uppers. That's no good. Although the reference to the master net_device won't physically go away even if DSA's ->shutdown comes afterwards, remember we have a dev_hold on it. The answer to that question lies in this comment above device_link_add: * A side effect of the link creation is re-ordering of dpm_list and the * devices_kset list by moving the consumer device and all devices depending * on it to the ends of these lists (that does not happen to devices that have * not been registered when this function is called). so the fact that DSA uses device_link_add towards its master is not exactly for nothing. device_shutdown() walks devices_kset from the back, so this is our guarantee that DSA's shutdown happens before the master's shutdown. Fixes: 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings") Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/Reported-by:Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Vladimir Oltean authored
MDIO-attached devices might have interrupts and other things that might need quiesced when we kexec into a new kernel. Things are even more creepy when those interrupt lines are shared, and in that case it is absolutely mandatory to disable all interrupt sources. Moreover, MDIO devices might be DSA switches, and DSA needs its own shutdown method to unlink from the DSA master, which is a new requirement that appeared after commit 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings"). So introduce a ->shutdown method in the MDIO device driver structure. Signed-off-by:
-
- 17 Sep, 2021 3 commits
-
-
Florian Fainelli authored
After d12e1c46 ("net: dsa: b53: Set correct number of ports in the DSA struct") we stopped setting dsa_switch::num_ports to DSA_MAX_PORTS, which created an off by one error between the statically allocated bcm_sf2_priv::port_sts array (of size DSA_MAX_PORTS). When dsa_is_cpu_port() is used, we end-up accessing an out of bounds member and causing a NPD. Fix this by iterating with the appropriate port count using ds->num_ports. Fixes: d12e1c46 ("net: dsa: b53: Set correct number of ports in the DSA struct") Signed-off-by:
-
Vladimir Oltean authored
NXP Legal insists that the following are not fine: - Saying "NXP Semiconductors" instead of "NXP", since the company's registered name is "NXP" - Putting a "(c)" sign in the copyright string - Putting a comma in the copyright string The only accepted copyright string format is "Copyright <year-range> NXP". This patch changes the copyright headers in the networking files that were sent by me, or derived from code sent by me. Signed-off-by:
-
Johan Hovold authored
If resource allocation and registration fail for a muxed tty device (e.g. if there are no more minor numbers) the driver should not try to deregister the never-registered (or already-deregistered) tty. Fix up the error handling to avoid dereferencing a NULL pointer when attempting to remove the character device. Fixes: 72dc1c09 ("HSO: add option hso driver") Cc: stable@vger.kernel.org # 2.6.27 Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
