- 17 Mar, 2009 24 commits
-
-
Achilleas Kotsis authored
Option GTM380 in Modem mode uses Product ID 0x7201. This has been tested and works on production systems for over 6 months. Signed-off-by:
Achilleas Kotsis <akots@exponent.gr> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Dirk Hohndel authored
* newer versions of the Novatel Wireless U727 CDMA 3G USB stick have a different Product ID (0x5010); adding this ID makes them work just fine with the option driver Signed-off-by:
Dirk Hohndel <hohndel@infradead.org> Cc: stable <stable@kernel.org> Signed-off-by:
-
Moritz Muehlenhoff authored
Current firmware revision 5.60 still behaves the same, so update the quirk up a (non-existing) 99.99 revision. http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=493415Signed-off-by:
Moritz Muehlenhoff <jmm@debian.org> Tested-by:
Jan Heitkoetter <devnull@heitkoetter.net> Cc: stable <stable@kernel.org> Signed-off-by:
Phil Dibowitz <phil@ipom.com>
-
Dan Williams authored
The generic cdc-acm driver is now the best one to handle Sony Ericsson F3507g-based devices (which the Dell 5530 is a rebrand of), now that all the pieces are in place (ie, cac477e8). Removing the IDs from option allows cdc-acm to handle the device. Signed-off-by:
Dan Williams <dcbw@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by:
-
Alan Stern authored
This patch (as1225) fixes a bug in ehci-hcd. The condition for whether unlinked QHs can become IDLE should not be that the controller is halted, but rather that the controller isn't running. In other words when the root hub is suspended, the hardware doesn't own any QHs. This fixes a problem that can show up during hibernation: If a QH is only partially unlinked when the root hub is frozen, then when the root hub is thawed the QH won't be in the IDLE state. As a result it can't be used properly for new URB submissions. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Brandon Philips <brandon@ifup.org> Tested-by:
David Brownell <dbrownell@users.sourceforge.net> Cc: Stable <stable@kernel.org> Signed-off-by:
-
Karsten Wiese authored
ehci-hcd uses usb_get_urb() and usb_put_urb() in an unbalanced way causing isochronous URB's kref.counts incrementing once per usb_submit_urb() call. The culprit is *usb being set to NULL when usb_put_urb() is called after URB is given back. Due to other fixes there is no need for ehci-hcd to deal with usb_get_urb() nor usb_put_urb() anymore, so patch removes their usages in ehci-hcd. Patch also makes ehci_to_hcd(ehci)->self.bandwidth_allocated adjust, if a stream finishes. Signed-off-by:
Karsten Wiese <fzu@wemgehoertderstaat.de> Cc: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by:
-
Albert Pauw authored
Please consider this small patch for the usb option-card driver. This patch adds the ZTE 622 usb modem device. Signed-off-by:
Albert Pauw <albert.pauw@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by:
-
Jiri Slaby authored
Fix locking on one wa_urb_enqueue_b's fail path. There was omitted unlock. Signed-off-by:
Jiri Slaby <jirislaby@gmail.com> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Signed-off-by:
-
Jiri Slaby authored
Make sure we don't leak locked vstdev->lock in vstusb_write. Unlock properly on one fail path. Signed-off-by:
-
Jiri Slaby authored
Don't unlock adutux_mutex when not held. Signed-off-by:
-
Jiri Slaby authored
There is an omitted unlock in mdc800_usb_probe's fail path. Add it. Signed-off-by:
-
Jiri Slaby authored
We do not hold mutex in one place in cxacru_cm, but unlock it on fail path. Fix this. Signed-off-by:
-
Jan Dumon authored
Enable the SD-Card interface on the GI 0431 HSUPA stick from Option. The unusual_devs.h entry is necessary because the device descriptor is vendor-specific. That prevents usb-storage from binding to it as an interface driver. T: Bus=07 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 15 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1 P: Vendor=0af0 ProdID=7501 Rev= 0.00 S: Manufacturer=Option N.V. S: Product=Globetrotter HSUPA Modem C:* #Ifs=11 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 9 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=10 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by:
Jan Dumon <j.dumon@option.com> Signed-off-by:
-
Robert M. Kenney authored
From: Robert M. Kenney <rmk@unh.edu> Cc: stable <stable@kernel.org> Signed-off-by: -
Michael Hennerich authored
Signed-off-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
Bryan Wu <cooloney@kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by:
-
Axel Wachtler authored
Add the following devices to the USB FTDI SIO device table: Bus 001 Device 009: ID 03eb:2109 Atmel Corp. http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4187 Bus 001 Device 008: ID 1cf1:0001 http://www.dresden-elektronik.de/shop/prod75.html Bus 001 Device 007: ID 1c1f:0004 http://www.dresden-elektronik.de/shop/prod64.htmlSigned-off-by:
Axel Wachtler <axel.wachtler@atmel.com> Signed-off-by:
Robert Richter <robert.richter@amd.com> Signed-off-by:
-
Alan Stern authored
The usbfs driver manages a list of completed asynchronous URBs. But it is too eager to free the entries on this list: destroy_async() gets called whenever an interface is unbound or a device is removed, and it deallocates the outstanding struct async entries for all URBs on that interface or device. This is wrong; the user program should be able to reap an URB any time after it has completed, regardless of whether or not the interface is still bound or the device is still present. This patch (as1222) moves the code for deallocating the completed list entries from destroy_async() to usbdev_release(). The outstanding entries won't be freed until the user program has closed the device file, thereby eliminating any possibility that the remaining URBs might still be reaped. This fixes a bug in which a program can hang in the USBDEVFS_REAPURB ioctl when the device is unplugged. Reported-and-tested-by:
Martin Poupe <martin.poupe@upek.com> Signed-off-by:
-
Greg Kroah-Hartman authored
The driver already supports the 1 protocol support, so just add it to the MODULE_DEVICE_TABLE entry so it properly picks up these devices. Thanks to Jouni Rynö for pointing this out. Reported-by:
Jouni Ryno <Jouni.Ryno@fmi.fi> Cc: stable <stable@kernel.org> Signed-off-by:
-
Greg Kroah-Hartman authored
open() will never succeed, as we always return -ENODEV. Fix this obvious bug. Thanks to Jouni Ryno for reporting it. Reported-by:
-
Linus Torvalds authored
Commit ee6f779b ("filp->f_pos not correctly updated in proc_task_readdir") changed the proc code to use filp->f_pos directly, rather than through a temporary variable. In the process, that caused the operations to be done on the full 64 bits, even though the offset is never that big. That's all fine and dandy per se, but for some unfathomable reason gcc generates absolutely horrid code when using 64-bit values in switch() statements. To the point of actually calling out to gcc helper functions like __cmpdi2 rather than just doing the trivial comparisons directly the way gcc does for normal compares. At which point we get link failures, because we really don't want to support that kind of crazy code. Fix this by just casting the f_pos value to "unsigned long", which is plenty big enough for /proc, and avoids the gcc code generation issue. Reported-by:
Alexey Dobriyan <adobriyan@gmail.com> Cc: Zhang Le <r0bertz@gentoo.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Masami Hiramatsu authored
Don't boost at the addresses which are listed on exception tables, because major page fault will occur on those addresses. In that case, kprobes can not ensure that when instruction buffer can be freed since some processes will sleep on the buffer. kprobes-ia64 already has same check. Signed-off-by:
Masami Hiramatsu <mhiramat@redhat.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dmLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: dm crypt: wait for endio to complete before destruction dm crypt: fix kcryptd_async_done parameter dm io: respect BIO_MAX_PAGES limit dm table: rework reference counting fix dm ioctl: validate name length when renaming
-
Linus Torvalds authored
In order for ntpd to correctly synchronize the clocks, the frequency of the system clock must not be off by more than 500 ppm (or, put another way, 1:2000), or ntpd will end up giving up on trying to synchronize properly, and ends up reseting the clock in jumps instead. The fast TSC PIT calibration sometimes failed this test - it was assuming that the PIT reads always took about one microsecond each (2us for the two reads to get a 16-bit timer), and that calibrating TSC to the PIT over 15ms should thus be sufficient to get much closer than 500ppm (max 2us error on both sides giving 4us over 15ms: a 270 ppm error value). However, that assumption does not always hold: apparently some hardware is either very much slower at reading the PIT registers, or there was other noise causing at least one machine to get 700+ ppm errors. So instead of using a fixed 15ms timing loop, this changes the fast PIT calibration to read the TSC delta over the individual PIT timer reads, and use the result to calculate the error bars on the PIT read timing properly. We then successfully calibrate the TSC only if the maximum error bars fall below 500ppm. In the process, we also relax the timing to allow up to 25ms for the calibration, although it can happen much faster depending on hardware. Reported-and-tested-by:
Jesper Krogh <jesper@krogh.cc> Cc: john stultz <johnstul@us.ibm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Linus Torvalds authored
During bootup, when we reprogram the PIT (programmable interval timer) to start counting down from 0xffff in order to use it for the fast TSC calibration, we should also make sure to delay a bit afterwards to allow the PIT hardware to actually start counting with the new value. That will happens at the next CLK pulse (1.193182 MHz), so the easiest way to do that is to just wait at least one microsecond after programming the new PIT counter value. We do that by just reading the counter value back once - which will take about 2us on PC hardware. Reported-and-tested-by:
john stultz <johnstul@us.ibm.com> Signed-off-by:
-
- 16 Mar, 2009 16 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6Linus Torvalds authored
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: acpi-wmi: unsigned cannot be less than 0 thinkpad-acpi: fix module autoloading for older models acer-wmi: Unmark as 'experimental' acpi-wmi: Unmark as 'experimental' acer-wmi: double free in acer_rfkill_exit() platform/x86: depends instead of select for laptop platform drivers asus-laptop: use select instead of depends on eeepc-laptop: restore acpi_generate_proc_event() asus-laptop: restore acpi_generate_proc_event() acpi: check for pxm_to_node_map overflow ACPI: remove doubled status checking ACPI suspend: Blacklist Toshiba Satellite L300 that requires to set SCI_EN directly on resume Revert "ACPI: make some IO ports off-limits to AML" suspend: switch the Asus Pundit P1-AH2 to old ACPI sleep ordering
-
Milan Broz authored
The following oops has been reported when dm-crypt runs over a loop device. ... [ 70.381058] Process loop0 (pid: 4268, ti=cf3b2000 task=cf1cc1f0 task.ti=cf3b2000) ... [ 70.381058] Call Trace: [ 70.381058] [<d0d76601>] ? crypt_dec_pending+0x5e/0x62 [dm_crypt] [ 70.381058] [<d0d767b8>] ? crypt_endio+0xa2/0xaa [dm_crypt] [ 70.381058] [<d0d76716>] ? crypt_endio+0x0/0xaa [dm_crypt] [ 70.381058] [<c01a2f24>] ? bio_endio+0x2b/0x2e [ 70.381058] [<d0806530>] ? dec_pending+0x224/0x23b [dm_mod] [ 70.381058] [<d08066e4>] ? clone_endio+0x79/0xa4 [dm_mod] [ 70.381058] [<d080666b>] ? clone_endio+0x0/0xa4 [dm_mod] [ 70.381058] [<c01a2f24>] ? bio_endio+0x2b/0x2e [ 70.381058] [<c02bad86>] ? loop_thread+0x380/0x3b7 [ 70.381058] [<c02ba8a1>] ? do_lo_send_aops+0x0/0x165 [ 70.381058] [<c013754f>] ? autoremove_wake_function+0x0/0x33 [ 70.381058] [<c02baa06>] ? loop_thread+0x0/0x3b7 When a table is being replaced, it waits for I/O to complete before destroying the mempool, but the endio function doesn't call mempool_free() until after completing the bio. Fix it by swapping the order of those two operations. The same problem occurs in dm.c with md referenced after dec_pending. Again, we swap the order. Cc: stable@kernel.org Signed-off-by:
Milan Broz <mbroz@redhat.com> Signed-off-by:
Alasdair G Kergon <agk@redhat.com>
-
Huang Ying authored
In the async encryption-complete function (kcryptd_async_done), the crypto_async_request passed in may be different from the one passed to crypto_ablkcipher_encrypt/decrypt. Only crypto_async_request->data is guaranteed to be same as the one passed in. The current kcryptd_async_done uses the passed-in crypto_async_request directly which may cause the AES-NI-based AES algorithm implementation to panic. This patch fixes this bug by only using crypto_async_request->data, which points to dm_crypt_request, the crypto_async_request passed in. The original data (convert_context) is gotten from dm_crypt_request. [mbroz@redhat.com: reworked] Cc: stable@kernel.org Signed-off-by:
Huang Ying <ying.huang@intel.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Mikulas Patocka authored
dm-io calls bio_get_nr_vecs to get the maximum number of pages to use for a given device. It allocates one additional bio_vec to use internally but failed to respect BIO_MAX_PAGES, so fix this. This was the likely cause of: https://bugzilla.redhat.com/show_bug.cgi?id=173153 Cc: stable@kernel.org Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
Fix an error introduced in dm-table-rework-reference-counting.patch. When there is failure after table initialization, we need to use dm_table_destroy, not dm_table_put, to free the table. dm_table_put may be used only after dm_table_get. Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com> Signed-off-by:
Jonathan Brassow <jbrassow@redhat.com> Reviewed-by:
-
Milan Broz authored
When renaming a mapped device validate the length of the new name. The rename ioctl accepted any correctly-terminated string enclosed within the data passed from userspace. The other ioctls enforce a size limit of DM_NAME_LEN. If the name is changed and becomes longer than that, the device can no longer be addressed by name. Fix it by properly checking for device name length (including terminating zero). Cc: stable@kernel.org Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits) r8169: revert "r8169: read MAC address from EEPROM on init (2nd attempt)" r8169: use hardware auto-padding. igb: remove ASPM L0s workaround netxen: remove old flash check. mv643xx_eth: fix unicast address filter corruption on mtu change xfrm: Fix xfrm_state_find() wrt. wildcard source address. emac: Fix clock control for 405EX and 405EXr chips ixgbe: fix multiple unicast address support via-velocity: Fix DMA mapping length errors on transmit. qlge: bugfix: Pad outbound frames smaller than 60 bytes. qlge: bugfix: Move netif_napi_del() to common call point. qlge: bugfix: Tell hw to strip vlan header. qlge: bugfix: Increase filter on inbound csum. dnet: replace obsolete *netif_rx_* functions with *napi_* net: Add be2net driver. dnet: Fix warnings on 64-bit. dnet: Dave DNET ethernet controller driver (updated) ipv6: Fix BUG when disabled ipv6 module is unloaded bnx2x: Using DMAE to initialize the chip bnx2x: Casting page alignment ...
-
Rusty Russell authored
Impact: help prevent extinction of species The Tasmanian Devil is a shy iconic Australian creature named for its spine-chilling screech. It is threatened with extinction due to a scientifically interesting but horrific transmissible facial cancer. This one is standing in for Tux for one release using the far less-known Devil Facial Tux Disguise. Save The Tasmanian Devil http://tassiedevil.com.auSigned-off-by:
Linux.conf.au Hobart Team <contact@marchsouth.org> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Zhang Le authored
filp->f_pos only get updated at the end of the function. Thus d_off of those dirents who are in the middle will be 0, and this will cause a problem in glibc's readdir implementation, specifically endless loop. Because when overflow occurs, f_pos will be set to next dirent to read, however it will be 0, unless the next one is the last one. So it will start over again and again. There is a sample program in man 2 gendents. This is the output of the program running on a multithread program's task dir before this patch is applied: $ ./a.out /proc/3807/task --------------- nread=128 --------------- i-node# file type d_reclen d_off d_name 506442 directory 16 1 . 506441 directory 16 0 .. 506443 directory 16 0 3807 506444 directory 16 0 3809 506445 directory 16 0 3812 506446 directory 16 0 3861 506447 directory 16 0 3862 506448 directory 16 8 3863 This is the output after this patch is applied $ ./a.out /proc/3807/task --------------- nread=128 --------------- i-node# file type d_reclen d_off d_name 506442 directory 16 1 . 506441 directory 16 2 .. 506443 directory 16 3 3807 506444 directory 16 4 3809 506445 directory 16 5 3812 506446 directory 16 6 3861 506447 directory 16 7 3862 506448 directory 16 8 3863 Signed-off-by:Zhang Le <r0bertz@gentoo.org> Acked-by:
Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
-
Len Brown authored
-
Roel Kluin authored
include/linux/pci-acpi.h:74: typedef u32 acpi_status; result is unsigned, so an error returned by acpi_bus_register_driver() will not be noticed. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
Len Brown <len.brown@intel.com>
-
Mathieu Chouquet-Stringer authored
Looking at the source, there seems to be a missing * to match my DMI string. I mean for newer IBM and Lenovo's laptops you match either one of the following: MODULE_ALIAS("dmi:bvnIBM:*:svnIBM:*:pvrThinkPad*:rvnIBM:*"); MODULE_ALIAS("dmi:bvnLENOVO:*:svnLENOVO:*:pvrThinkPad*:rvnLENOVO:*"); While for older Thinkpads, you do this (for instance): IBM_BIOS_MODULE_ALIAS("1[0,3,6,8,A-G,I,K,M-P,S,T]"); with IBM_BIOS_MODULE_ALIAS being MODULE_ALIAS("dmi:bvnIBM:bvr" __type "ET??WW") Note there's no * terminating the string. As result, udev doesn't load anything because modprobe cannot find anything matching this (my machine actually): udevtest: run: '/sbin/modprobe dmi:bvnIBM:bvr1IET71WW(2.10):bd06/16/2006:svnIBM:pn236621U:pvrNotAv Signed-off-by:Mathieu Chouquet-Stringer <mchouque@free.fr> Acked-by:
Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by:
-
Carlos Corbacho authored
This driver has been around and used long enough that we can drop the 'experimental'. Signed-off-by:
Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by:
-
Carlos Corbacho authored
ACPI-WMI isn't experimental anymore, and there are other drivers that now depend on it that aren't either. Signed-off-by:
-
Dan Carpenter authored
This is acer_rfkill_exit() from drivers/platform/x86/acer-wmi.c. The code frees wireless_rfkill->data again instead of bluetooth_rfkill->data. This was found using a code checker (http://repo.or.cz/w/smatch.git/). Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
-
Corentin Chary authored
"I hate `select' and will gleefully leap on any s/select/depends/ patch, whether it works or not :)" Andrew Morton select INPUT is not needed here, because if someone doesn't want INPUT, he won't want these drivers either. Signed-off-by:
Corentin Chary <corentincj@iksaif.net> Signed-off-by:
-
