Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2017-10-10

This series contains updates to e1000e and igb.

Benjamin Poirier provides several fixes for e1000e, starting with a
correction to the return status which was always returning success even
if it was not successful.  Fixed code comments to reflect the actual
code behavior.  Fixed the conditional test for the correct return
value.  Fixed a potential race condition reported by Lennart Sorensen,
where the single flag get_link_status is used to signal two different
states.

Sasha fixes a buffer overrun for i219 devices, where the chipset had
reduced the round-trip latency for the LAN controller DMA accesses
which in some high performance cases caused a buffer overrun while
processing the DMA transactions.

Willem de Bruijn changes the default behavior of e1000e to use the
burst mode settings by default unless the user specifies the
receive interrupt delay (RxIntDelay).

Florian Fainelli updates the driver to differentiate between when
e1000e_put_txbuf() is called from normal reclamation or when a
DMA mapping failure to make the driver more "drop monitor friendly".

Christophe JAILLET fixes a potential NULL pointer dereference by
properly returning -ENOMEM on memory allocation failures.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We can now piggyback error strings to userspace via extended acks
rather than using printk.

Before:
bridge fdb add 01:02:03:04:05:06 dev br0 vlan 4095
RTNETLINK answers: Invalid argument

After:
bridge fdb add 01:02:03:04:05:06 dev br0 vlan 4095
Error: invalid vlan id.

v3: drop 'RTM_' prefixes, suggested by David Ahern, they
are not useful, the add/del in bridge command line is enough.

Also reword error in response to malformed/bad vlan id attribute
size.

Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

exercise RTM_GETNETCONF call path for unspec, inet and inet6
families, they are DOIT_UNLOCKED candidates.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
mlx4_en num of rings

This patchset from Inbar contains changes to rings control
to the mlx4 Eth driver.

Patches 1 and 2 limit the number of rings to the number of CPUs.
Patch 3 removes a limitation in logic of default number of RX rings.

Series generated against net-next commit:
812b5ca7 Add a driver for Renesas uPD60620 and uPD60620A PHYs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove limitation of netif_get_num_default_rss_queues()
from logic of RX rings default number.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Limit the number of RX rings by the number of cores
in the system.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Limit the number of TX rings per UP by the number of cores
in the system.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lipeng says:

====================
Support set_ringparam and {set|get}_rxnfc ethtool commands

1, Patch [1/5,2/5] add support for ethtool ops set_ringparam
   (ethtool -G) and fix related bug.
2, Patch [3/5,4/5, 5/5] add support for ethtool ops
   set_rxnfc/get_rxnfc (-n/-N) and fix related bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix the ring count for ETHTOOL_GRXRINGS. Ring count
not TC size should be return for command "ethtool -n ethx".
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add support for ethtool's ETHTOOL_GRXFH in hns3_get_rxnfc().
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch supports the ethtool's set_rxnfc().
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch supports the ethtool's set_ringparam().
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the ring index in hns3_fini_ring.
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 0x50aa and 0x50ab T5 device id's.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for new flash parts identification, and
also cleanup the flash Part identifying and decoding
code.

Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix BUG() calls to use BUG_ON(conditional) macros.

This was found using make coccicheck M=net/core on linux next
tag next-2017092
Signed-off-by: Tim Hansen <devtimhansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
bpf: get rid of global verifier state and reuse instruction printer

This set started off as simple extraction of eBPF verifier's instruction
printer into a separate file but evolved into removal of global state.
The purpose of moving instruction printing code is to be able to reuse it
from the bpftool.

As far as the global verifier lock goes, this set removes the global
variables relating to the log buffer, makes the one-time init done
by bpf_get_skb_set_tunnel_proto() not depend on any external locking,
and performs verifier log writeback as data is produced removing the need
for allocating a potentially large temporary buffer.

The final step of actually removing the verifier lock is left to someone
more competent and self-confident :)

Note that struct bpf_verifier_env is just 40B under two pages now,
we should probably switch to vzalloc() when it's expanded again...

v2:
 - add a selftest;
 - use env buffer and flush on every print (Alexei);
 - handle kernel log allocation failures (Daniel);
 - put the env log members into a struct (Daniel).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Verifier log buffer can be quite large (up to 16MB currently).
As Eric Dumazet points out if we allow multiple verification
requests to proceed simultaneously, malicious user may use the
verifier as a way of allocating large amounts of unswappable
memory to OOM the host.

Switch to a strategy of allocating a smaller buffer (1024B)
and writing it out into the user buffer after every print.

While at it remove the old BUG_ON().

This is in preparation of the global verifier lock removal.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf_skb_set_tunnel_*() functions require allocation of per-cpu
metadata_dst.  The allocation happens upon verification of the
first program using those helpers.  In preparation for removing
the verifier lock, use cmpxchg() to make sure we only allocate
the metadata_dsts once.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compile the instruction printer from kernel/bpf and use it
for disassembling "translated" eBPF code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate the instruction printing into a standalone source file.
This way sneaky code from tools/ can compile it in directly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The biggest piece of global state protected by the verifier lock
is the verifier_log.  Move that log to struct bpf_verifier_env.
struct bpf_verifier_env has to be passed now to all invocations
of verbose().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put the loose log_* variables into a structure.  This will make
it simpler to remove the global verifier state in following patches.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test for verifier log handling.  Check bad attr combinations
but focus on cases when log is truncated.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The use of the | operator always leads to true which looks rather
suspect to me. Fix this by using & instead to just check the
RTF_CACHE entry bit.

Detected by CoverityScan, CID#1457734, #1457747 ("Wrong operator used")

Fixes: 35732d01 ("ipv6: introduce a hash table to store dst cache")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently rt6_ex is being dereferenced before it is null checked
hence there is a possible null dereference bug. Fix this by only
dereferencing rt6_ex after it has been null checked.

Detected by CoverityScan, CID#1457749 ("Dereference before null check")

Fixes: 81eb8447 ("ipv6: take care of rt6_stats")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check memory allocation failures and return -ENOMEM in such cases, as
already done for other memory allocations in this function.

This avoids NULL pointers dereference.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com
Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e_put_txbuf() can be called from normal reclamation path as well as
when a DMA mapping failure, so we need to differentiate these two cases
when freeing SKBs to be drop monitor friendly. e1000e_tx_hwtstamp_work()
and e1000_remove() are processing TX timestamped SKBs and those should
not be accounted as drops either.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Devices that support FLAG2_DMA_BURST have different default values
for RDTR and RADV. Apply burst mode default settings only when no
explicit value was passed at module load.

The RDTR default is zero. If the module is loaded for low latency
operation with RxIntDelay=0, do not override this value with a burst
default of 32.

Move the decision to apply burst values earlier, where explicitly
initialized module variables can be distinguished from defaults.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Intel® 100/200 Series Chipset platforms reduced the round-trip
latency for the LAN Controller DMA accesses, causing in some high
performance cases a buffer overrun while the I219 LAN Connected
Device is processing the DMA transactions. I219LM and I219V devices
can fall into unrecovered Tx hang under very stressfully UDP traffic
and multiple reconnection of Ethernet cable. This Tx hang of the LAN
Controller is only recovered if the system is rebooted. Slightly slow
down DMA access by reducing the number of outstanding requests.
This workaround could have an impact on TCP traffic performance
on the platform. Disabling TSO eliminates performance loss for TCP
traffic without a noticeable impact on CPU performance.

Please, refer to I218/I219 specification update:
https://www.intel.com/content/www/us/en/embedded/products/networking/
ethernet-connection-i218-family-documentation.html
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.

This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.

Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59 ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Lennart reported the following race condition:

\ e1000_watchdog_task
    \ e1000e_has_link
        \ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
            /* link is up */
            mac->get_link_status = false;

                            /* interrupt */
                            \ e1000_msix_other
                                hw->mac.get_link_status = true;

        link_active = !hw->mac.get_link_status
        /* link_active is false, wrongly */

This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.

Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Reading e1000e_check_for_copper_link() shows that get_link_status is set to
false after link has been detected. Therefore, it stays TRUE until then.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vhost-net has a hard limit on the number of zerocopy skbs in flight.
When reached, transmission stalls. Stalls cause latency, as well as
head-of-line blocking of other flows that do not use zerocopy.

Instead of stalling, revert to copy-based transmission.

Tested by sending two udp flows from guest to host, one with payload
of VHOST_GOODCOPY_LEN, the other too small for zerocopy (1B). The
large flow is redirected to a netem instance with 1MBps rate limit
and deep 1000 entry queue.

  modprobe ifb
  ip link set dev ifb0 up
  tc qdisc add dev ifb0 root netem limit 1000 rate 1MBit

  tc qdisc add dev tap0 ingress
  tc filter add dev tap0 parent ffff: protocol ip \
      u32 match ip dport 8000 0xffff \
      action mirred egress redirect dev ifb0

Before the delay, both flows process around 80K pps. With the delay,
before this patch, both process around 400. After this patch, the
large flow is still rate limited, while the small reverts to its
original rate. See also discussion in the first link, below.

Without rate limiting, {1, 10, 100}x TCP_STREAM tests continued to
send at 100% zerocopy.

The limit in vhost_exceeds_maxpend must be carefully chosen. With
vq->num >> 1, the flows remain correlated. This value happens to
correspond to VHOST_MAX_PENDING for vq->num == 256. Allow smaller
fractions and ensure correctness also for much smaller values of
vq->num, by testing the min() of both explicitly. See also the
discussion in the second link below.

Changes
  v1 -> v2
    - replaced min with typed min_t
    - avoid unnecessary whitespace change

Link:http://lkml.kernel.org/r/CAF=yD-+Wk9sc9dXMUq1+x_hh=3ThTXa6BnZkygP3tgVpjbp93g@mail.gmail.com
Link:http://lkml.kernel.org/r/20170819064129.27272-1-den@klaipeden.comSigned-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add erspan netlink interface for OVS.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch the DO_ONCE() macro from the deprecated jump label API to the new
one.  The new one is more readable, and for DO_ONCE() it also makes the
generated code more icache-friendly: now the one-time initialization
code is placed out-of-line at the jump target, rather than at the inline
fallthrough case.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>