Add bus protection for reset controller.

Signed-off-by: Trevor Wu <trevor.wu@mediatek.com
Link: https://lore.kernel.org/r/20230510035526.18137-7-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org

There is no benefit to separate two components for AFE, so DAI driver
registration is moved to dev_snd_soc_register_component to merge these
two components.

Signed-off-by: Trevor Wu <trevor.wu@mediatek.com
Link: https://lore.kernel.org/r/20230510035526.18137-6-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org

Currently, APLL is only used in ETDM module, so APLL and APLL tuner
don't need to be enabled when AFE is used. Integrate APLL control into
ETDM DAPM routes, so that APLL can be enabled when it is really required.

Signed-off-by: Trevor Wu <trevor.wu@mediatek.com
Link: https://lore.kernel.org/r/20230510035526.18137-5-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org

Replace register controls in snd_soc_dai_ops with snd_soc_dapm_widgets.
startup, shutdown and trigger ops are removed, and create DAPM_SUPPLY
to handle mclk, clock gating and etdm enabling. Additionally, mclk setup
sequence is also updated because of new supply enabling sequence.

Signed-off-by: Trevor Wu <trevor.wu@mediatek.com
Link: https://lore.kernel.org/r/20230510035526.18137-4-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org

User can configures slot number of TDM mode via set_tdm_slot callback.

Signed-off-by: Trevor Wu <trevor.wu@mediatek.com
Link: https://lore.kernel.org/r/20230510035526.18137-3-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org

AUDIO_HIRES is not required in MT8188. Because top_audio_h is disabled
when hires clock is not used, set_parent is a redundant operation.

Signed-off-by: Trevor Wu <trevor.wu@mediatek.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com
Link: https://lore.kernel.org/r/20230510035526.18137-2-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org

Avoid tripping over fixed issues in CI.

Merge series from Martin Povišer <povik+lin@cutebit.org>:

Analog Devices SSM3515 is a simple speaker amp that Apple is
using in their 2021 iMacs, possibly elsewhere.

This model requires an additional detection quirk to enable the internal microphone.

Signed-off-by: Rsplwe <i@rsplwe.com
Link: https://lore.kernel.org/r/tencent_3C6819728B6704C39A864762FB0BB77DF509@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org

Convert the NAU8825 audio CODEC bindings to DT schema.

Signed-off-by: David Lin <CTLIN0@nuvoton.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230511113607.595184-1-CTLIN0@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org

The Analog Devices' SSM3515 is a mono audio amplifier with digital
input, equipped on Apple's 2021 iMacs. Add an ASoC driver for it, and
register both the driver code and schema in MAINTAINERS.

Signed-off-by: Martin Povišer <povik+lin@cutebit.org
Link: https://lore.kernel.org/r/20230511150546.8499-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org

Add a DT schema for the SSM3515 amp by Analog Devices. It's a simple
mono amplifier with digital input.

Signed-off-by: Martin Povišer <povik+lin@cutebit.org
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230511150546.8499-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org

Apply a workaround for what appears to be a hardware quirk.

The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.

This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).

Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
        i2cset -y 0 0x1a $(($1*2)) $2
}

For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x87 # out, dac
  ssmset 0x06 0x07 # chip
  OK

  (disable MCLK)
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x1f # chip
  ssmset 0x06 0x07 # out, dac
  (enable MCLK)
  OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x1f # chip
  ssmset 0x06 0x07 # out, dac
  NOT OK

  ssmset 0x06 0x1f # chip
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # out, dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x0f # chip, out
  ssmset 0x06 0x07 # dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x17 # chip, dac
  ssmset 0x06 0x07 # out
  NOT OK

For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  OK

  (disable MCLK)
  ssmset 0x09 0x01 # core
  ssmset 0x06 0x07 # chip, out, dac
  (enable MCLK after reset)
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x17 # chip, dac
  NOT OK

  ssmset 0x09 0x01 # core
  ssmset 0x06 0x0f # chip, out
  NOT OK

  ssmset 0x06 0x07 # chip, out, dac
  NOT OK

Signed-off-by: Paweł Anikiel <pan@semihalf.com
Link: https://lore.kernel.org/r/20230508113037.137627-8-pan@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org

Merge series from Srinivas Kandagatla <srinivas.kandagatla@linaro.org>:

This patchset adds support to displayport on AudioReach.
Patches are tested on X13s with two display ports.

The audio controller in the X1000 is similar to the JZ47xx SoCs.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230509124238.195191-2-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org

The X1000's AIC is similar to the AIC found on other Ingenic SoCs.
It has symmetric playback/capture rates like the JZ4740, but more
flexible clocking when outputting the system or bit clocks.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com
Link: https://lore.kernel.org/r/20230509124238.195191-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org

This patch adds support to q6apm lpass display port dais. This support
is required to get DP audio on x13s.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org
Link: https://lore.kernel.org/r/20230509112202.21471-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org

Existing code base only supports one display port, this patch adds
support upto 8 display ports. This support is required to allow platforms
like X13s which have 3 display ports, and some of the Qualcomm SoCs
there are upto 7 Display ports.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org
Link: https://lore.kernel.org/r/20230509112202.21471-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org

Add support for DISPLAY PORT SINK module and associated configuration.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org
Link: https://lore.kernel.org/r/20230509112202.21471-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org

move hdmi/dp channel allocation to a common function
q6dsp_get_channel_allocation() so that we can reuse this across
q6afe and q6apm drivers.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org
Link: https://lore.kernel.org/r/20230509112202.21471-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org

A bunch of TI's codecs have binding schemas which force #sound-dai-cells
to one despite those codecs only having a single DAI. Allow for bindings
with zero DAI cells and deprecate the former non-zero value.

Signed-off-by: Martin Povišer <povik+lin@cutebit.org
Link: https://lore.kernel.org/r/20230509153412.62847-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org

When the CPU supplies bit/frame clocks, the system clock (clk_i2s)
is divided to produce the bit clock. This is a simple 1/N divider
with a fairly limited range, so for a given system clock frequency
only a few sample rates can be produced. Usually a wider range of
sample rates is supported by varying the system clock frequency.

The old calculation method was not very robust and could easily
produce the wrong clock rate, especially with non-standard rates.
For example, if the system clock is 1.99x the target bit clock
rate, the divider would be calculated as 1 instead of the more
accurate 2.

Instead, use a more accurate method that considers two adjacent
divider settings and selects the one that produces the least error
versus the requested rate. If the error is 5% or higher then the
rate setting is rejected to prevent garbled audio.

Skip divider calculation when the codec is supplying both the bit
and frame clock; in that case, the divider outputs are unused and
we don't want to constrain the sample rate.

Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com
Link: https://lore.kernel.org/r/20230509125134.208129-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org

Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:

Many ASoC drivers are using dummy DAI.
I have 2 concern about it. 1st one is there is no guarantee that local
strings ("snd-soc-dummy-dai",  "snd-soc-dummy") are kept until the card
was binded if it was added at subfunction.
2nd one is we can use common snd_soc_dai_link_component for it.
This patch-set adds common asoc_dummy_dlc, and use it.

This is the initial codec driver for rt722-sdca.

Signed-off-by: Jack Yu <jack.yu@realtek.com
Link: https://lore.kernel.org/r/20230421030116.26245-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org

Merge series from AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:

This series performs some cleanups for mainly MT8195 and switches
both MT8195 and MT8186's SOF driver to the snd_sof_ipc_process_reply()
helper.

Check substream and runtime variables before assigning.

Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com
Link: https://lore.kernel.org/r/20230508070510.6100-1-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org

There is error message when defer probe happens:

fsl-micfil-dai 30ca0000.micfil: Unbalanced pm_runtime_enable!

Fix the error handler with pm_runtime_enable and add
fsl_micfil_remove() for pm_runtime_disable.

Fixes: 47a70e6f ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com
Link: https://lore.kernel.org/r/1683540996-6136-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org

On slow CPU (FPGA/QEMU emulated) printing overrun messages from
interrupt handler to uart console may leads to more overrun errors.
So use dev_err_ratelimited to limit the number of error messages.

Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru
Link: https://lore.kernel.org/r/20230505062820.21840-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org

Add pang12 quirk to enable the internal microphone.

Signed-off-by: Jeremy Soller <jeremy@system76.com
Signed-off-by: Tim Crawford <tcrawford@system76.com
Link: https://lore.kernel.org/r/20230505161458.19676-1-tcrawford@system76.com
Signed-off-by: Mark Brown <broonie@kernel.org

On i.MX8MP, the sai MCLK is bound with TX/RX enable bit,
which means the TX/RE enable bit need to be enabled then
MCLK can be output on PAD.

Some codec (for example: WM8962) needs the MCLK output
earlier, otherwise there will be issue for codec
configuration.

Add new soc data "mclk_with_tere" for this platform and
enable the MCLK output in startup stage.

As "mclk_with_tere" only applied to i.MX8MP, currently
The soc data is shared with i.MX8MN, so need to add
an i.MX8MN own soc data with "mclk_with_tere" disabled.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com
Link: https://lore.kernel.org/r/1683273322-2525-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org

./sound/soc/codecs/wcd938x-sdw.c:1274:2-3: Unneeded semicolon

Reported-by: Abaci Robot <abaci@linux.alibaba.com
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4862
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com
Link: https://lore.kernel.org/r/20230505004538.70270-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org

Convert the NAU8540 audio CODEC bindings to DT schema

Signed-off-by: Anup Sharma <anupnewsmail@gmail.com

Changes:
V1 -> V2: Adhere to the correct procedure by including the maintainer's name.
          Drop Mark from maintainer.

Link: https://lore.kernel.org/r/ZFYxWVdE9YkMKvXv@yoga
Signed-off-by: Mark Brown <broonie@kernel.org

Instead of a busy waiting while loop using udelay in
acp63_power_on and acp63_reset functions use readl_poll_timeout
function to check the condition.

Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com
Link: https://lore.kernel.org/r/20230426122219.3745586-2-Syed.SabaKareem@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org

Instead of acp63_readl() and acp63_writel() wrappers
readl and writel functions can be used directly.
Remove acp63_readl() and acp63_writel() wrappers.

Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com
Link: https://lore.kernel.org/r/20230426122219.3745586-1-Syed.SabaKareem@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org

After commit b8a1a4cd ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f4 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Link: https://lore.kernel.org/r/20230425095716.331419-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org

The most recent changes to ASoC, such as new module parameters, date to the
year 2023. Update copyright statement accordingly.

Signed-off-by: Carlos Bilbao <carlos.bilbao@amd.com
Link: https://lore.kernel.org/r/20230420180212.3101178-1-carlos.bilbao@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org

The COMP1_TX_WORDSIZE_0/COMP2_RX_WORDSIZE_0 fields in the comp
registers indicate the maximum wordsize supported. DWC I2S controller
can operate with any smaller wordsize. So extend the formats to let
I2S to operate in any allowed modes.

Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru
Link: https://lore.kernel.org/r/20230505053521.18233-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org

regmap has introduced a maple tree based register cache which makes use of
this more advanced data structure which has been added to the kernel
recently. Maple trees are much flatter than rbtrees, meaning that they do
not grow to such depths when the register map is sparse which makes access
a bit more efficient. The maple tree cache type is still a bit of a work
in progress but should be effective for some devices already.

RT5682 seems like a good candidate for maple tree. It only supports single
register read/write operations so will gain minimal benefit from storing
the register data in device native format like rbtree does (none for
SoundWire) and has some sparsity in the register map which is a good fit
for maple tree.

Convert to use maple tree. There should be little if any visible difference
at runtime.

Signed-off-by: Mark Brown <broonie@kernel.org
Link: https://lore.kernel.org/r/20230419-asoc-rt5682-maple-v1-1-ed40369c9099@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org

Another batch of dropping unneeded quotes on $id and $schema which were
missed in the last round. Once all these are fixed, checking for this can
be enabled in yamllint.

Signed-off-by: Rob Herring <robh@kernel.org
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230421214810.1811962-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org

SC7180 Trogdor sound cards come with multiple audio amplifiers, so allow
up to four of them to fix dtbs_check warnings like:

  sc7180-trogdor-homestar-r3.dtb: sound: dai-link@1:codec:sound-dai: [[275], [276], [277], [278]] is too long

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Acked-by: Conor Dooley <conor.dooley@microchip.com
Link: https://lore.kernel.org/r/20230507174543.264987-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org