- 09 Mar, 2019 10 commits
-
-
he, bo authored
On some laptops, kxcjk1013 is powered off when system enters S3. We need restore the range regiter during resume. Otherwise, the sensor doesn't work properly after S3. Signed-off-by:
he, bo <bo.he@intel.com> Signed-off-by:
Chen, Hu <hu1.chen@intel.com> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Mike Looijmans authored
The SPI interface implementation was completely broken. When using the SPI interface, there are only 7 address bits, the upper bit is controlled by a page select register. The core needs access to both ranges, so implement register read/write for both regions. The regmap paging functionality didn't agree with a register that needs to be read and modified, so I implemented a custom paging algorithm. This fixes that the device wouldn't even probe in SPI mode. The SPI interface then isn't different from I2C, merged them into the core, and the I2C/SPI named registers are no longer needed. Implemented register value caching for the registers to reduce the I2C/SPI data transfers considerably. The calibration set reads as all zeroes until some undefined point in time, and I couldn't determine what makes it valid. The datasheet mentions these registers but does not provide any hints on when they become valid, and they aren't even enumerated in the memory map. So check the calibration and retry reading it from the device after each measurement until it provides something valid. Despite the size this is suitable for a stable backport given that it seems the SPI support never worked. Signed-off-by:
Mike Looijmans <mike.looijmans@topic.nl> Fixes: 1b3bd859 ("iio: chemical: Add support for Bosch BME680 sensor"); Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Mike Looijmans authored
The standard unit for temperature is millidegrees Celcius. Adapt the driver to report in millidegrees instead of degrees. Signed-off-by:
Mike Looijmans <mike.looijmans@topic.nl> Fixes: 1b3bd859 ("iio: chemical: Add support for Bosch BME680 sensor"); Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Jonathan Cameron authored
I clearly messed up applying this patch. Not sure how but the entire Kconfig block is missing. This patch puts it back as it was in the original patch. Reported-by:
Andreas Brauchli <a.brauchli@elementarea.net> Fixes: ce514124 ("iio: chemical: sgp30: Support Sensirion SGP30/SGPC3 sensors") Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Georg Ottinger authored
Having a brief look at at91_adc_read_raw() it is obvious that in the case of a timeout the setting of AT91_ADC_CHDR and AT91_ADC_IDR registers is omitted. If 2 different channels are queried we can end up with a situation where two interrupts are enabled, but only one interrupt is cleared in the interrupt handler. Resulting in a interrupt loop and a system hang. Signed-off-by:
Georg Ottinger <g.ottinger@abatec.at> Acked-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Sergey Larin authored
According to the datasheet, the last bit of CHIP_ID register controls I2C bus, and the first one is unused. Handle this correctly. Note that there are chips out there that have a value such that the id check currently fails. Signed-off-by:
Sergey Larin <cerg2010cerg2010@mail.ru> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Lars-Peter Clausen authored
The trialmask is expected to have all bits set to 0 after allocation. Currently kmalloc_array() is used which does not zero the memory and so random bits are set. This results in random channels being enabled when they shouldn't. Replace kmalloc_array() with kcalloc() which has the same interface but zeros the memory. Note the fix is actually required earlier than the below fixes tag, but will require a manual backport due to move from kmalloc to kmalloc_array. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Fixes commit 057ac1ac ("iio: Use kmalloc_array() in iio_scan_mask_set()"). Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Mircea Caprioru authored
This patch fixes the differential channels addresses for the ad7193. Signed-off-by:
Mircea Caprioru <mircea.caprioru@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Mike Looijmans authored
Standard unit for temperature is millidegrees Celcius, whereas this driver was reporting in degrees. Fix the scale factor in the driver. Signed-off-by:
Mike Looijmans <mike.looijmans@topic.nl> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Leonard Pollak authored
This patch fixes an obvious typo, which will cause erroneously returning the Peak Voltage instead of the Peak Current. Signed-off-by:
Leonard Pollak <leonardp@tr-host.de> Cc: <Stable@vger.kernel.org> Acked-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 08 Mar, 2019 30 commits
-
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull io_uring IO interface from Jens Axboe: "Second attempt at adding the io_uring interface. Since the first one, we've added basic unit testing of the three system calls, that resides in liburing like the other unit tests that we have so far. It'll take a while to get full coverage of it, but we're working towards it. I've also added two basic test programs to tools/io_uring. One uses the raw interface and has support for all the various features that io_uring supports outside of standard IO, like fixed files, fixed IO buffers, and polled IO. The other uses the liburing API, and is a simplified version of cp(1). This adds support for a new IO interface, io_uring. io_uring allows an application to communicate with the kernel through two rings, the submission queue (SQ) and completion queue (CQ) ring. This allows for very efficient handling of IOs, see the v5 posting for some basic numbers: https://lore.kernel.org/linux-block/20190116175003.17880-1-axboe@kernel.dk/ Outside of just efficiency, the interface is also flexible and extendable, and allows for future use cases like the upcoming NVMe key-value store API, networked IO, and so on. It also supports async buffered IO, something that we've always failed to support in the kernel. Outside of basic IO features, it supports async polled IO as well. This particular feature has already been tested at Facebook months ago for flash storage boxes, with 25-33% improvements. It makes polled IO actually useful for real world use cases, where even basic flash sees a nice win in terms of efficiency, latency, and performance. These boxes were IOPS bound before, now they are not. This series adds three new system calls. One for setting up an io_uring instance (io_uring_setup(2)), one for submitting/completing IO (io_uring_enter(2)), and one for aux functions like registrating file sets, buffers, etc (io_uring_register(2)). Through the help of Arnd, I've coordinated the syscall numbers so merge on that front should be painless. Jon did a writeup of the interface a while back, which (except for minor details that have been tweaked) is still accurate. Find that here: https://lwn.net/Articles/776703/ Huge thanks to Al Viro for helping getting the reference cycle code correct, and to Jann Horn for his extensive reviews focused on both security and bugs in general. There's a userspace library that provides basic functionality for applications that don't need or want to care about how to fiddle with the rings directly. It has helpers to allow applications to easily set up an io_uring instance, and submit/complete IO through it without knowing about the intricacies of the rings. It also includes man pages (thanks to Jeff Moyer), and will continue to grow support helper functions and features as time progresses. Find it here: git://git.kernel.dk/liburing Fio has full support for the raw interface, both in the form of an IO engine (io_uring), but also with a small test application (t/io_uring) that can exercise and benchmark the interface" * tag 'io_uring-2019-03-06' of git://git.kernel.dk/linux-block: io_uring: add a few test tools io_uring: allow workqueue item to handle multiple buffered requests io_uring: add support for IORING_OP_POLL io_uring: add io_kiocb ref count io_uring: add submission polling io_uring: add file set registration net: split out functions related to registering inflight socket files io_uring: add support for pre-mapped user IO buffers block: implement bio helper to add iter bvec pages to bio io_uring: batch io_kiocb allocation io_uring: use fget/fput_many() for file references fs: add fget_many() and fput_many() io_uring: support for IO polling io_uring: add fsync support Add io_uring IO interface
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block layer updates from Jens Axboe: "Not a huge amount of changes in this round, the biggest one is that we finally have Mings multi-page bvec support merged. Apart from that, this pull request contains: - Small series that avoids quiescing the queue for sysfs changes that match what we currently have (Aleksei) - Series of bcache fixes (via Coly) - Series of lightnvm fixes (via Mathias) - NVMe pull request from Christoph. Nothing major, just SPDX/license cleanups, RR mp policy (Hannes), and little fixes (Bart, Chaitanya). - BFQ series (Paolo) - Save blk-mq cpu -> hw queue mapping, removing a pointer indirection for the fast path (Jianchao) - fops->iopoll() added for async IO polling, this is a feature that the upcoming io_uring interface will use (Christoph, me) - Partition scan loop fixes (Dongli) - mtip32xx conversion from managed resource API (Christoph) - cdrom registration race fix (Guenter) - MD pull from Song, two minor fixes. - Various documentation fixes (Marcos) - Multi-page bvec feature. This brings a lot of nice improvements with it, like more efficient splitting, larger IOs can be supported without growing the bvec table size, and so on. (Ming) - Various little fixes to core and drivers" * tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits) block: fix updating bio's front segment size block: Replace function name in string with __func__ nbd: propagate genlmsg_reply return code floppy: remove set but not used variable 'q' null_blk: fix checking for REQ_FUA block: fix NULL pointer dereference in register_disk fs: fix guard_bio_eod to check for real EOD errors blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map block: optimize bvec iteration in bvec_iter_advance block: introduce mp_bvec_for_each_page() for iterating over page block: optimize blk_bio_segment_split for single-page bvec block: optimize __blk_segment_map_sg() for single-page bvec block: introduce bvec_nth_page() iomap: wire up the iopoll method block: add bio_set_polled() helper block: wire up block device iopoll method fs: add an iopoll method to struct file_operations loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part() loop: do not print warn message if partition scan is successful block: bounce: make sure that bvec table is updated ...
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull libata updates from Jens Axboe: "Pretty quiet round: a few small fixes, comment typo, and most notably a low level driver for the PATA Buddha controller" * tag 'for-5.1/libata-20190301' of git://git.kernel.dk/linux-block: ata: libahci: Only warn for AHCI_HFLAG_MULTI_MSI set when genuine custom irq handler implemented libata: fix a typo in comment ata: macio: Use of_node_name_eq for node name comparisons ata: pata_samsung_cf: simplify getting .driver_data ata: pata_platform: Add IRQF_SHARED to IRQ flags ata: pata_of_platform: Allow to use 16-bit wide data transfer ata: add Buddha PATA controller driver
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpioLinus Torvalds authored
Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v5.1 cycle: Core changes: - The big change this time around is the irqchip handling in the qualcomm pin controllers, closely coupled with the gpiochip. This rework, in a classic fall-between-the-chairs fashion has been sidestepped for too long. The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms have been rewritten to use hierarchical irqchip. This creates the base from which I intend to gradually pull support for hierarchical irqchips into the gpiolib irqchip helpers to cut down on duplicate code. We have too many hacks in the kernel because people have been working around the missing hierarchical irqchip for years, and once it was there, noone understood it for a while. We are now slowly adapting to using it. This is why this pull requests include changes to MFD, SPMI, IRQchip core and some ARM Device Trees pertaining to the Qualcomm chip family. Since Qualcomm have so many chips and such large deployments it is paramount that this platform gets this right, and now it (hopefully) does. - Core support for pull-up and pull-down configuration, also from the device tree. When a simple GPIO chip supports an "off or on" pull-up or pull-down resistor, we provide a way to set this up using machine descriptors or device tree. If more elaborate control of pull up/down (such as resistance shunt setting) is required, drivers should be phased over to use pin control. We do not yet provide a userspace ABI for this pull up-down setting but I suspect the makers are going to ask for it soon enough. PCA953x is the first user of this new API. - The GPIO mockup driver has been revamped after some discussion improving the IRQ simulator in the process. The idea is to make it possible to use the mockup for both testing and virtual prototyping, e.g. when you do not yet have a GPIO expander to play with but really want to get something to develop code around before hardware is available. It's neat. The blackbox testing usecase is currently making its way into kernelci. - ACPI GPIO core preserves non direction flags when updating flags. - A new device core helper for devm_platform_ioremap_resource() is funneled through the GPIO tree with Greg's ACK. New drivers: - TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O) - Gateworks PLD GPIO driver (vaccumed up from OpenWrt) - AMD G-Series PCH (Platform Controller Hub) GPIO driver. - Fintek F81804 & F81966 subvariants. - PCA953x now supports NXP PCAL6416. Driver improvements: - IRQ support on the Nintendo Wii (Hollywood) GPIO. - get_direction() support for the MVEBU driver. - Set the right output level on SAMA5D2. - Drop the unused irq trigger setting on the Spreadtrum driver. - Wakeup support for PCA953x. - A slew of cleanups in the various Intel drivers" * tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits) gpio: gpio-omap: fix level interrupt idling gpio: amd-fch: Set proper output level for direction_output x86: apuv2: remove unused variable gpio: pca953x: Use PCA_LATCH_INT platform/x86: fix PCENGINES_APU2 Kconfig warning gpio: pca953x: Fix dereference of irq data in shutdown gpio: amd-fch: Fix type error found by sparse gpio: amd-fch: Drop const from resource gpio: mxc: add check to return defer probe if clock tree NOT ready gpio: ftgpio: Register per-instance irqchip gpio: ixp4xx: Add DT bindings x86: pcengines apuv2 gpio/leds/keys platform driver gpio: AMD G-Series PCH gpio driver drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource() gpio: tqmx86: Set proper output level for direction_output gpio: sprd: Change to use SoC compatible string gpio: sprd: Use SoC compatible string instead of wildcard string gpio: of: Handle both enable-gpio{,s} gpio: of: Restrict enable-gpio quirk to regulator-gpio gpio: davinci: use devm_platform_ioremap_resource() ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfdLinus Torvalds authored
Pull MFD updates from Lee Jones: "New Drivers: - Add STMPE ADC Input driver - Add STMicroelectronics STPMIC1 Parent driver - Add STMicroelectronics STPMIC1 OnKey Misc driver - Add STMicroelectronics STPMIC1 Watchdog driver - Add Cirrus Logic Lochnagar Parent driver - Add TQ-Systems TQMX86 Parent driver New Device Support: - Add support for ADC to STMPE New (or moved) Functionality: - Move Lightbar functionality to its own driver; cros_ec_lightbar - Move VBC functionality to its own driver; cros_ec_vbc - Move VBC functionality to its own driver; cros_ec_vbc - Move DebugFS functionality to its own driver; cros_ec_debugfs - Move SYSFS functionality to its own driver; cros_ec_sysfs - Add support for input voltage options; tps65218 Fixes: - Use devm_* managed resources; cros_ec - Device Tree documentation; stmpe, aspeed-lpc, lochnagar - Trivial Clean-ups; stmpe - Rip out broken modular code; aat2870-core, adp5520, as3711, db8500-prcmu, htc-i2cpld, max8925-core, rc5t583, sta2x11-mfd, syscon, tps65090, tps65910, tps68470 tps80031, wm831x-spi, wm831x-i2c, wm831x-core, wm8350-i2c, wm8350-core, wm8400-core - Kconfig fixups; INTEL_SOC_PMIC - Improve error path; sm501, sec-core - Use struct_size() helper; sm501 - Constify; at91-usart - Use pointers instead of copying data; at91-usart - Deliver proper return value; cros_ec_dev - Trivial formatting/whitespace; sec-core" * tag 'mfd-next-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits) mfd: mxs-lradc: Mark expected switch fall-through mfd: sec-core: Cleanup formatting to a consistent style mfd: tqmx86: IO controller with I2C, Wachdog and GPIO mfd: intel-lpss: Move linux/pm.h to the local header mfd: cros_ec_dev: Return number of bytes read with CROS_EC_DEV_IOCRDMEM mfd: tps68470: Drop unused MODULE_DEVICE_TABLE mfd: at91-usart: No need to copy mfd_cell in probe mfd: at91-usart: Constify at91_usart_spi_subdev and at91_usart_serial_subdev mfd: lochnagar: Add support for the Cirrus Logic Lochnagar mfd: lochnagar: Add initial binding documentation dt-bindings: mfd: aspeed-lpc: Make parameter optional mfd: sec-core: Return gracefully instead of BUG() if device cannot match mfd: sm501: Use struct_size() in devm_kzalloc() mfd: sm501: Fix potential NULL pointer dereference mfd: Kconfig: Fix I2C_DESIGNWARE_PLATFORM dependencies mfd: tps65218.c: Add input voltage options mfd: wm8400-core: Make it explicitly non-modular mfd: wm8350-core: Drop unused module infrastructure from non-modular code mfd: wm8350-i2c: Make it explicitly non-modular mfd: wm831x-core: Drop unused module infrastructure from non-modular code ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlightLinus Torvalds authored
Pull backlight fixlet from Lee Jones: "Allow GPIO call to sleep in pwm_bl driver" * tag 'backlight-next-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: backlight: pwm_bl: Use gpiod_get_value_cansleep() to get initial state
-
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linuxLinus Torvalds authored
Pull RTC updates from Alexandre Belloni: "There is an unusual amount of new drivers this cycle, and this explains the number of insertions. Other than that, the changes are the usual fixes and feature addition. Subsystem updates: - new quartz-load-femtofarads DT property for quartz load capacitance - remove rtc_class_ops.read_callback New drivers: - Abracon AB-RTCMC-32.768kHz-EOZ9 - Amlogic Meson RTC - Cadence RTC IP - Microcrystal RV3028 - Whwave sd3078 Driver updates: - cmos: ignore bogus century byte - ds1307: rework rx8130 support - isl1208: add isl1209 support, nvmem support - rs5C372: report invalid time when the oscillator stopped - rx8581: add rx8571 support" * tag 'rtc-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (66 commits) rtc: pic32: convert to SPDX identifier rtc: pic32: let the core handle range rtc: pic32: convert to devm_rtc_allocate_device rtc: update my email address rtc: rv8803: convert to SPDX identifier rtc: rv8803: let the core handle range rtc: tx4939: convert to SPDX identifier rtc: tx4939: use .set_time rtc: tx4939: switch to rtc_time64_to_tm/rtc_tm_to_time64 rtc: tx4939: set range rtc: tx4939: remove useless test rtc: zynqmp: let the core handle range rtc: zynqmp: fix possible race condition rtc: imx-sc: use rtc_time64_to_tm rtc: rx8581: Add support for Epson rx8571 RTC dt-bindings: rtc: add rx8571 compatible rtc: pcf85063: remove dead code rtc: remove rtc_class_ops.read_callback rtc: add AB-RTCMC-32.768kHz-EOZ9 RTC support dt-bindings: rtc: add ABEOZ9 ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermalLinus Torvalds authored
Pull thermal soc updates from Eduardo Valentin: "Specifics: - mediatek thermal now supports MT8183 - broadcom thermal now supports Stingray - qoirq now supports multiple sensors - fixes on different drivers: rcar, tsens, tegra Some new drivers are still pending further review and I chose to leave them for the next merge window while still sending this material" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: thermal: rcar_gen3_thermal: Register hwmon sysfs interface thermal/qcom/tsens-common : fix possible object reference leak thermal: tegra: add get_trend ops thermal: tegra: fix memory allocation thermal: tegra: remove unnecessary warnings thermal: mediatek: add support for MT8183 dt-bindings: thermal: add binding document for mt8183 thermal controller thermal: mediatek: add flag for bank selection thermal: mediatek: add thermal controller offset thermal: mediatek: add calibration item thermal: mediatek: add common index of vts settings. thermal: mediatek: fix register index error thermal: qoriq: add multiple sensors support thermal: broadcom: Add Stingray thermal driver dt-bindings: thermal: Add binding document for SR thermal
-
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibftLinus Torvalds authored
Pull ibft updates from Konrad Rzeszutek Wilk: "Two tiny fixes - a missing break, and upgrading the subsystem to use modern macros" * 'stable/for-linus-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft: iscsi_ibft: use virt_to_phys instead of isa_virt_to_bus iscsi_ibft: Fix missing break in switch statement
-
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlbLinus Torvalds authored
Pull swiotlb updates from Konrad Rzeszutek Wilk: "Expands the SWIOTLB to have debugfs support (along with bug-fixes), and a tiny fix" * 'stable/for-linus-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb: swiotlb: drop pointless static qualifier in swiotlb_create_debugfs() swiotlb: checking whether swiotlb buffer is full with io_tlb_used swiotlb: add debugfs to track swiotlb buffer usage swiotlb: fix comment on swiotlb_bounce()
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c updates from Wolfram Sang: - the I2C core gained helpers to assist drivers in handling their suspended state, and drivers were converted to use it - two new fault-injectors for stress-testing - bigger refactoring and feature improvements for the ocores, sh_mobile, and tegra drivers - platform_data removal for the at24 EEPROM driver - ... and various improvements and bugfixes all over the subsystem * 'i2c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (69 commits) i2c: Allow recovery of the initial IRQ by an I2C client device. i2c: ocores: turn incomplete kdoc into a comment i2c: designware: Do not allow i2c_dw_xfer() calls while suspended i2c: tegra: Only display error messages if DMA setup fails i2c: gpio: fault-injector: add 'inject_panic' injector i2c: gpio: fault-injector: add 'lose_arbitration' injector i2c: tegra: remove multi-master support i2c: tegra: remove master fifo support on tegra186 i2c: tegra: change phrasing, "fallbacking" to "falling back" i2c: expand minor range when registering chrdev region i2c: aspeed: Add multi-master use case support i2c: core-smbus: don't trace smbus_reply data on errors i2c: ocores: Add support for bus clock via platform data i2c: ocores: Add support for IO mapper registers. i2c: ocores: checkpatch fixes i2c: ocores: add SPDX tag i2c: ocores: add polling interface i2c: ocores: do not handle IRQ if IF is not set i2c: ocores: stop transfer on timeout i2c: tegra: add i2c interface timing support ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supplyLinus Torvalds authored
Pull power supply and reset updates from Sebastian Reichel: "Nothing too fancy in the power-supply subsystem this time. There are less patches than usual, since I did not have enough time to review them in time. The good news is, that all patches have been in linux-next for more than two weeks and there are no complicated cross-subsystem patchsets this time! Summary: - at91-reset: add sam9x60 support - sc27xx: improve capacity logic - goldfish_battery: enhance driver by adding many new properties - isp1704: drop platform data and migrate to gpiod - misc small fixes and improvements" * tag 'for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (25 commits) power: reset: at91-reset: add support for sam9x60 SoC dt-bindings: arm: atmel: add new sam9x60 reset controller binding dt-bindings: arm: atmel: add missing samx7 to reset controller max17042_battery: fix potential use-after-free on device remove power: supply: core: Add a field to support battery max voltage dt-bindings: power: supply: Add voltage-max-design-microvolt property bq27x00: use cached flags power: supply: ds2782: fix possible use-after-free on remove power: supply: bq25890: show max charge current/voltage as configured power: supply: sc27xx: Fix capacity saving function power: supply: sc27xx: Fix the incorrect formula when converting capacity to coulomb counter power: supply: sc27xx: Add one property to read charge voltage dt-bindings: power: sc27xx: Add one IIO channel to read charge voltage drivers: power: supply: goldfish_battery: Add support for reading more properties power: supply: charger-manager: Fix trivial language typos cpcap-charger: generate events for userspace power: supply: remove some duplicated includes power: twl4030: fix a missing check of return value drivers: power: supply: goldfish_battery: Use tabs for alignment drivers: power: supply: goldfish_battery: Fix alignment ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsiLinus Torvalds authored
Pull HIS update from Sebastian Reichel: "Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE" * tag 'hsi-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi: HSI: omap_ssi_port: fix debugfs_simple_attr.cocci warnings
-
git://github.com/cminyard/linux-ipmiLinus Torvalds authored
Pull IPMI updates from Corey Minyard: "A couple of bug fixes and a bunch of code cleanup: - Fix a use after free error in a certain error situation. - Fix some flag handling issues in the SSIF (I2C) IPMI driver. - A bunch of cleanups, spacing issues, converting pr_xxx to dev_xxx, use standard UUID handling, and some other minor stuff. - The IPMI code was creating a platform device if none was supplied. Instead of doing that, have every source that creates an IPMI device supply a device struct. This fixes several issues,including a crash in one situation, and cleans things up a bit" * tag 'for-linus-5.1' of git://github.com/cminyard/linux-ipmi: ipmi_si: Potential array underflow in hotmod_handler() ipmi_si: Remove hacks for adding a dummy platform devices ipmi_si: Consolidate scanning the platform bus ipmi_si: Remove hotmod devices on removal and exit ipmi_si: Remove hardcode IPMI devices by scanning the platform bus ipmi_si: Switch hotmod to use a platform device ipmi: Consolidate the adding of platform devices ipmi_si: Rename addr_type to addr_space to match what it does ipmi_si: Convert some types into unsigned ipmi_si: Fix crash when using hard-coded device ipmi: Use dedicated API for copying a UUID ipmi: Use defined constant for UUID representation ipmi:ssif: Change some pr_xxx to dev_xxx calls ipmi: kcs_bmc: handle devm_kasprintf() failure case ipmi: Fix return value when a message is truncated ipmi: clean an indentation issue, remove extraneous space ipmi: Make the smi watcher be disabled immediately when not needed ipmi: Fix how the lower layers are told to watch for messages ipmi: Fix SSIF flag requests ipmi_si: fix use-after-free of resource->name
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull RAS updates from Borislav Petkov: "This time around we have in store: - Disable MC4_MISC thresholding banks on all AMD family 0x15 models (Shirish S) - AMD MCE error descriptions update and error decode improvements (Yazen Ghannam) - The usual smaller conversions and fixes" * 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/mce: Improve error message when kernel cannot recover, p2 EDAC/mce_amd: Decode MCA_STATUS in bit definition order EDAC/mce_amd: Decode MCA_STATUS[Scrub] bit EDAC, mce_amd: Print ExtErrorCode and description on a single line EDAC, mce_amd: Match error descriptions to latest documentation x86/MCE/AMD, EDAC/mce_amd: Add new error descriptions for some SMCA bank types x86/MCE/AMD, EDAC/mce_amd: Add new McaTypes for CS, PSP, and SMU units x86/MCE/AMD, EDAC/mce_amd: Add new MP5, NBIO, and PCIE SMCA bank types RAS: Add a MAINTAINERS entry RAS: Use consistent types for UUIDs x86/MCE/AMD: Carve out the MC4_MISC thresholding quirk x86/MCE/AMD: Turn off MC4_MISC thresholding on all family 0x15 models x86/MCE: Switch to use the new generic UUID API
-
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bpLinus Torvalds authored
Pull EDAC updates from Borislav Petkov: - A new EDAC AST 2500 SoC driver (Stefan M Schaeckeler) - New i10nm EDAC driver for Intel 10nm CPUs (Qiuxu Zhuo and Tony Luck) - Altera SDRAM functionality carveout for separate enablement of RAS and SDRAM capabilities on some Altera chips. (Thor Thayer) - The usual round of cleanups and fixes And last but not least: recruit James Morse as a reviewer for the ARM side. * tag 'edac_for_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: EDAC/altera: Add separate SDRAM EDAC config EDAC, altera: Add missing of_node_put() EDAC, skx_common: Add code to recognise new compound error code EDAC, i10nm: Fix randconfig builds EDAC, i10nm: Add a driver for Intel 10nm server processors EDAC, skx_edac: Delete duplicated code EDAC, skx_common: Separate common code out from skx_edac EDAC: Do not check return value of debugfs_create() functions EDAC: Add James Morse as a reviewer dt-bindings, EDAC: Add Aspeed AST2500 EDAC, aspeed: Add an Aspeed AST2500 EDAC driver
-
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hidLinus Torvalds authored
Pull HID updates from Jiri Kosina: - support for Pro Pen slim, from Jason Gerecke - power management improvements to Intel-ISH driver, from Song Hongyan - UCLogic driver revamp in order to be able to support wider range of Huion tablets, from Nikolai Kondrashov - Asus Transbook support, from NOGUCHI Hiroshi - other assorted small bugfixes / cleanups and device ID additions * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (46 commits) HID: Remove Waltop tablets from hid_have_special_driver HID: Remove KYE tablets from hid_have_special_driver HID: Remove hid-uclogic entries from hid_have_special_driver HID: uclogic: Do not initialize non-USB devices HID: uclogic: Add support for Ugee G5 HID: uclogic: Support Gray-coded rotary encoders HID: uclogic: Support faking Wacom pad device ID HID: uclogic: Add support for XP-Pen Deco 01 HID: uclogic: Add support for XP-Pen Star G640 HID: uclogic: Add support for XP-Pen Star G540 HID: uclogic: Add support for Ugee EX07S frame controls HID: uclogic: Add support for Ugee M540 HID: uclogic: Add support for Ugee 2150 HID: uclogic: Support v2 protocol HID: uclogic: Support fragmented high-res reports HID: uclogic: Support in-range reporting emulation HID: uclogic: Designate current protocol v1 HID: uclogic: Re-initialize tablets on resume HID: uclogic: Extract tablet parameter discovery into a module HID: uclogic: Extract report descriptors to a module ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatchingLinus Torvalds authored
Pull livepatching updates from Jiri Kosina: - support for something we call 'atomic replace', and allows for much better handling of cumulative patches (which is something very useful for distros), from Jason Baron with help of Petr Mladek and Joe Lawrence - improvement of handling of tasks blocking finalization, from Miroslav Benes - update of MAINTAINERS file to reflect move towards group maintainership * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching: (22 commits) livepatch/selftests: use "$@" to preserve argument list livepatch: Module coming and going callbacks can proceed with all listed patches livepatch: Proper error handling in the shadow variables selftest livepatch: return -ENOMEM on ptr_id() allocation failure livepatch: Introduce klp_for_each_patch macro livepatch: core: Return EOPNOTSUPP instead of ENOSYS selftests/livepatch: add DYNAMIC_DEBUG config dependency livepatch: samples: non static warnings fix livepatch: update MAINTAINERS livepatch: Remove signal sysfs attribute livepatch: Send a fake signal periodically selftests/livepatch: introduce tests livepatch: Remove ordering (stacking) of the livepatches livepatch: Atomic replace and cumulative patches documentation livepatch: Remove Nop structures when unused livepatch: Add atomic replace livepatch: Use lists to manage patches, objects and functions livepatch: Simplify API by removing registration step livepatch: Don't block the removal of patches loaded after a forced transition livepatch: Consolidate klp_free functions ...
-
git://anongit.freedesktop.org/drm/drmLinus Torvalds authored
Pull drm updates from Dave Airlie: "This is the main drm pull request for the 5.1 merge window. The big changes I'd highlight are: - nouveau has HMM support now, there is finally an in-tree user so we can quieten down the rip it out people. - i915 now enables fastboot by default on Skylake+ - Displayport Multistream support has been refactored and should hopefully be more reliable. Core: - header cleanups aiming towards removing drmP.h - dma-buf fence seqnos to 64-bits - common helper for DP mst hotplug for radeon,i915,amdgpu + new refcounting scheme - MST i2c improvements - drm_syncobj_cb removal - ARM FB compression fourcc - P010 + P016 fourcc - allwinner tiled format modifier - i2c over aux I2C_M_STOP support - DRM_AUTH handling fixes TTM: - ref/unref renaming New driver: - ARM komeda display driver scheduler: - refactor mirror list handling - rework hw fence processing - 0 run queue entity fix bridge: - TI DS90C185 LVDS bridge - thc631lvdm83d bridge improvements - cadence + allwinner DSI ported to generic phy panels: - Sitronix ST7701 panel - Kingdisplay KD097D04 - LeMaker BL035-RGB-002 - PDA 91-00156-A0 - Innolux EE101IA-01D i915: - Enable fastboot by default on SKL+/VLV/CHV - Export RPCS configuration for ICL media driver - Coffelake PCI ID - CNL clocks setup fixes - ACPI/PMIC support for MIPI/DSI - Per-engine WA init for all engines - Shrinker locking fixes - Kerneldoc updates - Lots of ring improvements and reset fixes - Coffeelake GVT Support - VFIO GVT EDID Region support - runtime PM wakeref tracking - ILK->IVB primary plane enable delays - userptr mutex locking fixes - DSI fixes - LVDS/TV cleanups - HW readout fixes - LUT robustness fixes - ICL display and watermark fixes - gem mmap race fix amdgpu: - add scheduled dependencies interface - DCC on scanout surfaces - vega10/20 BACO support - Multiple IH rings on soc15 - XGMI locking fixes - DC i2c/aux cleanups - runtime SMU debug interface - Kexec improvmeents - SR-IOV fixes - DC freesync + ABM fixes - GDS fixes - GPUVM fixes - vega20 PCIE DPM switching fixes - Context priority handling fixes radeon: - fix missing break in evergreen parser nouveau: - SVM support via HMM msm: - QCOM Compressed modifier support exynos: - s5pv210 rotator support imx: - zpos property support - pending update fixes v3d: - cache flush improvments vc4: - reflection support - HDMI overscan support tegra: - CEC refactoring - HDMI audio fixes - Tegra186 prep work - SOR crossbar device tree fixes sun4i: - implicit fencing support - YUV and scalar support improvements - A23 support - tiling fixes atmel-hlcdc: - clipping and rotation property fixes qxl: - BO and PRIME improvements - generic fbdev emulation dw-hdmi: - HDMI 2.0 2160p - YUV420 ouput rockchip: - implicit fencing support - reflection proerties virtio-gpu: - use generic fbdev emulation tilcdc: - cpufreq vs crtc init fix rcar-du: - R8A774C0 support - D3/E3 RGB output routing fixes and DPAD0 support - RA87744 LVDS support bochs: - atomic and generic fbdev emulation - ID mismatch error on bochs load meson: - remove firmware fbs" * tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm: (1130 commits) drm/amd/display: Use vrr friendly pageflip throttling in DC. drm/imx: only send commit done event when all state has been applied drm/imx: allow building under COMPILE_TEST drm/imx: imx-tve: depend on COMMON_CLK drm/imx: ipuv3-plane: add zpos property drm/imx: ipuv3-plane: add function to query atomic update status gpu: ipu-v3: prg: add function to get channel configure status gpu: ipu-v3: pre: add double buffer status readback drm/amdgpu: Bump amdgpu version for context priority override. drm/amdgpu/powerplay: fix typo in BACO header guards drm/amdgpu/powerplay: fix return codes in BACO code drm/amdgpu: add missing license on baco files drm/bochs: Fix the ID mismatch error drm/nouveau/dmem: use dma addresses during migration copies drm/nouveau/dmem: use physical vram addresses during migration copies drm/nouveau/dmem: extend copy function to allow direct use of physical addresses drm/nouveau/svm: new ioctl to migrate process memory to GPU memory drm/nouveau/dmem: device memory helpers for SVM drm/nouveau/svm: initial support for shared virtual memory drm/nouveau: prepare for enabling svm with existing userspace interfaces ...
-
Russell King authored
Tony notes that the GPIO module does not idle when level interrupts are in use, as the wakeup appears to get stuck. After extensive investigation, it appears that the wakeup will only be cleared if the interrupt status register is cleared while the interrupt is enabled. However, we are currently clearing it with the interrupt disabled for level-based interrupts. It is acknowledged that this observed behaviour conflicts with a statement in the TRM: CAUTION After servicing the interrupt, the status bit in the interrupt status register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be reset and the interrupt line released (by setting the corresponding bit of the interrupt status register to 1) before enabling an interrupt for the GPIO channel in the interrupt-enable register (GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent the occurrence of unexpected interrupts when enabling an interrupt for the GPIO channel. However, this does not appear to be a practical problem. Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>, the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP: Fix the sequence to clear the IRQ status" saying: if the status is cleared after disabling the IRQ then sWAKEUP will not be cleared and gates the module transition When we unmask the level interrupt after the interrupt has been handled, enable the interrupt and only then clear the interrupt. If the interrupt is still pending, the hardware will re-assert the interrupt status. Should the caution note in the TRM prove to be a problem, we could use a clear-enable-clear sequence instead. Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Keerthy <j-keerthy@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> [tony@atomide.com: updated comments based on an earlier TI patch] Signed-off-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Axel Lin authored
Current amd_fch_gpio_direction_output implementation ignores the value argument, fix it so direction_output will set proper output level. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by:
Enrico Weigelt <info@metux.net> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Arnd Bergmann authored
The driver was newly introduced but the version that got merged produces a harmless compiler warning: drivers/platform/x86/pcengines-apuv2.c: In function 'apu_board_init': drivers/platform/x86/pcengines-apuv2.c:211:6: error: unused variable 'rc' [-Werror=unused-variable] Remove the evidently useless variable. Fixes: f8eb0235 ("x86: pcengines apuv2 gpio/leds/keys platform driver") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-By:
Enrico Weigelt, metux IT consult <info@metux.net> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Andy Shevchenko authored
The commit 0cdf21b3 ("gpio: pca953x: set the PCA_PCAL flag also when matching by DT") introduces a helper macro which tells that chip supports latched interrupts, but the macro was never used for ACPI or legacy enumeration. So, make use of it for legacy and ACPI enumeration. Cc: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Randy Dunlap authored
Fix Kconfig warning for PCENGINES_APU2 symbol: WARNING: unmet direct dependencies detected for KEYBOARD_GPIO_POLLED Depends on [n]: !UML && INPUT [=y] && INPUT_KEYBOARD [=n] && GPIOLIB [=y] Selected by [y]: - PCENGINES_APU2 [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] Add INPUT_KEYBOARD dependency for KEYBOARD_GPIO_POLLED. Add LEDS_CLASS dependency for LEDS_GPIO. Fixes: f8eb0235 ("x86: pcengines apuv2 gpio/leds/keys platform driver") Reported-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Enrico Weigelt, metux IT consult <info@metux.net> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org>
-
Linus Torvalds authored
Merge more updates from Andrew Morton: - some of the rest of MM - various misc things - dynamic-debug updates - checkpatch - some epoll speedups - autofs - rapidio - lib/, lib/lzo/ updates * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (83 commits) samples/mic/mpssd/mpssd.h: remove duplicate header kernel/fork.c: remove duplicated include include/linux/relay.h: fix percpu annotation in struct rchan arch/nios2/mm/fault.c: remove duplicate include unicore32: stop printing the virtual memory layout MAINTAINERS: fix GTA02 entry and mark as orphan mm: create the new vm_fault_t type arm, s390, unicore32: remove oneliner wrappers for memblock_alloc() arch: simplify several early memory allocations openrisc: simplify pte_alloc_one_kernel() sh: prefer memblock APIs returning virtual address microblaze: prefer memblock API returning virtual address powerpc: prefer memblock APIs returning virtual address lib/lzo: separate lzo-rle from lzo lib/lzo: implement run-length encoding lib/lzo: fast 8-byte copy on arm64 lib/lzo: 64-bit CTZ on arm64 lib/lzo: tidy-up ifdefs ipc/sem.c: replace kvmalloc/memset with kvzalloc and use struct_size ipc: annotate implicit fall through ...
-
Brajeswar Ghosh authored
Remove duplicate headers which are included more than once Link: http://lkml.kernel.org/r/20190114170033.GA3674@hp-pavilion-15-notebook-pc-brajeswarSigned-off-by:
Brajeswar Ghosh <brajeswar.linux@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
YueHaibing authored
Remove duplicated include. Link: http://lkml.kernel.org/r/20181209062952.17736-1-yuehaibing@huawei.comSigned-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Luc Van Oostenryck authored
The percpu member of this structure is declared as: struct ... ** __percpu member; So its type is: __percpu pointer to pointer to struct ... But looking at how it's used, its type should be: pointer to __percpu pointer to struct ... and it should thus be declared as: struct ... * __percpu *member; So fix the placement of '__percpu' in the definition of this structures. This silents a few Sparse's warnings like: warning: incorrect type in initializer (different address spaces) expected void const [noderef] <asn:3> *__vpp_verify got struct sched_domain ** Link: http://lkml.kernel.org/r/20190118144902.79065-1-luc.vanoostenryck@gmail.com Fixes: 017c59c0 ("relay: Use per CPU constructs for the relay channel buffer pointers") Signed-off-by:
Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Cc: Jens Axboe <axboe@suse.de> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Sabyasachi Gupta authored
Remove linux/ptrace.h which is included more than once Link: http://lkml.kernel.org/r/5c45d345.1c69fb81.d90ed.8e05@mx.google.comSigned-off-by:
Sabyasachi Gupta <sabyasachi.linux@gmail.com> Cc: Ley Foon Tan <lftan@altera.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Geert Uytterhoeven authored
Since commit ad67b74d ("printk: hash addresses printed with %p"), the virtual memory layout printed during boot up contains "ptrval" instead of actual addresses. Instead of changing the printing to "%px", and leaking virtual memory layout information again, just remove the printing completely, cfr. e.g. commits 071929db ("arm64: Stop printing the virtual memory layout") and 31833332 ("m68k/mm: Stop printing the virtual memory layout"). All interesting information (actual section sizes) is already printed by mem_init_print_info() just above anyway. Link: http://lkml.kernel.org/r/20190121152254.29079-1-geert+renesas@glider.beSigned-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Kees Cook <keescook@chromium.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-