Merge branch 'topic/xilinx' into for-linus

Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt

+Xilinx AXI VDMA engine, it does transfers between memory and video devices.
+It can be configured to have one channel or two channels. If configured
+as two channels, one is to transmit to the video device and another is
+to receive from the video device.
+
+Required properties:
+- compatible: Should be "xlnx,axi-vdma-1.00.a"
+- #dma-cells: Should be <1>, see "dmas" property below
+- reg: Should contain VDMA registers location and length.
+- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w.
+- dma-channel child node: Should have at least one channel and can have up to
+	two channels per device. This node specifies the properties of each
+	DMA channel (see child node properties below).
+
+Optional properties:
+- xlnx,include-sg: Tells configured for Scatter-mode in
+	the hardware.
+- xlnx,flush-fsync: Tells which channel to Flush on Frame sync.
+	It takes following values:
+	{1}, flush both channels
+	{2}, flush mm2s channel
+	{3}, flush s2mm channel
+
+Required child node properties:
+- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or
+	"xlnx,axi-vdma-s2mm-channel".
+- interrupts: Should contain per channel VDMA interrupts.
+- xlnx,data-width: Should contain the stream data width, take values
+	{32,64...1024}.
+
+Optional child node properties:
+- xlnx,include-dre: Tells hardware is configured for Data
+	Realignment Engine.
+- xlnx,genlock-mode: Tells Genlock synchronization is
+	enabled/disabled in hardware.
+
+Example:
+++++++++
+
+axi_vdma_0: axivdma@40030000 {
+	compatible = "xlnx,axi-vdma-1.00.a";
+	#dma_cells = <1>;
+	reg = < 0x40030000 0x10000 >;
+	xlnx,num-fstores = <0x8>;
+	xlnx,flush-fsync = <0x1>;
+	dma-channel@40030000 {
+		compatible = "xlnx,axi-vdma-mm2s-channel";
+		interrupts = < 0 54 4 >;
+		xlnx,datawidth = <0x40>;
+	} ;
+	dma-channel@40030030 {
+		compatible = "xlnx,axi-vdma-s2mm-channel";
+		interrupts = < 0 53 4 >;
+		xlnx,datawidth = <0x40>;
+	} ;
+} ;
+
+
+* DMA client
+
+Required properties:
+- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,
+	where Channel ID is '0' for write/tx and '1' for read/rx
+	channel.
+- dma-names: a list of DMA channel names, one per "dmas" entry
+
+Example:
+++++++++
+
+vdmatest_0: vdmatest@0 {
+	compatible ="xlnx,axi-vdma-test-1.00.a";
+	dmas = <&axi_vdma_0 0
+		&axi_vdma_0 1>;
+	dma-names = "vdma0", "vdma1";
+} ;

drivers/dma/Kconfig

@@ -361,6 +361,20 @@ config FSL_EDMA
 	  multiplexing capability for DMA request sources(slot).
 	  This module can be found on Freescale Vybrid and LS-1 SoCs.
 
+config XILINX_VDMA
+	tristate "Xilinx AXI VDMA Engine"
+	depends on (ARCH_ZYNQ || MICROBLAZE)
+	select DMA_ENGINE
+	help
+	  Enable support for Xilinx AXI VDMA Soft IP.
+
+	  This engine provides high-bandwidth direct memory access
+	  between memory and AXI4-Stream video type target
+	  peripherals including peripherals which support AXI4-
+	  Stream Video Protocol.  It has two stream interfaces/
+	  channels, Memory Mapped to Stream (MM2S) and Stream to
+	  Memory Mapped (S2MM) for the data transfers.
+
 config DMA_ENGINE
 	bool
 

drivers/dma/Makefile

@@ -46,3 +46,4 @@ obj-$(CONFIG_K3_DMA) += k3dma.o
 obj-$(CONFIG_MOXART_DMA) += moxart-dma.o
 obj-$(CONFIG_FSL_EDMA) += fsl-edma.o
 obj-$(CONFIG_QCOM_BAM_DMA) += qcom_bam_dma.o
+obj-y += xilinx/

drivers/dma/xilinx/Makefile

+obj-$(CONFIG_XILINX_VDMA) += xilinx_vdma.o

drivers/dma/xilinx/xilinx_vdma.c

+/*
+ * DMA driver for Xilinx Video DMA Engine
+ *
+ * Copyright (C) 2010-2014 Xilinx, Inc. All rights reserved.
+ *
+ * Based on the Freescale DMA driver.
+ *
+ * Description:
+ * The AXI Video Direct Memory Access (AXI VDMA) core is a soft Xilinx IP
+ * core that provides high-bandwidth direct memory access between memory
+ * and AXI4-Stream type video target peripherals. The core provides efficient
+ * two dimensional DMA operations with independent asynchronous read (S2MM)
+ * and write (MM2S) channel operation. It can be configured to have either
+ * one channel or two channels. If configured as two channels, one is to
+ * transmit to the video device (MM2S) and another is to receive from the
+ * video device (S2MM). Initialization, status, interrupt and management
+ * registers are accessed through an AXI4-Lite slave interface.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/amba/xilinx_dma.h>
+#include <linux/bitops.h>
+#include <linux/dmapool.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_dma.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/slab.h>
+
+#include "../dmaengine.h"
+
+/* Register/Descriptor Offsets */
+#define XILINX_VDMA_MM2S_CTRL_OFFSET		0x0000
+#define XILINX_VDMA_S2MM_CTRL_OFFSET		0x0030
+#define XILINX_VDMA_MM2S_DESC_OFFSET		0x0050
+#define XILINX_VDMA_S2MM_DESC_OFFSET		0x00a0
+
+/* Control Registers */
+#define XILINX_VDMA_REG_DMACR			0x0000
+#define XILINX_VDMA_DMACR_DELAY_MAX		0xff
+#define XILINX_VDMA_DMACR_DELAY_SHIFT		24
+#define XILINX_VDMA_DMACR_FRAME_COUNT_MAX	0xff
+#define XILINX_VDMA_DMACR_FRAME_COUNT_SHIFT	16
+#define XILINX_VDMA_DMACR_ERR_IRQ		BIT(14)
+#define XILINX_VDMA_DMACR_DLY_CNT_IRQ		BIT(13)
+#define XILINX_VDMA_DMACR_FRM_CNT_IRQ		BIT(12)
+#define XILINX_VDMA_DMACR_MASTER_SHIFT		8
+#define XILINX_VDMA_DMACR_FSYNCSRC_SHIFT	5
+#define XILINX_VDMA_DMACR_FRAMECNT_EN		BIT(4)
+#define XILINX_VDMA_DMACR_GENLOCK_EN		BIT(3)
+#define XILINX_VDMA_DMACR_RESET			BIT(2)
+#define XILINX_VDMA_DMACR_CIRC_EN		BIT(1)
+#define XILINX_VDMA_DMACR_RUNSTOP		BIT(0)
+#define XILINX_VDMA_DMACR_FSYNCSRC_MASK		GENMASK(6, 5)
+
+#define XILINX_VDMA_REG_DMASR			0x0004
+#define XILINX_VDMA_DMASR_EOL_LATE_ERR		BIT(15)
+#define XILINX_VDMA_DMASR_ERR_IRQ		BIT(14)
+#define XILINX_VDMA_DMASR_DLY_CNT_IRQ		BIT(13)
+#define XILINX_VDMA_DMASR_FRM_CNT_IRQ		BIT(12)
+#define XILINX_VDMA_DMASR_SOF_LATE_ERR		BIT(11)
+#define XILINX_VDMA_DMASR_SG_DEC_ERR		BIT(10)
+#define XILINX_VDMA_DMASR_SG_SLV_ERR		BIT(9)
+#define XILINX_VDMA_DMASR_EOF_EARLY_ERR		BIT(8)
+#define XILINX_VDMA_DMASR_SOF_EARLY_ERR		BIT(7)
+#define XILINX_VDMA_DMASR_DMA_DEC_ERR		BIT(6)
+#define XILINX_VDMA_DMASR_DMA_SLAVE_ERR		BIT(5)
+#define XILINX_VDMA_DMASR_DMA_INT_ERR		BIT(4)
+#define XILINX_VDMA_DMASR_IDLE			BIT(1)
+#define XILINX_VDMA_DMASR_HALTED		BIT(0)
+#define XILINX_VDMA_DMASR_DELAY_MASK		GENMASK(31, 24)
+#define XILINX_VDMA_DMASR_FRAME_COUNT_MASK	GENMASK(23, 16)
+
+#define XILINX_VDMA_REG_CURDESC			0x0008
+#define XILINX_VDMA_REG_TAILDESC		0x0010
+#define XILINX_VDMA_REG_REG_INDEX		0x0014
+#define XILINX_VDMA_REG_FRMSTORE		0x0018
+#define XILINX_VDMA_REG_THRESHOLD		0x001c
+#define XILINX_VDMA_REG_FRMPTR_STS		0x0024
+#define XILINX_VDMA_REG_PARK_PTR		0x0028
+#define XILINX_VDMA_PARK_PTR_WR_REF_SHIFT	8
+#define XILINX_VDMA_PARK_PTR_RD_REF_SHIFT	0
+#define XILINX_VDMA_REG_VDMA_VERSION		0x002c
+
+/* Register Direct Mode Registers */
+#define XILINX_VDMA_REG_VSIZE			0x0000
+#define XILINX_VDMA_REG_HSIZE			0x0004
+
+#define XILINX_VDMA_REG_FRMDLY_STRIDE		0x0008
+#define XILINX_VDMA_FRMDLY_STRIDE_FRMDLY_SHIFT	24
+#define XILINX_VDMA_FRMDLY_STRIDE_STRIDE_SHIFT	0
+
+#define XILINX_VDMA_REG_START_ADDRESS(n)	(0x000c + 4 * (n))
+
+/* HW specific definitions */
+#define XILINX_VDMA_MAX_CHANS_PER_DEVICE	0x2
+
+#define XILINX_VDMA_DMAXR_ALL_IRQ_MASK	\
+		(XILINX_VDMA_DMASR_FRM_CNT_IRQ | \
+		 XILINX_VDMA_DMASR_DLY_CNT_IRQ | \
+		 XILINX_VDMA_DMASR_ERR_IRQ)
+
+#define XILINX_VDMA_DMASR_ALL_ERR_MASK	\
+		(XILINX_VDMA_DMASR_EOL_LATE_ERR | \
+		 XILINX_VDMA_DMASR_SOF_LATE_ERR | \
+		 XILINX_VDMA_DMASR_SG_DEC_ERR | \
+		 XILINX_VDMA_DMASR_SG_SLV_ERR | \
+		 XILINX_VDMA_DMASR_EOF_EARLY_ERR | \
+		 XILINX_VDMA_DMASR_SOF_EARLY_ERR | \
+		 XILINX_VDMA_DMASR_DMA_DEC_ERR | \
+		 XILINX_VDMA_DMASR_DMA_SLAVE_ERR | \
+		 XILINX_VDMA_DMASR_DMA_INT_ERR)
+
+/*
+ * Recoverable errors are DMA Internal error, SOF Early, EOF Early
+ * and SOF Late. They are only recoverable when C_FLUSH_ON_FSYNC
+ * is enabled in the h/w system.
+ */
+#define XILINX_VDMA_DMASR_ERR_RECOVER_MASK	\
+		(XILINX_VDMA_DMASR_SOF_LATE_ERR | \
+		 XILINX_VDMA_DMASR_EOF_EARLY_ERR | \
+		 XILINX_VDMA_DMASR_SOF_EARLY_ERR | \
+		 XILINX_VDMA_DMASR_DMA_INT_ERR)
+
+/* Axi VDMA Flush on Fsync bits */
+#define XILINX_VDMA_FLUSH_S2MM		3
+#define XILINX_VDMA_FLUSH_MM2S		2
+#define XILINX_VDMA_FLUSH_BOTH		1
+
+/* Delay loop counter to prevent hardware failure */
+#define XILINX_VDMA_LOOP_COUNT		1000000
+
+/**
+ * struct xilinx_vdma_desc_hw - Hardware Descriptor
+ * @next_desc: Next Descriptor Pointer @0x00
+ * @pad1: Reserved @0x04
+ * @buf_addr: Buffer address @0x08
+ * @pad2: Reserved @0x0C
+ * @vsize: Vertical Size @0x10
+ * @hsize: Horizontal Size @0x14
+ * @stride: Number of bytes between the first
+ *	    pixels of each horizontal line @0x18
+ */
+struct xilinx_vdma_desc_hw {
+	u32 next_desc;
+	u32 pad1;
+	u32 buf_addr;
+	u32 pad2;
+	u32 vsize;
+	u32 hsize;
+	u32 stride;
+} __aligned(64);
+
+/**
+ * struct xilinx_vdma_tx_segment - Descriptor segment
+ * @hw: Hardware descriptor
+ * @node: Node in the descriptor segments list
+ * @phys: Physical address of segment
+ */
+struct xilinx_vdma_tx_segment {
+	struct xilinx_vdma_desc_hw hw;
+	struct list_head node;
+	dma_addr_t phys;
+} __aligned(64);
+
+/**
+ * struct xilinx_vdma_tx_descriptor - Per Transaction structure
+ * @async_tx: Async transaction descriptor
+ * @segments: TX segments list
+ * @node: Node in the channel descriptors list
+ */
+struct xilinx_vdma_tx_descriptor {
+	struct dma_async_tx_descriptor async_tx;
+	struct list_head segments;
+	struct list_head node;
+};
+
+/**
+ * struct xilinx_vdma_chan - Driver specific VDMA channel structure
+ * @xdev: Driver specific device structure
+ * @ctrl_offset: Control registers offset
+ * @desc_offset: TX descriptor registers offset
+ * @lock: Descriptor operation lock
+ * @pending_list: Descriptors waiting
+ * @active_desc: Active descriptor
+ * @allocated_desc: Allocated descriptor
+ * @done_list: Complete descriptors
+ * @common: DMA common channel
+ * @desc_pool: Descriptors pool
+ * @dev: The dma device
+ * @irq: Channel IRQ
+ * @id: Channel ID
+ * @direction: Transfer direction
+ * @num_frms: Number of frames
+ * @has_sg: Support scatter transfers
+ * @genlock: Support genlock mode
+ * @err: Channel has errors
+ * @tasklet: Cleanup work after irq
+ * @config: Device configuration info
+ * @flush_on_fsync: Flush on Frame sync
+ */
+struct xilinx_vdma_chan {
+	struct xilinx_vdma_device *xdev;
+	u32 ctrl_offset;
+	u32 desc_offset;
+	spinlock_t lock;
+	struct list_head pending_list;
+	struct xilinx_vdma_tx_descriptor *active_desc;
+	struct xilinx_vdma_tx_descriptor *allocated_desc;
+	struct list_head done_list;
+	struct dma_chan common;
+	struct dma_pool *desc_pool;
+	struct device *dev;
+	int irq;
+	int id;
+	enum dma_transfer_direction direction;
+	int num_frms;
+	bool has_sg;
+	bool genlock;
+	bool err;
+	struct tasklet_struct tasklet;
+	struct xilinx_vdma_config config;
+	bool flush_on_fsync;
+};
+
+/**
+ * struct xilinx_vdma_device - VDMA device structure
+ * @regs: I/O mapped base address
+ * @dev: Device Structure
+ * @common: DMA device structure
+ * @chan: Driver specific VDMA channel
+ * @has_sg: Specifies whether Scatter-Gather is present or not
+ * @flush_on_fsync: Flush on frame sync
+ */
+struct xilinx_vdma_device {
+	void __iomem *regs;
+	struct device *dev;
+	struct dma_device common;
+	struct xilinx_vdma_chan *chan[XILINX_VDMA_MAX_CHANS_PER_DEVICE];
+	bool has_sg;
+	u32 flush_on_fsync;
+};
+
+/* Macros */
+#define to_xilinx_chan(chan) \
+	container_of(chan, struct xilinx_vdma_chan, common)
+#define to_vdma_tx_descriptor(tx) \
+	container_of(tx, struct xilinx_vdma_tx_descriptor, async_tx)
+
+/* IO accessors */
+static inline u32 vdma_read(struct xilinx_vdma_chan *chan, u32 reg)
+{
+	return ioread32(chan->xdev->regs + reg);
+}
+
+static inline void vdma_write(struct xilinx_vdma_chan *chan, u32 reg, u32 value)
+{
+	iowrite32(value, chan->xdev->regs + reg);
+}
+
+static inline void vdma_desc_write(struct xilinx_vdma_chan *chan, u32 reg,
+				   u32 value)
+{
+	vdma_write(chan, chan->desc_offset + reg, value);
+}
+
+static inline u32 vdma_ctrl_read(struct xilinx_vdma_chan *chan, u32 reg)
+{
+	return vdma_read(chan, chan->ctrl_offset + reg);
+}
+
+static inline void vdma_ctrl_write(struct xilinx_vdma_chan *chan, u32 reg,
+				   u32 value)
+{
+	vdma_write(chan, chan->ctrl_offset + reg, value);
+}
+
+static inline void vdma_ctrl_clr(struct xilinx_vdma_chan *chan, u32 reg,
+				 u32 clr)
+{
+	vdma_ctrl_write(chan, reg, vdma_ctrl_read(chan, reg) & ~clr);
+}
+
+static inline void vdma_ctrl_set(struct xilinx_vdma_chan *chan, u32 reg,
+				 u32 set)
+{
+	vdma_ctrl_write(chan, reg, vdma_ctrl_read(chan, reg) | set);
+}
+
+/* -----------------------------------------------------------------------------
+ * Descriptors and segments alloc and free
+ */
+
+/**
+ * xilinx_vdma_alloc_tx_segment - Allocate transaction segment
+ * @chan: Driver specific VDMA channel
+ *
+ * Return: The allocated segment on success and NULL on failure.
+ */
+static struct xilinx_vdma_tx_segment *
+xilinx_vdma_alloc_tx_segment(struct xilinx_vdma_chan *chan)
+{
+	struct xilinx_vdma_tx_segment *segment;
+	dma_addr_t phys;
+
+	segment = dma_pool_alloc(chan->desc_pool, GFP_ATOMIC, &phys);
+	if (!segment)
+		return NULL;
+
+	memset(segment, 0, sizeof(*segment));
+	segment->phys = phys;
+
+	return segment;
+}
+
+/**
+ * xilinx_vdma_free_tx_segment - Free transaction segment
+ * @chan: Driver specific VDMA channel
+ * @segment: VDMA transaction segment
+ */
+static void xilinx_vdma_free_tx_segment(struct xilinx_vdma_chan *chan,
+					struct xilinx_vdma_tx_segment *segment)
+{
+	dma_pool_free(chan->desc_pool, segment, segment->phys);
+}
+
+/**
+ * xilinx_vdma_tx_descriptor - Allocate transaction descriptor
+ * @chan: Driver specific VDMA channel
+ *
+ * Return: The allocated descriptor on success and NULL on failure.
+ */
+static struct xilinx_vdma_tx_descriptor *
+xilinx_vdma_alloc_tx_descriptor(struct xilinx_vdma_chan *chan)
+{
+	struct xilinx_vdma_tx_descriptor *desc;
+	unsigned long flags;
+
+	if (chan->allocated_desc)
+		return chan->allocated_desc;
+
+	desc = kzalloc(sizeof(*desc), GFP_KERNEL);
+	if (!desc)
+		return NULL;
+
+	spin_lock_irqsave(&chan->lock, flags);
+	chan->allocated_desc = desc;
+	spin_unlock_irqrestore(&chan->lock, flags);
+
+	INIT_LIST_HEAD(&desc->segments);
+
+	return desc;
+}
+
+/**
+ * xilinx_vdma_free_tx_descriptor - Free transaction descriptor
+ * @chan: Driver specific VDMA channel
+ * @desc: VDMA transaction descriptor
+ */
+static void
+xilinx_vdma_free_tx_descriptor(struct xilinx_vdma_chan *chan,
+			       struct xilinx_vdma_tx_descriptor *desc)
+{
+	struct xilinx_vdma_tx_segment *segment, *next;
+
+	if (!desc)
+		return;
+
+	list_for_each_entry_safe(segment, next, &desc->segments, node) {
+		list_del(&segment->node);
+		xilinx_vdma_free_tx_segment(chan, segment);
+	}
+
+	kfree(desc);
+}
+
+/* Required functions */
+
+/**
+ * xilinx_vdma_free_desc_list - Free descriptors list
+ * @chan: Driver specific VDMA channel
+ * @list: List to parse and delete the descriptor
+ */
+static void xilinx_vdma_free_desc_list(struct xilinx_vdma_chan *chan,
+					struct list_head *list)
+{
+	struct xilinx_vdma_tx_descriptor *desc, *next;
+
+	list_for_each_entry_safe(desc, next, list, node) {
+		list_del(&desc->node);
+		xilinx_vdma_free_tx_descriptor(chan, desc);
+	}
+}
+
+/**
+ * xilinx_vdma_free_descriptors - Free channel descriptors
+ * @chan: Driver specific VDMA channel
+ */
+static void xilinx_vdma_free_descriptors(struct xilinx_vdma_chan *chan)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	xilinx_vdma_free_desc_list(chan, &chan->pending_list);
+	xilinx_vdma_free_desc_list(chan, &chan->done_list);
+
+	xilinx_vdma_free_tx_descriptor(chan, chan->active_desc);
+	chan->active_desc = NULL;
+
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * xilinx_vdma_free_chan_resources - Free channel resources
+ * @dchan: DMA channel
+ */
+static void xilinx_vdma_free_chan_resources(struct dma_chan *dchan)
+{
+	struct xilinx_vdma_chan *chan = to_xilinx_chan(dchan);
+
+	dev_dbg(chan->dev, "Free all channel resources.\n");
+
+	xilinx_vdma_free_descriptors(chan);
+	dma_pool_destroy(chan->desc_pool);
+	chan->desc_pool = NULL;
+}
+
+/**
+ * xilinx_vdma_chan_desc_cleanup - Clean channel descriptors
+ * @chan: Driver specific VDMA channel
+ */
+static void xilinx_vdma_chan_desc_cleanup(struct xilinx_vdma_chan *chan)
+{
+	struct xilinx_vdma_tx_descriptor *desc, *next;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	list_for_each_entry_safe(desc, next, &chan->done_list, node) {
+		dma_async_tx_callback callback;
+		void *callback_param;
+
+		/* Remove from the list of running transactions */
+		list_del(&desc->node);
+
+		/* Run the link descriptor callback function */
+		callback = desc->async_tx.callback;
+		callback_param = desc->async_tx.callback_param;
+		if (callback) {
+			spin_unlock_irqrestore(&chan->lock, flags);
+			callback(callback_param);
+			spin_lock_irqsave(&chan->lock, flags);
+		}
+
+		/* Run any dependencies, then free the descriptor */
+		dma_run_dependencies(&desc->async_tx);
+		xilinx_vdma_free_tx_descriptor(chan, desc);
+	}
+
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * xilinx_vdma_do_tasklet - Schedule completion tasklet
+ * @data: Pointer to the Xilinx VDMA channel structure
+ */
+static void xilinx_vdma_do_tasklet(unsigned long data)
+{
+	struct xilinx_vdma_chan *chan = (struct xilinx_vdma_chan *)data;
+
+	xilinx_vdma_chan_desc_cleanup(chan);
+}
+
+/**
+ * xilinx_vdma_alloc_chan_resources - Allocate channel resources
+ * @dchan: DMA channel
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_vdma_alloc_chan_resources(struct dma_chan *dchan)
+{
+	struct xilinx_vdma_chan *chan = to_xilinx_chan(dchan);
+
+	/* Has this channel already been allocated? */
+	if (chan->desc_pool)
+		return 0;
+
+	/*
+	 * We need the descriptor to be aligned to 64bytes
+	 * for meeting Xilinx VDMA specification requirement.
+	 */
+	chan->desc_pool = dma_pool_create("xilinx_vdma_desc_pool",
+				chan->dev,
+				sizeof(struct xilinx_vdma_tx_segment),
+				__alignof__(struct xilinx_vdma_tx_segment), 0);
+	if (!chan->desc_pool) {
+		dev_err(chan->dev,
+			"unable to allocate channel %d descriptor pool\n",
+			chan->id);
+		return -ENOMEM;
+	}
+
+	dma_cookie_init(dchan);
+	return 0;
+}
+
+/**
+ * xilinx_vdma_tx_status - Get VDMA transaction status
+ * @dchan: DMA channel
+ * @cookie: Transaction identifier
+ * @txstate: Transaction state
+ *
+ * Return: DMA transaction status
+ */
+static enum dma_status xilinx_vdma_tx_status(struct dma_chan *dchan,
+					dma_cookie_t cookie,
+					struct dma_tx_state *txstate)
+{
+	return dma_cookie_status(dchan, cookie, txstate);
+}
+
+/**
+ * xilinx_vdma_is_running - Check if VDMA channel is running
+ * @chan: Driver specific VDMA channel
+ *
+ * Return: '1' if running, '0' if not.
+ */
+static bool xilinx_vdma_is_running(struct xilinx_vdma_chan *chan)
+{
+	return !(vdma_ctrl_read(chan, XILINX_VDMA_REG_DMASR) &
+		 XILINX_VDMA_DMASR_HALTED) &&
+		(vdma_ctrl_read(chan, XILINX_VDMA_REG_DMACR) &
+		 XILINX_VDMA_DMACR_RUNSTOP);
+}
+
+/**
+ * xilinx_vdma_is_idle - Check if VDMA channel is idle
+ * @chan: Driver specific VDMA channel
+ *
+ * Return: '1' if idle, '0' if not.
+ */
+static bool xilinx_vdma_is_idle(struct xilinx_vdma_chan *chan)
+{
+	return vdma_ctrl_read(chan, XILINX_VDMA_REG_DMASR) &
+		XILINX_VDMA_DMASR_IDLE;
+}
+
+/**
+ * xilinx_vdma_halt - Halt VDMA channel
+ * @chan: Driver specific VDMA channel
+ */
+static void xilinx_vdma_halt(struct xilinx_vdma_chan *chan)
+{
+	int loop = XILINX_VDMA_LOOP_COUNT;
+
+	vdma_ctrl_clr(chan, XILINX_VDMA_REG_DMACR, XILINX_VDMA_DMACR_RUNSTOP);
+
+	/* Wait for the hardware to halt */
+	do {
+		if (vdma_ctrl_read(chan, XILINX_VDMA_REG_DMASR) &
+		    XILINX_VDMA_DMASR_HALTED)
+			break;
+	} while (loop--);
+
+	if (!loop) {
+		dev_err(chan->dev, "Cannot stop channel %p: %x\n",
+			chan, vdma_ctrl_read(chan, XILINX_VDMA_REG_DMASR));
+		chan->err = true;
+	}
+
+	return;
+}
+
+/**
+ * xilinx_vdma_start - Start VDMA channel
+ * @chan: Driver specific VDMA channel
+ */
+static void xilinx_vdma_start(struct xilinx_vdma_chan *chan)
+{
+	int loop = XILINX_VDMA_LOOP_COUNT;
+
+	vdma_ctrl_set(chan, XILINX_VDMA_REG_DMACR, XILINX_VDMA_DMACR_RUNSTOP);
+
+	/* Wait for the hardware to start */
+	do {
+		if (!(vdma_ctrl_read(chan, XILINX_VDMA_REG_DMASR) &
+		      XILINX_VDMA_DMASR_HALTED))
+			break;
+	} while (loop--);
+
+	if (!loop) {
+		dev_err(chan->dev, "Cannot start channel %p: %x\n",
+			chan, vdma_ctrl_read(chan, XILINX_VDMA_REG_DMASR));
+
+		chan->err = true;
+	}
+
+	return;
+}
+
+/**
+ * xilinx_vdma_start_transfer - Starts VDMA transfer
+ * @chan: Driver specific channel struct pointer
+ */
+static void xilinx_vdma_start_transfer(struct xilinx_vdma_chan *chan)
+{
+	struct xilinx_vdma_config *config = &chan->config;
+	struct xilinx_vdma_tx_descriptor *desc;
+	unsigned long flags;
+	u32 reg;
+	struct xilinx_vdma_tx_segment *head, *tail = NULL;
+
+	if (chan->err)
+		return;
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	/* There's already an active descriptor, bail out. */
+	if (chan->active_desc)
+		goto out_unlock;
+
+	if (list_empty(&chan->pending_list))
+		goto out_unlock;
+
+	desc = list_first_entry(&chan->pending_list,
+				struct xilinx_vdma_tx_descriptor, node);
+
+	/* If it is SG mode and hardware is busy, cannot submit */
+	if (chan->has_sg && xilinx_vdma_is_running(chan) &&
+	    !xilinx_vdma_is_idle(chan)) {
+		dev_dbg(chan->dev, "DMA controller still busy\n");
+		goto out_unlock;
+	}
+
+	/*
+	 * If hardware is idle, then all descriptors on the running lists are
+	 * done, start new transfers
+	 */
+	if (chan->has_sg) {
+		head = list_first_entry(&desc->segments,
+					struct xilinx_vdma_tx_segment, node);
+		tail = list_entry(desc->segments.prev,
+				  struct xilinx_vdma_tx_segment, node);
+
+		vdma_ctrl_write(chan, XILINX_VDMA_REG_CURDESC, head->phys);
+	}
+
+	/* Configure the hardware using info in the config structure */
+	reg = vdma_ctrl_read(chan, XILINX_VDMA_REG_DMACR);
+
+	if (config->frm_cnt_en)
+		reg |= XILINX_VDMA_DMACR_FRAMECNT_EN;
+	else
+		reg &= ~XILINX_VDMA_DMACR_FRAMECNT_EN;
+
+	/*
+	 * With SG, start with circular mode, so that BDs can be fetched.
+	 * In direct register mode, if not parking, enable circular mode
+	 */
+	if (chan->has_sg || !config->park)
+		reg |= XILINX_VDMA_DMACR_CIRC_EN;
+
+	if (config->park)
+		reg &= ~XILINX_VDMA_DMACR_CIRC_EN;
+
+	vdma_ctrl_write(chan, XILINX_VDMA_REG_DMACR, reg);
+
+	if (config->park && (config->park_frm >= 0) &&
+			(config->park_frm < chan->num_frms)) {
+		if (chan->direction == DMA_MEM_TO_DEV)
+			vdma_write(chan, XILINX_VDMA_REG_PARK_PTR,
+				config->park_frm <<
+					XILINX_VDMA_PARK_PTR_RD_REF_SHIFT);
+		else
+			vdma_write(chan, XILINX_VDMA_REG_PARK_PTR,
+				config->park_frm <<
+					XILINX_VDMA_PARK_PTR_WR_REF_SHIFT);
+	}
+
+	/* Start the hardware */
+	xilinx_vdma_start(chan);
+
+	if (chan->err)
+		goto out_unlock;
+
+	/* Start the transfer */
+	if (chan->has_sg) {
+		vdma_ctrl_write(chan, XILINX_VDMA_REG_TAILDESC, tail->phys);
+	} else {
+		struct xilinx_vdma_tx_segment *segment, *last = NULL;
+		int i = 0;
+
+		list_for_each_entry(segment, &desc->segments, node) {
+			vdma_desc_write(chan,
+					XILINX_VDMA_REG_START_ADDRESS(i++),
+					segment->hw.buf_addr);
+			last = segment;
+		}
+
+		if (!last)
+			goto out_unlock;
+
+		/* HW expects these parameters to be same for one transaction */
+		vdma_desc_write(chan, XILINX_VDMA_REG_HSIZE, last->hw.hsize);
+		vdma_desc_write(chan, XILINX_VDMA_REG_FRMDLY_STRIDE,
+				last->hw.stride);
+		vdma_desc_write(chan, XILINX_VDMA_REG_VSIZE, last->hw.vsize);
+	}
+
+	list_del(&desc->node);
+	chan->active_desc = desc;
+
+out_unlock:
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * xilinx_vdma_issue_pending - Issue pending transactions
+ * @dchan: DMA channel
+ */
+static void xilinx_vdma_issue_pending(struct dma_chan *dchan)
+{
+	struct xilinx_vdma_chan *chan = to_xilinx_chan(dchan);
+
+	xilinx_vdma_start_transfer(chan);
+}
+
+/**
+ * xilinx_vdma_complete_descriptor - Mark the active descriptor as complete
+ * @chan : xilinx DMA channel
+ *
+ * CONTEXT: hardirq
+ */
+static void xilinx_vdma_complete_descriptor(struct xilinx_vdma_chan *chan)
+{
+	struct xilinx_vdma_tx_descriptor *desc;
+	unsigned long flags;
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	desc = chan->active_desc;
+	if (!desc) {
+		dev_dbg(chan->dev, "no running descriptors\n");
+		goto out_unlock;
+	}
+
+	dma_cookie_complete(&desc->async_tx);
+	list_add_tail(&desc->node, &chan->done_list);
+
+	chan->active_desc = NULL;
+
+out_unlock:
+	spin_unlock_irqrestore(&chan->lock, flags);
+}
+
+/**
+ * xilinx_vdma_reset - Reset VDMA channel
+ * @chan: Driver specific VDMA channel
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_vdma_reset(struct xilinx_vdma_chan *chan)
+{
+	int loop = XILINX_VDMA_LOOP_COUNT;
+	u32 tmp;
+
+	vdma_ctrl_set(chan, XILINX_VDMA_REG_DMACR, XILINX_VDMA_DMACR_RESET);
+
+	tmp = vdma_ctrl_read(chan, XILINX_VDMA_REG_DMACR) &
+		XILINX_VDMA_DMACR_RESET;
+
+	/* Wait for the hardware to finish reset */
+	do {
+		tmp = vdma_ctrl_read(chan, XILINX_VDMA_REG_DMACR) &
+			XILINX_VDMA_DMACR_RESET;
+	} while (loop-- && tmp);
+
+	if (!loop) {
+		dev_err(chan->dev, "reset timeout, cr %x, sr %x\n",
+			vdma_ctrl_read(chan, XILINX_VDMA_REG_DMACR),
+			vdma_ctrl_read(chan, XILINX_VDMA_REG_DMASR));
+		return -ETIMEDOUT;
+	}
+
+	chan->err = false;
+
+	return 0;
+}
+
+/**
+ * xilinx_vdma_chan_reset - Reset VDMA channel and enable interrupts
+ * @chan: Driver specific VDMA channel
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_vdma_chan_reset(struct xilinx_vdma_chan *chan)
+{
+	int err;
+
+	/* Reset VDMA */
+	err = xilinx_vdma_reset(chan);
+	if (err)
+		return err;
+
+	/* Enable interrupts */
+	vdma_ctrl_set(chan, XILINX_VDMA_REG_DMACR,
+		      XILINX_VDMA_DMAXR_ALL_IRQ_MASK);
+
+	return 0;
+}
+
+/**
+ * xilinx_vdma_irq_handler - VDMA Interrupt handler
+ * @irq: IRQ number
+ * @data: Pointer to the Xilinx VDMA channel structure
+ *
+ * Return: IRQ_HANDLED/IRQ_NONE
+ */
+static irqreturn_t xilinx_vdma_irq_handler(int irq, void *data)
+{
+	struct xilinx_vdma_chan *chan = data;
+	u32 status;
+
+	/* Read the status and ack the interrupts. */
+	status = vdma_ctrl_read(chan, XILINX_VDMA_REG_DMASR);
+	if (!(status & XILINX_VDMA_DMAXR_ALL_IRQ_MASK))
+		return IRQ_NONE;
+
+	vdma_ctrl_write(chan, XILINX_VDMA_REG_DMASR,
+			status & XILINX_VDMA_DMAXR_ALL_IRQ_MASK);
+
+	if (status & XILINX_VDMA_DMASR_ERR_IRQ) {
+		/*
+		 * An error occurred. If C_FLUSH_ON_FSYNC is enabled and the
+		 * error is recoverable, ignore it. Otherwise flag the error.
+		 *
+		 * Only recoverable errors can be cleared in the DMASR register,
+		 * make sure not to write to other error bits to 1.
+		 */
+		u32 errors = status & XILINX_VDMA_DMASR_ALL_ERR_MASK;
+		vdma_ctrl_write(chan, XILINX_VDMA_REG_DMASR,
+				errors & XILINX_VDMA_DMASR_ERR_RECOVER_MASK);
+
+		if (!chan->flush_on_fsync ||
+		    (errors & ~XILINX_VDMA_DMASR_ERR_RECOVER_MASK)) {
+			dev_err(chan->dev,
+				"Channel %p has errors %x, cdr %x tdr %x\n",
+				chan, errors,
+				vdma_ctrl_read(chan, XILINX_VDMA_REG_CURDESC),
+				vdma_ctrl_read(chan, XILINX_VDMA_REG_TAILDESC));
+			chan->err = true;
+		}
+	}
+
+	if (status & XILINX_VDMA_DMASR_DLY_CNT_IRQ) {
+		/*
+		 * Device takes too long to do the transfer when user requires
+		 * responsiveness.
+		 */
+		dev_dbg(chan->dev, "Inter-packet latency too long\n");
+	}
+
+	if (status & XILINX_VDMA_DMASR_FRM_CNT_IRQ) {
+		xilinx_vdma_complete_descriptor(chan);
+		xilinx_vdma_start_transfer(chan);
+	}
+
+	tasklet_schedule(&chan->tasklet);
+	return IRQ_HANDLED;
+}
+
+/**
+ * xilinx_vdma_tx_submit - Submit DMA transaction
+ * @tx: Async transaction descriptor
+ *
+ * Return: cookie value on success and failure value on error
+ */
+static dma_cookie_t xilinx_vdma_tx_submit(struct dma_async_tx_descriptor *tx)
+{
+	struct xilinx_vdma_tx_descriptor *desc = to_vdma_tx_descriptor(tx);
+	struct xilinx_vdma_chan *chan = to_xilinx_chan(tx->chan);
+	dma_cookie_t cookie;
+	unsigned long flags;
+	int err;
+
+	if (chan->err) {
+		/*
+		 * If reset fails, need to hard reset the system.
+		 * Channel is no longer functional
+		 */
+		err = xilinx_vdma_chan_reset(chan);
+		if (err < 0)
+			return err;
+	}
+
+	spin_lock_irqsave(&chan->lock, flags);
+
+	cookie = dma_cookie_assign(tx);
+
+	/* Append the transaction to the pending transactions queue. */
+	list_add_tail(&desc->node, &chan->pending_list);
+
+	/* Free the allocated desc */
+	chan->allocated_desc = NULL;
+
+	spin_unlock_irqrestore(&chan->lock, flags);
+
+	return cookie;
+}
+
+/**
+ * xilinx_vdma_dma_prep_interleaved - prepare a descriptor for a
+ *	DMA_SLAVE transaction
+ * @dchan: DMA channel
+ * @xt: Interleaved template pointer
+ * @flags: transfer ack flags
+ *
+ * Return: Async transaction descriptor on success and NULL on failure
+ */
+static struct dma_async_tx_descriptor *
+xilinx_vdma_dma_prep_interleaved(struct dma_chan *dchan,
+				 struct dma_interleaved_template *xt,
+				 unsigned long flags)
+{
+	struct xilinx_vdma_chan *chan = to_xilinx_chan(dchan);
+	struct xilinx_vdma_tx_descriptor *desc;
+	struct xilinx_vdma_tx_segment *segment, *prev = NULL;
+	struct xilinx_vdma_desc_hw *hw;
+
+	if (!is_slave_direction(xt->dir))
+		return NULL;
+
+	if (!xt->numf || !xt->sgl[0].size)
+		return NULL;
+
+	/* Allocate a transaction descriptor. */
+	desc = xilinx_vdma_alloc_tx_descriptor(chan);
+	if (!desc)
+		return NULL;
+
+	dma_async_tx_descriptor_init(&desc->async_tx, &chan->common);
+	desc->async_tx.tx_submit = xilinx_vdma_tx_submit;
+	async_tx_ack(&desc->async_tx);
+
+	/* Allocate the link descriptor from DMA pool */
+	segment = xilinx_vdma_alloc_tx_segment(chan);
+	if (!segment)
+		goto error;
+
+	/* Fill in the hardware descriptor */
+	hw = &segment->hw;
+	hw->vsize = xt->numf;
+	hw->hsize = xt->sgl[0].size;
+	hw->stride = xt->sgl[0].icg <<
+			XILINX_VDMA_FRMDLY_STRIDE_STRIDE_SHIFT;
+	hw->stride |= chan->config.frm_dly <<
+			XILINX_VDMA_FRMDLY_STRIDE_FRMDLY_SHIFT;
+
+	if (xt->dir != DMA_MEM_TO_DEV)
+		hw->buf_addr = xt->dst_start;
+	else
+		hw->buf_addr = xt->src_start;
+
+	/* Link the previous next descriptor to current */
+	prev = list_last_entry(&desc->segments,
+				struct xilinx_vdma_tx_segment, node);
+	prev->hw.next_desc = segment->phys;
+
+	/* Insert the segment into the descriptor segments list. */
+	list_add_tail(&segment->node, &desc->segments);
+
+	prev = segment;
+
+	/* Link the last hardware descriptor with the first. */
+	segment = list_first_entry(&desc->segments,
+				   struct xilinx_vdma_tx_segment, node);
+	prev->hw.next_desc = segment->phys;
+
+	return &desc->async_tx;
+
+error:
+	xilinx_vdma_free_tx_descriptor(chan, desc);
+	return NULL;
+}
+
+/**
+ * xilinx_vdma_terminate_all - Halt the channel and free descriptors
+ * @chan: Driver specific VDMA Channel pointer
+ */
+static void xilinx_vdma_terminate_all(struct xilinx_vdma_chan *chan)
+{
+	/* Halt the DMA engine */
+	xilinx_vdma_halt(chan);
+
+	/* Remove and free all of the descriptors in the lists */
+	xilinx_vdma_free_descriptors(chan);
+}
+
+/**
+ * xilinx_vdma_channel_set_config - Configure VDMA channel
+ * Run-time configuration for Axi VDMA, supports:
+ * . halt the channel
+ * . configure interrupt coalescing and inter-packet delay threshold
+ * . start/stop parking
+ * . enable genlock
+ *
+ * @dchan: DMA channel
+ * @cfg: VDMA device configuration pointer
+ *
+ * Return: '0' on success and failure value on error
+ */
+int xilinx_vdma_channel_set_config(struct dma_chan *dchan,
+					struct xilinx_vdma_config *cfg)
+{
+	struct xilinx_vdma_chan *chan = to_xilinx_chan(dchan);
+	u32 dmacr;
+
+	if (cfg->reset)
+		return xilinx_vdma_chan_reset(chan);
+
+	dmacr = vdma_ctrl_read(chan, XILINX_VDMA_REG_DMACR);
+
+	chan->config.frm_dly = cfg->frm_dly;
+	chan->config.park = cfg->park;
+
+	/* genlock settings */
+	chan->config.gen_lock = cfg->gen_lock;
+	chan->config.master = cfg->master;
+
+	if (cfg->gen_lock && chan->genlock) {
+		dmacr |= XILINX_VDMA_DMACR_GENLOCK_EN;
+		dmacr |= cfg->master << XILINX_VDMA_DMACR_MASTER_SHIFT;
+	}
+
+	chan->config.frm_cnt_en = cfg->frm_cnt_en;
+	if (cfg->park)
+		chan->config.park_frm = cfg->park_frm;
+	else
+		chan->config.park_frm = -1;
+
+	chan->config.coalesc = cfg->coalesc;
+	chan->config.delay = cfg->delay;
+
+	if (cfg->coalesc <= XILINX_VDMA_DMACR_FRAME_COUNT_MAX) {
+		dmacr |= cfg->coalesc << XILINX_VDMA_DMACR_FRAME_COUNT_SHIFT;
+		chan->config.coalesc = cfg->coalesc;
+	}
+
+	if (cfg->delay <= XILINX_VDMA_DMACR_DELAY_MAX) {
+		dmacr |= cfg->delay << XILINX_VDMA_DMACR_DELAY_SHIFT;
+		chan->config.delay = cfg->delay;
+	}
+
+	/* FSync Source selection */
+	dmacr &= ~XILINX_VDMA_DMACR_FSYNCSRC_MASK;
+	dmacr |= cfg->ext_fsync << XILINX_VDMA_DMACR_FSYNCSRC_SHIFT;
+
+	vdma_ctrl_write(chan, XILINX_VDMA_REG_DMACR, dmacr);
+
+	return 0;
+}
+EXPORT_SYMBOL(xilinx_vdma_channel_set_config);
+
+/**
+ * xilinx_vdma_device_control - Configure DMA channel of the device
+ * @dchan: DMA Channel pointer
+ * @cmd: DMA control command
+ * @arg: Channel configuration
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_vdma_device_control(struct dma_chan *dchan,
+				      enum dma_ctrl_cmd cmd, unsigned long arg)
+{
+	struct xilinx_vdma_chan *chan = to_xilinx_chan(dchan);
+
+	if (cmd != DMA_TERMINATE_ALL)
+		return -ENXIO;
+
+	xilinx_vdma_terminate_all(chan);
+
+	return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * Probe and remove
+ */
+
+/**
+ * xilinx_vdma_chan_remove - Per Channel remove function
+ * @chan: Driver specific VDMA channel
+ */
+static void xilinx_vdma_chan_remove(struct xilinx_vdma_chan *chan)
+{
+	/* Disable all interrupts */
+	vdma_ctrl_clr(chan, XILINX_VDMA_REG_DMACR,
+		      XILINX_VDMA_DMAXR_ALL_IRQ_MASK);
+
+	if (chan->irq > 0)
+		free_irq(chan->irq, chan);
+
+	tasklet_kill(&chan->tasklet);
+
+	list_del(&chan->common.device_node);
+}
+
+/**
+ * xilinx_vdma_chan_probe - Per Channel Probing
+ * It get channel features from the device tree entry and
+ * initialize special channel handling routines
+ *
+ * @xdev: Driver specific device structure
+ * @node: Device node
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_vdma_chan_probe(struct xilinx_vdma_device *xdev,
+				  struct device_node *node)
+{
+	struct xilinx_vdma_chan *chan;
+	bool has_dre = false;
+	u32 value, width;
+	int err;
+
+	/* Allocate and initialize the channel structure */
+	chan = devm_kzalloc(xdev->dev, sizeof(*chan), GFP_KERNEL);
+	if (!chan)
+		return -ENOMEM;
+
+	chan->dev = xdev->dev;
+	chan->xdev = xdev;
+	chan->has_sg = xdev->has_sg;
+
+	spin_lock_init(&chan->lock);
+	INIT_LIST_HEAD(&chan->pending_list);
+	INIT_LIST_HEAD(&chan->done_list);
+
+	/* Retrieve the channel properties from the device tree */
+	has_dre = of_property_read_bool(node, "xlnx,include-dre");
+
+	chan->genlock = of_property_read_bool(node, "xlnx,genlock-mode");
+
+	err = of_property_read_u32(node, "xlnx,datawidth", &value);
+	if (err) {
+		dev_err(xdev->dev, "missing xlnx,datawidth property\n");
+		return err;
+	}
+	width = value >> 3; /* Convert bits to bytes */
+
+	/* If data width is greater than 8 bytes, DRE is not in hw */
+	if (width > 8)
+		has_dre = false;
+
+	if (!has_dre)
+		xdev->common.copy_align = fls(width - 1);
+
+	if (of_device_is_compatible(node, "xlnx,axi-vdma-mm2s-channel")) {
+		chan->direction = DMA_MEM_TO_DEV;
+		chan->id = 0;
+
+		chan->ctrl_offset = XILINX_VDMA_MM2S_CTRL_OFFSET;
+		chan->desc_offset = XILINX_VDMA_MM2S_DESC_OFFSET;
+
+		if (xdev->flush_on_fsync == XILINX_VDMA_FLUSH_BOTH ||
+		    xdev->flush_on_fsync == XILINX_VDMA_FLUSH_MM2S)
+			chan->flush_on_fsync = true;
+	} else if (of_device_is_compatible(node,
+					    "xlnx,axi-vdma-s2mm-channel")) {
+		chan->direction = DMA_DEV_TO_MEM;
+		chan->id = 1;
+
+		chan->ctrl_offset = XILINX_VDMA_S2MM_CTRL_OFFSET;
+		chan->desc_offset = XILINX_VDMA_S2MM_DESC_OFFSET;
+
+		if (xdev->flush_on_fsync == XILINX_VDMA_FLUSH_BOTH ||
+		    xdev->flush_on_fsync == XILINX_VDMA_FLUSH_S2MM)
+			chan->flush_on_fsync = true;
+	} else {
+		dev_err(xdev->dev, "Invalid channel compatible node\n");
+		return -EINVAL;
+	}
+
+	/* Request the interrupt */
+	chan->irq = irq_of_parse_and_map(node, 0);
+	err = request_irq(chan->irq, xilinx_vdma_irq_handler, IRQF_SHARED,
+			  "xilinx-vdma-controller", chan);
+	if (err) {
+		dev_err(xdev->dev, "unable to request IRQ %d\n", chan->irq);
+		return err;
+	}
+
+	/* Initialize the tasklet */
+	tasklet_init(&chan->tasklet, xilinx_vdma_do_tasklet,
+			(unsigned long)chan);
+
+	/*
+	 * Initialize the DMA channel and add it to the DMA engine channels
+	 * list.
+	 */
+	chan->common.device = &xdev->common;
+
+	list_add_tail(&chan->common.device_node, &xdev->common.channels);
+	xdev->chan[chan->id] = chan;
+
+	/* Reset the channel */
+	err = xilinx_vdma_chan_reset(chan);
+	if (err < 0) {
+		dev_err(xdev->dev, "Reset channel failed\n");
+		return err;
+	}
+
+	return 0;
+}
+
+/**
+ * of_dma_xilinx_xlate - Translation function
+ * @dma_spec: Pointer to DMA specifier as found in the device tree
+ * @ofdma: Pointer to DMA controller data
+ *
+ * Return: DMA channel pointer on success and NULL on error
+ */
+static struct dma_chan *of_dma_xilinx_xlate(struct of_phandle_args *dma_spec,
+						struct of_dma *ofdma)
+{
+	struct xilinx_vdma_device *xdev = ofdma->of_dma_data;
+	int chan_id = dma_spec->args[0];
+
+	if (chan_id >= XILINX_VDMA_MAX_CHANS_PER_DEVICE)
+		return NULL;
+
+	return dma_get_slave_channel(&xdev->chan[chan_id]->common);
+}
+
+/**
+ * xilinx_vdma_probe - Driver probe function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * Return: '0' on success and failure value on error
+ */
+static int xilinx_vdma_probe(struct platform_device *pdev)
+{
+	struct device_node *node = pdev->dev.of_node;
+	struct xilinx_vdma_device *xdev;
+	struct device_node *child;
+	struct resource *io;
+	u32 num_frames;
+	int i, err;
+
+	/* Allocate and initialize the DMA engine structure */
+	xdev = devm_kzalloc(&pdev->dev, sizeof(*xdev), GFP_KERNEL);
+	if (!xdev)
+		return -ENOMEM;
+
+	xdev->dev = &pdev->dev;
+
+	/* Request and map I/O memory */
+	io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xdev->regs = devm_ioremap_resource(&pdev->dev, io);
+	if (IS_ERR(xdev->regs))
+		return PTR_ERR(xdev->regs);
+
+	/* Retrieve the DMA engine properties from the device tree */
+	xdev->has_sg = of_property_read_bool(node, "xlnx,include-sg");
+
+	err = of_property_read_u32(node, "xlnx,num-fstores", &num_frames);
+	if (err < 0) {
+		dev_err(xdev->dev, "missing xlnx,num-fstores property\n");
+		return err;
+	}
+
+	err = of_property_read_u32(node, "xlnx,flush-fsync",
+					&xdev->flush_on_fsync);
+	if (err < 0)
+		dev_warn(xdev->dev, "missing xlnx,flush-fsync property\n");
+
+	/* Initialize the DMA engine */
+	xdev->common.dev = &pdev->dev;
+
+	INIT_LIST_HEAD(&xdev->common.channels);
+	dma_cap_set(DMA_SLAVE, xdev->common.cap_mask);
+	dma_cap_set(DMA_PRIVATE, xdev->common.cap_mask);
+
+	xdev->common.device_alloc_chan_resources =
+				xilinx_vdma_alloc_chan_resources;
+	xdev->common.device_free_chan_resources =
+				xilinx_vdma_free_chan_resources;
+	xdev->common.device_prep_interleaved_dma =
+				xilinx_vdma_dma_prep_interleaved;
+	xdev->common.device_control = xilinx_vdma_device_control;
+	xdev->common.device_tx_status = xilinx_vdma_tx_status;
+	xdev->common.device_issue_pending = xilinx_vdma_issue_pending;
+
+	platform_set_drvdata(pdev, xdev);
+
+	/* Initialize the channels */
+	for_each_child_of_node(node, child) {
+		err = xilinx_vdma_chan_probe(xdev, child);
+		if (err < 0)
+			goto error;
+	}
+
+	for (i = 0; i < XILINX_VDMA_MAX_CHANS_PER_DEVICE; i++)
+		if (xdev->chan[i])
+			xdev->chan[i]->num_frms = num_frames;
+
+	/* Register the DMA engine with the core */
+	dma_async_device_register(&xdev->common);
+
+	err = of_dma_controller_register(node, of_dma_xilinx_xlate,
+					 xdev);
+	if (err < 0) {
+		dev_err(&pdev->dev, "Unable to register DMA to DT\n");
+		dma_async_device_unregister(&xdev->common);
+		goto error;
+	}
+
+	dev_info(&pdev->dev, "Xilinx AXI VDMA Engine Driver Probed!!\n");
+
+	return 0;
+
+error:
+	for (i = 0; i < XILINX_VDMA_MAX_CHANS_PER_DEVICE; i++)
+		if (xdev->chan[i])
+			xilinx_vdma_chan_remove(xdev->chan[i]);
+
+	return err;
+}
+
+/**
+ * xilinx_vdma_remove - Driver remove function
+ * @pdev: Pointer to the platform_device structure
+ *
+ * Return: Always '0'
+ */
+static int xilinx_vdma_remove(struct platform_device *pdev)
+{
+	struct xilinx_vdma_device *xdev = platform_get_drvdata(pdev);
+	int i;
+
+	of_dma_controller_free(pdev->dev.of_node);
+
+	dma_async_device_unregister(&xdev->common);
+
+	for (i = 0; i < XILINX_VDMA_MAX_CHANS_PER_DEVICE; i++)
+		if (xdev->chan[i])
+			xilinx_vdma_chan_remove(xdev->chan[i]);
+
+	return 0;
+}
+
+static const struct of_device_id xilinx_vdma_of_ids[] = {
+	{ .compatible = "xlnx,axi-vdma-1.00.a",},
+	{}
+};
+
+static struct platform_driver xilinx_vdma_driver = {
+	.driver = {
+		.name = "xilinx-vdma",
+		.owner = THIS_MODULE,
+		.of_match_table = xilinx_vdma_of_ids,
+	},
+	.probe = xilinx_vdma_probe,
+	.remove = xilinx_vdma_remove,
+};
+
+module_platform_driver(xilinx_vdma_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("Xilinx VDMA driver");
+MODULE_LICENSE("GPL v2");

include/linux/amba/xilinx_dma.h

+/*
+ * Xilinx DMA Engine drivers support header file
+ *
+ * Copyright (C) 2010-2014 Xilinx, Inc. All rights reserved.
+ *
+ * This is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __DMA_XILINX_DMA_H
+#define __DMA_XILINX_DMA_H
+
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+
+/**
+ * struct xilinx_vdma_config - VDMA Configuration structure
+ * @frm_dly: Frame delay
+ * @gen_lock: Whether in gen-lock mode
+ * @master: Master that it syncs to
+ * @frm_cnt_en: Enable frame count enable
+ * @park: Whether wants to park
+ * @park_frm: Frame to park on
+ * @coalesc: Interrupt coalescing threshold
+ * @delay: Delay counter
+ * @reset: Reset Channel
+ * @ext_fsync: External Frame Sync source
+ */
+struct xilinx_vdma_config {
+	int frm_dly;
+	int gen_lock;
+	int master;
+	int frm_cnt_en;
+	int park;
+	int park_frm;
+	int coalesc;
+	int delay;
+	int reset;
+	int ext_fsync;
+};
+
+int xilinx_vdma_channel_set_config(struct dma_chan *dchan,
+					struct xilinx_vdma_config *cfg);
+
+#endif