Commit 0ada2da5 authored by Kuninori Morimoto's avatar Kuninori Morimoto Committed by Paul Mundt

ARM: mach-shmobile: mackerel: use renesas_usbhs instead of r8a66597_hcd

Current renesas_usbhs driver can use both USB host/gadget.
This patch removes current r8a66597_hcd driver settings,
and adds renesas_usbhs host driver settings for mackerel USB1 port.
You can still use this port as "gadget" with small modify.
Signed-off-by: default avatarKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: default avatarPaul Mundt <lethal@linux-sh.org>
parent c2bc3a31
......@@ -43,7 +43,6 @@
#include <linux/smsc911x.h>
#include <linux/sh_intc.h>
#include <linux/tca6416_keypad.h>
#include <linux/usb/r8a66597.h>
#include <linux/usb/renesas_usbhs.h>
#include <linux/dma-mapping.h>
......@@ -145,11 +144,6 @@
* 1-2 short | VBUS 5V | Host
* open | external VBUS | Function
*
* *1
* CN31 is used as
* CONFIG_USB_R8A66597_HCD Host
* CONFIG_USB_RENESAS_USBHS Function
*
* CAUTION
*
* renesas_usbhs driver can use external interrupt mode
......@@ -161,15 +155,6 @@
* mackerel can not use external interrupt (IRQ7-PORT167) mode on "USB0",
* because Touchscreen is using IRQ7-PORT40.
* It is impossible to use IRQ7 demux on this board.
*
* We can use external interrupt mode USB-Function on "USB1".
* USB1 can become Host by r8a66597, and become Function by renesas_usbhs.
* But don't select both drivers in same time.
* These uses same IRQ number for request_irq(), and aren't supporting
* IRQF_SHARED / IORESOURCE_IRQ_SHAREABLE.
*
* Actually these are old/new version of USB driver.
* This mean its register will be broken if it supports shared IRQ,
*/
/*
......@@ -676,51 +661,16 @@ static struct platform_device usbhs0_device = {
* Use J30 to select between Host and Function. This setting
* can however not be detected by software. Hotplug of USBHS1
* is provided via IRQ8.
*
* Current USB1 works as "USB Host".
* - set J30 "short"
*
* If you want to use it as "USB gadget",
* - J30 "open"
* - modify usbhs1_get_id() USBHS_HOST -> USBHS_GADGET
* - add .get_vbus = usbhs_get_vbus in usbhs1_private
*/
#define IRQ8 evt2irq(0x0300)
/* USBHS1 USB Host support via r8a66597_hcd */
static void usb1_host_port_power(int port, int power)
{
if (!power) /* only power-on is supported for now */
return;
/* set VBOUT/PWEN and EXTLP1 in DVSTCTR */
__raw_writew(__raw_readw(0xE68B0008) | 0x600, 0xE68B0008);
}
static struct r8a66597_platdata usb1_host_data = {
.on_chip = 1,
.port_power = usb1_host_port_power,
};
static struct resource usb1_host_resources[] = {
[0] = {
.name = "USBHS1",
.start = 0xe68b0000,
.end = 0xe68b00e6 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = evt2irq(0x1ce0) /* USB1_USB1I0 */,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device usb1_host_device = {
.name = "r8a66597_hcd",
.id = 1,
.dev = {
.dma_mask = NULL, /* not use dma */
.coherent_dma_mask = 0xffffffff,
.platform_data = &usb1_host_data,
},
.num_resources = ARRAY_SIZE(usb1_host_resources),
.resource = usb1_host_resources,
};
/* USBHS1 USB Function support via renesas_usbhs */
#define USB_PHY_MODE (1 << 4)
#define USB_PHY_INT_EN ((1 << 3) | (1 << 2))
#define USB_PHY_ON (1 << 1)
......@@ -776,7 +726,7 @@ static void usbhs1_hardware_exit(struct platform_device *pdev)
static int usbhs1_get_id(struct platform_device *pdev)
{
return USBHS_GADGET;
return USBHS_HOST;
}
static u32 usbhs1_pipe_cfg[] = {
......@@ -807,7 +757,6 @@ static struct usbhs_private usbhs1_private = {
.hardware_exit = usbhs1_hardware_exit,
.get_id = usbhs1_get_id,
.phy_reset = usbhs_phy_reset,
.get_vbus = usbhs_get_vbus,
},
.driver_param = {
.buswait_bwait = 4,
......@@ -1311,7 +1260,6 @@ static struct platform_device *mackerel_devices[] __initdata = {
&nor_flash_device,
&smc911x_device,
&lcdc_device,
&usb1_host_device,
&usbhs1_device,
&usbhs0_device,
&leds_device,
......@@ -1473,9 +1421,6 @@ static void __init mackerel_init(void)
gpio_pull_down(GPIO_PORT167CR); /* VBUS0_1 pull down */
gpio_request(GPIO_FN_IDIN_1_113, NULL);
/* USB phy tweak to make the r8a66597_hcd host driver work */
__raw_writew(0x8a0a, 0xe6058130); /* USBCR4 */
/* enable FSI2 port A (ak4643) */
gpio_request(GPIO_FN_FSIAIBT, NULL);
gpio_request(GPIO_FN_FSIAILR, NULL);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment