Merge tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes and new device ids for
  4.13-rc5. There is the usual gadget driver fixes, some new quirks for
  "messy" hardware, and some new device ids.

  All have been in linux-next with no reported issues"

* tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: pl2303: add new ATEN device id
  usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter
  USB: Check for dropped connection before switching to full speed
  usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
  usb: renesas_usbhs: gadget: fix unused-but-set-variable warning
  usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3
  usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()
  usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() calling
  usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
  USB: serial: option: add D-Link DWM-222 device ID
  usb: musb: fix tx fifo flush handling again
  usb: core: unlink urbs from the tail of the endpoint's urb_list
  usb-storage: fix deadlock involving host lock and scsi_done
  uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069
  USB: hcd: Mark secondary HCD as dead if the primary one died
  USB: serial: cp210x: add support for Qivicon USB ZigBee dongle

drivers/usb/core/hcd.c

@@ -1888,7 +1888,7 @@ void usb_hcd_flush_endpoint(struct usb_device *udev,
 	/* No more submits can occur */
 	spin_lock_irq(&hcd_urb_list_lock);
 rescan:
-	list_for_each_entry (urb, &ep->urb_list, urb_list) {
+	list_for_each_entry_reverse(urb, &ep->urb_list, urb_list) {
 		int	is_in;
 
 		if (urb->unlinked)
@@ -2485,6 +2485,8 @@ void usb_hc_died (struct usb_hcd *hcd)
 	}
 	if (usb_hcd_is_primary_hcd(hcd) && hcd->shared_hcd) {
 		hcd = hcd->shared_hcd;
+		clear_bit(HCD_FLAG_RH_RUNNING, &hcd->flags);
+		set_bit(HCD_FLAG_DEAD, &hcd->flags);
 		if (hcd->rh_registered) {
 			clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
 

drivers/usb/core/hub.c

@@ -4725,7 +4725,8 @@ hub_power_remaining(struct usb_hub *hub)
 static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus,
 		u16 portchange)
 {
-	int status, i;
+	int status = -ENODEV;
+	int i;
 	unsigned unit_load;
 	struct usb_device *hdev = hub->hdev;
 	struct usb_hcd *hcd = bus_to_hcd(hdev->bus);
@@ -4929,9 +4930,10 @@ static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus,
 
 done:
 	hub_port_disable(hub, port1, 1);
-	if (hcd->driver->relinquish_port && !hub->hdev->parent)
+	if (hcd->driver->relinquish_port && !hub->hdev->parent) {
+		if (status != -ENOTCONN && status != -ENODEV)
 			hcd->driver->relinquish_port(hcd, port1);
-
+	}
 }
 
 /* Handle physical or logical connection change events.

drivers/usb/core/quirks.c

@@ -150,6 +150,9 @@ static const struct usb_device_id usb_quirk_list[] = {
 	/* appletouch */
 	{ USB_DEVICE(0x05ac, 0x021a), .driver_info = USB_QUIRK_RESET_RESUME },
 
+	/* Genesys Logic hub, internally used by Moshi USB to Ethernet Adapter */
+	{ USB_DEVICE(0x05e3, 0x0616), .driver_info = USB_QUIRK_NO_LPM },
+
 	/* Avision AV600U */
 	{ USB_DEVICE(0x0638, 0x0a13), .driver_info =
 	  USB_QUIRK_STRING_FETCH_255 },
@@ -249,6 +252,7 @@ static const struct usb_device_id usb_amd_resume_quirk_list[] = {
 	{ USB_DEVICE(0x093a, 0x2500), .driver_info = USB_QUIRK_RESET_RESUME },
 	{ USB_DEVICE(0x093a, 0x2510), .driver_info = USB_QUIRK_RESET_RESUME },
 	{ USB_DEVICE(0x093a, 0x2521), .driver_info = USB_QUIRK_RESET_RESUME },
+	{ USB_DEVICE(0x03f0, 0x2b4a), .driver_info = USB_QUIRK_RESET_RESUME },
 
 	/* Logitech Optical Mouse M90/M100 */
 	{ USB_DEVICE(0x046d, 0xc05a), .driver_info = USB_QUIRK_RESET_RESUME },

drivers/usb/dwc3/gadget.c

@@ -896,9 +896,40 @@ static void __dwc3_prepare_one_trb(struct dwc3_ep *dep, struct dwc3_trb *trb,
 		if (!node) {
 			trb->ctrl = DWC3_TRBCTL_ISOCHRONOUS_FIRST;
 
+			/*
+			 * USB Specification 2.0 Section 5.9.2 states that: "If
+			 * there is only a single transaction in the microframe,
+			 * only a DATA0 data packet PID is used.  If there are
+			 * two transactions per microframe, DATA1 is used for
+			 * the first transaction data packet and DATA0 is used
+			 * for the second transaction data packet.  If there are
+			 * three transactions per microframe, DATA2 is used for
+			 * the first transaction data packet, DATA1 is used for
+			 * the second, and DATA0 is used for the third."
+			 *
+			 * IOW, we should satisfy the following cases:
+			 *
+			 * 1) length <= maxpacket
+			 *	- DATA0
+			 *
+			 * 2) maxpacket < length <= (2 * maxpacket)
+			 *	- DATA1, DATA0
+			 *
+			 * 3) (2 * maxpacket) < length <= (3 * maxpacket)
+			 *	- DATA2, DATA1, DATA0
+			 */
 			if (speed == USB_SPEED_HIGH) {
 				struct usb_ep *ep = &dep->endpoint;
-				trb->size |= DWC3_TRB_SIZE_PCM1(ep->mult - 1);
+				unsigned int mult = ep->mult - 1;
+				unsigned int maxp = usb_endpoint_maxp(ep->desc);
+
+				if (length <= (2 * maxp))
+					mult--;
+
+				if (length <= maxp)
+					mult--;
+
+				trb->size |= DWC3_TRB_SIZE_PCM1(mult);
 			}
 		} else {
 			trb->ctrl = DWC3_TRBCTL_ISOCHRONOUS;

drivers/usb/gadget/udc/renesas_usb3.c

@@ -838,21 +838,32 @@ static struct renesas_usb3_request *usb3_get_request(struct renesas_usb3_ep
 	return usb3_req;
 }
 
-static void usb3_request_done(struct renesas_usb3_ep *usb3_ep,
-			      struct renesas_usb3_request *usb3_req, int status)
+static void __usb3_request_done(struct renesas_usb3_ep *usb3_ep,
+				struct renesas_usb3_request *usb3_req,
+				int status)
 {
 	struct renesas_usb3 *usb3 = usb3_ep_to_usb3(usb3_ep);
-	unsigned long flags;
 
 	dev_dbg(usb3_to_dev(usb3), "giveback: ep%2d, %u, %u, %d\n",
 		usb3_ep->num, usb3_req->req.length, usb3_req->req.actual,
 		status);
 	usb3_req->req.status = status;
-	spin_lock_irqsave(&usb3->lock, flags);
 	usb3_ep->started = false;
 	list_del_init(&usb3_req->queue);
-	spin_unlock_irqrestore(&usb3->lock, flags);
+	spin_unlock(&usb3->lock);
 	usb_gadget_giveback_request(&usb3_ep->ep, &usb3_req->req);
+	spin_lock(&usb3->lock);
+}
+
+static void usb3_request_done(struct renesas_usb3_ep *usb3_ep,
+			      struct renesas_usb3_request *usb3_req, int status)
+{
+	struct renesas_usb3 *usb3 = usb3_ep_to_usb3(usb3_ep);
+	unsigned long flags;
+
+	spin_lock_irqsave(&usb3->lock, flags);
+	__usb3_request_done(usb3_ep, usb3_req, status);
+	spin_unlock_irqrestore(&usb3->lock, flags);
 }
 
 static void usb3_irq_epc_pipe0_status_end(struct renesas_usb3 *usb3)

drivers/usb/host/pci-quirks.c

@@ -98,6 +98,7 @@ enum amd_chipset_gen {
 	AMD_CHIPSET_HUDSON2,
 	AMD_CHIPSET_BOLTON,
 	AMD_CHIPSET_YANGTZE,
+	AMD_CHIPSET_TAISHAN,
 	AMD_CHIPSET_UNKNOWN,
 };
 
@@ -141,6 +142,11 @@ static int amd_chipset_sb_type_init(struct amd_chipset_info *pinfo)
 			pinfo->sb_type.gen = AMD_CHIPSET_SB700;
 		else if (rev >= 0x40 && rev <= 0x4f)
 			pinfo->sb_type.gen = AMD_CHIPSET_SB800;
+	}
+	pinfo->smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD,
+					  0x145c, NULL);
+	if (pinfo->smbus_dev) {
+		pinfo->sb_type.gen = AMD_CHIPSET_TAISHAN;
 	} else {
 		pinfo->smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD,
 				PCI_DEVICE_ID_AMD_HUDSON2_SMBUS, NULL);
@@ -260,11 +266,12 @@ int usb_hcd_amd_remote_wakeup_quirk(struct pci_dev *pdev)
 {
 	/* Make sure amd chipset type has already been initialized */
 	usb_amd_find_chipset_info();
-	if (amd_chipset.sb_type.gen != AMD_CHIPSET_YANGTZE)
-		return 0;
-
+	if (amd_chipset.sb_type.gen == AMD_CHIPSET_YANGTZE ||
+	    amd_chipset.sb_type.gen == AMD_CHIPSET_TAISHAN) {
 		dev_dbg(&pdev->dev, "QUIRK: Enable AMD remote wakeup fix\n");
 		return 1;
+	}
+	return 0;
 }
 EXPORT_SYMBOL_GPL(usb_hcd_amd_remote_wakeup_quirk);
 

drivers/usb/musb/musb_host.c

@@ -139,6 +139,7 @@ static void musb_h_tx_flush_fifo(struct musb_hw_ep *ep)
 				"Could not flush host TX%d fifo: csr: %04x\n",
 				ep->epnum, csr))
 			return;
+		mdelay(1);
 	}
 }
 

drivers/usb/phy/phy-msm-usb.c

@@ -197,6 +197,7 @@ struct msm_otg {
 	struct regulator *v3p3;
 	struct regulator *v1p8;
 	struct regulator *vddcx;
+	struct regulator_bulk_data supplies[3];
 
 	struct reset_control *phy_rst;
 	struct reset_control *link_rst;
@@ -1731,7 +1732,6 @@ static int msm_otg_reboot_notify(struct notifier_block *this,
 
 static int msm_otg_probe(struct platform_device *pdev)
 {
-	struct regulator_bulk_data regs[3];
 	int ret = 0;
 	struct device_node *np = pdev->dev.of_node;
 	struct msm_otg_platform_data *pdata;
@@ -1817,17 +1817,18 @@ static int msm_otg_probe(struct platform_device *pdev)
 		return motg->irq;
 	}
 
-	regs[0].supply = "vddcx";
-	regs[1].supply = "v3p3";
-	regs[2].supply = "v1p8";
+	motg->supplies[0].supply = "vddcx";
+	motg->supplies[1].supply = "v3p3";
+	motg->supplies[2].supply = "v1p8";
 
-	ret = devm_regulator_bulk_get(motg->phy.dev, ARRAY_SIZE(regs), regs);
+	ret = devm_regulator_bulk_get(motg->phy.dev, ARRAY_SIZE(motg->supplies),
+				      motg->supplies);
 	if (ret)
 		return ret;
 
-	motg->vddcx = regs[0].consumer;
-	motg->v3p3  = regs[1].consumer;
-	motg->v1p8  = regs[2].consumer;
+	motg->vddcx = motg->supplies[0].consumer;
+	motg->v3p3  = motg->supplies[1].consumer;
+	motg->v1p8  = motg->supplies[2].consumer;
 
 	clk_set_rate(motg->clk, 60000000);
 

drivers/usb/renesas_usbhs/mod_gadget.c

@@ -639,14 +639,11 @@ static int usbhsg_ep_disable(struct usb_ep *ep)
 	struct usbhsg_uep *uep = usbhsg_ep_to_uep(ep);
 	struct usbhs_pipe *pipe;
 	unsigned long flags;
-	int ret = 0;
 
 	spin_lock_irqsave(&uep->lock, flags);
 	pipe = usbhsg_uep_to_pipe(uep);
-	if (!pipe) {
-		ret = -EINVAL;
+	if (!pipe)
 		goto out;
-	}
 
 	usbhsg_pipe_disable(uep);
 	usbhs_pipe_free(pipe);

drivers/usb/renesas_usbhs/rcar3.c

@@ -20,9 +20,13 @@
 /* Low Power Status register (LPSTS) */
 #define LPSTS_SUSPM	0x4000
 
-/* USB General control register 2 (UGCTRL2), bit[31:6] should be 0 */
+/*
+ * USB General control register 2 (UGCTRL2)
+ * Remarks: bit[31:11] and bit[9:6] should be 0
+ */
 #define UGCTRL2_RESERVED_3	0x00000001	/* bit[3:0] should be B'0001 */
 #define UGCTRL2_USB0SEL_OTG	0x00000030
+#define UGCTRL2_VBUSSEL		0x00000400
 
 static void usbhs_write32(struct usbhs_priv *priv, u32 reg, u32 data)
 {
@@ -34,7 +38,8 @@ static int usbhs_rcar3_power_ctrl(struct platform_device *pdev,
 {
 	struct usbhs_priv *priv = usbhs_pdev_to_priv(pdev);
 
-	usbhs_write32(priv, UGCTRL2, UGCTRL2_RESERVED_3 | UGCTRL2_USB0SEL_OTG);
+	usbhs_write32(priv, UGCTRL2, UGCTRL2_RESERVED_3 | UGCTRL2_USB0SEL_OTG |
+		      UGCTRL2_VBUSSEL);
 
 	if (enable) {
 		usbhs_bset(priv, LPSTS, LPSTS_SUSPM, LPSTS_SUSPM);

drivers/usb/serial/cp210x.c

@@ -142,6 +142,7 @@ static const struct usb_device_id id_table[] = {
 	{ USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */
 	{ USB_DEVICE(0x10C4, 0x8A2A) }, /* HubZ dual ZigBee and Z-Wave dongle */
 	{ USB_DEVICE(0x10C4, 0x8A5E) }, /* CEL EM3588 ZigBee USB Stick Long Range */
+	{ USB_DEVICE(0x10C4, 0x8B34) }, /* Qivicon ZigBee USB Radio Stick */
 	{ USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
 	{ USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
 	{ USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */

drivers/usb/serial/option.c

@@ -2025,6 +2025,8 @@ static const struct usb_device_id option_ids[] = {
 	{ USB_DEVICE_INTERFACE_CLASS(0x2001, 0x7d04, 0xff) },			/* D-Link DWM-158 */
 	{ USB_DEVICE_INTERFACE_CLASS(0x2001, 0x7e19, 0xff),			/* D-Link DWM-221 B1 */
 	  .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
+	{ USB_DEVICE_INTERFACE_CLASS(0x2001, 0x7e35, 0xff),			/* D-Link DWM-222 */
+	  .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
 	{ USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e01, 0xff, 0xff, 0xff) }, /* D-Link DWM-152/C1 */
 	{ USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e02, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/C1 */
 	{ USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x7e11, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/A3 */

drivers/usb/serial/pl2303.c

@@ -52,6 +52,8 @@ static const struct usb_device_id id_table[] = {
 	{ USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID_RSAQ5) },
 	{ USB_DEVICE(ATEN_VENDOR_ID, ATEN_PRODUCT_ID),
 		.driver_info = PL2303_QUIRK_ENDPOINT_HACK },
+	{ USB_DEVICE(ATEN_VENDOR_ID, ATEN_PRODUCT_UC485),
+		.driver_info = PL2303_QUIRK_ENDPOINT_HACK },
 	{ USB_DEVICE(ATEN_VENDOR_ID, ATEN_PRODUCT_ID2) },
 	{ USB_DEVICE(ATEN_VENDOR_ID2, ATEN_PRODUCT_ID) },
 	{ USB_DEVICE(ELCOM_VENDOR_ID, ELCOM_PRODUCT_ID) },

drivers/usb/serial/pl2303.h

@@ -27,6 +27,7 @@
 #define ATEN_VENDOR_ID		0x0557
 #define ATEN_VENDOR_ID2		0x0547
 #define ATEN_PRODUCT_ID		0x2008
+#define ATEN_PRODUCT_UC485	0x2021
 #define ATEN_PRODUCT_ID2	0x2118
 
 #define IODATA_VENDOR_ID	0x04bb

drivers/usb/storage/unusual_uas.h

@@ -124,9 +124,9 @@ UNUSUAL_DEV(0x0bc2, 0xab2a, 0x0000, 0x9999,
 /* Reported-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> */
 UNUSUAL_DEV(0x13fd, 0x3940, 0x0000, 0x9999,
 		"Initio Corporation",
-		"",
+		"INIC-3069",
 		USB_SC_DEVICE, USB_PR_DEVICE, NULL,
-		US_FL_NO_ATA_1X),
+		US_FL_NO_ATA_1X | US_FL_IGNORE_RESIDUE),
 
 /* Reported-by: Tom Arild Naess <tanaess@gmail.com> */
 UNUSUAL_DEV(0x152d, 0x0539, 0x0000, 0x9999,

drivers/usb/storage/usb.c

@@ -315,6 +315,7 @@ static int usb_stor_control_thread(void * __us)
 {
 	struct us_data *us = (struct us_data *)__us;
 	struct Scsi_Host *host = us_to_host(us);
+	struct scsi_cmnd *srb;
 
 	for (;;) {
 		usb_stor_dbg(us, "*** thread sleeping\n");
@@ -330,6 +331,7 @@ static int usb_stor_control_thread(void * __us)
 		scsi_lock(host);
 
 		/* When we are called with no command pending, we're done */
+		srb = us->srb;
 		if (us->srb == NULL) {
 			scsi_unlock(host);
 			mutex_unlock(&us->dev_mutex);
@@ -398,14 +400,11 @@ static int usb_stor_control_thread(void * __us)
 		/* lock access to the state */
 		scsi_lock(host);
 
-		/* indicate that the command is done */
-		if (us->srb->result != DID_ABORT << 16) {
-			usb_stor_dbg(us, "scsi cmd done, result=0x%x\n",
-				     us->srb->result);
-			us->srb->scsi_done(us->srb);
-		} else {
+		/* was the command aborted? */
+		if (us->srb->result == DID_ABORT << 16) {
 SkipForAbort:
 			usb_stor_dbg(us, "scsi command aborted\n");
+			srb = NULL;	/* Don't call srb->scsi_done() */
 		}
 
 		/*
@@ -429,6 +428,13 @@ static int usb_stor_control_thread(void * __us)
 
 		/* unlock the device pointers */
 		mutex_unlock(&us->dev_mutex);
+
+		/* now that the locks are released, notify the SCSI core */
+		if (srb) {
+			usb_stor_dbg(us, "scsi cmd done, result=0x%x\n",
+					srb->result);
+			srb->scsi_done(srb);
+		}
 	} /* for (;;) */
 
 	/* Wait until we are told to stop */