Commit 115e1adc authored by Bartlomiej Sieka's avatar Bartlomiej Sieka Committed by Paul Mackerras

[POWERPC] mpc5200: Amalgamated DTS fixes and updates

DTS updates that fix booting problems on mpc5200-based boards:
- change to ethernet reg property
- addition of mdio and phy nodes
- removal of pci node (Motion-Pro board)

Other DTS updates:
- update i2c device tree nodes
- add lpb bus node and flash device (without partitions defined)
- add rtc i2c nodes
Signed-off-by: default avatarMarian Balakowicz <m8@semihalf.com>
Acked-by: default avatarGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
parent 74848398
......@@ -212,13 +212,30 @@ serial@2c00 { // PSC6
ethernet@3000 {
device_type = "network";
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
reg = <3000 800>;
reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
phy-handle = <&phy0>;
};
mdio@3000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
reg = <3000 400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
interrupt-parent = <&mpc5200_pic>;
phy0: ethernet-phy@0 {
device_type = "ethernet-phy";
reg = <0>;
};
};
i2c@3d40 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
......@@ -231,4 +248,22 @@ sram@8000 {
reg = <8000 4000>;
};
};
lpb {
model = "fsl,lpb";
compatible = "fsl,lpb";
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 fc000000 2000000>;
// 16-bit flash device at LocalPlus Bus CS0
flash@0,0 {
compatible = "cfi-flash";
reg = <0 0 2000000>;
bank-width = <2>;
device-width = <2>;
#size-cells = <1>;
#address-cells = <1>;
};
};
};
......@@ -148,7 +148,6 @@ gpio@c00 {
interrupt-parent = <&mpc5200_pic>;
};
spi@f00 {
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
reg = <f00 20>;
......@@ -209,10 +208,25 @@ serial@2800 { // PSC5
ethernet@3000 {
device_type = "network";
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
reg = <3000 800>;
reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
phy-handle = <&phy0>;
};
mdio@3000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
reg = <3000 400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
interrupt-parent = <&mpc5200_pic>;
phy0: ethernet-phy@2 {
device_type = "ethernet-phy";
reg = <2>;
};
};
ata@3a00 {
......@@ -223,11 +237,19 @@ ata@3a00 {
};
i2c@3d40 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
rtc@68 {
device_type = "rtc";
compatible = "dallas,ds1339";
reg = <68>;
};
};
sram@8000 {
......@@ -240,7 +262,8 @@ lpb {
compatible = "fsl,lpb";
#address-cells = <2>;
#size-cells = <1>;
ranges = <1 0 50000000 00010000
ranges = <0 0 ff000000 01000000
1 0 50000000 00010000
2 0 50010000 00010000
3 0 50020000 00010000>;
......@@ -271,31 +294,15 @@ pro_module_dio@3,800 {
compatible = "promess,pro_module_dio";
reg = <3 800 2>;
};
};
pci@f0000d00 {
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
reg = <f0000d00 100>;
interrupt-map-mask = <f800 0 0 7>;
interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
c000 0 0 2 &mpc5200_pic 1 1 3
c000 0 0 3 &mpc5200_pic 1 2 3
c000 0 0 4 &mpc5200_pic 1 3 3
c800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
c800 0 0 2 &mpc5200_pic 1 2 3
c800 0 0 3 &mpc5200_pic 1 3 3
c800 0 0 4 &mpc5200_pic 0 0 3>;
clock-frequency = <0>; // From boot loader
interrupts = <2 8 0 2 9 0 2 a 0>;
interrupt-parent = <&mpc5200_pic>;
bus-range = <0 0>;
ranges = <42000000 0 80000000 80000000 0 20000000
02000000 0 a0000000 a0000000 0 10000000
01000000 0 00000000 b0000000 0 01000000>;
// 16-bit flash device at LocalPlus Bus CS0
flash@0,0 {
compatible = "cfi-flash";
reg = <0 0 01000000>;
bank-width = <2>;
device-width = <2>;
#size-cells = <1>;
#address-cells = <1>;
};
};
};
......@@ -127,10 +127,25 @@ serial@2400 { // PSC3
ethernet@3000 {
device_type = "network";
compatible = "fsl,mpc5200-fec";
reg = <3000 800>;
reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
phy-handle = <&phy0>;
};
mdio@3000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
reg = <3000 400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
interrupt-parent = <&mpc5200_pic>;
phy0: ethernet-phy@0 {
device_type = "ethernet-phy";
reg = <0>;
};
};
ata@3a00 {
......@@ -141,11 +156,19 @@ ata@3a00 {
};
i2c@3d40 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
rtc@68 {
device_type = "rtc";
compatible = "dallas,ds1307";
reg = <68>;
};
};
sram@8000 {
......@@ -154,6 +177,23 @@ sram@8000 {
};
};
lpb {
model = "fsl,lpb";
compatible = "fsl,lpb";
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 fc000000 02000000>;
flash@0,0 {
compatible = "cfi-flash";
reg = <0 0 02000000>;
bank-width = <4>;
device-width = <2>;
#size-cells = <1>;
#address-cells = <1>;
};
};
pci@f0000d00 {
#interrupt-cells = <1>;
#size-cells = <2>;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment