iio: adc: exynos_adc: Add support for s3c24xx ADC

This patch add support for s3c2410/s3c2416/s3c2440/s3c2443 ADC. The s3c24xx
is alomost same as ADCv1. But, There are a little difference as following:
- ADCMUX register address
- ADCDAT mask (10 bit or 12 bit ADC resolution according to SoC version)
- s3c24xx/s3c64xx has not included ADC_PHY enable register
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt

@@ -11,15 +11,25 @@ New driver handles the following
 
 Required properties:
 - compatible:		Must be "samsung,exynos-adc-v1"
-				for exynos4412/5250 controllers.
+				for exynos4412/5250 and s5pv210 controllers.
 			Must be "samsung,exynos-adc-v2" for
 				future controllers.
 			Must be "samsung,exynos3250-adc" for
 				controllers compatible with ADC of Exynos3250.
+			Must be "samsung,s3c2410-adc" for
+				the ADC in s3c2410 and compatibles
+			Must be "samsung,s3c2416-adc" for
+				the ADC in s3c2416 and compatibles
+			Must be "samsung,s3c2440-adc" for
+				the ADC in s3c2440 and compatibles
+			Must be "samsung,s3c2443-adc" for
+				the ADC in s3c2443 and compatibles
 			Must be "samsung,s3c6410-adc" for
 				the ADC in s3c6410 and compatibles
-- reg:			Contains ADC register address range (base address and
-			length) and the address of the phy enable register.
+- reg:			List of ADC register address range
+			- The base address and range of ADC register
+			- The base address and range of ADC_PHY register (every
+			  SoC except for s3c24xx/s3c64xx ADC)
 - interrupts: 		Contains the interrupt information for the timer. The
 			format is being dependent on which interrupt controller
 			the Samsung device uses.

drivers/iio/adc/Kconfig

@@ -129,7 +129,7 @@ config AT91_ADC
 
 config EXYNOS_ADC
 	tristate "Exynos ADC driver support"
-	depends on ARCH_EXYNOS || (OF && COMPILE_TEST)
+	depends on ARCH_EXYNOS || ARCH_S3C24XX || ARCH_S3C64XX || (OF && COMPILE_TEST)
 	help
 	  Core support for the ADC block found in the Samsung EXYNOS series
 	  of SoCs for drivers such as the touchscreen and hwmon to use to share

drivers/iio/adc/exynos_adc.c

@@ -47,6 +47,9 @@
 #define ADC_V1_INTCLR(x)	((x) + 0x18)
 #define ADC_V1_MUX(x)		((x) + 0x1c)
 
+/* S3C2410 ADC registers definitions */
+#define ADC_S3C2410_MUX(x)	((x) + 0x18)
+
 /* Future ADC_V2 registers definitions */
 #define ADC_V2_CON1(x)		((x) + 0x00)
 #define ADC_V2_CON2(x)		((x) + 0x04)
@@ -63,6 +66,8 @@
 
 /* Bit definitions for S3C2410 ADC */
 #define ADC_S3C2410_CON_SELMUX(x) (((x) & 7) << 3)
+#define ADC_S3C2410_DATX_MASK	0x3FF
+#define ADC_S3C2416_CON_RES_SEL	(1u << 3)
 
 /* Bit definitions for ADC_V2 */
 #define ADC_V2_CON1_SOFT_RESET	(1u << 2)
@@ -80,6 +85,7 @@
 
 /* Bit definitions common for ADC_V1 and ADC_V2 */
 #define ADC_CON_EN_START	(1u << 0)
+#define ADC_CON_EN_START_MASK	(0x3 << 0)
 #define ADC_DATX_MASK		0xFFF
 
 #define EXYNOS_ADC_TIMEOUT	(msecs_to_jiffies(100))
@@ -103,6 +109,8 @@ struct exynos_adc {
 struct exynos_adc_data {
 	int num_channels;
 	bool needs_sclk;
+	bool needs_adc_phy;
+	u32 mask;
 
 	void (*init_hw)(struct exynos_adc *info);
 	void (*exit_hw)(struct exynos_adc *info);
@@ -174,6 +182,7 @@ static void exynos_adc_v1_init_hw(struct exynos_adc *info)
 {
 	u32 con1;
 
+	if (info->data->needs_adc_phy)
 		writel(1, info->enable_reg);
 
 	/* set default prescaler values and Enable prescaler */
@@ -188,6 +197,7 @@ static void exynos_adc_v1_exit_hw(struct exynos_adc *info)
 {
 	u32 con;
 
+	if (info->data->needs_adc_phy)
 		writel(0, info->enable_reg);
 
 	con = readl(ADC_V1_CON(info->regs));
@@ -213,6 +223,8 @@ static void exynos_adc_v1_start_conv(struct exynos_adc *info,
 
 static const struct exynos_adc_data exynos_adc_v1_data = {
 	.num_channels	= MAX_ADC_V1_CHANNELS,
+	.mask		= ADC_DATX_MASK,	/* 12 bit ADC resolution */
+	.needs_adc_phy	= true,
 
 	.init_hw	= exynos_adc_v1_init_hw,
 	.exit_hw	= exynos_adc_v1_exit_hw,
@@ -220,6 +232,53 @@ static const struct exynos_adc_data exynos_adc_v1_data = {
 	.start_conv	= exynos_adc_v1_start_conv,
 };
 
+static void exynos_adc_s3c2416_start_conv(struct exynos_adc *info,
+					  unsigned long addr)
+{
+	u32 con1;
+
+	/* Enable 12 bit ADC resolution */
+	con1 = readl(ADC_V1_CON(info->regs));
+	con1 |= ADC_S3C2416_CON_RES_SEL;
+	writel(con1, ADC_V1_CON(info->regs));
+
+	/* Select channel for S3C2416 */
+	writel(addr, ADC_S3C2410_MUX(info->regs));
+
+	con1 = readl(ADC_V1_CON(info->regs));
+	writel(con1 | ADC_CON_EN_START, ADC_V1_CON(info->regs));
+}
+
+static struct exynos_adc_data const exynos_adc_s3c2416_data = {
+	.num_channels	= MAX_ADC_V1_CHANNELS,
+	.mask		= ADC_DATX_MASK,	/* 12 bit ADC resolution */
+
+	.init_hw	= exynos_adc_v1_init_hw,
+	.exit_hw	= exynos_adc_v1_exit_hw,
+	.start_conv	= exynos_adc_s3c2416_start_conv,
+};
+
+static void exynos_adc_s3c2443_start_conv(struct exynos_adc *info,
+					  unsigned long addr)
+{
+	u32 con1;
+
+	/* Select channel for S3C2433 */
+	writel(addr, ADC_S3C2410_MUX(info->regs));
+
+	con1 = readl(ADC_V1_CON(info->regs));
+	writel(con1 | ADC_CON_EN_START, ADC_V1_CON(info->regs));
+}
+
+static struct exynos_adc_data const exynos_adc_s3c2443_data = {
+	.num_channels	= MAX_ADC_V1_CHANNELS,
+	.mask		= ADC_S3C2410_DATX_MASK, /* 10 bit ADC resolution */
+
+	.init_hw	= exynos_adc_v1_init_hw,
+	.exit_hw	= exynos_adc_v1_exit_hw,
+	.start_conv	= exynos_adc_s3c2443_start_conv,
+};
+
 static void exynos_adc_s3c64xx_start_conv(struct exynos_adc *info,
 					  unsigned long addr)
 {
@@ -231,8 +290,18 @@ static void exynos_adc_s3c64xx_start_conv(struct exynos_adc *info,
 	writel(con1 | ADC_CON_EN_START, ADC_V1_CON(info->regs));
 }
 
+static struct exynos_adc_data const exynos_adc_s3c24xx_data = {
+	.num_channels	= MAX_ADC_V1_CHANNELS,
+	.mask		= ADC_S3C2410_DATX_MASK, /* 10 bit ADC resolution */
+
+	.init_hw	= exynos_adc_v1_init_hw,
+	.exit_hw	= exynos_adc_v1_exit_hw,
+	.start_conv	= exynos_adc_s3c64xx_start_conv,
+};
+
 static struct exynos_adc_data const exynos_adc_s3c64xx_data = {
 	.num_channels	= MAX_ADC_V1_CHANNELS,
+	.mask		= ADC_DATX_MASK,	/* 12 bit ADC resolution */
 
 	.init_hw	= exynos_adc_v1_init_hw,
 	.exit_hw	= exynos_adc_v1_exit_hw,
@@ -244,6 +313,7 @@ static void exynos_adc_v2_init_hw(struct exynos_adc *info)
 {
 	u32 con1, con2;
 
+	if (info->data->needs_adc_phy)
 		writel(1, info->enable_reg);
 
 	con1 = ADC_V2_CON1_SOFT_RESET;
@@ -261,6 +331,7 @@ static void exynos_adc_v2_exit_hw(struct exynos_adc *info)
 {
 	u32 con;
 
+	if (info->data->needs_adc_phy)
 		writel(0, info->enable_reg);
 
 	con = readl(ADC_V2_CON1(info->regs));
@@ -289,6 +360,8 @@ static void exynos_adc_v2_start_conv(struct exynos_adc *info,
 
 static const struct exynos_adc_data exynos_adc_v2_data = {
 	.num_channels	= MAX_ADC_V2_CHANNELS,
+	.mask		= ADC_DATX_MASK, /* 12 bit ADC resolution */
+	.needs_adc_phy	= true,
 
 	.init_hw	= exynos_adc_v2_init_hw,
 	.exit_hw	= exynos_adc_v2_exit_hw,
@@ -298,7 +371,9 @@ static const struct exynos_adc_data exynos_adc_v2_data = {
 
 static const struct exynos_adc_data exynos3250_adc_data = {
 	.num_channels	= MAX_EXYNOS3250_ADC_CHANNELS,
+	.mask		= ADC_DATX_MASK, /* 12 bit ADC resolution */
 	.needs_sclk	= true,
+	.needs_adc_phy	= true,
 
 	.init_hw	= exynos_adc_v2_init_hw,
 	.exit_hw	= exynos_adc_v2_exit_hw,
@@ -308,6 +383,18 @@ static const struct exynos_adc_data exynos3250_adc_data = {
 
 static const struct of_device_id exynos_adc_match[] = {
 	{
+		.compatible = "samsung,s3c2410-adc",
+		.data = &exynos_adc_s3c24xx_data,
+	}, {
+		.compatible = "samsung,s3c2416-adc",
+		.data = &exynos_adc_s3c2416_data,
+	}, {
+		.compatible = "samsung,s3c2440-adc",
+		.data = &exynos_adc_s3c24xx_data,
+	}, {
+		.compatible = "samsung,s3c2443-adc",
+		.data = &exynos_adc_s3c2443_data,
+	}, {
 		.compatible = "samsung,s3c6410-adc",
 		.data = &exynos_adc_s3c64xx_data,
 	}, {
@@ -373,9 +460,10 @@ static int exynos_read_raw(struct iio_dev *indio_dev,
 static irqreturn_t exynos_adc_isr(int irq, void *dev_id)
 {
 	struct exynos_adc *info = (struct exynos_adc *)dev_id;
+	u32 mask = info->data->mask;
 
 	/* Read value */
-	info->value = readl(ADC_V1_DATX(info->regs)) & ADC_DATX_MASK;
+	info->value = readl(ADC_V1_DATX(info->regs)) & mask;
 
 	/* clear irq */
 	if (info->data->clear_irq)
@@ -468,10 +556,13 @@ static int exynos_adc_probe(struct platform_device *pdev)
 	if (IS_ERR(info->regs))
 		return PTR_ERR(info->regs);
 
+
+	if (info->data->needs_adc_phy) {
 		mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 		info->enable_reg = devm_ioremap_resource(&pdev->dev, mem);
 		if (IS_ERR(info->enable_reg))
 			return PTR_ERR(info->enable_reg);
+	}
 
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0) {