Merge tag 'nand/for-4.15' of git://git.infradead.org/l2-mtd

From Boris:
"
Core changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
  page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()

Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
  time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
"

Documentation/devicetree/bindings/mtd/denali-nand.txt

@@ -29,7 +29,7 @@ nand: nand@ff900000 {
 	#address-cells = <1>;
 	#size-cells = <1>;
 	compatible = "altr,socfpga-denali-nand";
-	reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;
+	reg = <0xff900000 0x20>, <0xffb80000 0x1000>;
 	reg-names = "nand_data", "denali_reg";
 	interrupts = <0 144 4>;
 };

Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt

@@ -5,9 +5,13 @@ Required properties:
  - compatible:		Should be set to one of the following:
 			marvell,pxa3xx-nand
 			marvell,armada370-nand
+			marvell,armada-8k-nand
  - reg: 		The register base for the controller
  - interrupts:		The interrupt to map
  - #address-cells:	Set to <1> if the node includes partitions
+ - marvell,system-controller: Set to retrieve the syscon node that handles
+			NAND controller related registers (only required
+			with marvell,armada-8k-nand compatible).
 
 Optional properties:
 

arch/arm/mach-pxa/cm-x255.c

@@ -14,7 +14,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/nand-gpio.h>
-
+#include <linux/gpio/machine.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/pxa2xx_spi.h>
 
@@ -176,6 +176,17 @@ static inline void cmx255_init_nor(void) {}
 #endif
 
 #if defined(CONFIG_MTD_NAND_GPIO) || defined(CONFIG_MTD_NAND_GPIO_MODULE)
+
+static struct gpiod_lookup_table cmx255_nand_gpiod_table = {
+	.dev_id         = "gpio-nand",
+	.table          = {
+		GPIO_LOOKUP("gpio-pxa", GPIO_NAND_CS, "nce", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", GPIO_NAND_CLE, "cle", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", GPIO_NAND_ALE, "ale", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", GPIO_NAND_RB, "rdy", GPIO_ACTIVE_HIGH),
+	},
+};
+
 static struct resource cmx255_nand_resource[] = {
 	[0] = {
 		.start = PXA_CS1_PHYS,
@@ -198,11 +209,6 @@ static struct mtd_partition cmx255_nand_parts[] = {
 };
 
 static struct gpio_nand_platdata cmx255_nand_platdata = {
-	.gpio_nce = GPIO_NAND_CS,
-	.gpio_cle = GPIO_NAND_CLE,
-	.gpio_ale = GPIO_NAND_ALE,
-	.gpio_rdy = GPIO_NAND_RB,
-	.gpio_nwp = -1,
 	.parts = cmx255_nand_parts,
 	.num_parts = ARRAY_SIZE(cmx255_nand_parts),
 	.chip_delay = 25,
@@ -220,6 +226,7 @@ static struct platform_device cmx255_nand = {
 
 static void __init cmx255_init_nand(void)
 {
+	gpiod_add_lookup_table(&cmx255_nand_gpiod_table);
 	platform_device_register(&cmx255_nand);
 }
 #else

drivers/mtd/nand/Kconfig

@@ -317,8 +317,11 @@ config MTD_NAND_PXA3xx
 	tristate "NAND support on PXA3xx and Armada 370/XP"
 	depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU
 	help
+
 	  This enables the driver for the NAND flash device found on
-	  PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
+	  PXA3xx processors (NFCv1) and also on 32-bit Armada
+	  platforms (XP, 370, 375, 38x, 39x) and 64-bit Armada
+	  platforms (7K, 8K) (NFCv2).
 
 config MTD_NAND_SLC_LPC32XX
 	tristate "NXP LPC32xx SLC Controller"

drivers/mtd/nand/Makefile

@@ -58,7 +58,7 @@ obj-$(CONFIG_MTD_NAND_SUNXI)		+= sunxi_nand.o
 obj-$(CONFIG_MTD_NAND_HISI504)	        += hisi504_nand.o
 obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
 obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
-obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_nand.o mtk_ecc.o
+obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
 
 nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
 nand-objs += nand_amd.o

drivers/mtd/nand/atmel/nand-controller.c

@@ -718,8 +718,7 @@ static void atmel_nfc_set_op_addr(struct nand_chip *chip, int page, int column)
 		nc->op.addrs[nc->op.naddrs++] = page;
 		nc->op.addrs[nc->op.naddrs++] = page >> 8;
 
-		if ((mtd->writesize > 512 && chip->chipsize > SZ_128M) ||
-		    (mtd->writesize <= 512 && chip->chipsize > SZ_32M))
+		if (chip->options & NAND_ROW_ADDR_3)
 			nc->op.addrs[nc->op.naddrs++] = page >> 16;
 	}
 }
@@ -2530,6 +2529,9 @@ static __maybe_unused int atmel_nand_controller_resume(struct device *dev)
 	struct atmel_nand_controller *nc = dev_get_drvdata(dev);
 	struct atmel_nand *nand;
 
+	if (nc->pmecc)
+		atmel_pmecc_reset(nc->pmecc);
+
 	list_for_each_entry(nand, &nc->chips, node) {
 		int i;
 
@@ -2547,6 +2549,7 @@ static struct platform_driver atmel_nand_controller_driver = {
 	.driver = {
 		.name = "atmel-nand-controller",
 		.of_match_table = of_match_ptr(atmel_nand_controller_of_ids),
+		.pm = &atmel_nand_controller_pm_ops,
 	},
 	.probe = atmel_nand_controller_probe,
 	.remove = atmel_nand_controller_remove,

drivers/mtd/nand/atmel/pmecc.c

@@ -765,6 +765,13 @@ void atmel_pmecc_get_generated_eccbytes(struct atmel_pmecc_user *user,
 }
 EXPORT_SYMBOL_GPL(atmel_pmecc_get_generated_eccbytes);
 
+void atmel_pmecc_reset(struct atmel_pmecc *pmecc)
+{
+	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+}
+EXPORT_SYMBOL_GPL(atmel_pmecc_reset);
+
 int atmel_pmecc_enable(struct atmel_pmecc_user *user, int op)
 {
 	struct atmel_pmecc *pmecc = user->pmecc;
@@ -797,10 +804,7 @@ EXPORT_SYMBOL_GPL(atmel_pmecc_enable);
 
 void atmel_pmecc_disable(struct atmel_pmecc_user *user)
 {
-	struct atmel_pmecc *pmecc = user->pmecc;
-
-	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
-	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	atmel_pmecc_reset(user->pmecc);
 	mutex_unlock(&user->pmecc->lock);
 }
 EXPORT_SYMBOL_GPL(atmel_pmecc_disable);
@@ -855,10 +859,7 @@ static struct atmel_pmecc *atmel_pmecc_create(struct platform_device *pdev,
 
 	/* Disable all interrupts before registering the PMECC handler. */
 	writel(0xffffffff, pmecc->regs.base + ATMEL_PMECC_IDR);
-
-	/* Reset the ECC engine */
-	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
-	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	atmel_pmecc_reset(pmecc);
 
 	return pmecc;
 }

drivers/mtd/nand/atmel/pmecc.h

@@ -61,6 +61,7 @@ atmel_pmecc_create_user(struct atmel_pmecc *pmecc,
 			struct atmel_pmecc_user_req *req);
 void atmel_pmecc_destroy_user(struct atmel_pmecc_user *user);
 
+void atmel_pmecc_reset(struct atmel_pmecc *pmecc);
 int atmel_pmecc_enable(struct atmel_pmecc_user *user, int op);
 void atmel_pmecc_disable(struct atmel_pmecc_user *user);
 int atmel_pmecc_wait_rdy(struct atmel_pmecc_user *user);

drivers/mtd/nand/au1550nd.c

@@ -331,8 +331,7 @@ static void au1550_command(struct mtd_info *mtd, unsigned command, int column, i
 
 			ctx->write_byte(mtd, (u8)(page_addr >> 8));
 
-			/* One more address cycle for devices > 32MiB */
-			if (this->chipsize > (32 << 20))
+			if (this->options & NAND_ROW_ADDR_3)
 				ctx->write_byte(mtd,
 						((page_addr >> 16) & 0x0f));
 		}

drivers/mtd/nand/denali.c

@@ -10,20 +10,18 @@
  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
- *
  */
-#include <linux/interrupt.h>
-#include <linux/delay.h>
+
+#include <linux/bitfield.h>
+#include <linux/completion.h>
 #include <linux/dma-mapping.h>
-#include <linux/wait.h>
-#include <linux/mutex.h>
-#include <linux/mtd/mtd.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
 #include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/rawnand.h>
 #include <linux/slab.h>
+#include <linux/spinlock.h>
 
 #include "denali.h"
 
@@ -31,9 +29,9 @@ MODULE_LICENSE("GPL");
 
 #define DENALI_NAND_NAME    "denali-nand"
 
-/* Host Data/Command Interface */
-#define DENALI_HOST_ADDR	0x00
-#define DENALI_HOST_DATA	0x10
+/* for Indexed Addressing */
+#define DENALI_INDEXED_CTRL	0x00
+#define DENALI_INDEXED_DATA	0x10
 
 #define DENALI_MAP00		(0 << 26)	/* direct access to buffer */
 #define DENALI_MAP01		(1 << 26)	/* read/write pages in PIO */
@@ -61,31 +59,55 @@ MODULE_LICENSE("GPL");
  */
 #define DENALI_CLK_X_MULT	6
 
-/*
- * this macro allows us to convert from an MTD structure to our own
- * device context (denali) structure.
- */
 static inline struct denali_nand_info *mtd_to_denali(struct mtd_info *mtd)
 {
 	return container_of(mtd_to_nand(mtd), struct denali_nand_info, nand);
 }
 
-static void denali_host_write(struct denali_nand_info *denali,
-			      uint32_t addr, uint32_t data)
+/*
+ * Direct Addressing - the slave address forms the control information (command
+ * type, bank, block, and page address).  The slave data is the actual data to
+ * be transferred.  This mode requires 28 bits of address region allocated.
+ */
+static u32 denali_direct_read(struct denali_nand_info *denali, u32 addr)
+{
+	return ioread32(denali->host + addr);
+}
+
+static void denali_direct_write(struct denali_nand_info *denali, u32 addr,
+				u32 data)
 {
-	iowrite32(addr, denali->host + DENALI_HOST_ADDR);
-	iowrite32(data, denali->host + DENALI_HOST_DATA);
+	iowrite32(data, denali->host + addr);
+}
+
+/*
+ * Indexed Addressing - address translation module intervenes in passing the
+ * control information.  This mode reduces the required address range.  The
+ * control information and transferred data are latched by the registers in
+ * the translation module.
+ */
+static u32 denali_indexed_read(struct denali_nand_info *denali, u32 addr)
+{
+	iowrite32(addr, denali->host + DENALI_INDEXED_CTRL);
+	return ioread32(denali->host + DENALI_INDEXED_DATA);
+}
+
+static void denali_indexed_write(struct denali_nand_info *denali, u32 addr,
+				 u32 data)
+{
+	iowrite32(addr, denali->host + DENALI_INDEXED_CTRL);
+	iowrite32(data, denali->host + DENALI_INDEXED_DATA);
 }
 
 /*
  * Use the configuration feature register to determine the maximum number of
  * banks that the hardware supports.
  */
-static void detect_max_banks(struct denali_nand_info *denali)
+static void denali_detect_max_banks(struct denali_nand_info *denali)
 {
 	uint32_t features = ioread32(denali->reg + FEATURES);
 
-	denali->max_banks = 1 << (features & FEATURES__N_BANKS);
+	denali->max_banks = 1 << FIELD_GET(FEATURES__N_BANKS, features);
 
 	/* the encoding changed from rev 5.0 to 5.1 */
 	if (denali->revision < 0x0501)
@@ -189,7 +211,7 @@ static uint32_t denali_wait_for_irq(struct denali_nand_info *denali,
 						msecs_to_jiffies(1000));
 	if (!time_left) {
 		dev_err(denali->dev, "timeout while waiting for irq 0x%x\n",
-			denali->irq_mask);
+			irq_mask);
 		return 0;
 	}
 
@@ -208,73 +230,47 @@ static uint32_t denali_check_irq(struct denali_nand_info *denali)
 	return irq_status;
 }
 
-/*
- * This helper function setups the registers for ECC and whether or not
- * the spare area will be transferred.
- */
-static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en,
-				bool transfer_spare)
-{
-	int ecc_en_flag, transfer_spare_flag;
-
-	/* set ECC, transfer spare bits if needed */
-	ecc_en_flag = ecc_en ? ECC_ENABLE__FLAG : 0;
-	transfer_spare_flag = transfer_spare ? TRANSFER_SPARE_REG__FLAG : 0;
-
-	/* Enable spare area/ECC per user's request. */
-	iowrite32(ecc_en_flag, denali->reg + ECC_ENABLE);
-	iowrite32(transfer_spare_flag, denali->reg + TRANSFER_SPARE_REG);
-}
-
 static void denali_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 {
 	struct denali_nand_info *denali = mtd_to_denali(mtd);
+	u32 addr = DENALI_MAP11_DATA | DENALI_BANK(denali);
 	int i;
 
-	iowrite32(DENALI_MAP11_DATA | DENALI_BANK(denali),
-		  denali->host + DENALI_HOST_ADDR);
-
 	for (i = 0; i < len; i++)
-		buf[i] = ioread32(denali->host + DENALI_HOST_DATA);
+		buf[i] = denali->host_read(denali, addr);
 }
 
 static void denali_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
 {
 	struct denali_nand_info *denali = mtd_to_denali(mtd);
+	u32 addr = DENALI_MAP11_DATA | DENALI_BANK(denali);
 	int i;
 
-	iowrite32(DENALI_MAP11_DATA | DENALI_BANK(denali),
-		  denali->host + DENALI_HOST_ADDR);
-
 	for (i = 0; i < len; i++)
-		iowrite32(buf[i], denali->host + DENALI_HOST_DATA);
+		denali->host_write(denali, addr, buf[i]);
 }
 
 static void denali_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
 {
 	struct denali_nand_info *denali = mtd_to_denali(mtd);
+	u32 addr = DENALI_MAP11_DATA | DENALI_BANK(denali);
 	uint16_t *buf16 = (uint16_t *)buf;
 	int i;
 
-	iowrite32(DENALI_MAP11_DATA | DENALI_BANK(denali),
-		  denali->host + DENALI_HOST_ADDR);
-
 	for (i = 0; i < len / 2; i++)
-		buf16[i] = ioread32(denali->host + DENALI_HOST_DATA);
+		buf16[i] = denali->host_read(denali, addr);
 }
 
 static void denali_write_buf16(struct mtd_info *mtd, const uint8_t *buf,
 			       int len)
 {
 	struct denali_nand_info *denali = mtd_to_denali(mtd);
+	u32 addr = DENALI_MAP11_DATA | DENALI_BANK(denali);
 	const uint16_t *buf16 = (const uint16_t *)buf;
 	int i;
 
-	iowrite32(DENALI_MAP11_DATA | DENALI_BANK(denali),
-		  denali->host + DENALI_HOST_ADDR);
-
 	for (i = 0; i < len / 2; i++)
-		iowrite32(buf16[i], denali->host + DENALI_HOST_DATA);
+		denali->host_write(denali, addr, buf16[i]);
 }
 
 static uint8_t denali_read_byte(struct mtd_info *mtd)
@@ -319,7 +315,7 @@ static void denali_cmd_ctrl(struct mtd_info *mtd, int dat, unsigned int ctrl)
 	if (ctrl & NAND_CTRL_CHANGE)
 		denali_reset_irq(denali);
 
-	denali_host_write(denali, DENALI_BANK(denali) | type, dat);
+	denali->host_write(denali, DENALI_BANK(denali) | type, dat);
 }
 
 static int denali_dev_ready(struct mtd_info *mtd)
@@ -389,7 +385,7 @@ static int denali_hw_ecc_fixup(struct mtd_info *mtd,
 		return 0;
 	}
 
-	max_bitflips = ecc_cor & ECC_COR_INFO__MAX_ERRORS;
+	max_bitflips = FIELD_GET(ECC_COR_INFO__MAX_ERRORS, ecc_cor);
 
 	/*
 	 * The register holds the maximum of per-sector corrected bitflips.
@@ -402,13 +398,6 @@ static int denali_hw_ecc_fixup(struct mtd_info *mtd,
 	return max_bitflips;
 }
 
-#define ECC_SECTOR(x)	(((x) & ECC_ERROR_ADDRESS__SECTOR_NR) >> 12)
-#define ECC_BYTE(x)	(((x) & ECC_ERROR_ADDRESS__OFFSET))
-#define ECC_CORRECTION_VALUE(x) ((x) & ERR_CORRECTION_INFO__BYTEMASK)
-#define ECC_ERROR_UNCORRECTABLE(x) ((x) & ERR_CORRECTION_INFO__ERROR_TYPE)
-#define ECC_ERR_DEVICE(x)	(((x) & ERR_CORRECTION_INFO__DEVICE_NR) >> 8)
-#define ECC_LAST_ERR(x)		((x) & ERR_CORRECTION_INFO__LAST_ERR_INFO)
-
 static int denali_sw_ecc_fixup(struct mtd_info *mtd,
 			       struct denali_nand_info *denali,
 			       unsigned long *uncor_ecc_flags, uint8_t *buf)
@@ -426,18 +415,20 @@ static int denali_sw_ecc_fixup(struct mtd_info *mtd,
 
 	do {
 		err_addr = ioread32(denali->reg + ECC_ERROR_ADDRESS);
-		err_sector = ECC_SECTOR(err_addr);
-		err_byte = ECC_BYTE(err_addr);
+		err_sector = FIELD_GET(ECC_ERROR_ADDRESS__SECTOR, err_addr);
+		err_byte = FIELD_GET(ECC_ERROR_ADDRESS__OFFSET, err_addr);
 
 		err_cor_info = ioread32(denali->reg + ERR_CORRECTION_INFO);
-		err_cor_value = ECC_CORRECTION_VALUE(err_cor_info);
-		err_device = ECC_ERR_DEVICE(err_cor_info);
+		err_cor_value = FIELD_GET(ERR_CORRECTION_INFO__BYTE,
+					  err_cor_info);
+		err_device = FIELD_GET(ERR_CORRECTION_INFO__DEVICE,
+				       err_cor_info);
 
 		/* reset the bitflip counter when crossing ECC sector */
 		if (err_sector != prev_sector)
 			bitflips = 0;
 
-		if (ECC_ERROR_UNCORRECTABLE(err_cor_info)) {
+		if (err_cor_info & ERR_CORRECTION_INFO__UNCOR) {
 			/*
 			 * Check later if this is a real ECC error, or
 			 * an erased sector.
@@ -467,12 +458,11 @@ static int denali_sw_ecc_fixup(struct mtd_info *mtd,
 		}
 
 		prev_sector = err_sector;
-	} while (!ECC_LAST_ERR(err_cor_info));
+	} while (!(err_cor_info & ERR_CORRECTION_INFO__LAST_ERR));
 
 	/*
-	 * Once handle all ecc errors, controller will trigger a
-	 * ECC_TRANSACTION_DONE interrupt, so here just wait for
-	 * a while for this interrupt
+	 * Once handle all ECC errors, controller will trigger an
+	 * ECC_TRANSACTION_DONE interrupt.
 	 */
 	irq_status = denali_wait_for_irq(denali, INTR__ECC_TRANSACTION_DONE);
 	if (!(irq_status & INTR__ECC_TRANSACTION_DONE))
@@ -481,13 +471,6 @@ static int denali_sw_ecc_fixup(struct mtd_info *mtd,
 	return max_bitflips;
 }
 
-/* programs the controller to either enable/disable DMA transfers */
-static void denali_enable_dma(struct denali_nand_info *denali, bool en)
-{
-	iowrite32(en ? DMA_ENABLE__FLAG : 0, denali->reg + DMA_ENABLE);
-	ioread32(denali->reg + DMA_ENABLE);
-}
-
 static void denali_setup_dma64(struct denali_nand_info *denali,
 			       dma_addr_t dma_addr, int page, int write)
 {
@@ -502,14 +485,14 @@ static void denali_setup_dma64(struct denali_nand_info *denali,
 	 * 1. setup transfer type, interrupt when complete,
 	 *    burst len = 64 bytes, the number of pages
 	 */
-	denali_host_write(denali, mode,
-			  0x01002000 | (64 << 16) | (write << 8) | page_count);
+	denali->host_write(denali, mode,
+			   0x01002000 | (64 << 16) | (write << 8) | page_count);
 
 	/* 2. set memory low address */
-	denali_host_write(denali, mode, dma_addr);
+	denali->host_write(denali, mode, lower_32_bits(dma_addr));
 
 	/* 3. set memory high address */
-	denali_host_write(denali, mode, (uint64_t)dma_addr >> 32);
+	denali->host_write(denali, mode, upper_32_bits(dma_addr));
 }
 
 static void denali_setup_dma32(struct denali_nand_info *denali,
@@ -523,32 +506,23 @@ static void denali_setup_dma32(struct denali_nand_info *denali,
 	/* DMA is a four step process */
 
 	/* 1. setup transfer type and # of pages */
-	denali_host_write(denali, mode | page,
-			  0x2000 | (write << 8) | page_count);
+	denali->host_write(denali, mode | page,
+			   0x2000 | (write << 8) | page_count);
 
 	/* 2. set memory high address bits 23:8 */
-	denali_host_write(denali, mode | ((dma_addr >> 16) << 8), 0x2200);
+	denali->host_write(denali, mode | ((dma_addr >> 16) << 8), 0x2200);
 
 	/* 3. set memory low address bits 23:8 */
-	denali_host_write(denali, mode | ((dma_addr & 0xffff) << 8), 0x2300);
+	denali->host_write(denali, mode | ((dma_addr & 0xffff) << 8), 0x2300);
 
 	/* 4. interrupt when complete, burst len = 64 bytes */
-	denali_host_write(denali, mode | 0x14000, 0x2400);
-}
-
-static void denali_setup_dma(struct denali_nand_info *denali,
-			     dma_addr_t dma_addr, int page, int write)
-{
-	if (denali->caps & DENALI_CAP_DMA_64BIT)
-		denali_setup_dma64(denali, dma_addr, page, write);
-	else
-		denali_setup_dma32(denali, dma_addr, page, write);
+	denali->host_write(denali, mode | 0x14000, 0x2400);
 }
 
 static int denali_pio_read(struct denali_nand_info *denali, void *buf,
 			   size_t size, int page, int raw)
 {
-	uint32_t addr = DENALI_BANK(denali) | page;
+	u32 addr = DENALI_MAP01 | DENALI_BANK(denali) | page;
 	uint32_t *buf32 = (uint32_t *)buf;
 	uint32_t irq_status, ecc_err_mask;
 	int i;
@@ -560,9 +534,8 @@ static int denali_pio_read(struct denali_nand_info *denali, void *buf,
 
 	denali_reset_irq(denali);
 
-	iowrite32(DENALI_MAP01 | addr, denali->host + DENALI_HOST_ADDR);
 	for (i = 0; i < size / 4; i++)
-		*buf32++ = ioread32(denali->host + DENALI_HOST_DATA);
+		*buf32++ = denali->host_read(denali, addr);
 
 	irq_status = denali_wait_for_irq(denali, INTR__PAGE_XFER_INC);
 	if (!(irq_status & INTR__PAGE_XFER_INC))
@@ -577,16 +550,15 @@ static int denali_pio_read(struct denali_nand_info *denali, void *buf,
 static int denali_pio_write(struct denali_nand_info *denali,
 			    const void *buf, size_t size, int page, int raw)
 {
-	uint32_t addr = DENALI_BANK(denali) | page;
+	u32 addr = DENALI_MAP01 | DENALI_BANK(denali) | page;
 	const uint32_t *buf32 = (uint32_t *)buf;
 	uint32_t irq_status;
 	int i;
 
 	denali_reset_irq(denali);
 
-	iowrite32(DENALI_MAP01 | addr, denali->host + DENALI_HOST_ADDR);
 	for (i = 0; i < size / 4; i++)
-		iowrite32(*buf32++, denali->host + DENALI_HOST_DATA);
+		denali->host_write(denali, addr, *buf32++);
 
 	irq_status = denali_wait_for_irq(denali,
 				INTR__PROGRAM_COMP | INTR__PROGRAM_FAIL);
@@ -635,19 +607,19 @@ static int denali_dma_xfer(struct denali_nand_info *denali, void *buf,
 		ecc_err_mask = INTR__ECC_ERR;
 	}
 
-	denali_enable_dma(denali, true);
+	iowrite32(DMA_ENABLE__FLAG, denali->reg + DMA_ENABLE);
 
 	denali_reset_irq(denali);
-	denali_setup_dma(denali, dma_addr, page, write);
+	denali->setup_dma(denali, dma_addr, page, write);
 
-	/* wait for operation to complete */
 	irq_status = denali_wait_for_irq(denali, irq_mask);
 	if (!(irq_status & INTR__DMA_CMD_COMP))
 		ret = -EIO;
 	else if (irq_status & ecc_err_mask)
 		ret = -EBADMSG;
 
-	denali_enable_dma(denali, false);
+	iowrite32(0, denali->reg + DMA_ENABLE);
+
 	dma_unmap_single(denali->dev, dma_addr, size, dir);
 
 	if (irq_status & INTR__ERASED_PAGE)
@@ -659,7 +631,9 @@ static int denali_dma_xfer(struct denali_nand_info *denali, void *buf,
 static int denali_data_xfer(struct denali_nand_info *denali, void *buf,
 			    size_t size, int page, int raw, int write)
 {
-	setup_ecc_for_xfer(denali, !raw, raw);
+	iowrite32(raw ? 0 : ECC_ENABLE__FLAG, denali->reg + ECC_ENABLE);
+	iowrite32(raw ? TRANSFER_SPARE_REG__FLAG : 0,
+		  denali->reg + TRANSFER_SPARE_REG);
 
 	if (denali->dma_avail)
 		return denali_dma_xfer(denali, buf, size, page, raw, write);
@@ -970,8 +944,8 @@ static int denali_erase(struct mtd_info *mtd, int page)
 
 	denali_reset_irq(denali);
 
-	denali_host_write(denali, DENALI_MAP10 | DENALI_BANK(denali) | page,
-			  DENALI_ERASE);
+	denali->host_write(denali, DENALI_MAP10 | DENALI_BANK(denali) | page,
+			   DENALI_ERASE);
 
 	/* wait for erase to complete or failure to occur */
 	irq_status = denali_wait_for_irq(denali,
@@ -1009,7 +983,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
 
 	tmp = ioread32(denali->reg + ACC_CLKS);
 	tmp &= ~ACC_CLKS__VALUE;
-	tmp |= acc_clks;
+	tmp |= FIELD_PREP(ACC_CLKS__VALUE, acc_clks);
 	iowrite32(tmp, denali->reg + ACC_CLKS);
 
 	/* tRWH -> RE_2_WE */
@@ -1018,7 +992,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
 
 	tmp = ioread32(denali->reg + RE_2_WE);
 	tmp &= ~RE_2_WE__VALUE;
-	tmp |= re_2_we;
+	tmp |= FIELD_PREP(RE_2_WE__VALUE, re_2_we);
 	iowrite32(tmp, denali->reg + RE_2_WE);
 
 	/* tRHZ -> RE_2_RE */
@@ -1027,16 +1001,22 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
 
 	tmp = ioread32(denali->reg + RE_2_RE);
 	tmp &= ~RE_2_RE__VALUE;
-	tmp |= re_2_re;
+	tmp |= FIELD_PREP(RE_2_RE__VALUE, re_2_re);
 	iowrite32(tmp, denali->reg + RE_2_RE);
 
-	/* tWHR -> WE_2_RE */
-	we_2_re = DIV_ROUND_UP(timings->tWHR_min, t_clk);
+	/*
+	 * tCCS, tWHR -> WE_2_RE
+	 *
+	 * With WE_2_RE properly set, the Denali controller automatically takes
+	 * care of the delay; the driver need not set NAND_WAIT_TCCS.
+	 */
+	we_2_re = DIV_ROUND_UP(max(timings->tCCS_min, timings->tWHR_min),
+			       t_clk);
 	we_2_re = min_t(int, we_2_re, TWHR2_AND_WE_2_RE__WE_2_RE);
 
 	tmp = ioread32(denali->reg + TWHR2_AND_WE_2_RE);
 	tmp &= ~TWHR2_AND_WE_2_RE__WE_2_RE;
-	tmp |= we_2_re;
+	tmp |= FIELD_PREP(TWHR2_AND_WE_2_RE__WE_2_RE, we_2_re);
 	iowrite32(tmp, denali->reg + TWHR2_AND_WE_2_RE);
 
 	/* tADL -> ADDR_2_DATA */
@@ -1050,8 +1030,8 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
 	addr_2_data = min_t(int, addr_2_data, addr_2_data_mask);
 
 	tmp = ioread32(denali->reg + TCWAW_AND_ADDR_2_DATA);
-	tmp &= ~addr_2_data_mask;
-	tmp |= addr_2_data;
+	tmp &= ~TCWAW_AND_ADDR_2_DATA__ADDR_2_DATA;
+	tmp |= FIELD_PREP(TCWAW_AND_ADDR_2_DATA__ADDR_2_DATA, addr_2_data);
 	iowrite32(tmp, denali->reg + TCWAW_AND_ADDR_2_DATA);
 
 	/* tREH, tWH -> RDWR_EN_HI_CNT */
@@ -1061,7 +1041,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
 
 	tmp = ioread32(denali->reg + RDWR_EN_HI_CNT);
 	tmp &= ~RDWR_EN_HI_CNT__VALUE;
-	tmp |= rdwr_en_hi;
+	tmp |= FIELD_PREP(RDWR_EN_HI_CNT__VALUE, rdwr_en_hi);
 	iowrite32(tmp, denali->reg + RDWR_EN_HI_CNT);
 
 	/* tRP, tWP -> RDWR_EN_LO_CNT */
@@ -1075,7 +1055,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
 
 	tmp = ioread32(denali->reg + RDWR_EN_LO_CNT);
 	tmp &= ~RDWR_EN_LO_CNT__VALUE;
-	tmp |= rdwr_en_lo;
+	tmp |= FIELD_PREP(RDWR_EN_LO_CNT__VALUE, rdwr_en_lo);
 	iowrite32(tmp, denali->reg + RDWR_EN_LO_CNT);
 
 	/* tCS, tCEA -> CS_SETUP_CNT */
@@ -1086,7 +1066,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
 
 	tmp = ioread32(denali->reg + CS_SETUP_CNT);
 	tmp &= ~CS_SETUP_CNT__VALUE;
-	tmp |= cs_setup;
+	tmp |= FIELD_PREP(CS_SETUP_CNT__VALUE, cs_setup);
 	iowrite32(tmp, denali->reg + CS_SETUP_CNT);
 
 	return 0;
@@ -1131,15 +1111,11 @@ static void denali_hw_init(struct denali_nand_info *denali)
 	 * if this value is 0, just let it be.
 	 */
 	denali->oob_skip_bytes = ioread32(denali->reg + SPARE_AREA_SKIP_BYTES);
-	detect_max_banks(denali);
+	denali_detect_max_banks(denali);
 	iowrite32(0x0F, denali->reg + RB_PIN_ENABLED);
 	iowrite32(CHIP_EN_DONT_CARE__FLAG, denali->reg + CHIP_ENABLE_DONT_CARE);
 
 	iowrite32(0xffff, denali->reg + SPARE_AREA_MARKER);
-
-	/* Should set value for these registers when init */
-	iowrite32(0, denali->reg + TWO_ROW_ADDR_CYCLES);
-	iowrite32(1, denali->reg + ECC_ENABLE);
 }
 
 int denali_calc_ecc_bytes(int step_size, int strength)
@@ -1211,22 +1187,6 @@ static const struct mtd_ooblayout_ops denali_ooblayout_ops = {
 	.free = denali_ooblayout_free,
 };
 
-/* initialize driver data structures */
-static void denali_drv_init(struct denali_nand_info *denali)
-{
-	/*
-	 * the completion object will be used to notify
-	 * the callee that the interrupt is done
-	 */
-	init_completion(&denali->complete);
-
-	/*
-	 * the spinlock will be used to synchronize the ISR with any
-	 * element that might be access shared data (interrupt status)
-	 */
-	spin_lock_init(&denali->irq_lock);
-}
-
 static int denali_multidev_fixup(struct denali_nand_info *denali)
 {
 	struct nand_chip *chip = &denali->nand;
@@ -1282,15 +1242,17 @@ int denali_init(struct denali_nand_info *denali)
 {
 	struct nand_chip *chip = &denali->nand;
 	struct mtd_info *mtd = nand_to_mtd(chip);
+	u32 features = ioread32(denali->reg + FEATURES);
 	int ret;
 
 	mtd->dev.parent = denali->dev;
 	denali_hw_init(denali);
-	denali_drv_init(denali);
+
+	init_completion(&denali->complete);
+	spin_lock_init(&denali->irq_lock);
 
 	denali_clear_irq_all(denali);
 
-	/* Request IRQ after all the hardware initialization is finished */
 	ret = devm_request_irq(denali->dev, denali->irq, denali_isr,
 			       IRQF_SHARED, DENALI_NAND_NAME, denali);
 	if (ret) {
@@ -1308,7 +1270,6 @@ int denali_init(struct denali_nand_info *denali)
 	if (!mtd->name)
 		mtd->name = "denali-nand";
 
-	/* register the driver with the NAND core subsystem */
 	chip->select_chip = denali_select_chip;
 	chip->read_byte = denali_read_byte;
 	chip->write_byte = denali_write_byte;
@@ -1317,15 +1278,18 @@ int denali_init(struct denali_nand_info *denali)
 	chip->dev_ready = denali_dev_ready;
 	chip->waitfunc = denali_waitfunc;
 
+	if (features & FEATURES__INDEX_ADDR) {
+		denali->host_read = denali_indexed_read;
+		denali->host_write = denali_indexed_write;
+	} else {
+		denali->host_read = denali_direct_read;
+		denali->host_write = denali_direct_write;
+	}
+
 	/* clk rate info is needed for setup_data_interface */
 	if (denali->clk_x_rate)
 		chip->setup_data_interface = denali_setup_data_interface;
 
-	/*
-	 * scan for NAND devices attached to the controller
-	 * this is the first stage in a two step process to register
-	 * with the nand subsystem
-	 */
 	ret = nand_scan_ident(mtd, denali->max_banks, NULL);
 	if (ret)
 		goto disable_irq;
@@ -1347,20 +1311,15 @@ int denali_init(struct denali_nand_info *denali)
 	if (denali->dma_avail) {
 		chip->options |= NAND_USE_BOUNCE_BUFFER;
 		chip->buf_align = 16;
+		if (denali->caps & DENALI_CAP_DMA_64BIT)
+			denali->setup_dma = denali_setup_dma64;
+		else
+			denali->setup_dma = denali_setup_dma32;
 	}
 
-	/*
-	 * second stage of the NAND scan
-	 * this stage requires information regarding ECC and
-	 * bad block management.
-	 */
-
 	chip->bbt_options |= NAND_BBT_USE_FLASH;
 	chip->bbt_options |= NAND_BBT_NO_OOB;
-
 	chip->ecc.mode = NAND_ECC_HW_SYNDROME;
-
-	/* no subpage writes on denali */
 	chip->options |= NAND_NO_SUBPAGE_WRITE;
 
 	ret = denali_ecc_setup(mtd, chip, denali);
@@ -1373,12 +1332,15 @@ int denali_init(struct denali_nand_info *denali)
 		"chosen ECC settings: step=%d, strength=%d, bytes=%d\n",
 		chip->ecc.size, chip->ecc.strength, chip->ecc.bytes);
 
-	iowrite32(MAKE_ECC_CORRECTION(chip->ecc.strength, 1),
+	iowrite32(FIELD_PREP(ECC_CORRECTION__ERASE_THRESHOLD, 1) |
+		  FIELD_PREP(ECC_CORRECTION__VALUE, chip->ecc.strength),
 		  denali->reg + ECC_CORRECTION);
 	iowrite32(mtd->erasesize / mtd->writesize,
 		  denali->reg + PAGES_PER_BLOCK);
 	iowrite32(chip->options & NAND_BUSWIDTH_16 ? 1 : 0,
 		  denali->reg + DEVICE_WIDTH);
+	iowrite32(chip->options & NAND_ROW_ADDR_3 ? 0 : TWO_ROW_ADDR_CYCLES__FLAG,
+		  denali->reg + TWO_ROW_ADDR_CYCLES);
 	iowrite32(mtd->writesize, denali->reg + DEVICE_MAIN_AREA_SIZE);
 	iowrite32(mtd->oobsize, denali->reg + DEVICE_SPARE_AREA_SIZE);
 
@@ -1441,7 +1403,6 @@ int denali_init(struct denali_nand_info *denali)
 }
 EXPORT_SYMBOL(denali_init);
 
-/* driver exit point */
 void denali_remove(struct denali_nand_info *denali)
 {
 	struct mtd_info *mtd = nand_to_mtd(&denali->nand);

drivers/mtd/nand/denali.h

@@ -10,18 +10,16 @@
  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
- *
  */
 
 #ifndef __DENALI_H__
 #define __DENALI_H__
 
 #include <linux/bitops.h>
+#include <linux/completion.h>
 #include <linux/mtd/rawnand.h>
+#include <linux/spinlock_types.h>
+#include <linux/types.h>
 
 #define DEVICE_RESET				0x0
 #define     DEVICE_RESET__BANK(bank)			BIT(bank)
@@ -111,9 +109,6 @@
 #define ECC_CORRECTION				0x1b0
 #define     ECC_CORRECTION__VALUE			GENMASK(4, 0)
 #define     ECC_CORRECTION__ERASE_THRESHOLD		GENMASK(31, 16)
-#define     MAKE_ECC_CORRECTION(val, thresh)		\
-			(((val) & (ECC_CORRECTION__VALUE)) | \
-			(((thresh) << 16) & (ECC_CORRECTION__ERASE_THRESHOLD)))
 
 #define READ_MODE				0x1c0
 #define     READ_MODE__VALUE				GENMASK(3, 0)
@@ -255,13 +250,13 @@
 
 #define ECC_ERROR_ADDRESS			0x630
 #define     ECC_ERROR_ADDRESS__OFFSET			GENMASK(11, 0)
-#define     ECC_ERROR_ADDRESS__SECTOR_NR		GENMASK(15, 12)
+#define     ECC_ERROR_ADDRESS__SECTOR			GENMASK(15, 12)
 
 #define ERR_CORRECTION_INFO			0x640
-#define     ERR_CORRECTION_INFO__BYTEMASK		GENMASK(7, 0)
-#define     ERR_CORRECTION_INFO__DEVICE_NR		GENMASK(11, 8)
-#define     ERR_CORRECTION_INFO__ERROR_TYPE		BIT(14)
-#define     ERR_CORRECTION_INFO__LAST_ERR_INFO		BIT(15)
+#define     ERR_CORRECTION_INFO__BYTE			GENMASK(7, 0)
+#define     ERR_CORRECTION_INFO__DEVICE			GENMASK(11, 8)
+#define     ERR_CORRECTION_INFO__UNCOR			BIT(14)
+#define     ERR_CORRECTION_INFO__LAST_ERR		BIT(15)
 
 #define ECC_COR_INFO(bank)			(0x650 + (bank) / 2 * 0x10)
 #define     ECC_COR_INFO__SHIFT(bank)			((bank) % 2 * 8)
@@ -310,23 +305,24 @@ struct denali_nand_info {
 	struct device *dev;
 	void __iomem *reg;		/* Register Interface */
 	void __iomem *host;		/* Host Data/Command Interface */
-
-	/* elements used by ISR */
 	struct completion complete;
-	spinlock_t irq_lock;
-	uint32_t irq_mask;
-	uint32_t irq_status;
+	spinlock_t irq_lock;		/* protect irq_mask and irq_status */
+	u32 irq_mask;			/* interrupts we are waiting for */
+	u32 irq_status;			/* interrupts that have happened */
 	int irq;
-
-	void *buf;
+	void *buf;			/* for syndrome layout conversion */
 	dma_addr_t dma_addr;
-	int dma_avail;
+	int dma_avail;			/* can support DMA? */
 	int devs_per_cs;		/* devices connected in parallel */
-	int oob_skip_bytes;
+	int oob_skip_bytes;		/* number of bytes reserved for BBM */
 	int max_banks;
-	unsigned int revision;
-	unsigned int caps;
+	unsigned int revision;		/* IP revision */
+	unsigned int caps;		/* IP capability (or quirk) */
 	const struct nand_ecc_caps *ecc_caps;
+	u32 (*host_read)(struct denali_nand_info *denali, u32 addr);
+	void (*host_write)(struct denali_nand_info *denali, u32 addr, u32 data);
+	void (*setup_dma)(struct denali_nand_info *denali, dma_addr_t dma_addr,
+			  int page, int write);
 };
 
 #define DENALI_CAP_HW_ECC_FIXUP			BIT(0)

drivers/mtd/nand/denali_dt.c

@@ -12,15 +12,16 @@
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
  */
+
 #include <linux/clk.h>
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/ioport.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
-#include <linux/platform_device.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/platform_device.h>
 
 #include "denali.h"
 
@@ -155,7 +156,6 @@ static struct platform_driver denali_dt_driver = {
 		.of_match_table	= denali_nand_dt_ids,
 	},
 };
-
 module_platform_driver(denali_dt_driver);
 
 MODULE_LICENSE("GPL");

drivers/mtd/nand/denali_pci.c

@@ -11,6 +11,9 @@
  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  * more details.
  */
+
+#include <linux/errno.h>
+#include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/pci.h>
@@ -106,7 +109,6 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	return ret;
 }
 
-/* driver exit point */
 static void denali_pci_remove(struct pci_dev *dev)
 {
 	struct denali_nand_info *denali = pci_get_drvdata(dev);
@@ -122,5 +124,4 @@ static struct pci_driver denali_pci_driver = {
 	.probe = denali_pci_probe,
 	.remove = denali_pci_remove,
 };
-
 module_pci_driver(denali_pci_driver);

drivers/mtd/nand/diskonchip.c

@@ -705,8 +705,7 @@ static void doc2001plus_command(struct mtd_info *mtd, unsigned command, int colu
 		if (page_addr != -1) {
 			WriteDOC((unsigned char)(page_addr & 0xff), docptr, Mplus_FlashAddress);
 			WriteDOC((unsigned char)((page_addr >> 8) & 0xff), docptr, Mplus_FlashAddress);
-			/* One more address cycle for higher density devices */
-			if (this->chipsize & 0x0c000000) {
+			if (this->options & NAND_ROW_ADDR_3) {
 				WriteDOC((unsigned char)((page_addr >> 16) & 0x0f), docptr, Mplus_FlashAddress);
 				printk("high density\n");
 			}

drivers/mtd/nand/gpio.c

@@ -23,7 +23,7 @@
 #include <linux/slab.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/io.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/rawnand.h>
@@ -31,12 +31,16 @@
 #include <linux/mtd/nand-gpio.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
-#include <linux/of_gpio.h>
 
 struct gpiomtd {
 	void __iomem		*io_sync;
 	struct nand_chip	nand_chip;
 	struct gpio_nand_platdata plat;
+	struct gpio_desc *nce; /* Optional chip enable */
+	struct gpio_desc *cle;
+	struct gpio_desc *ale;
+	struct gpio_desc *rdy;
+	struct gpio_desc *nwp; /* Optional write protection */
 };
 
 static inline struct gpiomtd *gpio_nand_getpriv(struct mtd_info *mtd)
@@ -78,11 +82,10 @@ static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 	gpio_nand_dosync(gpiomtd);
 
 	if (ctrl & NAND_CTRL_CHANGE) {
-		if (gpio_is_valid(gpiomtd->plat.gpio_nce))
-			gpio_set_value(gpiomtd->plat.gpio_nce,
-				       !(ctrl & NAND_NCE));
-		gpio_set_value(gpiomtd->plat.gpio_cle, !!(ctrl & NAND_CLE));
-		gpio_set_value(gpiomtd->plat.gpio_ale, !!(ctrl & NAND_ALE));
+		if (gpiomtd->nce)
+			gpiod_set_value(gpiomtd->nce, !(ctrl & NAND_NCE));
+		gpiod_set_value(gpiomtd->cle, !!(ctrl & NAND_CLE));
+		gpiod_set_value(gpiomtd->ale, !!(ctrl & NAND_ALE));
 		gpio_nand_dosync(gpiomtd);
 	}
 	if (cmd == NAND_CMD_NONE)
@@ -96,7 +99,7 @@ static int gpio_nand_devready(struct mtd_info *mtd)
 {
 	struct gpiomtd *gpiomtd = gpio_nand_getpriv(mtd);
 
-	return gpio_get_value(gpiomtd->plat.gpio_rdy);
+	return gpiod_get_value(gpiomtd->rdy);
 }
 
 #ifdef CONFIG_OF
@@ -123,12 +126,6 @@ static int gpio_nand_get_config_of(const struct device *dev,
 		}
 	}
 
-	plat->gpio_rdy = of_get_gpio(dev->of_node, 0);
-	plat->gpio_nce = of_get_gpio(dev->of_node, 1);
-	plat->gpio_ale = of_get_gpio(dev->of_node, 2);
-	plat->gpio_cle = of_get_gpio(dev->of_node, 3);
-	plat->gpio_nwp = of_get_gpio(dev->of_node, 4);
-
 	if (!of_property_read_u32(dev->of_node, "chip-delay", &val))
 		plat->chip_delay = val;
 
@@ -201,10 +198,11 @@ static int gpio_nand_remove(struct platform_device *pdev)
 
 	nand_release(nand_to_mtd(&gpiomtd->nand_chip));
 
-	if (gpio_is_valid(gpiomtd->plat.gpio_nwp))
-		gpio_set_value(gpiomtd->plat.gpio_nwp, 0);
-	if (gpio_is_valid(gpiomtd->plat.gpio_nce))
-		gpio_set_value(gpiomtd->plat.gpio_nce, 1);
+	/* Enable write protection and disable the chip */
+	if (gpiomtd->nwp && !IS_ERR(gpiomtd->nwp))
+		gpiod_set_value(gpiomtd->nwp, 0);
+	if (gpiomtd->nce && !IS_ERR(gpiomtd->nce))
+		gpiod_set_value(gpiomtd->nce, 0);
 
 	return 0;
 }
@@ -215,66 +213,66 @@ static int gpio_nand_probe(struct platform_device *pdev)
 	struct nand_chip *chip;
 	struct mtd_info *mtd;
 	struct resource *res;
+	struct device *dev = &pdev->dev;
 	int ret = 0;
 
-	if (!pdev->dev.of_node && !dev_get_platdata(&pdev->dev))
+	if (!dev->of_node && !dev_get_platdata(dev))
 		return -EINVAL;
 
-	gpiomtd = devm_kzalloc(&pdev->dev, sizeof(*gpiomtd), GFP_KERNEL);
+	gpiomtd = devm_kzalloc(dev, sizeof(*gpiomtd), GFP_KERNEL);
 	if (!gpiomtd)
 		return -ENOMEM;
 
 	chip = &gpiomtd->nand_chip;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	chip->IO_ADDR_R = devm_ioremap_resource(&pdev->dev, res);
+	chip->IO_ADDR_R = devm_ioremap_resource(dev, res);
 	if (IS_ERR(chip->IO_ADDR_R))
 		return PTR_ERR(chip->IO_ADDR_R);
 
 	res = gpio_nand_get_io_sync(pdev);
 	if (res) {
-		gpiomtd->io_sync = devm_ioremap_resource(&pdev->dev, res);
+		gpiomtd->io_sync = devm_ioremap_resource(dev, res);
 		if (IS_ERR(gpiomtd->io_sync))
 			return PTR_ERR(gpiomtd->io_sync);
 	}
 
-	ret = gpio_nand_get_config(&pdev->dev, &gpiomtd->plat);
+	ret = gpio_nand_get_config(dev, &gpiomtd->plat);
 	if (ret)
 		return ret;
 
-	if (gpio_is_valid(gpiomtd->plat.gpio_nce)) {
-		ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nce,
-					"NAND NCE");
-		if (ret)
-			return ret;
-		gpio_direction_output(gpiomtd->plat.gpio_nce, 1);
+	/* Just enable the chip */
+	gpiomtd->nce = devm_gpiod_get_optional(dev, "nce", GPIOD_OUT_HIGH);
+	if (IS_ERR(gpiomtd->nce))
+		return PTR_ERR(gpiomtd->nce);
+
+	/* We disable write protection once we know probe() will succeed */
+	gpiomtd->nwp = devm_gpiod_get_optional(dev, "nwp", GPIOD_OUT_LOW);
+	if (IS_ERR(gpiomtd->nwp)) {
+		ret = PTR_ERR(gpiomtd->nwp);
+		goto out_ce;
 	}
 
-	if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) {
-		ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp,
-					"NAND NWP");
-		if (ret)
-			return ret;
+	gpiomtd->nwp = devm_gpiod_get(dev, "ale", GPIOD_OUT_LOW);
+	if (IS_ERR(gpiomtd->nwp)) {
+		ret = PTR_ERR(gpiomtd->nwp);
+		goto out_ce;
 	}
 
-	ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_ale, "NAND ALE");
-	if (ret)
-		return ret;
-	gpio_direction_output(gpiomtd->plat.gpio_ale, 0);
+	gpiomtd->cle = devm_gpiod_get(dev, "cle", GPIOD_OUT_LOW);
+	if (IS_ERR(gpiomtd->cle)) {
+		ret = PTR_ERR(gpiomtd->cle);
+		goto out_ce;
+	}
 
-	ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_cle, "NAND CLE");
-	if (ret)
-		return ret;
-	gpio_direction_output(gpiomtd->plat.gpio_cle, 0);
-
-	if (gpio_is_valid(gpiomtd->plat.gpio_rdy)) {
-		ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_rdy,
-					"NAND RDY");
-		if (ret)
-			return ret;
-		gpio_direction_input(gpiomtd->plat.gpio_rdy);
-		chip->dev_ready = gpio_nand_devready;
+	gpiomtd->rdy = devm_gpiod_get_optional(dev, "rdy", GPIOD_IN);
+	if (IS_ERR(gpiomtd->rdy)) {
+		ret = PTR_ERR(gpiomtd->rdy);
+		goto out_ce;
 	}
+	/* Using RDY pin */
+	if (gpiomtd->rdy)
+		chip->dev_ready = gpio_nand_devready;
 
 	nand_set_flash_node(chip, pdev->dev.of_node);
 	chip->IO_ADDR_W		= chip->IO_ADDR_R;
@@ -285,12 +283,13 @@ static int gpio_nand_probe(struct platform_device *pdev)
 	chip->cmd_ctrl		= gpio_nand_cmd_ctrl;
 
 	mtd			= nand_to_mtd(chip);
-	mtd->dev.parent		= &pdev->dev;
+	mtd->dev.parent		= dev;
 
 	platform_set_drvdata(pdev, gpiomtd);
 
-	if (gpio_is_valid(gpiomtd->plat.gpio_nwp))
-		gpio_direction_output(gpiomtd->plat.gpio_nwp, 1);
+	/* Disable write protection, if wired up */
+	if (gpiomtd->nwp && !IS_ERR(gpiomtd->nwp))
+		gpiod_direction_output(gpiomtd->nwp, 1);
 
 	ret = nand_scan(mtd, 1);
 	if (ret)
@@ -305,8 +304,11 @@ static int gpio_nand_probe(struct platform_device *pdev)
 		return 0;
 
 err_wp:
-	if (gpio_is_valid(gpiomtd->plat.gpio_nwp))
-		gpio_set_value(gpiomtd->plat.gpio_nwp, 0);
+	if (gpiomtd->nwp && !IS_ERR(gpiomtd->nwp))
+		gpiod_set_value(gpiomtd->nwp, 0);
+out_ce:
+	if (gpiomtd->nce && !IS_ERR(gpiomtd->nce))
+		gpiod_set_value(gpiomtd->nce, 0);
 
 	return ret;
 }

drivers/mtd/nand/hisi504_nand.c

@@ -432,8 +432,7 @@ static void set_addr(struct mtd_info *mtd, int column, int page_addr)
 		host->addr_value[0] |= (page_addr & 0xffff)
 			<< (host->addr_cycle * 8);
 		host->addr_cycle    += 2;
-		/* One more address cycle for devices > 128MiB */
-		if (chip->chipsize > (128 << 20)) {
+		if (chip->options & NAND_ROW_ADDR_3) {
 			host->addr_cycle += 1;
 			if (host->command == NAND_CMD_ERASE1)
 				host->addr_value[0] |= ((page_addr >> 16) & 0xff) << 16;

drivers/mtd/nand/mtk_ecc.c

@@ -115,6 +115,11 @@ static irqreturn_t mtk_ecc_irq(int irq, void *id)
 		op = ECC_DECODE;
 		dec = readw(ecc->regs + ECC_DECDONE);
 		if (dec & ecc->sectors) {
+			/*
+			 * Clear decode IRQ status once again to ensure that
+			 * there will be no extra IRQ.
+			 */
+			readw(ecc->regs + ECC_DECIRQ_STA);
 			ecc->sectors = 0;
 			complete(&ecc->done);
 		} else {
@@ -130,8 +135,6 @@ static irqreturn_t mtk_ecc_irq(int irq, void *id)
 		}
 	}
 
-	writel(0, ecc->regs + ECC_IRQ_REG(op));
-
 	return IRQ_HANDLED;
 }
 
@@ -307,6 +310,12 @@ void mtk_ecc_disable(struct mtk_ecc *ecc)
 
 	/* disable it */
 	mtk_ecc_wait_idle(ecc, op);
+	if (op == ECC_DECODE)
+		/*
+		 * Clear decode IRQ status in case there is a timeout to wait
+		 * decode IRQ.
+		 */
+		readw(ecc->regs + ECC_DECIRQ_STA);
 	writew(0, ecc->regs + ECC_IRQ_REG(op));
 	writew(ECC_OP_DISABLE, ecc->regs + ECC_CTL_REG(op));
 

drivers/mtd/nand/mxc_nand.c

@@ -415,7 +415,7 @@ static void send_cmd_v3(struct mxc_nand_host *host, uint16_t cmd, int useirq)
  * waits for completion. */
 static void send_cmd_v1_v2(struct mxc_nand_host *host, uint16_t cmd, int useirq)
 {
-	pr_debug("send_cmd(host, 0x%x, %d)\n", cmd, useirq);
+	dev_dbg(host->dev, "send_cmd(host, 0x%x, %d)\n", cmd, useirq);
 
 	writew(cmd, NFC_V1_V2_FLASH_CMD);
 	writew(NFC_CMD, NFC_V1_V2_CONFIG2);
@@ -431,7 +431,7 @@ static void send_cmd_v1_v2(struct mxc_nand_host *host, uint16_t cmd, int useirq)
 			udelay(1);
 		}
 		if (max_retries < 0)
-			pr_debug("%s: RESET failed\n", __func__);
+			dev_dbg(host->dev, "%s: RESET failed\n", __func__);
 	} else {
 		/* Wait for operation to complete */
 		wait_op_done(host, useirq);
@@ -454,7 +454,7 @@ static void send_addr_v3(struct mxc_nand_host *host, uint16_t addr, int islast)
  * a NAND command. */
 static void send_addr_v1_v2(struct mxc_nand_host *host, uint16_t addr, int islast)
 {
-	pr_debug("send_addr(host, 0x%x %d)\n", addr, islast);
+	dev_dbg(host->dev, "send_addr(host, 0x%x %d)\n", addr, islast);
 
 	writew(addr, NFC_V1_V2_FLASH_ADDR);
 	writew(NFC_ADDR, NFC_V1_V2_CONFIG2);
@@ -607,7 +607,7 @@ static int mxc_nand_correct_data_v1(struct mtd_info *mtd, u_char *dat,
 	uint16_t ecc_status = get_ecc_status_v1(host);
 
 	if (((ecc_status & 0x3) == 2) || ((ecc_status >> 2) == 2)) {
-		pr_debug("MXC_NAND: HWECC uncorrectable 2-bit ECC error\n");
+		dev_dbg(host->dev, "HWECC uncorrectable 2-bit ECC error\n");
 		return -EBADMSG;
 	}
 
@@ -634,7 +634,7 @@ static int mxc_nand_correct_data_v2_v3(struct mtd_info *mtd, u_char *dat,
 	do {
 		err = ecc_stat & ecc_bit_mask;
 		if (err > err_limit) {
-			printk(KERN_WARNING "UnCorrectable RS-ECC Error\n");
+			dev_dbg(host->dev, "UnCorrectable RS-ECC Error\n");
 			return -EBADMSG;
 		} else {
 			ret += err;
@@ -642,7 +642,7 @@ static int mxc_nand_correct_data_v2_v3(struct mtd_info *mtd, u_char *dat,
 		ecc_stat >>= 4;
 	} while (--no_subpages);
 
-	pr_debug("%d Symbol Correctable RS-ECC Error\n", ret);
+	dev_dbg(host->dev, "%d Symbol Correctable RS-ECC Error\n", ret);
 
 	return ret;
 }
@@ -673,7 +673,7 @@ static u_char mxc_nand_read_byte(struct mtd_info *mtd)
 		host->buf_start++;
 	}
 
-	pr_debug("%s: ret=0x%hhx (start=%u)\n", __func__, ret, host->buf_start);
+	dev_dbg(host->dev, "%s: ret=0x%hhx (start=%u)\n", __func__, ret, host->buf_start);
 	return ret;
 }
 
@@ -859,8 +859,7 @@ static void mxc_do_addr_cycle(struct mtd_info *mtd, int column, int page_addr)
 				host->devtype_data->send_addr(host,
 						(page_addr >> 8) & 0xff, true);
 		} else {
-			/* One more address cycle for higher density devices */
-			if (mtd->size >= 0x4000000) {
+			if (nand_chip->options & NAND_ROW_ADDR_3) {
 				/* paddr_8 - paddr_15 */
 				host->devtype_data->send_addr(host,
 						(page_addr >> 8) & 0xff,
@@ -1212,7 +1211,7 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
 	struct nand_chip *nand_chip = mtd_to_nand(mtd);
 	struct mxc_nand_host *host = nand_get_controller_data(nand_chip);
 
-	pr_debug("mxc_nand_command (cmd = 0x%x, col = 0x%x, page = 0x%x)\n",
+	dev_dbg(host->dev, "mxc_nand_command (cmd = 0x%x, col = 0x%x, page = 0x%x)\n",
 	      command, column, page_addr);
 
 	/* Reset command state information */

drivers/mtd/nand/nand_base.c

@@ -115,7 +115,7 @@ static int nand_ooblayout_ecc_lp(struct mtd_info *mtd, int section,
 	struct nand_chip *chip = mtd_to_nand(mtd);
 	struct nand_ecc_ctrl *ecc = &chip->ecc;
 
-	if (section)
+	if (section || !ecc->total)
 		return -ERANGE;
 
 	oobregion->length = ecc->total;
@@ -727,8 +727,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
 		chip->cmd_ctrl(mtd, page_addr, ctrl);
 		ctrl &= ~NAND_CTRL_CHANGE;
 		chip->cmd_ctrl(mtd, page_addr >> 8, ctrl);
-		/* One more address cycle for devices > 32MiB */
-		if (chip->chipsize > (32 << 20))
+		if (chip->options & NAND_ROW_ADDR_3)
 			chip->cmd_ctrl(mtd, page_addr >> 16, ctrl);
 	}
 	chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
@@ -854,8 +853,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
 			chip->cmd_ctrl(mtd, page_addr, ctrl);
 			chip->cmd_ctrl(mtd, page_addr >> 8,
 				       NAND_NCE | NAND_ALE);
-			/* One more address cycle for devices > 128MiB */
-			if (chip->chipsize > (128 << 20))
+			if (chip->options & NAND_ROW_ADDR_3)
 				chip->cmd_ctrl(mtd, page_addr >> 16,
 					       NAND_NCE | NAND_ALE);
 		}
@@ -1246,6 +1244,7 @@ int nand_reset(struct nand_chip *chip, int chipnr)
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(nand_reset);
 
 /**
  * nand_check_erased_buf - check if a buffer contains (almost) only 0xff data
@@ -2799,15 +2798,18 @@ static int panic_nand_write(struct mtd_info *mtd, loff_t to, size_t len,
 			    size_t *retlen, const uint8_t *buf)
 {
 	struct nand_chip *chip = mtd_to_nand(mtd);
+	int chipnr = (int)(to >> chip->chip_shift);
 	struct mtd_oob_ops ops;
 	int ret;
 
-	/* Wait for the device to get ready */
-	panic_nand_wait(mtd, chip, 400);
-
 	/* Grab the device */
 	panic_nand_get_device(chip, mtd, FL_WRITING);
 
+	chip->select_chip(mtd, chipnr);
+
+	/* Wait for the device to get ready */
+	panic_nand_wait(mtd, chip, 400);
+
 	memset(&ops, 0, sizeof(ops));
 	ops.len = len;
 	ops.datbuf = (uint8_t *)buf;
@@ -3999,6 +4001,9 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type)
 		chip->chip_shift += 32 - 1;
 	}
 
+	if (chip->chip_shift - chip->page_shift > 16)
+		chip->options |= NAND_ROW_ADDR_3;
+
 	chip->badblockbits = 8;
 	chip->erase = single_erase;
 
@@ -4700,6 +4705,19 @@ int nand_scan_tail(struct mtd_info *mtd)
 			mtd_set_ooblayout(mtd, &nand_ooblayout_lp_hamming_ops);
 			break;
 		default:
+			/*
+			 * Expose the whole OOB area to users if ECC_NONE
+			 * is passed. We could do that for all kind of
+			 * ->oobsize, but we must keep the old large/small
+			 * page with ECC layout when ->oobsize <= 128 for
+			 * compatibility reasons.
+			 */
+			if (ecc->mode == NAND_ECC_NONE) {
+				mtd_set_ooblayout(mtd,
+						&nand_ooblayout_lp_ops);
+				break;
+			}
+
 			WARN(1, "No oob scheme defined for oobsize %d\n",
 				mtd->oobsize);
 			ret = -EINVAL;

drivers/mtd/nand/nuc900_nand.c

@@ -154,7 +154,7 @@ static void nuc900_nand_command_lp(struct mtd_info *mtd, unsigned int command,
 		if (page_addr != -1) {
 			write_addr_reg(nand, page_addr);
 
-			if (chip->chipsize > (128 << 20)) {
+			if (chip->options & NAND_ROW_ADDR_3) {
 				write_addr_reg(nand, page_addr >> 8);
 				write_addr_reg(nand, page_addr >> 16 | ENDADDR);
 			} else {

drivers/mtd/nand/omap2.c

@@ -1133,129 +1133,172 @@ static u8  bch8_polynomial[] = {0xef, 0x51, 0x2e, 0x09, 0xed, 0x93, 0x9a, 0xc2,
 				0x97, 0x79, 0xe5, 0x24, 0xb5};
 
 /**
- * omap_calculate_ecc_bch - Generate bytes of ECC bytes
+ * _omap_calculate_ecc_bch - Generate ECC bytes for one sector
  * @mtd:	MTD device structure
  * @dat:	The pointer to data on which ecc is computed
  * @ecc_code:	The ecc_code buffer
+ * @i:		The sector number (for a multi sector page)
  *
- * Support calculating of BCH4/8 ecc vectors for the page
+ * Support calculating of BCH4/8/16 ECC vectors for one sector
+ * within a page. Sector number is in @i.
  */
-static int __maybe_unused omap_calculate_ecc_bch(struct mtd_info *mtd,
-					const u_char *dat, u_char *ecc_calc)
+static int _omap_calculate_ecc_bch(struct mtd_info *mtd,
+				   const u_char *dat, u_char *ecc_calc, int i)
 {
 	struct omap_nand_info *info = mtd_to_omap(mtd);
 	int eccbytes	= info->nand.ecc.bytes;
 	struct gpmc_nand_regs	*gpmc_regs = &info->reg;
 	u8 *ecc_code;
-	unsigned long nsectors, bch_val1, bch_val2, bch_val3, bch_val4;
+	unsigned long bch_val1, bch_val2, bch_val3, bch_val4;
 	u32 val;
-	int i, j;
+	int j;
+
+	ecc_code = ecc_calc;
+	switch (info->ecc_opt) {
+	case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
+	case OMAP_ECC_BCH8_CODE_HW:
+		bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]);
+		bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]);
+		bch_val3 = readl(gpmc_regs->gpmc_bch_result2[i]);
+		bch_val4 = readl(gpmc_regs->gpmc_bch_result3[i]);
+		*ecc_code++ = (bch_val4 & 0xFF);
+		*ecc_code++ = ((bch_val3 >> 24) & 0xFF);
+		*ecc_code++ = ((bch_val3 >> 16) & 0xFF);
+		*ecc_code++ = ((bch_val3 >> 8) & 0xFF);
+		*ecc_code++ = (bch_val3 & 0xFF);
+		*ecc_code++ = ((bch_val2 >> 24) & 0xFF);
+		*ecc_code++ = ((bch_val2 >> 16) & 0xFF);
+		*ecc_code++ = ((bch_val2 >> 8) & 0xFF);
+		*ecc_code++ = (bch_val2 & 0xFF);
+		*ecc_code++ = ((bch_val1 >> 24) & 0xFF);
+		*ecc_code++ = ((bch_val1 >> 16) & 0xFF);
+		*ecc_code++ = ((bch_val1 >> 8) & 0xFF);
+		*ecc_code++ = (bch_val1 & 0xFF);
+		break;
+	case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
+	case OMAP_ECC_BCH4_CODE_HW:
+		bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]);
+		bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]);
+		*ecc_code++ = ((bch_val2 >> 12) & 0xFF);
+		*ecc_code++ = ((bch_val2 >> 4) & 0xFF);
+		*ecc_code++ = ((bch_val2 & 0xF) << 4) |
+			((bch_val1 >> 28) & 0xF);
+		*ecc_code++ = ((bch_val1 >> 20) & 0xFF);
+		*ecc_code++ = ((bch_val1 >> 12) & 0xFF);
+		*ecc_code++ = ((bch_val1 >> 4) & 0xFF);
+		*ecc_code++ = ((bch_val1 & 0xF) << 4);
+		break;
+	case OMAP_ECC_BCH16_CODE_HW:
+		val = readl(gpmc_regs->gpmc_bch_result6[i]);
+		ecc_code[0]  = ((val >>  8) & 0xFF);
+		ecc_code[1]  = ((val >>  0) & 0xFF);
+		val = readl(gpmc_regs->gpmc_bch_result5[i]);
+		ecc_code[2]  = ((val >> 24) & 0xFF);
+		ecc_code[3]  = ((val >> 16) & 0xFF);
+		ecc_code[4]  = ((val >>  8) & 0xFF);
+		ecc_code[5]  = ((val >>  0) & 0xFF);
+		val = readl(gpmc_regs->gpmc_bch_result4[i]);
+		ecc_code[6]  = ((val >> 24) & 0xFF);
+		ecc_code[7]  = ((val >> 16) & 0xFF);
+		ecc_code[8]  = ((val >>  8) & 0xFF);
+		ecc_code[9]  = ((val >>  0) & 0xFF);
+		val = readl(gpmc_regs->gpmc_bch_result3[i]);
+		ecc_code[10] = ((val >> 24) & 0xFF);
+		ecc_code[11] = ((val >> 16) & 0xFF);
+		ecc_code[12] = ((val >>  8) & 0xFF);
+		ecc_code[13] = ((val >>  0) & 0xFF);
+		val = readl(gpmc_regs->gpmc_bch_result2[i]);
+		ecc_code[14] = ((val >> 24) & 0xFF);
+		ecc_code[15] = ((val >> 16) & 0xFF);
+		ecc_code[16] = ((val >>  8) & 0xFF);
+		ecc_code[17] = ((val >>  0) & 0xFF);
+		val = readl(gpmc_regs->gpmc_bch_result1[i]);
+		ecc_code[18] = ((val >> 24) & 0xFF);
+		ecc_code[19] = ((val >> 16) & 0xFF);
+		ecc_code[20] = ((val >>  8) & 0xFF);
+		ecc_code[21] = ((val >>  0) & 0xFF);
+		val = readl(gpmc_regs->gpmc_bch_result0[i]);
+		ecc_code[22] = ((val >> 24) & 0xFF);
+		ecc_code[23] = ((val >> 16) & 0xFF);
+		ecc_code[24] = ((val >>  8) & 0xFF);
+		ecc_code[25] = ((val >>  0) & 0xFF);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* ECC scheme specific syndrome customizations */
+	switch (info->ecc_opt) {
+	case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
+		/* Add constant polynomial to remainder, so that
+		 * ECC of blank pages results in 0x0 on reading back
+		 */
+		for (j = 0; j < eccbytes; j++)
+			ecc_calc[j] ^= bch4_polynomial[j];
+		break;
+	case OMAP_ECC_BCH4_CODE_HW:
+		/* Set  8th ECC byte as 0x0 for ROM compatibility */
+		ecc_calc[eccbytes - 1] = 0x0;
+		break;
+	case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
+		/* Add constant polynomial to remainder, so that
+		 * ECC of blank pages results in 0x0 on reading back
+		 */
+		for (j = 0; j < eccbytes; j++)
+			ecc_calc[j] ^= bch8_polynomial[j];
+		break;
+	case OMAP_ECC_BCH8_CODE_HW:
+		/* Set 14th ECC byte as 0x0 for ROM compatibility */
+		ecc_calc[eccbytes - 1] = 0x0;
+		break;
+	case OMAP_ECC_BCH16_CODE_HW:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * omap_calculate_ecc_bch_sw - ECC generator for sector for SW based correction
+ * @mtd:	MTD device structure
+ * @dat:	The pointer to data on which ecc is computed
+ * @ecc_code:	The ecc_code buffer
+ *
+ * Support calculating of BCH4/8/16 ECC vectors for one sector. This is used
+ * when SW based correction is required as ECC is required for one sector
+ * at a time.
+ */
+static int omap_calculate_ecc_bch_sw(struct mtd_info *mtd,
+				     const u_char *dat, u_char *ecc_calc)
+{
+	return _omap_calculate_ecc_bch(mtd, dat, ecc_calc, 0);
+}
+
+/**
+ * omap_calculate_ecc_bch_multi - Generate ECC for multiple sectors
+ * @mtd:	MTD device structure
+ * @dat:	The pointer to data on which ecc is computed
+ * @ecc_code:	The ecc_code buffer
+ *
+ * Support calculating of BCH4/8/16 ecc vectors for the entire page in one go.
+ */
+static int omap_calculate_ecc_bch_multi(struct mtd_info *mtd,
+					const u_char *dat, u_char *ecc_calc)
+{
+	struct omap_nand_info *info = mtd_to_omap(mtd);
+	int eccbytes = info->nand.ecc.bytes;
+	unsigned long nsectors;
+	int i, ret;
 
 	nsectors = ((readl(info->reg.gpmc_ecc_config) >> 4) & 0x7) + 1;
 	for (i = 0; i < nsectors; i++) {
-		ecc_code = ecc_calc;
-		switch (info->ecc_opt) {
-		case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
-		case OMAP_ECC_BCH8_CODE_HW:
-			bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]);
-			bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]);
-			bch_val3 = readl(gpmc_regs->gpmc_bch_result2[i]);
-			bch_val4 = readl(gpmc_regs->gpmc_bch_result3[i]);
-			*ecc_code++ = (bch_val4 & 0xFF);
-			*ecc_code++ = ((bch_val3 >> 24) & 0xFF);
-			*ecc_code++ = ((bch_val3 >> 16) & 0xFF);
-			*ecc_code++ = ((bch_val3 >> 8) & 0xFF);
-			*ecc_code++ = (bch_val3 & 0xFF);
-			*ecc_code++ = ((bch_val2 >> 24) & 0xFF);
-			*ecc_code++ = ((bch_val2 >> 16) & 0xFF);
-			*ecc_code++ = ((bch_val2 >> 8) & 0xFF);
-			*ecc_code++ = (bch_val2 & 0xFF);
-			*ecc_code++ = ((bch_val1 >> 24) & 0xFF);
-			*ecc_code++ = ((bch_val1 >> 16) & 0xFF);
-			*ecc_code++ = ((bch_val1 >> 8) & 0xFF);
-			*ecc_code++ = (bch_val1 & 0xFF);
-			break;
-		case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
-		case OMAP_ECC_BCH4_CODE_HW:
-			bch_val1 = readl(gpmc_regs->gpmc_bch_result0[i]);
-			bch_val2 = readl(gpmc_regs->gpmc_bch_result1[i]);
-			*ecc_code++ = ((bch_val2 >> 12) & 0xFF);
-			*ecc_code++ = ((bch_val2 >> 4) & 0xFF);
-			*ecc_code++ = ((bch_val2 & 0xF) << 4) |
-				((bch_val1 >> 28) & 0xF);
-			*ecc_code++ = ((bch_val1 >> 20) & 0xFF);
-			*ecc_code++ = ((bch_val1 >> 12) & 0xFF);
-			*ecc_code++ = ((bch_val1 >> 4) & 0xFF);
-			*ecc_code++ = ((bch_val1 & 0xF) << 4);
-			break;
-		case OMAP_ECC_BCH16_CODE_HW:
-			val = readl(gpmc_regs->gpmc_bch_result6[i]);
-			ecc_code[0]  = ((val >>  8) & 0xFF);
-			ecc_code[1]  = ((val >>  0) & 0xFF);
-			val = readl(gpmc_regs->gpmc_bch_result5[i]);
-			ecc_code[2]  = ((val >> 24) & 0xFF);
-			ecc_code[3]  = ((val >> 16) & 0xFF);
-			ecc_code[4]  = ((val >>  8) & 0xFF);
-			ecc_code[5]  = ((val >>  0) & 0xFF);
-			val = readl(gpmc_regs->gpmc_bch_result4[i]);
-			ecc_code[6]  = ((val >> 24) & 0xFF);
-			ecc_code[7]  = ((val >> 16) & 0xFF);
-			ecc_code[8]  = ((val >>  8) & 0xFF);
-			ecc_code[9]  = ((val >>  0) & 0xFF);
-			val = readl(gpmc_regs->gpmc_bch_result3[i]);
-			ecc_code[10] = ((val >> 24) & 0xFF);
-			ecc_code[11] = ((val >> 16) & 0xFF);
-			ecc_code[12] = ((val >>  8) & 0xFF);
-			ecc_code[13] = ((val >>  0) & 0xFF);
-			val = readl(gpmc_regs->gpmc_bch_result2[i]);
-			ecc_code[14] = ((val >> 24) & 0xFF);
-			ecc_code[15] = ((val >> 16) & 0xFF);
-			ecc_code[16] = ((val >>  8) & 0xFF);
-			ecc_code[17] = ((val >>  0) & 0xFF);
-			val = readl(gpmc_regs->gpmc_bch_result1[i]);
-			ecc_code[18] = ((val >> 24) & 0xFF);
-			ecc_code[19] = ((val >> 16) & 0xFF);
-			ecc_code[20] = ((val >>  8) & 0xFF);
-			ecc_code[21] = ((val >>  0) & 0xFF);
-			val = readl(gpmc_regs->gpmc_bch_result0[i]);
-			ecc_code[22] = ((val >> 24) & 0xFF);
-			ecc_code[23] = ((val >> 16) & 0xFF);
-			ecc_code[24] = ((val >>  8) & 0xFF);
-			ecc_code[25] = ((val >>  0) & 0xFF);
-			break;
-		default:
-			return -EINVAL;
-		}
-
-		/* ECC scheme specific syndrome customizations */
-		switch (info->ecc_opt) {
-		case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
-			/* Add constant polynomial to remainder, so that
-			 * ECC of blank pages results in 0x0 on reading back */
-			for (j = 0; j < eccbytes; j++)
-				ecc_calc[j] ^= bch4_polynomial[j];
-			break;
-		case OMAP_ECC_BCH4_CODE_HW:
-			/* Set  8th ECC byte as 0x0 for ROM compatibility */
-			ecc_calc[eccbytes - 1] = 0x0;
-			break;
-		case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
-			/* Add constant polynomial to remainder, so that
-			 * ECC of blank pages results in 0x0 on reading back */
-			for (j = 0; j < eccbytes; j++)
-				ecc_calc[j] ^= bch8_polynomial[j];
-			break;
-		case OMAP_ECC_BCH8_CODE_HW:
-			/* Set 14th ECC byte as 0x0 for ROM compatibility */
-			ecc_calc[eccbytes - 1] = 0x0;
-			break;
-		case OMAP_ECC_BCH16_CODE_HW:
-			break;
-		default:
-			return -EINVAL;
-		}
+		ret = _omap_calculate_ecc_bch(mtd, dat, ecc_calc, i);
+		if (ret)
+			return ret;
 
-	ecc_calc += eccbytes;
+		ecc_calc += eccbytes;
 	}
 
 	return 0;
@@ -1496,7 +1539,7 @@ static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
 	chip->write_buf(mtd, buf, mtd->writesize);
 
 	/* Update ecc vector from GPMC result registers */
-	chip->ecc.calculate(mtd, buf, &ecc_calc[0]);
+	omap_calculate_ecc_bch_multi(mtd, buf, &ecc_calc[0]);
 
 	ret = mtd_ooblayout_set_eccbytes(mtd, ecc_calc, chip->oob_poi, 0,
 					 chip->ecc.total);
@@ -1508,6 +1551,72 @@ static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
 	return 0;
 }
 
+/**
+ * omap_write_subpage_bch - BCH hardware ECC based subpage write
+ * @mtd:	mtd info structure
+ * @chip:	nand chip info structure
+ * @offset:	column address of subpage within the page
+ * @data_len:	data length
+ * @buf:	data buffer
+ * @oob_required: must write chip->oob_poi to OOB
+ * @page: page number to write
+ *
+ * OMAP optimized subpage write method.
+ */
+static int omap_write_subpage_bch(struct mtd_info *mtd,
+				  struct nand_chip *chip, u32 offset,
+				  u32 data_len, const u8 *buf,
+				  int oob_required, int page)
+{
+	u8 *ecc_calc = chip->buffers->ecccalc;
+	int ecc_size      = chip->ecc.size;
+	int ecc_bytes     = chip->ecc.bytes;
+	int ecc_steps     = chip->ecc.steps;
+	u32 start_step = offset / ecc_size;
+	u32 end_step   = (offset + data_len - 1) / ecc_size;
+	int step, ret = 0;
+
+	/*
+	 * Write entire page at one go as it would be optimal
+	 * as ECC is calculated by hardware.
+	 * ECC is calculated for all subpages but we choose
+	 * only what we want.
+	 */
+
+	/* Enable GPMC ECC engine */
+	chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
+
+	/* Write data */
+	chip->write_buf(mtd, buf, mtd->writesize);
+
+	for (step = 0; step < ecc_steps; step++) {
+		/* mask ECC of un-touched subpages by padding 0xFF */
+		if (step < start_step || step > end_step)
+			memset(ecc_calc, 0xff, ecc_bytes);
+		else
+			ret = _omap_calculate_ecc_bch(mtd, buf, ecc_calc, step);
+
+		if (ret)
+			return ret;
+
+		buf += ecc_size;
+		ecc_calc += ecc_bytes;
+	}
+
+	/* copy calculated ECC for whole page to chip->buffer->oob */
+	/* this include masked-value(0xFF) for unwritten subpages */
+	ecc_calc = chip->buffers->ecccalc;
+	ret = mtd_ooblayout_set_eccbytes(mtd, ecc_calc, chip->oob_poi, 0,
+					 chip->ecc.total);
+	if (ret)
+		return ret;
+
+	/* write OOB buffer to NAND device */
+	chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+	return 0;
+}
+
 /**
  * omap_read_page_bch - BCH ecc based page read function for entire page
  * @mtd:		mtd info structure
@@ -1544,7 +1653,7 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
 		       chip->ecc.total);
 
 	/* Calculate ecc bytes */
-	chip->ecc.calculate(mtd, buf, ecc_calc);
+	omap_calculate_ecc_bch_multi(mtd, buf, ecc_calc);
 
 	ret = mtd_ooblayout_get_eccbytes(mtd, ecc_code, chip->oob_poi, 0,
 					 chip->ecc.total);
@@ -1588,8 +1697,7 @@ static bool is_elm_present(struct omap_nand_info *info,
 	return true;
 }
 
-static bool omap2_nand_ecc_check(struct omap_nand_info *info,
-				 struct omap_nand_platform_data	*pdata)
+static bool omap2_nand_ecc_check(struct omap_nand_info *info)
 {
 	bool ecc_needs_bch, ecc_needs_omap_bch, ecc_needs_elm;
 
@@ -1804,7 +1912,6 @@ static const struct mtd_ooblayout_ops omap_sw_ooblayout_ops = {
 static int omap_nand_probe(struct platform_device *pdev)
 {
 	struct omap_nand_info		*info;
-	struct omap_nand_platform_data	*pdata = NULL;
 	struct mtd_info			*mtd;
 	struct nand_chip		*nand_chip;
 	int				err;
@@ -1821,29 +1928,10 @@ static int omap_nand_probe(struct platform_device *pdev)
 
 	info->pdev = pdev;
 
-	if (dev->of_node) {
-		if (omap_get_dt_info(dev, info))
-			return -EINVAL;
-	} else {
-		pdata = dev_get_platdata(&pdev->dev);
-		if (!pdata) {
-			dev_err(&pdev->dev, "platform data missing\n");
-			return -EINVAL;
-		}
-
-		info->gpmc_cs = pdata->cs;
-		info->reg = pdata->reg;
-		info->ecc_opt = pdata->ecc_opt;
-		if (pdata->dev_ready)
-			dev_info(&pdev->dev, "pdata->dev_ready is deprecated\n");
-
-		info->xfer_type = pdata->xfer_type;
-		info->devsize = pdata->devsize;
-		info->elm_of_node = pdata->elm_of_node;
-		info->flash_bbt = pdata->flash_bbt;
-	}
+	err = omap_get_dt_info(dev, info);
+	if (err)
+		return err;
 
-	platform_set_drvdata(pdev, info);
 	info->ops = gpmc_omap_get_nand_ops(&info->reg, info->gpmc_cs);
 	if (!info->ops) {
 		dev_err(&pdev->dev, "Failed to get GPMC->NAND interface\n");
@@ -2002,7 +2090,7 @@ static int omap_nand_probe(struct platform_device *pdev)
 		goto return_error;
 	}
 
-	if (!omap2_nand_ecc_check(info, pdata)) {
+	if (!omap2_nand_ecc_check(info)) {
 		err = -EINVAL;
 		goto return_error;
 	}
@@ -2044,7 +2132,7 @@ static int omap_nand_probe(struct platform_device *pdev)
 		nand_chip->ecc.strength		= 4;
 		nand_chip->ecc.hwctl		= omap_enable_hwecc_bch;
 		nand_chip->ecc.correct		= nand_bch_correct_data;
-		nand_chip->ecc.calculate	= omap_calculate_ecc_bch;
+		nand_chip->ecc.calculate	= omap_calculate_ecc_bch_sw;
 		mtd_set_ooblayout(mtd, &omap_sw_ooblayout_ops);
 		/* Reserve one byte for the OMAP marker */
 		oobbytes_per_step		= nand_chip->ecc.bytes + 1;
@@ -2066,9 +2154,9 @@ static int omap_nand_probe(struct platform_device *pdev)
 		nand_chip->ecc.strength		= 4;
 		nand_chip->ecc.hwctl		= omap_enable_hwecc_bch;
 		nand_chip->ecc.correct		= omap_elm_correct_data;
-		nand_chip->ecc.calculate	= omap_calculate_ecc_bch;
 		nand_chip->ecc.read_page	= omap_read_page_bch;
 		nand_chip->ecc.write_page	= omap_write_page_bch;
+		nand_chip->ecc.write_subpage	= omap_write_subpage_bch;
 		mtd_set_ooblayout(mtd, &omap_ooblayout_ops);
 		oobbytes_per_step		= nand_chip->ecc.bytes;
 
@@ -2087,7 +2175,7 @@ static int omap_nand_probe(struct platform_device *pdev)
 		nand_chip->ecc.strength		= 8;
 		nand_chip->ecc.hwctl		= omap_enable_hwecc_bch;
 		nand_chip->ecc.correct		= nand_bch_correct_data;
-		nand_chip->ecc.calculate	= omap_calculate_ecc_bch;
+		nand_chip->ecc.calculate	= omap_calculate_ecc_bch_sw;
 		mtd_set_ooblayout(mtd, &omap_sw_ooblayout_ops);
 		/* Reserve one byte for the OMAP marker */
 		oobbytes_per_step		= nand_chip->ecc.bytes + 1;
@@ -2109,9 +2197,9 @@ static int omap_nand_probe(struct platform_device *pdev)
 		nand_chip->ecc.strength		= 8;
 		nand_chip->ecc.hwctl		= omap_enable_hwecc_bch;
 		nand_chip->ecc.correct		= omap_elm_correct_data;
-		nand_chip->ecc.calculate	= omap_calculate_ecc_bch;
 		nand_chip->ecc.read_page	= omap_read_page_bch;
 		nand_chip->ecc.write_page	= omap_write_page_bch;
+		nand_chip->ecc.write_subpage	= omap_write_subpage_bch;
 		mtd_set_ooblayout(mtd, &omap_ooblayout_ops);
 		oobbytes_per_step		= nand_chip->ecc.bytes;
 
@@ -2131,9 +2219,9 @@ static int omap_nand_probe(struct platform_device *pdev)
 		nand_chip->ecc.strength		= 16;
 		nand_chip->ecc.hwctl		= omap_enable_hwecc_bch;
 		nand_chip->ecc.correct		= omap_elm_correct_data;
-		nand_chip->ecc.calculate	= omap_calculate_ecc_bch;
 		nand_chip->ecc.read_page	= omap_read_page_bch;
 		nand_chip->ecc.write_page	= omap_write_page_bch;
+		nand_chip->ecc.write_subpage	= omap_write_subpage_bch;
 		mtd_set_ooblayout(mtd, &omap_ooblayout_ops);
 		oobbytes_per_step		= nand_chip->ecc.bytes;
 
@@ -2167,10 +2255,9 @@ static int omap_nand_probe(struct platform_device *pdev)
 	if (err)
 		goto return_error;
 
-	if (dev->of_node)
-		mtd_device_register(mtd, NULL, 0);
-	else
-		mtd_device_register(mtd, pdata->parts, pdata->nr_parts);
+	err = mtd_device_register(mtd, NULL, 0);
+	if (err)
+		goto return_error;
 
 	platform_set_drvdata(pdev, mtd);
 

drivers/mtd/nand/pxa3xx_nand.c

@@ -30,6 +30,8 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/platform_data/mtd-nand-pxa3xx.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
 
 #define	CHIP_DELAY_TIMEOUT	msecs_to_jiffies(200)
 #define NAND_STOP_DELAY		msecs_to_jiffies(40)
@@ -45,6 +47,10 @@
  */
 #define INIT_BUFFER_SIZE	2048
 
+/* System control register and bit to enable NAND on some SoCs */
+#define GENCONF_SOC_DEVICE_MUX	0x208
+#define GENCONF_SOC_DEVICE_MUX_NFC_EN BIT(0)
+
 /* registers and bit definitions */
 #define NDCR		(0x00) /* Control register */
 #define NDTR0CS0	(0x04) /* Timing Parameter 0 for CS0 */
@@ -174,6 +180,7 @@ enum {
 enum pxa3xx_nand_variant {
 	PXA3XX_NAND_VARIANT_PXA,
 	PXA3XX_NAND_VARIANT_ARMADA370,
+	PXA3XX_NAND_VARIANT_ARMADA_8K,
 };
 
 struct pxa3xx_nand_host {
@@ -425,6 +432,10 @@ static const struct of_device_id pxa3xx_nand_dt_ids[] = {
 		.compatible = "marvell,armada370-nand",
 		.data       = (void *)PXA3XX_NAND_VARIANT_ARMADA370,
 	},
+	{
+		.compatible = "marvell,armada-8k-nand",
+		.data       = (void *)PXA3XX_NAND_VARIANT_ARMADA_8K,
+	},
 	{}
 };
 MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids);
@@ -825,7 +836,8 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
 		info->retcode = ERR_UNCORERR;
 	if (status & NDSR_CORERR) {
 		info->retcode = ERR_CORERR;
-		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 &&
+		if ((info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
+		     info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K) &&
 		    info->ecc_bch)
 			info->ecc_err_cnt = NDSR_ERR_CNT(status);
 		else
@@ -888,7 +900,8 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
 		nand_writel(info, NDCB0, info->ndcb2);
 
 		/* NDCB3 register is available in NFCv2 (Armada 370/XP SoC) */
-		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
+		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
+		    info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K)
 			nand_writel(info, NDCB0, info->ndcb3);
 	}
 
@@ -1671,7 +1684,8 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
 		chip->options |= NAND_BUSWIDTH_16;
 
 	/* Device detection must be done with ECC disabled */
-	if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
+	if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
+	    info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K)
 		nand_writel(info, NDECCCTRL, 0x0);
 
 	if (pdata->flash_bbt)
@@ -1709,7 +1723,8 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
 	 * (aka splitted) command handling,
 	 */
 	if (mtd->writesize > PAGE_CHUNK_SIZE) {
-		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) {
+		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 ||
+		    info->variant == PXA3XX_NAND_VARIANT_ARMADA_8K) {
 			chip->cmdfunc = nand_cmdfunc_extended;
 		} else {
 			dev_err(&info->pdev->dev,
@@ -1928,6 +1943,24 @@ static int pxa3xx_nand_probe_dt(struct platform_device *pdev)
 	if (!of_id)
 		return 0;
 
+	/*
+	 * Some SoCs like A7k/A8k need to enable manually the NAND
+	 * controller to avoid being bootloader dependent. This is done
+	 * through the use of a single bit in the System Functions registers.
+	 */
+	if (pxa3xx_nand_get_variant(pdev) == PXA3XX_NAND_VARIANT_ARMADA_8K) {
+		struct regmap *sysctrl_base = syscon_regmap_lookup_by_phandle(
+			pdev->dev.of_node, "marvell,system-controller");
+		u32 reg;
+
+		if (IS_ERR(sysctrl_base))
+			return PTR_ERR(sysctrl_base);
+
+		regmap_read(sysctrl_base, GENCONF_SOC_DEVICE_MUX, &reg);
+		reg |= GENCONF_SOC_DEVICE_MUX_NFC_EN;
+		regmap_write(sysctrl_base, GENCONF_SOC_DEVICE_MUX, reg);
+	}
+
 	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
 	if (!pdata)
 		return -ENOMEM;

drivers/mtd/nand/qcom_nandc.c

@@ -22,6 +22,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/delay.h>
+#include <linux/dma/qcom_bam_dma.h>
 
 /* NANDc reg offsets */
 #define	NAND_FLASH_CMD			0x00
@@ -199,6 +200,15 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg,			\
  */
 #define dev_cmd_reg_addr(nandc, reg) ((nandc)->props->dev_cmd_reg_start + (reg))
 
+/* Returns the NAND register physical address */
+#define nandc_reg_phys(chip, offset) ((chip)->base_phys + (offset))
+
+/* Returns the dma address for reg read buffer */
+#define reg_buf_dma_addr(chip, vaddr) \
+	((chip)->reg_read_dma + \
+	((uint8_t *)(vaddr) - (uint8_t *)(chip)->reg_read_buf))
+
+#define QPIC_PER_CW_CMD_ELEMENTS	32
 #define QPIC_PER_CW_CMD_SGL		32
 #define QPIC_PER_CW_DATA_SGL		8
 
@@ -221,8 +231,13 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg,			\
 /*
  * This data type corresponds to the BAM transaction which will be used for all
  * NAND transfers.
+ * @bam_ce - the array of BAM command elements
  * @cmd_sgl - sgl for NAND BAM command pipe
  * @data_sgl - sgl for NAND BAM consumer/producer pipe
+ * @bam_ce_pos - the index in bam_ce which is available for next sgl
+ * @bam_ce_start - the index in bam_ce which marks the start position ce
+ *		   for current sgl. It will be used for size calculation
+ *		   for current sgl
  * @cmd_sgl_pos - current index in command sgl.
  * @cmd_sgl_start - start index in command sgl.
  * @tx_sgl_pos - current index in data sgl for tx.
@@ -231,8 +246,11 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg,			\
  * @rx_sgl_start - start index in data sgl for rx.
  */
 struct bam_transaction {
+	struct bam_cmd_element *bam_ce;
 	struct scatterlist *cmd_sgl;
 	struct scatterlist *data_sgl;
+	u32 bam_ce_pos;
+	u32 bam_ce_start;
 	u32 cmd_sgl_pos;
 	u32 cmd_sgl_start;
 	u32 tx_sgl_pos;
@@ -307,7 +325,8 @@ struct nandc_regs {
  *				controller
  * @dev:			parent device
  * @base:			MMIO base
- * @base_dma:			physical base address of controller registers
+ * @base_phys:			physical base address of controller registers
+ * @base_dma:			dma base address of controller registers
  * @core_clk:			controller clock
  * @aon_clk:			another controller clock
  *
@@ -340,6 +359,7 @@ struct qcom_nand_controller {
 	struct device *dev;
 
 	void __iomem *base;
+	phys_addr_t base_phys;
 	dma_addr_t base_dma;
 
 	struct clk *core_clk;
@@ -462,7 +482,8 @@ alloc_bam_transaction(struct qcom_nand_controller *nandc)
 
 	bam_txn_size =
 		sizeof(*bam_txn) + num_cw *
-		((sizeof(*bam_txn->cmd_sgl) * QPIC_PER_CW_CMD_SGL) +
+		((sizeof(*bam_txn->bam_ce) * QPIC_PER_CW_CMD_ELEMENTS) +
+		(sizeof(*bam_txn->cmd_sgl) * QPIC_PER_CW_CMD_SGL) +
 		(sizeof(*bam_txn->data_sgl) * QPIC_PER_CW_DATA_SGL));
 
 	bam_txn_buf = devm_kzalloc(nandc->dev, bam_txn_size, GFP_KERNEL);
@@ -472,6 +493,10 @@ alloc_bam_transaction(struct qcom_nand_controller *nandc)
 	bam_txn = bam_txn_buf;
 	bam_txn_buf += sizeof(*bam_txn);
 
+	bam_txn->bam_ce = bam_txn_buf;
+	bam_txn_buf +=
+		sizeof(*bam_txn->bam_ce) * QPIC_PER_CW_CMD_ELEMENTS * num_cw;
+
 	bam_txn->cmd_sgl = bam_txn_buf;
 	bam_txn_buf +=
 		sizeof(*bam_txn->cmd_sgl) * QPIC_PER_CW_CMD_SGL * num_cw;
@@ -489,6 +514,8 @@ static void clear_bam_transaction(struct qcom_nand_controller *nandc)
 	if (!nandc->props->is_bam)
 		return;
 
+	bam_txn->bam_ce_pos = 0;
+	bam_txn->bam_ce_start = 0;
 	bam_txn->cmd_sgl_pos = 0;
 	bam_txn->cmd_sgl_start = 0;
 	bam_txn->tx_sgl_pos = 0;
@@ -733,6 +760,66 @@ static int prepare_bam_async_desc(struct qcom_nand_controller *nandc,
 	return 0;
 }
 
+/*
+ * Prepares the command descriptor for BAM DMA which will be used for NAND
+ * register reads and writes. The command descriptor requires the command
+ * to be formed in command element type so this function uses the command
+ * element from bam transaction ce array and fills the same with required
+ * data. A single SGL can contain multiple command elements so
+ * NAND_BAM_NEXT_SGL will be used for starting the separate SGL
+ * after the current command element.
+ */
+static int prep_bam_dma_desc_cmd(struct qcom_nand_controller *nandc, bool read,
+				 int reg_off, const void *vaddr,
+				 int size, unsigned int flags)
+{
+	int bam_ce_size;
+	int i, ret;
+	struct bam_cmd_element *bam_ce_buffer;
+	struct bam_transaction *bam_txn = nandc->bam_txn;
+
+	bam_ce_buffer = &bam_txn->bam_ce[bam_txn->bam_ce_pos];
+
+	/* fill the command desc */
+	for (i = 0; i < size; i++) {
+		if (read)
+			bam_prep_ce(&bam_ce_buffer[i],
+				    nandc_reg_phys(nandc, reg_off + 4 * i),
+				    BAM_READ_COMMAND,
+				    reg_buf_dma_addr(nandc,
+						     (__le32 *)vaddr + i));
+		else
+			bam_prep_ce_le32(&bam_ce_buffer[i],
+					 nandc_reg_phys(nandc, reg_off + 4 * i),
+					 BAM_WRITE_COMMAND,
+					 *((__le32 *)vaddr + i));
+	}
+
+	bam_txn->bam_ce_pos += size;
+
+	/* use the separate sgl after this command */
+	if (flags & NAND_BAM_NEXT_SGL) {
+		bam_ce_buffer = &bam_txn->bam_ce[bam_txn->bam_ce_start];
+		bam_ce_size = (bam_txn->bam_ce_pos -
+				bam_txn->bam_ce_start) *
+				sizeof(struct bam_cmd_element);
+		sg_set_buf(&bam_txn->cmd_sgl[bam_txn->cmd_sgl_pos],
+			   bam_ce_buffer, bam_ce_size);
+		bam_txn->cmd_sgl_pos++;
+		bam_txn->bam_ce_start = bam_txn->bam_ce_pos;
+
+		if (flags & NAND_BAM_NWD) {
+			ret = prepare_bam_async_desc(nandc, nandc->cmd_chan,
+						     DMA_PREP_FENCE |
+						     DMA_PREP_CMD);
+			if (ret)
+				return ret;
+		}
+	}
+
+	return 0;
+}
+
 /*
  * Prepares the data descriptor for BAM DMA which will be used for NAND
  * data reads and writes.
@@ -851,19 +938,22 @@ static int read_reg_dma(struct qcom_nand_controller *nandc, int first,
 {
 	bool flow_control = false;
 	void *vaddr;
-	int size;
 
-	if (first == NAND_READ_ID || first == NAND_FLASH_STATUS)
-		flow_control = true;
+	vaddr = nandc->reg_read_buf + nandc->reg_read_pos;
+	nandc->reg_read_pos += num_regs;
 
 	if (first == NAND_DEV_CMD_VLD || first == NAND_DEV_CMD1)
 		first = dev_cmd_reg_addr(nandc, first);
 
-	size = num_regs * sizeof(u32);
-	vaddr = nandc->reg_read_buf + nandc->reg_read_pos;
-	nandc->reg_read_pos += num_regs;
+	if (nandc->props->is_bam)
+		return prep_bam_dma_desc_cmd(nandc, true, first, vaddr,
+					     num_regs, flags);
+
+	if (first == NAND_READ_ID || first == NAND_FLASH_STATUS)
+		flow_control = true;
 
-	return prep_adm_dma_desc(nandc, true, first, vaddr, size, flow_control);
+	return prep_adm_dma_desc(nandc, true, first, vaddr,
+				 num_regs * sizeof(u32), flow_control);
 }
 
 /*
@@ -880,13 +970,9 @@ static int write_reg_dma(struct qcom_nand_controller *nandc, int first,
 	bool flow_control = false;
 	struct nandc_regs *regs = nandc->regs;
 	void *vaddr;
-	int size;
 
 	vaddr = offset_to_nandc_reg(regs, first);
 
-	if (first == NAND_FLASH_CMD)
-		flow_control = true;
-
 	if (first == NAND_ERASED_CW_DETECT_CFG) {
 		if (flags & NAND_ERASED_CW_SET)
 			vaddr = &regs->erased_cw_detect_cfg_set;
@@ -903,10 +989,15 @@ static int write_reg_dma(struct qcom_nand_controller *nandc, int first,
 	if (first == NAND_DEV_CMD_VLD_RESTORE || first == NAND_DEV_CMD_VLD)
 		first = dev_cmd_reg_addr(nandc, NAND_DEV_CMD_VLD);
 
-	size = num_regs * sizeof(u32);
+	if (nandc->props->is_bam)
+		return prep_bam_dma_desc_cmd(nandc, false, first, vaddr,
+					     num_regs, flags);
+
+	if (first == NAND_FLASH_CMD)
+		flow_control = true;
 
-	return prep_adm_dma_desc(nandc, false, first, vaddr, size,
-				 flow_control);
+	return prep_adm_dma_desc(nandc, false, first, vaddr,
+				 num_regs * sizeof(u32), flow_control);
 }
 
 /*
@@ -1170,7 +1261,8 @@ static int submit_descs(struct qcom_nand_controller *nandc)
 		}
 
 		if (bam_txn->cmd_sgl_pos > bam_txn->cmd_sgl_start) {
-			r = prepare_bam_async_desc(nandc, nandc->cmd_chan, 0);
+			r = prepare_bam_async_desc(nandc, nandc->cmd_chan,
+						   DMA_PREP_CMD);
 			if (r)
 				return r;
 		}
@@ -2705,6 +2797,7 @@ static int qcom_nandc_probe(struct platform_device *pdev)
 	if (IS_ERR(nandc->base))
 		return PTR_ERR(nandc->base);
 
+	nandc->base_phys = res->start;
 	nandc->base_dma = phys_to_dma(dev, (phys_addr_t)res->start);
 
 	nandc->core_clk = devm_clk_get(dev, "core");

drivers/mtd/nand/sh_flctl.c

@@ -1094,14 +1094,11 @@ MODULE_DEVICE_TABLE(of, of_flctl_match);
 
 static struct sh_flctl_platform_data *flctl_parse_dt(struct device *dev)
 {
-	const struct of_device_id *match;
-	struct flctl_soc_config *config;
+	const struct flctl_soc_config *config;
 	struct sh_flctl_platform_data *pdata;
 
-	match = of_match_device(of_flctl_match, dev);
-	if (match)
-		config = (struct flctl_soc_config *)match->data;
-	else {
+	config = of_device_get_match_data(dev);
+	if (!config) {
 		dev_err(dev, "%s: no OF configuration attached\n", __func__);
 		return NULL;
 	}

include/linux/mtd/nand-gpio.h

@@ -4,11 +4,6 @@
 #include <linux/mtd/rawnand.h>
 
 struct gpio_nand_platdata {
-	int	gpio_nce;
-	int	gpio_nwp;
-	int	gpio_cle;
-	int	gpio_ale;
-	int	gpio_rdy;
 	void	(*adjust_parts)(struct gpio_nand_platdata *, size_t);
 	struct mtd_partition *parts;
 	unsigned int num_parts;

include/linux/mtd/rawnand.h

@@ -177,6 +177,9 @@ enum nand_ecc_algo {
  */
 #define NAND_NEED_SCRAMBLING	0x00002000
 
+/* Device needs 3rd row address cycle */
+#define NAND_ROW_ADDR_3		0x00004000
+
 /* Options valid for Samsung large page devices */
 #define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG
 

include/linux/platform_data/mtd-nand-omap2.h

@@ -66,21 +66,4 @@ struct gpmc_nand_regs {
 	/* Deprecated. Do not use */
 	void __iomem	*gpmc_status;
 };
-
-struct omap_nand_platform_data {
-	int			cs;
-	struct mtd_partition	*parts;
-	int			nr_parts;
-	bool			flash_bbt;
-	enum nand_io		xfer_type;
-	int			devsize;
-	enum omap_ecc           ecc_opt;
-
-	struct device_node	*elm_of_node;
-
-	/* deprecated */
-	struct gpmc_nand_regs	reg;
-	struct device_node	*of_node;
-	bool			dev_ready;
-};
 #endif