Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
 - new driver for eGalaxTouch serial touchscreen
 - new driver for TS-4800 touchscreen
 - an update for Goodix touchscreen driver
 - PS/2 mouse module was reworked to limit number of protocols we try on
   pass-through ports to speed up their detection time
 - wacom_w8001 touchscreen driver now reports pen and touch via separate
   instances of input devices
 - other driver changes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (42 commits)
  Input: elantech - mark protocols v2 and v3 as semi-mt
  Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE
  Input: gpio-keys - fix check for disabling unsupported keys
  Input: omap-keypad - remove dead check
  Input: ti_am335x_tsc - fix HWPEN interrupt handling
  Input: omap-keypad - set tasklet data earlier
  Input: rohm_bu21023 - fix handling of retrying firmware update
  Input: ALPS - report v3 pinnacle trackstick device only if is present
  Input: ALPS - detect trackstick presence for v7 protocol
  Input: pcap_ts - use to_delayed_work
  Input: bma150 - constify bma150_cfg structure
  Input: i8042 - add Fujitsu Lifebook U745 to the nomux list
  Input: egalax_ts_serial - fix potential NULL dereference on error
  Input: uinput - sanity check on ff_effects_max and EV_FF
  Input: uinput - rework ABS validation
  Input: uinput - add new UINPUT_DEV_SETUP and UI_ABS_SETUP ioctl
  Input: goodix - use "inverted_[xy]" flags instead of "rotated_screen"
  Input: goodix - add axis swapping and axis inversion support
  Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
  Input: goodix - add power management support
  ...

Documentation/devicetree/bindings/input/touchscreen/goodix.txt

@@ -13,6 +13,17 @@ Required properties:
  - interrupt-parent	: Interrupt controller to which the chip is connected
  - interrupts		: Interrupt to which the chip is connected
 
+Optional properties:
+
+ - irq-gpios		: GPIO pin used for IRQ. The driver uses the
+			  interrupt gpio pin as output to reset the device.
+ - reset-gpios		: GPIO pin used for reset
+
+ - touchscreen-inverted-x  : X axis is inverted (boolean)
+ - touchscreen-inverted-y  : Y axis is inverted (boolean)
+ - touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
+                             (swapping is done after inverting the axis)
+
 Example:
 
 	i2c@00000000 {
@@ -23,6 +34,9 @@ Example:
 			reg = <0x5d>;
 			interrupt-parent = <&gpio>;
 			interrupts = <0 0>;
+
+			irq-gpios = <&gpio1 0 0>;
+			reset-gpios = <&gpio1 1 0>;
 		};
 
 		/* ... */

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt

@@ -9,7 +9,9 @@ Required properties:
 - touchscreen-size-y: vertical resolution of touchscreen (in pixels)
 
 Optional properties:
-- reset-gpio: GPIO connected to the RESET line of the chip
+- reset-gpios: GPIO connected to the RESET line of the chip
+- enable-gpios: GPIO connected to the ENABLE line of the chip
+- wake-gpios: GPIO connected to the WAKE line of the chip
 
 Example:
 

Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt

+* TS-4800 Touchscreen bindings
+
+Required properties:
+- compatible: must be "technologic,ts4800-ts"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- syscon: phandle / integers array that points to the syscon node which
+          describes the FPGA's syscon registers.
+          - phandle to FPGA's syscon
+          - offset to the touchscreen register
+          - offset to the touchscreen enable bit

drivers/gpio/gpiolib-acpi.c

@@ -943,3 +943,46 @@ int acpi_gpio_count(struct device *dev, const char *con_id)
 	}
 	return count;
 }
+
+struct acpi_crs_lookup {
+	struct list_head node;
+	struct acpi_device *adev;
+	const char *con_id;
+};
+
+static DEFINE_MUTEX(acpi_crs_lookup_lock);
+static LIST_HEAD(acpi_crs_lookup_list);
+
+bool acpi_can_fallback_to_crs(struct acpi_device *adev, const char *con_id)
+{
+	struct acpi_crs_lookup *l, *lookup = NULL;
+
+	/* Never allow fallback if the device has properties */
+	if (adev->data.properties || adev->driver_gpios)
+		return false;
+
+	mutex_lock(&acpi_crs_lookup_lock);
+
+	list_for_each_entry(l, &acpi_crs_lookup_list, node) {
+		if (l->adev == adev) {
+			lookup = l;
+			break;
+		}
+	}
+
+	if (!lookup) {
+		lookup = kmalloc(sizeof(*lookup), GFP_KERNEL);
+		if (lookup) {
+			lookup->adev = adev;
+			lookup->con_id = con_id;
+			list_add_tail(&lookup->node, &acpi_crs_lookup_list);
+		}
+	}
+
+	mutex_unlock(&acpi_crs_lookup_lock);
+
+	return lookup &&
+		((!lookup->con_id && !con_id) ||
+		 (lookup->con_id && con_id &&
+		  strcmp(lookup->con_id, con_id) == 0));
+}

drivers/gpio/gpiolib.c

@@ -1874,6 +1874,9 @@ static struct gpio_desc *acpi_find_gpio(struct device *dev, const char *con_id,
 
 	/* Then from plain _CRS GPIOs */
 	if (IS_ERR(desc)) {
+		if (!acpi_can_fallback_to_crs(adev, con_id))
+			return ERR_PTR(-ENOENT);
+
 		desc = acpi_get_gpiod_by_index(adev, NULL, idx, &info);
 		if (IS_ERR(desc))
 			return desc;

drivers/gpio/gpiolib.h

@@ -48,6 +48,8 @@ struct gpio_desc *acpi_node_get_gpiod(struct fwnode_handle *fwnode,
 				      struct acpi_gpio_info *info);
 
 int acpi_gpio_count(struct device *dev, const char *con_id);
+
+bool acpi_can_fallback_to_crs(struct acpi_device *adev, const char *con_id);
 #else
 static inline void acpi_gpiochip_add(struct gpio_chip *chip) { }
 static inline void acpi_gpiochip_remove(struct gpio_chip *chip) { }
@@ -74,6 +76,12 @@ static inline int acpi_gpio_count(struct device *dev, const char *con_id)
 {
 	return -ENODEV;
 }
+
+static inline bool acpi_can_fallback_to_crs(struct acpi_device *adev,
+					    const char *con_id)
+{
+	return false;
+}
 #endif
 
 struct gpio_desc *of_get_named_gpiod_flags(struct device_node *np,

drivers/input/keyboard/gpio_keys.c

@@ -96,13 +96,29 @@ struct gpio_keys_drvdata {
  * Return value of this function can be used to allocate bitmap
  * large enough to hold all bits for given type.
  */
-static inline int get_n_events_by_type(int type)
+static int get_n_events_by_type(int type)
 {
 	BUG_ON(type != EV_SW && type != EV_KEY);
 
 	return (type == EV_KEY) ? KEY_CNT : SW_CNT;
 }
 
+/**
+ * get_bm_events_by_type() - returns bitmap of supported events per @type
+ * @input: input device from which bitmap is retrieved
+ * @type: type of button (%EV_KEY, %EV_SW)
+ *
+ * Return value of this function can be used to allocate bitmap
+ * large enough to hold all bits for given type.
+ */
+static const unsigned long *get_bm_events_by_type(struct input_dev *dev,
+						  int type)
+{
+	BUG_ON(type != EV_SW && type != EV_KEY);
+
+	return (type == EV_KEY) ? dev->keybit : dev->swbit;
+}
+
 /**
  * gpio_keys_disable_button() - disables given GPIO button
  * @bdata: button data for button to be disabled
@@ -213,6 +229,7 @@ static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata,
 					   const char *buf, unsigned int type)
 {
 	int n_events = get_n_events_by_type(type);
+	const unsigned long *bitmap = get_bm_events_by_type(ddata->input, type);
 	unsigned long *bits;
 	ssize_t error;
 	int i;
@@ -226,6 +243,11 @@ static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata,
 		goto out;
 
 	/* First validate */
+	if (!bitmap_subset(bits, bitmap, n_events)) {
+		error = -EINVAL;
+		goto out;
+	}
+
 	for (i = 0; i < ddata->pdata->nbuttons; i++) {
 		struct gpio_button_data *bdata = &ddata->data[i];
 
@@ -239,11 +261,6 @@ static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata,
 		}
 	}
 
-	if (i == ddata->pdata->nbuttons) {
-		error = -EINVAL;
-		goto out;
-	}
-
 	mutex_lock(&ddata->disable_lock);
 
 	for (i = 0; i < ddata->pdata->nbuttons; i++) {

drivers/input/keyboard/omap-keypad.c

@@ -155,14 +155,6 @@ static void omap_kp_tasklet(unsigned long data)
 			       "pressed" : "released");
 #else
 			key = keycodes[MATRIX_SCAN_CODE(row, col, row_shift)];
-			if (key < 0) {
-				printk(KERN_WARNING
-				      "omap-keypad: Spurious key event %d-%d\n",
-				       col, row);
-				/* We scan again after a couple of seconds */
-				spurious = 1;
-				continue;
-			}
 
 			if (!(kp_cur_group == (key & GROUP_MASK) ||
 			      kp_cur_group == -1))
@@ -292,8 +284,8 @@ static int omap_kp_probe(struct platform_device *pdev)
 	setup_timer(&omap_kp->timer, omap_kp_timer, (unsigned long)omap_kp);
 
 	/* get the irq and init timer*/
-	tasklet_enable(&kp_tasklet);
 	kp_tasklet.data = (unsigned long) omap_kp;
+	tasklet_enable(&kp_tasklet);
 
 	ret = device_create_file(&pdev->dev, &dev_attr_enable);
 	if (ret < 0)

drivers/input/misc/bma150.c

@@ -147,7 +147,7 @@ struct bma150_data {
  * are stated and verified by Bosch Sensortec where they are configured
  * to provide a generic sensitivity performance.
  */
-static struct bma150_cfg default_cfg = {
+static const struct bma150_cfg default_cfg = {
 	.any_motion_int = 1,
 	.hg_int = 1,
 	.lg_int = 1,

drivers/input/misc/da9063_onkey.c

@@ -179,13 +179,13 @@ static irqreturn_t da9063_onkey_irq_handler(int irq, void *data)
 		input_report_key(onkey->input, KEY_POWER, 1);
 		input_sync(onkey->input);
 		schedule_delayed_work(&onkey->work, 0);
-		dev_dbg(onkey->dev, "KEY_POWER pressed.\n");
+		dev_dbg(onkey->dev, "KEY_POWER long press.\n");
 	} else {
-		input_report_key(onkey->input, KEY_SLEEP, 1);
+		input_report_key(onkey->input, KEY_POWER, 1);
 		input_sync(onkey->input);
-		input_report_key(onkey->input, KEY_SLEEP, 0);
+		input_report_key(onkey->input, KEY_POWER, 0);
 		input_sync(onkey->input);
-		dev_dbg(onkey->dev, "KEY_SLEEP pressed.\n");
+		dev_dbg(onkey->dev, "KEY_POWER short press.\n");
 	}
 
 	return IRQ_HANDLED;

drivers/input/misc/sparcspkr.c

@@ -345,23 +345,19 @@ static struct platform_driver grover_beep_driver = {
 	.shutdown	= sparcspkr_shutdown,
 };
 
+static struct platform_driver * const drivers[] = {
+	&bbc_beep_driver,
+	&grover_beep_driver,
+};
+
 static int __init sparcspkr_init(void)
 {
-	int err = platform_driver_register(&bbc_beep_driver);
-
-	if (!err) {
-		err = platform_driver_register(&grover_beep_driver);
-		if (err)
-			platform_driver_unregister(&bbc_beep_driver);
-	}
-
-	return err;
+	return platform_register_drivers(drivers, ARRAY_SIZE(drivers));
 }
 
 static void __exit sparcspkr_exit(void)
 {
-	platform_driver_unregister(&bbc_beep_driver);
-	platform_driver_unregister(&grover_beep_driver);
+	platform_unregister_drivers(drivers, ARRAY_SIZE(drivers));
 }
 
 module_init(sparcspkr_init);

drivers/input/misc/uinput.c

@@ -256,13 +256,29 @@ static void uinput_destroy_device(struct uinput_device *udev)
 static int uinput_create_device(struct uinput_device *udev)
 {
 	struct input_dev *dev = udev->dev;
-	int error;
+	int error, nslot;
 
 	if (udev->state != UIST_SETUP_COMPLETE) {
 		printk(KERN_DEBUG "%s: write device info first\n", UINPUT_NAME);
 		return -EINVAL;
 	}
 
+	if (test_bit(ABS_MT_SLOT, dev->absbit)) {
+		nslot = input_abs_get_max(dev, ABS_MT_SLOT) + 1;
+		error = input_mt_init_slots(dev, nslot, 0);
+		if (error)
+			goto fail1;
+	} else if (test_bit(ABS_MT_POSITION_X, dev->absbit)) {
+		input_set_events_per_packet(dev, 60);
+	}
+
+	if (test_bit(EV_FF, dev->evbit) && !udev->ff_effects_max) {
+		printk(KERN_DEBUG "%s: ff_effects_max should be non-zero when FF_BIT is set\n",
+			UINPUT_NAME);
+		error = -EINVAL;
+		goto fail1;
+	}
+
 	if (udev->ff_effects_max) {
 		error = input_ff_create(dev, udev->ff_effects_max);
 		if (error)
@@ -308,51 +324,50 @@ static int uinput_open(struct inode *inode, struct file *file)
 	return 0;
 }
 
-static int uinput_validate_absbits(struct input_dev *dev)
+static int uinput_validate_absinfo(struct input_dev *dev, unsigned int code,
+				   const struct input_absinfo *abs)
 {
-	unsigned int cnt;
-	int nslot;
-
-	if (!test_bit(EV_ABS, dev->evbit))
-		return 0;
-
-	/*
-	 * Check if absmin/absmax/absfuzz/absflat are sane.
-	 */
-
-	for_each_set_bit(cnt, dev->absbit, ABS_CNT) {
 	int min, max;
 
-		min = input_abs_get_min(dev, cnt);
-		max = input_abs_get_max(dev, cnt);
+	min = abs->minimum;
+	max = abs->maximum;
 
 	if ((min != 0 || max != 0) && max <= min) {
 		printk(KERN_DEBUG
 		       "%s: invalid abs[%02x] min:%d max:%d\n",
-				UINPUT_NAME, cnt,
-				input_abs_get_min(dev, cnt),
-				input_abs_get_max(dev, cnt));
+		       UINPUT_NAME, code, min, max);
 		return -EINVAL;
 	}
 
-		if (input_abs_get_flat(dev, cnt) >
-		    input_abs_get_max(dev, cnt) - input_abs_get_min(dev, cnt)) {
+	if (abs->flat > max - min) {
 		printk(KERN_DEBUG
-				"%s: abs_flat #%02x out of range: %d "
-				"(min:%d/max:%d)\n",
-				UINPUT_NAME, cnt,
-				input_abs_get_flat(dev, cnt),
-				input_abs_get_min(dev, cnt),
-				input_abs_get_max(dev, cnt));
+		       "%s: abs_flat #%02x out of range: %d (min:%d/max:%d)\n",
+		       UINPUT_NAME, code, abs->flat, min, max);
 		return -EINVAL;
 	}
-	}
 
-	if (test_bit(ABS_MT_SLOT, dev->absbit)) {
-		nslot = input_abs_get_max(dev, ABS_MT_SLOT) + 1;
-		input_mt_init_slots(dev, nslot, 0);
-	} else if (test_bit(ABS_MT_POSITION_X, dev->absbit)) {
-		input_set_events_per_packet(dev, 60);
+	return 0;
+}
+
+static int uinput_validate_absbits(struct input_dev *dev)
+{
+	unsigned int cnt;
+	int error;
+
+	if (!test_bit(EV_ABS, dev->evbit))
+		return 0;
+
+	/*
+	 * Check if absmin/absmax/absfuzz/absflat are sane.
+	 */
+
+	for_each_set_bit(cnt, dev->absbit, ABS_CNT) {
+		if (!dev->absinfo)
+			return -EINVAL;
+
+		error = uinput_validate_absinfo(dev, cnt, &dev->absinfo[cnt]);
+		if (error)
+			return error;
 	}
 
 	return 0;
@@ -370,7 +385,70 @@ static int uinput_allocate_device(struct uinput_device *udev)
 	return 0;
 }
 
-static int uinput_setup_device(struct uinput_device *udev,
+static int uinput_dev_setup(struct uinput_device *udev,
+			    struct uinput_setup __user *arg)
+{
+	struct uinput_setup setup;
+	struct input_dev *dev;
+
+	if (udev->state == UIST_CREATED)
+		return -EINVAL;
+
+	if (copy_from_user(&setup, arg, sizeof(setup)))
+		return -EFAULT;
+
+	if (!setup.name[0])
+		return -EINVAL;
+
+	dev = udev->dev;
+	dev->id = setup.id;
+	udev->ff_effects_max = setup.ff_effects_max;
+
+	kfree(dev->name);
+	dev->name = kstrndup(setup.name, UINPUT_MAX_NAME_SIZE, GFP_KERNEL);
+	if (!dev->name)
+		return -ENOMEM;
+
+	udev->state = UIST_SETUP_COMPLETE;
+	return 0;
+}
+
+static int uinput_abs_setup(struct uinput_device *udev,
+			    struct uinput_setup __user *arg, size_t size)
+{
+	struct uinput_abs_setup setup = {};
+	struct input_dev *dev;
+	int error;
+
+	if (size > sizeof(setup))
+		return -E2BIG;
+
+	if (udev->state == UIST_CREATED)
+		return -EINVAL;
+
+	if (copy_from_user(&setup, arg, size))
+		return -EFAULT;
+
+	if (setup.code > ABS_MAX)
+		return -ERANGE;
+
+	dev = udev->dev;
+
+	error = uinput_validate_absinfo(dev, setup.code, &setup.absinfo);
+	if (error)
+		return error;
+
+	input_alloc_absinfo(dev);
+	if (!dev->absinfo)
+		return -ENOMEM;
+
+	set_bit(setup.code, dev->absbit);
+	dev->absinfo[setup.code] = setup.absinfo;
+	return 0;
+}
+
+/* legacy setup via write() */
+static int uinput_setup_device_legacy(struct uinput_device *udev,
 				      const char __user *buffer, size_t count)
 {
 	struct uinput_user_dev	*user_dev;
@@ -474,7 +552,7 @@ static ssize_t uinput_write(struct file *file, const char __user *buffer,
 
 	retval = udev->state == UIST_CREATED ?
 			uinput_inject_events(udev, buffer, count) :
-			uinput_setup_device(udev, buffer, count);
+			uinput_setup_device_legacy(udev, buffer, count);
 
 	mutex_unlock(&udev->mutex);
 
@@ -735,6 +813,12 @@ static long uinput_ioctl_handler(struct file *file, unsigned int cmd,
 			uinput_destroy_device(udev);
 			goto out;
 
+		case UI_DEV_SETUP:
+			retval = uinput_dev_setup(udev, p);
+			goto out;
+
+		/* UI_ABS_SETUP is handled in the variable size ioctls */
+
 		case UI_SET_EVBIT:
 			retval = uinput_set_bit(arg, evbit, EV_MAX);
 			goto out;
@@ -879,6 +963,10 @@ static long uinput_ioctl_handler(struct file *file, unsigned int cmd,
 		name = dev_name(&udev->dev->dev);
 		retval = uinput_str_to_user(p, name, size);
 		goto out;
+
+	case UI_ABS_SETUP & ~IOCSIZE_MASK:
+		retval = uinput_abs_setup(udev, p, size);
+		goto out;
 	}
 
 	retval = -EINVAL;

drivers/input/mouse/alps.c

@@ -31,6 +31,7 @@
 #define ALPS_CMD_NIBBLE_10	0x01f2
 
 #define ALPS_REG_BASE_RUSHMORE	0xc2c0
+#define ALPS_REG_BASE_V7	0xc2c0
 #define ALPS_REG_BASE_PINNACLE	0x0000
 
 static const struct alps_nibble_commands alps_v3_nibble_commands[] = {
@@ -2047,7 +2048,7 @@ static int alps_absolute_mode_v3(struct psmouse *psmouse)
 	return 0;
 }
 
-static int alps_probe_trackstick_v3(struct psmouse *psmouse, int reg_base)
+static int alps_probe_trackstick_v3_v7(struct psmouse *psmouse, int reg_base)
 {
 	int ret = -EIO, reg_val;
 
@@ -2128,15 +2129,12 @@ static int alps_setup_trackstick_v3(struct psmouse *psmouse, int reg_base)
 
 static int alps_hw_init_v3(struct psmouse *psmouse)
 {
+	struct alps_data *priv = psmouse->private;
 	struct ps2dev *ps2dev = &psmouse->ps2dev;
 	int reg_val;
 	unsigned char param[4];
 
-	reg_val = alps_probe_trackstick_v3(psmouse, ALPS_REG_BASE_PINNACLE);
-	if (reg_val == -EIO)
-		goto error;
-
-	if (reg_val == 0 &&
+	if ((priv->flags & ALPS_DUALPOINT) &&
 	    alps_setup_trackstick_v3(psmouse, ALPS_REG_BASE_PINNACLE) == -EIO)
 		goto error;
 
@@ -2613,6 +2611,11 @@ static int alps_set_protocol(struct psmouse *psmouse,
 		priv->decode_fields = alps_decode_pinnacle;
 		priv->nibble_commands = alps_v3_nibble_commands;
 		priv->addr_command = PSMOUSE_CMD_RESET_WRAP;
+
+		if (alps_probe_trackstick_v3_v7(psmouse,
+						ALPS_REG_BASE_PINNACLE) < 0)
+			priv->flags &= ~ALPS_DUALPOINT;
+
 		break;
 
 	case ALPS_PROTO_V3_RUSHMORE:
@@ -2625,7 +2628,7 @@ static int alps_set_protocol(struct psmouse *psmouse,
 		priv->x_bits = 16;
 		priv->y_bits = 12;
 
-		if (alps_probe_trackstick_v3(psmouse,
+		if (alps_probe_trackstick_v3_v7(psmouse,
 						ALPS_REG_BASE_RUSHMORE) < 0)
 			priv->flags &= ~ALPS_DUALPOINT;
 
@@ -2676,6 +2679,9 @@ static int alps_set_protocol(struct psmouse *psmouse,
 		if (priv->fw_ver[1] != 0xba)
 			priv->flags |= ALPS_BUTTONPAD;
 
+		if (alps_probe_trackstick_v3_v7(psmouse, ALPS_REG_BASE_V7) < 0)
+			priv->flags &= ~ALPS_DUALPOINT;
+
 		break;
 
 	case ALPS_PROTO_V8:

drivers/input/mouse/elantech.c

@@ -1222,7 +1222,7 @@ static int elantech_set_input_params(struct psmouse *psmouse)
 			input_set_abs_params(dev, ABS_TOOL_WIDTH, ETP_WMIN_V2,
 					     ETP_WMAX_V2, 0, 0);
 		}
-		input_mt_init_slots(dev, 2, 0);
+		input_mt_init_slots(dev, 2, INPUT_MT_SEMI_MT);
 		input_set_abs_params(dev, ABS_MT_POSITION_X, x_min, x_max, 0, 0);
 		input_set_abs_params(dev, ABS_MT_POSITION_Y, y_min, y_max, 0, 0);
 		break;

drivers/input/mouse/focaltech.c

@@ -49,12 +49,6 @@ int focaltech_detect(struct psmouse *psmouse, bool set_properties)
 	return 0;
 }
 
-static void focaltech_reset(struct psmouse *psmouse)
-{
-	ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
-	psmouse_reset(psmouse);
-}
-
 #ifdef CONFIG_MOUSE_PS2_FOCALTECH
 
 /*
@@ -300,6 +294,12 @@ static int focaltech_switch_protocol(struct psmouse *psmouse)
 	return 0;
 }
 
+static void focaltech_reset(struct psmouse *psmouse)
+{
+	ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
+	psmouse_reset(psmouse);
+}
+
 static void focaltech_disconnect(struct psmouse *psmouse)
 {
 	focaltech_reset(psmouse);
@@ -456,14 +456,4 @@ int focaltech_init(struct psmouse *psmouse)
 	kfree(priv);
 	return error;
 }
-
-#else /* CONFIG_MOUSE_PS2_FOCALTECH */
-
-int focaltech_init(struct psmouse *psmouse)
-{
-	focaltech_reset(psmouse);
-
-	return 0;
-}
-
 #endif /* CONFIG_MOUSE_PS2_FOCALTECH */

drivers/input/mouse/focaltech.h

@@ -18,6 +18,14 @@
 #define _FOCALTECH_H
 
 int focaltech_detect(struct psmouse *psmouse, bool set_properties);
+
+#ifdef CONFIG_MOUSE_PS2_FOCALTECH
 int focaltech_init(struct psmouse *psmouse);
+#else
+static inline int focaltech_init(struct psmouse *psmouse)
+{
+	return -ENOSYS;
+}
+#endif
 
 #endif

drivers/input/mouse/logips2pp.c

@@ -325,7 +325,7 @@ static void ps2pp_set_model_properties(struct psmouse *psmouse,
  * that support it.
  */
 
-int ps2pp_init(struct psmouse *psmouse, bool set_properties)
+int ps2pp_detect(struct psmouse *psmouse, bool set_properties)
 {
 	struct ps2dev *ps2dev = &psmouse->ps2dev;
 	unsigned char param[4];

drivers/input/mouse/logips2pp.h

@@ -12,9 +12,9 @@
 #define _LOGIPS2PP_H
 
 #ifdef CONFIG_MOUSE_PS2_LOGIPS2PP
-int ps2pp_init(struct psmouse *psmouse, bool set_properties);
+int ps2pp_detect(struct psmouse *psmouse, bool set_properties);
 #else
-inline int ps2pp_init(struct psmouse *psmouse, bool set_properties)
+static inline int ps2pp_detect(struct psmouse *psmouse, bool set_properties)
 {
 	return -ENOSYS;
 }

drivers/input/serio/i8042-x86ia64io.h

@@ -257,6 +257,13 @@ static const struct dmi_system_id __initconst i8042_dmi_nomux_table[] = {
 			DMI_MATCH(DMI_PRODUCT_NAME, "LifeBook S6230"),
 		},
 	},
+	{
+		/* Fujitsu Lifebook U745 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK U745"),
+		},
+	},
 	{
 		/* Fujitsu T70H */
 		.matches = {

drivers/input/touchscreen/Kconfig

@@ -295,6 +295,16 @@ config TOUCHSCREEN_EGALAX
 	  To compile this driver as a module, choose M here: the
 	  module will be called egalax_ts.
 
+config TOUCHSCREEN_EGALAX_SERIAL
+	tristate "EETI eGalax serial touchscreen"
+	select SERIO
+	help
+	  Say Y here to enable support for serial connected EETI
+	  eGalax touch panels.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called egalax_ts_serial.
+
 config TOUCHSCREEN_FT6236
 	tristate "FT6236 I2C touchscreen"
 	depends on I2C
@@ -324,6 +334,7 @@ config TOUCHSCREEN_FUJITSU
 config TOUCHSCREEN_GOODIX
 	tristate "Goodix I2C touchscreen"
 	depends on I2C
+	depends on GPIOLIB
 	help
 	  Say Y here if you have the Goodix touchscreen (such as one
 	  installed in Onda v975w tablets) connected to your
@@ -927,6 +938,22 @@ config TOUCHSCREEN_TOUCHIT213
 	  To compile this driver as a module, choose M here: the
 	  module will be called touchit213.
 
+config TOUCHSCREEN_TS4800
+	tristate "TS-4800 touchscreen"
+	depends on HAS_IOMEM && OF
+	select MFD_SYSCON
+	select INPUT_POLLDEV
+	help
+	  Say Y here if you have a touchscreen on a TS-4800 board.
+
+	  On TS-4800, the touchscreen is not handled directly by Linux but by
+	  a companion FPGA.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ts4800_ts.
+
 config TOUCHSCREEN_TSC_SERIO
 	tristate "TSC-10/25/40 serial touchscreen support"
 	select SERIO

drivers/input/touchscreen/Makefile

@@ -35,6 +35,7 @@ obj-$(CONFIG_TOUCHSCREEN_EETI)		+= eeti_ts.o
 obj-$(CONFIG_TOUCHSCREEN_ELAN)		+= elants_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ELO)		+= elo.o
 obj-$(CONFIG_TOUCHSCREEN_EGALAX)	+= egalax_ts.o
+obj-$(CONFIG_TOUCHSCREEN_EGALAX_SERIAL)	+= egalax_ts_serial.o
 obj-$(CONFIG_TOUCHSCREEN_FT6236)	+= ft6236.o
 obj-$(CONFIG_TOUCHSCREEN_FUJITSU)	+= fujitsu_ts.o
 obj-$(CONFIG_TOUCHSCREEN_GOODIX)	+= goodix.o
@@ -68,6 +69,7 @@ obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC)	+= ti_am335x_tsc.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN)	+= touchwin.o
+obj-$(CONFIG_TOUCHSCREEN_TS4800)	+= ts4800-ts.o
 obj-$(CONFIG_TOUCHSCREEN_TSC_SERIO)	+= tsc40.o
 obj-$(CONFIG_TOUCHSCREEN_TSC200X_CORE)	+= tsc200x-core.o
 obj-$(CONFIG_TOUCHSCREEN_TSC2004)	+= tsc2004.o

drivers/input/touchscreen/egalax_ts_serial.c

+/*
+ * EETI Egalax serial touchscreen driver
+ *
+ * Copyright (c) 2015 Zoltán Böszörményi <zboszor@pr.hu>
+ *
+ * based on the
+ *
+ * Hampshire serial touchscreen driver (Copyright (c) 2010 Adam Bennett)
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/input.h>
+#include <linux/serio.h>
+
+#define DRIVER_DESC	"EETI Egalax serial touchscreen driver"
+
+/*
+ * Definitions & global arrays.
+ */
+
+#define EGALAX_FORMAT_MAX_LENGTH	6
+#define EGALAX_FORMAT_START_BIT		BIT(7)
+#define EGALAX_FORMAT_PRESSURE_BIT	BIT(6)
+#define EGALAX_FORMAT_TOUCH_BIT		BIT(0)
+#define EGALAX_FORMAT_RESOLUTION_MASK	0x06
+
+#define EGALAX_MIN_XC			0
+#define EGALAX_MAX_XC			0x4000
+#define EGALAX_MIN_YC			0
+#define EGALAX_MAX_YC			0x4000
+
+/*
+ * Per-touchscreen data.
+ */
+struct egalax {
+	struct input_dev *input;
+	struct serio *serio;
+	int idx;
+	u8 data[EGALAX_FORMAT_MAX_LENGTH];
+	char phys[32];
+};
+
+static void egalax_process_data(struct egalax *egalax)
+{
+	struct input_dev *dev = egalax->input;
+	u8 *data = egalax->data;
+	u16 x, y;
+	u8 shift;
+	u8 mask;
+
+	shift = 3 - ((data[0] & EGALAX_FORMAT_RESOLUTION_MASK) >> 1);
+	mask = 0xff >> (shift + 1);
+
+	x = (((u16)(data[1] & mask) << 7) | (data[2] & 0x7f)) << shift;
+	y = (((u16)(data[3] & mask) << 7) | (data[4] & 0x7f)) << shift;
+
+	input_report_key(dev, BTN_TOUCH, data[0] & EGALAX_FORMAT_TOUCH_BIT);
+	input_report_abs(dev, ABS_X, x);
+	input_report_abs(dev, ABS_Y, y);
+	input_sync(dev);
+}
+
+static irqreturn_t egalax_interrupt(struct serio *serio,
+				    unsigned char data, unsigned int flags)
+{
+	struct egalax *egalax = serio_get_drvdata(serio);
+	int pkt_len;
+
+	egalax->data[egalax->idx++] = data;
+
+	if (likely(egalax->data[0] & EGALAX_FORMAT_START_BIT)) {
+		pkt_len = egalax->data[0] & EGALAX_FORMAT_PRESSURE_BIT ? 6 : 5;
+		if (pkt_len == egalax->idx) {
+			egalax_process_data(egalax);
+			egalax->idx = 0;
+		}
+	} else {
+		dev_dbg(&serio->dev, "unknown/unsynchronized data: %x\n",
+			egalax->data[0]);
+		egalax->idx = 0;
+	}
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * egalax_connect() is the routine that is called when someone adds a
+ * new serio device that supports egalax protocol and registers it as
+ * an input device. This is usually accomplished using inputattach.
+ */
+static int egalax_connect(struct serio *serio, struct serio_driver *drv)
+{
+	struct egalax *egalax;
+	struct input_dev *input_dev;
+	int error;
+
+	egalax = kzalloc(sizeof(struct egalax), GFP_KERNEL);
+	input_dev = input_allocate_device();
+	if (!egalax || !input_dev) {
+		error = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	egalax->serio = serio;
+	egalax->input = input_dev;
+	snprintf(egalax->phys, sizeof(egalax->phys),
+		 "%s/input0", serio->phys);
+
+	input_dev->name = "EETI eGalaxTouch Serial TouchScreen";
+	input_dev->phys = egalax->phys;
+	input_dev->id.bustype = BUS_RS232;
+	input_dev->id.vendor = SERIO_EGALAX;
+	input_dev->id.product = 0;
+	input_dev->id.version = 0x0001;
+	input_dev->dev.parent = &serio->dev;
+
+	input_set_capability(input_dev, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(input_dev, ABS_X,
+			     EGALAX_MIN_XC, EGALAX_MAX_XC, 0, 0);
+	input_set_abs_params(input_dev, ABS_Y,
+			     EGALAX_MIN_YC, EGALAX_MAX_YC, 0, 0);
+
+	serio_set_drvdata(serio, egalax);
+
+	error = serio_open(serio, drv);
+	if (error)
+		goto err_reset_drvdata;
+
+	error = input_register_device(input_dev);
+	if (error)
+		goto err_close_serio;
+
+	return 0;
+
+err_close_serio:
+	serio_close(serio);
+err_reset_drvdata:
+	serio_set_drvdata(serio, NULL);
+err_free_mem:
+	input_free_device(input_dev);
+	kfree(egalax);
+	return error;
+}
+
+static void egalax_disconnect(struct serio *serio)
+{
+	struct egalax *egalax = serio_get_drvdata(serio);
+
+	serio_close(serio);
+	serio_set_drvdata(serio, NULL);
+	input_unregister_device(egalax->input);
+	kfree(egalax);
+}
+
+/*
+ * The serio driver structure.
+ */
+
+static const struct serio_device_id egalax_serio_ids[] = {
+	{
+		.type	= SERIO_RS232,
+		.proto	= SERIO_EGALAX,
+		.id	= SERIO_ANY,
+		.extra	= SERIO_ANY,
+	},
+	{ 0 }
+};
+
+MODULE_DEVICE_TABLE(serio, egalax_serio_ids);
+
+static struct serio_driver egalax_drv = {
+	.driver		= {
+		.name	= "egalax",
+	},
+	.description	= DRIVER_DESC,
+	.id_table	= egalax_serio_ids,
+	.interrupt	= egalax_interrupt,
+	.connect	= egalax_connect,
+	.disconnect	= egalax_disconnect,
+};
+module_serio_driver(egalax_drv);
+
+MODULE_AUTHOR("Zoltán Böszörményi <zboszor@pr.hu>");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL v2");

drivers/input/touchscreen/pcap_ts.c

@@ -87,7 +87,7 @@ static void pcap_ts_read_xy(void *data, u16 res[2])
 
 static void pcap_ts_work(struct work_struct *work)
 {
-	struct delayed_work *dw = container_of(work, struct delayed_work, work);
+	struct delayed_work *dw = to_delayed_work(work);
 	struct pcap_ts *pcap_ts = container_of(dw, struct pcap_ts, work);
 	u8 ch[2];
 

drivers/input/touchscreen/pixcir_i2c_ts.c

@@ -38,6 +38,8 @@ struct pixcir_i2c_ts_data {
 	struct input_dev *input;
 	struct gpio_desc *gpio_attb;
 	struct gpio_desc *gpio_reset;
+	struct gpio_desc *gpio_enable;
+	struct gpio_desc *gpio_wake;
 	const struct pixcir_i2c_chip_data *chip;
 	int max_fingers;	/* Max fingers supported in this instance */
 	bool running;
@@ -208,6 +210,11 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 	struct device *dev = &ts->client->dev;
 	int ret;
 
+	if (mode == PIXCIR_POWER_ACTIVE || mode == PIXCIR_POWER_IDLE) {
+		if (ts->gpio_wake)
+			gpiod_set_value_cansleep(ts->gpio_wake, 1);
+	}
+
 	ret = i2c_smbus_read_byte_data(ts->client, PIXCIR_REG_POWER_MODE);
 	if (ret < 0) {
 		dev_err(dev, "%s: can't read reg 0x%x : %d\n",
@@ -228,6 +235,11 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 		return ret;
 	}
 
+	if (mode == PIXCIR_POWER_HALT) {
+		if (ts->gpio_wake)
+			gpiod_set_value_cansleep(ts->gpio_wake, 0);
+	}
+
 	return 0;
 }
 
@@ -302,6 +314,11 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
 	struct device *dev = &ts->client->dev;
 	int error;
 
+	if (ts->gpio_enable) {
+		gpiod_set_value_cansleep(ts->gpio_enable, 1);
+		msleep(100);
+	}
+
 	/* LEVEL_TOUCH interrupt with active low polarity */
 	error = pixcir_set_int_mode(ts, PIXCIR_INT_LEVEL_TOUCH, 0);
 	if (error) {
@@ -343,6 +360,9 @@ static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
 	/* Wait till running ISR is complete */
 	synchronize_irq(ts->client->irq);
 
+	if (ts->gpio_enable)
+		gpiod_set_value_cansleep(ts->gpio_enable, 0);
+
 	return 0;
 }
 
@@ -534,6 +554,27 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
+	tsdata->gpio_wake = devm_gpiod_get_optional(dev, "wake",
+						    GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_wake)) {
+		error = PTR_ERR(tsdata->gpio_wake);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to get wake gpio: %d\n", error);
+		return error;
+	}
+
+	tsdata->gpio_enable = devm_gpiod_get_optional(dev, "enable",
+						      GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_enable)) {
+		error = PTR_ERR(tsdata->gpio_enable);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to get enable gpio: %d\n", error);
+		return error;
+	}
+
+	if (tsdata->gpio_enable)
+		msleep(100);
+
 	error = devm_request_threaded_irq(dev, client->irq, NULL, pixcir_ts_isr,
 					  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 					  client->name, tsdata);

drivers/input/touchscreen/rohm_bu21023.c

@@ -725,7 +725,7 @@ static int rohm_ts_load_firmware(struct i2c_client *client,
 			break;
 
 		error = -EIO;
-	} while (++retry >= FIRMWARE_RETRY_MAX);
+	} while (++retry <= FIRMWARE_RETRY_MAX);
 
 out:
 	error2 = i2c_smbus_write_byte_data(client, INT_MASK, INT_ALL);

drivers/input/touchscreen/ti_am335x_tsc.c

@@ -273,8 +273,6 @@ static irqreturn_t titsc_irq(int irq, void *dev)
 	status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
 	if (status & IRQENB_HW_PEN) {
 		ts_dev->pen_down = true;
-		titsc_writel(ts_dev, REG_IRQWAKEUP, 0x00);
-		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
 		irqclr |= IRQENB_HW_PEN;
 	}
 

drivers/input/touchscreen/ts4800-ts.c

+/*
+ * Touchscreen driver for the TS-4800 board
+ *
+ * Copyright (c) 2015 - Savoir-faire Linux
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/bitops.h>
+#include <linux/input.h>
+#include <linux/input-polldev.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* polling interval in ms */
+#define POLL_INTERVAL		3
+
+#define DEBOUNCE_COUNT		1
+
+/* sensor values are 12-bit wide */
+#define MAX_12BIT		((1 << 12) - 1)
+
+#define PENDOWN_MASK		0x1
+
+#define X_OFFSET		0x0
+#define Y_OFFSET		0x2
+
+struct ts4800_ts {
+	struct input_polled_dev *poll_dev;
+	struct device           *dev;
+	char                    phys[32];
+
+	void __iomem            *base;
+	struct regmap           *regmap;
+	unsigned int            reg;
+	unsigned int            bit;
+
+	bool                    pendown;
+	int                     debounce;
+};
+
+static void ts4800_ts_open(struct input_polled_dev *dev)
+{
+	struct ts4800_ts *ts = dev->private;
+	int ret;
+
+	ts->pendown = false;
+	ts->debounce = DEBOUNCE_COUNT;
+
+	ret = regmap_update_bits(ts->regmap, ts->reg, ts->bit, ts->bit);
+	if (ret)
+		dev_warn(ts->dev, "Failed to enable touchscreen\n");
+}
+
+static void ts4800_ts_close(struct input_polled_dev *dev)
+{
+	struct ts4800_ts *ts = dev->private;
+	int ret;
+
+	ret = regmap_update_bits(ts->regmap, ts->reg, ts->bit, 0);
+	if (ret)
+		dev_warn(ts->dev, "Failed to disable touchscreen\n");
+
+}
+
+static void ts4800_ts_poll(struct input_polled_dev *dev)
+{
+	struct input_dev *input_dev = dev->input;
+	struct ts4800_ts *ts = dev->private;
+	u16 last_x = readw(ts->base + X_OFFSET);
+	u16 last_y = readw(ts->base + Y_OFFSET);
+	bool pendown = last_x & PENDOWN_MASK;
+
+	if (pendown) {
+		if (ts->debounce) {
+			ts->debounce--;
+			return;
+		}
+
+		if (!ts->pendown) {
+			input_report_key(input_dev, BTN_TOUCH, 1);
+			ts->pendown = true;
+		}
+
+		last_x = ((~last_x) >> 4) & MAX_12BIT;
+		last_y = ((~last_y) >> 4) & MAX_12BIT;
+
+		input_report_abs(input_dev, ABS_X, last_x);
+		input_report_abs(input_dev, ABS_Y, last_y);
+		input_sync(input_dev);
+	} else if (ts->pendown) {
+		ts->pendown = false;
+		ts->debounce = DEBOUNCE_COUNT;
+		input_report_key(input_dev, BTN_TOUCH, 0);
+		input_sync(input_dev);
+	}
+}
+
+static int ts4800_parse_dt(struct platform_device *pdev,
+			   struct ts4800_ts *ts)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *syscon_np;
+	u32 reg, bit;
+	int error;
+
+	syscon_np = of_parse_phandle(np, "syscon", 0);
+	if (!syscon_np) {
+		dev_err(dev, "no syscon property\n");
+		return -ENODEV;
+	}
+
+	error = of_property_read_u32_index(np, "syscon", 1, &reg);
+	if (error < 0) {
+		dev_err(dev, "no offset in syscon\n");
+		return error;
+	}
+
+	ts->reg = reg;
+
+	error = of_property_read_u32_index(np, "syscon", 2, &bit);
+	if (error < 0) {
+		dev_err(dev, "no bit in syscon\n");
+		return error;
+	}
+
+	ts->bit = BIT(bit);
+
+	ts->regmap = syscon_node_to_regmap(syscon_np);
+	if (IS_ERR(ts->regmap)) {
+		dev_err(dev, "cannot get parent's regmap\n");
+		return PTR_ERR(ts->regmap);
+	}
+
+	return 0;
+}
+
+static int ts4800_ts_probe(struct platform_device *pdev)
+{
+	struct input_polled_dev *poll_dev;
+	struct ts4800_ts *ts;
+	struct resource *res;
+	int error;
+
+	ts = devm_kzalloc(&pdev->dev, sizeof(*ts), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	error = ts4800_parse_dt(pdev, ts);
+	if (error)
+		return error;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ts->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ts->base))
+		return PTR_ERR(ts->base);
+
+	poll_dev = devm_input_allocate_polled_device(&pdev->dev);
+	if (!poll_dev)
+		return -ENOMEM;
+
+	snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(&pdev->dev));
+	ts->poll_dev = poll_dev;
+	ts->dev = &pdev->dev;
+
+	poll_dev->private = ts;
+	poll_dev->poll_interval = POLL_INTERVAL;
+	poll_dev->open = ts4800_ts_open;
+	poll_dev->close = ts4800_ts_close;
+	poll_dev->poll = ts4800_ts_poll;
+
+	poll_dev->input->name = "TS-4800 Touchscreen";
+	poll_dev->input->phys = ts->phys;
+
+	input_set_capability(poll_dev->input, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(poll_dev->input, ABS_X, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(poll_dev->input, ABS_Y, 0, MAX_12BIT, 0, 0);
+
+	error = input_register_polled_device(poll_dev);
+	if (error) {
+		dev_err(&pdev->dev,
+			"Unabled to register polled input device (%d)\n",
+			error);
+		return error;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id ts4800_ts_of_match[] = {
+	{ .compatible = "technologic,ts4800-ts", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ts4800_ts_of_match);
+
+static struct platform_driver ts4800_ts_driver = {
+	.driver = {
+		.name = "ts4800-ts",
+		.of_match_table = ts4800_ts_of_match,
+	},
+	.probe = ts4800_ts_probe,
+};
+module_platform_driver(ts4800_ts_driver);
+
+MODULE_AUTHOR("Damien Riegel <damien.riegel@savoirfairelinux.com>");
+MODULE_DESCRIPTION("TS-4800 Touchscreen Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:ts4800_ts");

include/linux/uinput.h

@@ -20,6 +20,11 @@
  * Author: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
  *
  * Changes/Revisions:
+ *	0.5	08/13/2015 (David Herrmann <dh.herrmann@gmail.com> &
+ *			    Benjamin Tissoires <benjamin.tissoires@redhat.com>)
+ *		- add UI_DEV_SETUP ioctl
+ *		- add UI_ABS_SETUP ioctl
+ *		- add UI_GET_VERSION ioctl
  *	0.4	01/09/2014 (Benjamin Tissoires <benjamin.tissoires@redhat.com>)
  *		- add UI_GET_SYSNAME ioctl
  *	0.3	24/05/2006 (Anssi Hannula <anssi.hannulagmail.com>)

include/uapi/linux/serio.h

@@ -77,5 +77,6 @@
 #define SERIO_PS2MULT	0x3c
 #define SERIO_TSC40	0x3d
 #define SERIO_WACOM_IV	0x3e
+#define SERIO_EGALAX	0x3f
 
 #endif /* _UAPI_SERIO_H */

include/uapi/linux/uinput.h

@@ -20,6 +20,11 @@
  * Author: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
  *
  * Changes/Revisions:
+ *	0.5	08/13/2015 (David Herrmann <dh.herrmann@gmail.com> &
+ *			    Benjamin Tissoires <benjamin.tissoires@redhat.com>)
+ *		- add UI_DEV_SETUP ioctl
+ *		- add UI_ABS_SETUP ioctl
+ *		- add UI_GET_VERSION ioctl
  *	0.4	01/09/2014 (Benjamin Tissoires <benjamin.tissoires@redhat.com>)
  *		- add UI_GET_SYSNAME ioctl
  *	0.3	24/05/2006 (Anssi Hannula <anssi.hannulagmail.com>)
@@ -37,8 +42,8 @@
 #include <linux/types.h>
 #include <linux/input.h>
 
-#define UINPUT_VERSION		4
-
+#define UINPUT_VERSION		5
+#define UINPUT_MAX_NAME_SIZE	80
 
 struct uinput_ff_upload {
 	__u32			request_id;
@@ -58,6 +63,76 @@ struct uinput_ff_erase {
 #define UI_DEV_CREATE		_IO(UINPUT_IOCTL_BASE, 1)
 #define UI_DEV_DESTROY		_IO(UINPUT_IOCTL_BASE, 2)
 
+struct uinput_setup {
+	struct input_id id;
+	char name[UINPUT_MAX_NAME_SIZE];
+	__u32 ff_effects_max;
+};
+
+/**
+ * UI_DEV_SETUP - Set device parameters for setup
+ *
+ * This ioctl sets parameters for the input device to be created.  It
+ * supersedes the old "struct uinput_user_dev" method, which wrote this data
+ * via write(). To actually set the absolute axes UI_ABS_SETUP should be
+ * used.
+ *
+ * The ioctl takes a "struct uinput_setup" object as argument. The fields of
+ * this object are as follows:
+ *              id: See the description of "struct input_id". This field is
+ *                  copied unchanged into the new device.
+ *            name: This is used unchanged as name for the new device.
+ *  ff_effects_max: This limits the maximum numbers of force-feedback effects.
+ *                  See below for a description of FF with uinput.
+ *
+ * This ioctl can be called multiple times and will overwrite previous values.
+ * If this ioctl fails with -EINVAL, it is recommended to use the old
+ * "uinput_user_dev" method via write() as a fallback, in case you run on an
+ * old kernel that does not support this ioctl.
+ *
+ * This ioctl may fail with -EINVAL if it is not supported or if you passed
+ * incorrect values, -ENOMEM if the kernel runs out of memory or -EFAULT if the
+ * passed uinput_setup object cannot be read/written.
+ * If this call fails, partial data may have already been applied to the
+ * internal device.
+ */
+#define UI_DEV_SETUP _IOW(UINPUT_IOCTL_BASE, 3, struct uinput_setup)
+
+struct uinput_abs_setup {
+	__u16  code; /* axis code */
+	/* __u16 filler; */
+	struct input_absinfo absinfo;
+};
+
+/**
+ * UI_ABS_SETUP - Set absolute axis information for the device to setup
+ *
+ * This ioctl sets one absolute axis information for the input device to be
+ * created. It supersedes the old "struct uinput_user_dev" method, which wrote
+ * part of this data and the content of UI_DEV_SETUP via write().
+ *
+ * The ioctl takes a "struct uinput_abs_setup" object as argument. The fields
+ * of this object are as follows:
+ *            code: The corresponding input code associated with this axis
+ *                  (ABS_X, ABS_Y, etc...)
+ *         absinfo: See "struct input_absinfo" for a description of this field.
+ *                  This field is copied unchanged into the kernel for the
+ *                  specified axis. If the axis is not enabled via
+ *                  UI_SET_ABSBIT, this ioctl will enable it.
+ *
+ * This ioctl can be called multiple times and will overwrite previous values.
+ * If this ioctl fails with -EINVAL, it is recommended to use the old
+ * "uinput_user_dev" method via write() as a fallback, in case you run on an
+ * old kernel that does not support this ioctl.
+ *
+ * This ioctl may fail with -EINVAL if it is not supported or if you passed
+ * incorrect values, -ENOMEM if the kernel runs out of memory or -EFAULT if the
+ * passed uinput_setup object cannot be read/written.
+ * If this call fails, partial data may have already been applied to the
+ * internal device.
+ */
+#define UI_ABS_SETUP _IOW(UINPUT_IOCTL_BASE, 4, struct uinput_abs_setup)
+
 #define UI_SET_EVBIT		_IOW(UINPUT_IOCTL_BASE, 100, int)
 #define UI_SET_KEYBIT		_IOW(UINPUT_IOCTL_BASE, 101, int)
 #define UI_SET_RELBIT		_IOW(UINPUT_IOCTL_BASE, 102, int)
@@ -144,7 +219,6 @@ struct uinput_ff_erase {
 #define UI_FF_UPLOAD		1
 #define UI_FF_ERASE		2
 
-#define UINPUT_MAX_NAME_SIZE	80
 struct uinput_user_dev {
 	char name[UINPUT_MAX_NAME_SIZE];
 	struct input_id id;