Commit 1d01145f authored by René van Dorst's avatar René van Dorst Committed by David S. Miller

net: dsa: mt7530: use resolved link config in mac_link_up()

Convert the mt7530 switch driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: default avatarRené van Dorst <opensource@vdorst.com>
Tested-by: default avatarSean Wang <sean.wang@mediatek.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 336aa67b
......@@ -563,17 +563,6 @@ mt7530_mib_reset(struct dsa_switch *ds)
mt7530_write(priv, MT7530_MIB_CCR, CCR_MIB_ACTIVATE);
}
static void
mt7530_port_set_status(struct mt7530_priv *priv, int port, int enable)
{
u32 mask = PMCR_TX_EN | PMCR_RX_EN | PMCR_FORCE_LNK;
if (enable)
mt7530_set(priv, MT7530_PMCR_P(port), mask);
else
mt7530_clear(priv, MT7530_PMCR_P(port), mask);
}
static int mt7530_phy_read(struct dsa_switch *ds, int port, int regnum)
{
struct mt7530_priv *priv = ds->priv;
......@@ -750,7 +739,7 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
priv->ports[port].enable = true;
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
priv->ports[port].pm);
mt7530_port_set_status(priv, port, 0);
mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
mutex_unlock(&priv->reg_mutex);
......@@ -773,7 +762,7 @@ mt7530_port_disable(struct dsa_switch *ds, int port)
priv->ports[port].enable = false;
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
PCR_MATRIX_CLR);
mt7530_port_set_status(priv, port, 0);
mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
mutex_unlock(&priv->reg_mutex);
}
......@@ -1499,8 +1488,7 @@ static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
mcr_new = mcr_cur;
mcr_new &= ~(PMCR_FORCE_SPEED_1000 | PMCR_FORCE_SPEED_100 |
PMCR_FORCE_FDX | PMCR_TX_FC_EN | PMCR_RX_FC_EN);
mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
PMCR_BACKPR_EN | PMCR_FORCE_MODE;
......@@ -1508,22 +1496,6 @@ static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
if (port == 5 && dsa_is_user_port(ds, 5))
mcr_new |= PMCR_EXT_PHY;
switch (state->speed) {
case SPEED_1000:
mcr_new |= PMCR_FORCE_SPEED_1000;
break;
case SPEED_100:
mcr_new |= PMCR_FORCE_SPEED_100;
break;
}
if (state->duplex == DUPLEX_FULL) {
mcr_new |= PMCR_FORCE_FDX;
if (state->pause & MLO_PAUSE_TX)
mcr_new |= PMCR_TX_FC_EN;
if (state->pause & MLO_PAUSE_RX)
mcr_new |= PMCR_RX_FC_EN;
}
if (mcr_new != mcr_cur)
mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
}
......@@ -1534,7 +1506,7 @@ static void mt7530_phylink_mac_link_down(struct dsa_switch *ds, int port,
{
struct mt7530_priv *priv = ds->priv;
mt7530_port_set_status(priv, port, 0);
mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
}
static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
......@@ -1545,8 +1517,27 @@ static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
bool tx_pause, bool rx_pause)
{
struct mt7530_priv *priv = ds->priv;
u32 mcr;
mcr = PMCR_RX_EN | PMCR_TX_EN | PMCR_FORCE_LNK;
switch (speed) {
case SPEED_1000:
mcr |= PMCR_FORCE_SPEED_1000;
break;
case SPEED_100:
mcr |= PMCR_FORCE_SPEED_100;
break;
}
if (duplex == DUPLEX_FULL) {
mcr |= PMCR_FORCE_FDX;
if (tx_pause)
mcr |= PMCR_TX_FC_EN;
if (rx_pause)
mcr |= PMCR_RX_FC_EN;
}
mt7530_port_set_status(priv, port, 1);
mt7530_set(priv, MT7530_PMCR_P(port), mcr);
}
static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
......
......@@ -206,6 +206,10 @@ enum mt7530_vlan_port_attr {
#define PMCR_FORCE_LNK BIT(0)
#define PMCR_SPEED_MASK (PMCR_FORCE_SPEED_100 | \
PMCR_FORCE_SPEED_1000)
#define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
PMCR_FORCE_FDX | PMCR_FORCE_LNK)
#define MT7530_PMSR_P(x) (0x3008 + (x) * 0x100)
#define PMSR_EEE1G BIT(7)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment