ASoC: Don't use write sequencer to power up WM8903

The write sequencer sequencer sequence takes longer than is desirable
as it brings up a full playback path which is not required at this
point. Open coding the sequence cuts the startup time by two thirds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

sound/soc/codecs/wm8903.c

@@ -297,15 +297,6 @@ static int wm8903_run_sequence(struct snd_soc_codec *codec, unsigned int start)
 	return 0;
 }
 
-static void wm8903_sync_reg_cache(struct snd_soc_codec *codec, u16 *cache)
-{
-	int i;
-
-	/* There really ought to be something better we can do here :/ */
-	for (i = 0; i < ARRAY_SIZE(wm8903_reg_defaults); i++)
-		cache[i] = codec->hw_read(codec, i);
-}
-
 static void wm8903_reset(struct snd_soc_codec *codec)
 {
 	snd_soc_write(codec, WM8903_SW_RESET_AND_ID, 0);
@@ -1142,6 +1133,7 @@ static int wm8903_set_bias_level(struct snd_soc_codec *codec,
 	switch (level) {
 	case SND_SOC_BIAS_ON:
 		break;
+
 	case SND_SOC_BIAS_PREPARE:
 		snd_soc_update_bits(codec, WM8903_VMID_CONTROL_0,
 				    WM8903_VMID_RES_MASK,
@@ -1150,16 +1142,59 @@ static int wm8903_set_bias_level(struct snd_soc_codec *codec,
 
 	case SND_SOC_BIAS_STANDBY:
 		if (codec->dapm.bias_level == SND_SOC_BIAS_OFF) {
-			snd_soc_write(codec, WM8903_CLOCK_RATES_2,
-				     WM8903_CLK_SYS_ENA);
-
-			/* Change DC servo dither level in startup sequence */
-			snd_soc_write(codec, WM8903_WRITE_SEQUENCER_0, 0x11);
-			snd_soc_write(codec, WM8903_WRITE_SEQUENCER_1, 0x1257);
-			snd_soc_write(codec, WM8903_WRITE_SEQUENCER_2, 0x2);
-
-			wm8903_run_sequence(codec, 0);
-			wm8903_sync_reg_cache(codec, codec->reg_cache);
+			snd_soc_update_bits(codec, WM8903_BIAS_CONTROL_0,
+					    WM8903_POBCTRL | WM8903_ISEL_MASK |
+					    WM8903_STARTUP_BIAS_ENA |
+					    WM8903_BIAS_ENA,
+					    WM8903_POBCTRL |
+					    (2 << WM8903_ISEL_SHIFT) |
+					    WM8903_STARTUP_BIAS_ENA);
+
+			snd_soc_update_bits(codec,
+					    WM8903_ANALOGUE_SPK_OUTPUT_CONTROL_0,
+					    WM8903_SPK_DISCHARGE,
+					    WM8903_SPK_DISCHARGE);
+
+			msleep(33);
+
+			snd_soc_update_bits(codec, WM8903_POWER_MANAGEMENT_5,
+					    WM8903_SPKL_ENA | WM8903_SPKR_ENA,
+					    WM8903_SPKL_ENA | WM8903_SPKR_ENA);
+
+			snd_soc_update_bits(codec,
+					    WM8903_ANALOGUE_SPK_OUTPUT_CONTROL_0,
+					    WM8903_SPK_DISCHARGE, 0);
+
+			snd_soc_update_bits(codec, WM8903_VMID_CONTROL_0,
+					    WM8903_VMID_TIE_ENA |
+					    WM8903_BUFIO_ENA |
+					    WM8903_VMID_IO_ENA |
+					    WM8903_VMID_SOFT_MASK |
+					    WM8903_VMID_RES_MASK |
+					    WM8903_VMID_BUF_ENA,
+					    WM8903_VMID_TIE_ENA |
+					    WM8903_BUFIO_ENA |
+					    WM8903_VMID_IO_ENA |
+					    (2 << WM8903_VMID_SOFT_SHIFT) |
+					    WM8903_VMID_RES_250K |
+					    WM8903_VMID_BUF_ENA);
+
+			msleep(129);
+
+			snd_soc_update_bits(codec, WM8903_POWER_MANAGEMENT_5,
+					    WM8903_SPKL_ENA | WM8903_SPKR_ENA,
+					    0);
+
+			snd_soc_update_bits(codec, WM8903_VMID_CONTROL_0,
+					    WM8903_VMID_SOFT_MASK, 0);
+
+			snd_soc_update_bits(codec, WM8903_VMID_CONTROL_0,
+					    WM8903_VMID_RES_MASK,
+					    WM8903_VMID_RES_50K);
+
+			snd_soc_update_bits(codec, WM8903_BIAS_CONTROL_0,
+					    WM8903_BIAS_ENA | WM8903_POBCTRL,
+					    WM8903_BIAS_ENA);
 
 			/* By default no bypass paths are enabled so
 			 * enable Class W support.