Skip to content

L
linux
Commit 25075146 authored by Arnd Bergmann's avatar Arnd Bergmann
Browse files
Options

Merge tag 'qcom-arm64-for-4.15' of... 

Merge tag 'qcom-arm64-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/soc

Pull "Qualcomm ARM64 Updates for v4.15" from Andy Gross:

* Add PCIE support to relevant MSM8996 based boards
* Add RPM clock controller node on MSM8996
* Add dload address on MSM8916 and MSM8996
* Add MBHC button support on APQ8016 SBC
* Add RTMFS specific compatible for rmtfs memory node
* Fixups for MSM8916 GPIO line names and MDP address length

* tag 'qcom-arm64-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  arm64: dts: msm8916: Mark rmtfs node as qcom, rmtfs-mem compatible
  arm64: dts: msm8996: Add the rpm clock controller node
  arm64: dts: qcom: sbc: Name GPIO lines
  arm64: dts: qcom: msm8916: Shrink mdp address length for msm8916
  arm64: dts: apq8016-sbc: add mbhc buttons support
  arm64: dts: qcom: Specify dload address for msm8916 and msm8996
  arm64: dts: apq8096-db820c: never disable regulator on LS expansion
  arm64: dts: apq8096-db820c: Enable on board 3 pcie root complex
  arm64: dts: qcom: msm8996: add support to pcie
parents c94c8139 8cd00d5a
Show whitespace changes
Inline Side-by-side
Showing with 573 additions and 1 deletion
arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
View file @ 25075146
......@@ -19,6 +19,30 @@
#include <dt-bindings/input/input.h>
#include <dt-bindings/sound/apq8016-lpass.h>
/*
* GPIO name legend: proper name = the GPIO line is used as GPIO
* NC = not connected (pin out but not routed from the chip to
* anything the board)
* "[PER]" = pin is muxed for [peripheral] (not GPIO)
* LSEC = Low Speed External Connector
* HSEC = High Speed External Connector
*
* Line names are taken from the schematic "DragonBoard410c"
* dated monday, august 31, 2015. Page 5 in particular.
*
* For the lines routed to the external connectors the
* lines are named after the 96Boards CE Specification 1.0,
* Appendix "Expansion Connector Signal Description".
*
* When the 96Board naming of a line and the schematic name of
* the same line are in conflict, the 96Board specification
* takes precedence, which means that the external UART on the
* LSEC is named UART0 while the schematic and SoC names this
* UART3. This is only for the informational lines i.e. "[FOO]",
* the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
* ones actually used for GPIO.
*/
/ {
aliases {
serial0 = &blsp1_uart2;
......@@ -47,6 +71,132 @@ ramoops@bff00000{
};
soc {
pinctrl@1000000 {
gpio-line-names =
"[UART0_TX]", /* GPIO_0, LSEC pin 5 */
"[UART0_RX]", /* GPIO_1, LSEC pin 7 */
"[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
"[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
"[UART1_TX]", /* GPIO_4, LSEC pin 11 */
"[UART1_RX]", /* GPIO_5, LSEC pin 13 */
"[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
"[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
"[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
"[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
"[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
"[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
"GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
"GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
"[I2C3_SDA]", /* HSEC pin 38 */
"[I2C3_SCL]", /* HSEC pin 36 */
"[SPI0_MOSI]", /* LSEC pin 14 */
"[SPI0_MISO]", /* LSEC pin 10 */
"[SPI0_CS_N]", /* LSEC pin 12 */
"[SPI0_CLK]", /* LSEC pin 8 */
"HDMI_HPD_N", /* GPIO 20 */
"USR_LED_1_CTRL",
"[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
"[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
"GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
"GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
"[CSI0_MCLK]", /* HSEC pin 15 */
"[CSI1_MCLK]", /* HSEC pin 17 */
"GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
"[I2C2_SDA]", /* HSEC pin 34 */
"[I2C2_SCL]", /* HSEC pin 32 */
"DSI2HDMI_INT_N",
"DSI_SW_SEL_APQ",
"GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
"GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
"GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
"GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
"FORCED_USB_BOOT",
"SD_CARD_DET_N",
"[WCSS_BT_SSBI]",
"[WCSS_WLAN_DATA_2]", /* GPIO 40 */
"[WCSS_WLAN_DATA_1]",
"[WCSS_WLAN_DATA_0]",
"[WCSS_WLAN_SET]",
"[WCSS_WLAN_CLK]",
"[WCSS_FM_SSBI]",
"[WCSS_FM_SDI]",
"[WCSS_BT_DAT_CTL]",
"[WCSS_BT_DAT_STB]",
"NC",
"NC", /* GPIO 50 */
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC", /* GPIO 60 */
"NC",
"NC",
"[CDC_PDM0_CLK]",
"[CDC_PDM0_SYNC]",
"[CDC_PDM0_TX0]",
"[CDC_PDM0_RX0]",
"[CDC_PDM0_RX1]",
"[CDC_PDM0_RX2]",
"GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
"NC", /* GPIO 70 */
"NC",
"NC",
"NC",
"NC", /* GPIO 74 */
"NC",
"NC",
"NC",
"NC",
"NC",
"BOOT_CONFIG_0", /* GPIO 80 */
"BOOT_CONFIG_1",
"BOOT_CONFIG_2",
"BOOT_CONFIG_3",
"NC",
"NC",
"BOOT_CONFIG_5",
"NC",
"NC",
"NC",
"NC", /* GPIO 90 */
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC", /* GPIO 100 */
"NC",
"NC",
"NC",
"SSBI_GPS",
"NC",
"NC",
"KEY_VOLP_N",
"NC",
"NC",
"[LS_EXP_MI2S_WS]", /* GPIO 110 */
"NC",
"NC",
"[LS_EXP_MI2S_SCK]",
"[LS_EXP_MI2S_DATA0]",
"GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
"NC",
"[DSI2HDMI_MI2S_WS]",
"[DSI2HDMI_MI2S_SCK]",
"[DSI2HDMI_MI2S_DATA0]",
"USR_LED_2_CTRL", /* GPIO 120 */
"SB_HS_ID";
};
dma@7884000 {
status = "okay";
};
......@@ -329,6 +479,25 @@ codec {
};
};
spmi@200f000 {
pm8916@0 {
gpios@c000 {
gpio-line-names =
"USR_LED_3_CTRL",
"USR_LED_4_CTRL",
"USB_HUB_RESET_N_PM",
"USB_SW_SEL_PM";
};
mpps@a000 {
gpio-line-names =
"VDD_PX_BIAS",
"WLAN_LED_CTRL",
"BT_LED_CTRL",
"GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
};
};
};
wcnss@a21b000 {
status = "okay";
};
......@@ -379,6 +548,8 @@ &wcd_codec {
status = "okay";
clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
clock-names = "mclk";
qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
};
&smd_rpm_regulators {
......
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
View file @ 25075146
......@@ -138,6 +138,22 @@ usb2_id: usb2-id {
pinctrl-names = "default";
pinctrl-0 = <&usb2_vbus_det_gpio>;
};
agnoc@0 {
qcom,pcie@00600000 {
perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
};
qcom,pcie@00608000 {
status = "okay";
perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
};
qcom,pcie@00610000 {
status = "okay";
perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
};
};
};
......@@ -173,9 +189,15 @@ s3 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
};
/**
* 1.8v required on LS expansion
* for mezzanine boards
*/
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
s5 {
regulator-min-microvolt = <2150000>;
......
arch/arm64/boot/dts/qcom/msm8916.dtsi
View file @ 25075146
......@@ -69,8 +69,11 @@ reserved@8668000 {
};
rmtfs@86700000 {
compatible = "qcom,rmtfs-mem";
reg = <0x0 0x86700000 0x0 0xe0000>;
no-map;
qcom,client-id = <1>;
};
rfsa@867e00000 {
......@@ -257,6 +260,8 @@ scm: scm {
clocks = <&gcc GCC_CRYPTO_CLK>, <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>;
clock-names = "core", "bus", "iface";
#reset-cells = <1>;
qcom,dload-mode = <&tcsr 0x6100>;
};
};
......@@ -814,7 +819,7 @@ mdss: mdss@1a00000 {
mdp: mdp@1a01000 {
compatible = "qcom,mdp5";
reg = <0x1a01000 0x90000>;
reg = <0x1a01000 0x89000>;
reg-names = "mdp_phys";
interrupt-parent = <&mdss>;
......
arch/arm64/boot/dts/qcom/msm8996-pins.dtsi
View file @ 25075146
......@@ -300,4 +300,199 @@ config {
drive-strength = <2>; /* 2 MA */
};
};
pcie0_clkreq_default: pcie0_clkreq_default {
mux {
pins = "gpio36";
function = "pci_e0";
};
config {
pins = "gpio36";
drive-strength = <2>;
bias-pull-up;
};
};
pcie0_perst_default: pcie0_perst_default {
mux {
pins = "gpio35";
function = "gpio";
};
config {
pins = "gpio35";
drive-strength = <2>;
bias-pull-down;
};
};
pcie0_wake_default: pcie0_wake_default {
mux {
pins = "gpio37";
function = "gpio";
};
config {
pins = "gpio37";
drive-strength = <2>;
bias-pull-up;
};
};
pcie0_clkreq_sleep: pcie0_clkreq_sleep {
mux {
pins = "gpio36";
function = "gpio";
};
config {
pins = "gpio36";
drive-strength = <2>;
bias-disable;
};
};
pcie0_wake_sleep: pcie0_wake_sleep {
mux {
pins = "gpio37";
function = "gpio";
};
config {
pins = "gpio37";
drive-strength = <2>;
bias-disable;
};
};
pcie1_clkreq_default: pcie1_clkreq_default {
mux {
pins = "gpio131";
function = "pci_e1";
};
config {
pins = "gpio131";
drive-strength = <2>;
bias-pull-up;
};
};
pcie1_perst_default: pcie1_perst_default {
mux {
pins = "gpio130";
function = "gpio";
};
config {
pins = "gpio130";
drive-strength = <2>;
bias-pull-down;
};
};
pcie1_wake_default: pcie1_wake_default {
mux {
pins = "gpio132";
function = "gpio";
};
config {
pins = "gpio132";
drive-strength = <2>;
bias-pull-down;
};
};
pcie1_clkreq_sleep: pcie1_clkreq_sleep {
mux {
pins = "gpio131";
function = "gpio";
};
config {
pins = "gpio131";
drive-strength = <2>;
bias-disable;
};
};
pcie1_wake_sleep: pcie1_wake_sleep {
mux {
pins = "gpio132";
function = "gpio";
};
config {
pins = "gpio132";
drive-strength = <2>;
bias-disable;
};
};
pcie2_clkreq_default: pcie2_clkreq_default {
mux {
pins = "gpio115";
function = "pci_e2";
};
config {
pins = "gpio115";
drive-strength = <2>;
bias-pull-up;
};
};
pcie2_perst_default: pcie2_perst_default {
mux {
pins = "gpio114";
function = "gpio";
};
config {
pins = "gpio114";
drive-strength = <2>;
bias-pull-down;
};
};
pcie2_wake_default: pcie2_wake_default {
mux {
pins = "gpio116";
function = "gpio";
};
config {
pins = "gpio116";
drive-strength = <2>;
bias-pull-down;
};
};
pcie2_clkreq_sleep: pcie2_clkreq_sleep {
mux {
pins = "gpio115";
function = "gpio";
};
config {
pins = "gpio115";
drive-strength = <2>;
bias-disable;
};
};
pcie2_wake_sleep: pcie2_wake_sleep {
mux {
pins = "gpio116";
function = "gpio";
};
config {
pins = "gpio116";
drive-strength = <2>;
bias-disable;
};
};
};
arch/arm64/boot/dts/qcom/msm8996.dtsi
View file @ 25075146
......@@ -13,6 +13,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8996.h>
#include <dt-bindings/clock/qcom,mmcc-msm8996.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
/ {
model = "Qualcomm Technologies, Inc. MSM8996";
......@@ -261,6 +262,8 @@ psci {
firmware {
scm {
compatible = "qcom,scm-msm8996";
qcom,dload-mode = <&tcsr 0x13000>;
};
};
......@@ -289,6 +292,11 @@ rpm_requests {
compatible = "qcom,rpm-msm8996";
qcom,glink-channels = "rpm_requests";
rpmcc: qcom,rpmcc {
compatible = "qcom,rpmcc-msm8996";
#clock-cells = <1>;
};
pm8994-regulators {
compatible = "qcom,rpm-pm8994-regulators";
......@@ -358,6 +366,11 @@ tcsr_mutex_regs: syscon@740000 {
reg = <0x740000 0x20000>;
};
tcsr: syscon@7a0000 {
compatible = "qcom,tcsr-msm8996", "syscon";
reg = <0x7a0000 0x18000>;
};
intc: interrupt-controller@9bc0000 {
compatible = "arm,gic-v3";
#interrupt-cells = <3>;
......@@ -819,6 +832,172 @@ dwc3@6a00000 {
phy-names = "usb2-phy", "usb3-phy";
};
};
agnoc@0 {
power-domains = <&gcc AGGRE0_NOC_GDSC>;
compatible = "simple-pm-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
pcie0: qcom,pcie@00600000 {
compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
status = "disabled";
power-domains = <&gcc PCIE0_GDSC>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
reg = <0x00600000 0x2000>,
<0x0c000000 0xf1d>,
<0x0c000f20 0xa8>,
<0x0c100000 0x100000>;
reg-names = "parf", "dbi", "elbi","config";
phys = <&pciephy_0>;
phy-names = "pciephy";
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x01000000 0x0 0x0c200000 0x0c200000 0x0 0x100000>,
<0x02000000 0x0 0x0c300000 0x0c300000 0x0 0xd00000>;
interrupts = <GIC_SPI 405 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 244 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 245 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 247 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 248 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
pinctrl-names = "default", "sleep";
pinctrl-0 = <&pcie0_clkreq_default &pcie0_perst_default &pcie0_wake_default>;
pinctrl-1 = <&pcie0_clkreq_sleep &pcie0_perst_default &pcie0_wake_sleep>;
vdda-supply = <&pm8994_l28>;
linux,pci-domain = <0>;
clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
<&gcc GCC_PCIE_0_AUX_CLK>,
<&gcc GCC_PCIE_0_CFG_AHB_CLK>,
<&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
<&gcc GCC_PCIE_0_SLV_AXI_CLK>;
clock-names = "pipe",
"aux",
"cfg",
"bus_master",
"bus_slave";
};
pcie1: qcom,pcie@00608000 {
compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
power-domains = <&gcc PCIE1_GDSC>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
status = "disabled";
reg = <0x00608000 0x2000>,
<0x0d000000 0xf1d>,
<0x0d000f20 0xa8>,
<0x0d100000 0x100000>;
reg-names = "parf", "dbi", "elbi","config";
phys = <&pciephy_1>;
phy-names = "pciephy";
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>,
<0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>;
interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
pinctrl-names = "default", "sleep";
pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>;
pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>;
vdda-supply = <&pm8994_l28>;
linux,pci-domain = <1>;
clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
<&gcc GCC_PCIE_1_AUX_CLK>,
<&gcc GCC_PCIE_1_CFG_AHB_CLK>,
<&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
<&gcc GCC_PCIE_1_SLV_AXI_CLK>;
clock-names = "pipe",
"aux",
"cfg",
"bus_master",
"bus_slave";
};
pcie2: qcom,pcie@00610000 {
compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
power-domains = <&gcc PCIE2_GDSC>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
status = "disabled";
reg = <0x00610000 0x2000>,
<0x0e000000 0xf1d>,
<0x0e000f20 0xa8>,
<0x0e100000 0x100000>;
reg-names = "parf", "dbi", "elbi","config";
phys = <&pciephy_2>;
phy-names = "pciephy";
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x01000000 0x0 0x0e200000 0x0e200000 0x0 0x100000>,
<0x02000000 0x0 0x0e300000 0x0e300000 0x0 0x1d00000>;
device_type = "pci";
interrupts = <GIC_SPI 421 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
pinctrl-names = "default", "sleep";
pinctrl-0 = <&pcie2_clkreq_default &pcie2_perst_default &pcie2_wake_default>;
pinctrl-1 = <&pcie2_clkreq_sleep &pcie2_perst_default &pcie2_wake_sleep >;
vdda-supply = <&pm8994_l28>;
linux,pci-domain = <2>;
clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
<&gcc GCC_PCIE_2_AUX_CLK>,
<&gcc GCC_PCIE_2_CFG_AHB_CLK>,
<&gcc GCC_PCIE_2_MSTR_AXI_CLK>,
<&gcc GCC_PCIE_2_SLV_AXI_CLK>;
clock-names = "pipe",
"aux",
"cfg",
"bus_master",
"bus_slave";
};
};
};
adsp-pil {
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7