hpsa: rework controller command submission

Allow driver initiated commands to have a timeout.  It does not
yet try to do anything with timeouts on such commands.

We are sending a reset in order to get rid of a command we want to abort.
If we make it return on the same reply queue as the command we want to abort,
the completion of the aborted command will not race with the completion of
the reset command.

Rename hpsa_scsi_do_simple_cmd_core() to hpsa_scsi_do_simple_cmd(), since
this function is the interface for issuing commands to the controller and
not the "core" of that implementation.  Add a parameter to it which allows
the caller to specify the reply queue to be used.  Modify existing callers
to specify the default reply queue.

Rename __hpsa_scsi_do_simple_cmd_core() to hpsa_scsi_do_simple_cmd_core(),
since this routine is the "core" implementation of the "do simple command"
function and there is no longer any other function with a similar name.
Modify the existing callers of this routine (other than
hpsa_scsi_do_simple_cmd()) to instead call hpsa_scsi_do_simple_cmd(), since
it will now accept the reply_queue paramenter, and it provides a controller
lock-up check.  (Also, tweak two related message strings to make them
distinct from each other.)

Submitting a command to a locked up controller always results in a timeout,
so check for controller lock-up before submitting.

This is to enable fixing a race between command completions and
abort completions on different reply queues in a subsequent patch.
We want to be able to specify which reply queue an abort completion
should occur on so that it cannot race the completion of the command
it is trying to abort.

The following race was possible in theory:

  1. Abort command is sent to hardware.
  2. Command to be aborted simultaneously completes on another
     reply queue.
  3. Hardware receives abort command, decides command has already
     completed and indicates this to the driver via another different
     reply queue.
  4. driver processes abort completion finds that the hardware does not know
     about the command, concludes that therefore the command cannot complete,
     returns SUCCESS indicating to the mid-layer that the scsi_cmnd may be
     re-used.
  5. Command from step 2 is processed and completed back to scsi mid
     layer (after we already promised that would never happen.)

Fix by forcing aborts to complete on the same reply queue as the command
they are aborting.

Piggybacking device rescanning functionality onto the lockup
detection thread is not a good idea because if the controller
locks up during device rescanning, then the thread could get
stuck, then the lockup isn't detected.  Use separate work
queues for device rescanning and lockup detection.

Detect controller lockup in abort handler.

After a lockup is detected, return DO_NO_CONNECT which results in immediate
termination of commands rather than DID_ERR which results in retries.

Modify detect_controller_lockup() to return the result, to remove the need for
a separate check.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

drivers/scsi/hpsa_cmd.h

@@ -43,6 +43,11 @@
 #define CMD_TIMEOUT             0x000B
 #define CMD_UNABORTABLE		0x000C
 #define CMD_IOACCEL_DISABLED	0x000E
+#define CMD_CTLR_LOCKUP		0xffff
+/* Note: CMD_CTLR_LOCKUP is not a value defined by the CISS spec
+ * it is a value defined by the driver that commands can be marked
+ * with when a controller lockup has been detected by the driver
+ */
 
 
 /* Unit Attentions ASC's as defined for the MSA2012sa */