Commit 2562756d authored by Masaki Ota's avatar Masaki Ota Committed by Jiri Kosina

HID: add Alps I2C HID Touchpad-Stick support

Add support Alps I2C HID Touchpad and Stick device.
Signed-off-by: default avatarMasaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: default avatarJiri Kosina <jkosina@suse.cz>
parent dcc4c2f6
ALPS HID Touchpad Protocol
----------------------
Introduction
------------
Currently ALPS HID driver supports U1 Touchpad device.
U1 devuce basic information.
Vender ID 0x044E
Product ID 0x120B
Version ID 0x0121
HID Descriptor
------------
Byte Field Value Notes
0 wHIDDescLength 001E Length of HID Descriptor : 30 bytes
2 bcdVersion 0100 Compliant with Version 1.00
4 wReportDescLength 00B2 Report Descriptor is 178 Bytes (0x00B2)
6 wReportDescRegister 0002 Identifier to read Report Descriptor
8 wInputRegister 0003 Identifier to read Input Report
10 wMaxInputLength 0053 Input Report is 80 Bytes + 2
12 wOutputRegister 0000 Identifier to read Output Report
14 wMaxOutputLength 0000 No Output Reports
16 wCommandRegister 0005 Identifier for Command Register
18 wDataRegister 0006 Identifier for Data Register
20 wVendorID 044E Vendor ID 0x044E
22 wProductID 120B Product ID 0x120B
24 wVersionID 0121 Version 01.21
26 RESERVED 0000 RESERVED
Report ID
------------
ReportID-1 (Input Reports) (HIDUsage-Mouse) for TP&SP
ReportID-2 (Input Reports) (HIDUsage-keyboard) for TP
ReportID-3 (Input Reports) (Vendor Usage: Max 10 finger data) for TP
ReportID-4 (Input Reports) (Vendor Usage: ON bit data) for GP
ReportID-5 (Feature Reports) Feature Reports
ReportID-6 (Input Reports) (Vendor Usage: StickPointer data) for SP
ReportID-7 (Feature Reports) Flash update (Bootloader)
Data pattern
------------
Case1 ReportID_1 TP/SP Relative/Relative
Case2 ReportID_3 TP Absolute
ReportID_6 SP Absolute
Command Read/Write
------------------
To read/write to RAM, need to send a commands to the device.
The command format is as below.
DataByte(SET_REPORT)
Byte1 Command Byte
Byte2 Address - Byte 0 (LSB)
Byte3 Address - Byte 1
Byte4 Address - Byte 2
Byte5 Address - Byte 3 (MSB)
Byte6 Value Byte
Byte7 Checksum
Command Byte is read=0xD1/write=0xD2 .
Address is read/write RAM address.
Value Byte is writing data when you send the write commands.
When you read RAM, there is no meaning.
DataByte(GET_REPORT)
Byte1 Response Byte
Byte2 Address - Byte 0 (LSB)
Byte3 Address - Byte 1
Byte4 Address - Byte 2
Byte5 Address - Byte 3 (MSB)
Byte6 Value Byte
Byte7 Checksum
Read value is stored in Value Byte.
Packet Format
Touchpad data byte
------------------
b7 b6 b5 b4 b3 b2 b1 b0
1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
2 0 0 0 Fcv Fn3 Fn2 Fn1 Fn0
3 Xa0_7 Xa0_6 Xa0_5 Xa0_4 Xa0_3 Xa0_2 Xa0_1 Xa0_0
4 Xa0_15 Xa0_14 Xa0_13 Xa0_12 Xa0_11 Xa0_10 Xa0_9 Xa0_8
5 Ya0_7 Ya0_6 Ya0_5 Ya0_4 Ya0_3 Ya0_2 Ya0_1 Ya0_0
6 Ya0_15 Ya0_14 Ya0_13 Ya0_12 Ya0_11 Ya0_10 Ya0_9 Ya0_8
7 LFB0 Zs0_6 Zs0_5 Zs0_4 Zs0_3 Zs0_2 Zs0_1 Zs0_0
8 Xa1_7 Xa1_6 Xa1_5 Xa1_4 Xa1_3 Xa1_2 Xa1_1 Xa1_0
9 Xa1_15 Xa1_14 Xa1_13 Xa1_12 Xa1_11 Xa1_10 Xa1_9 Xa1_8
10 Ya1_7 Ya1_6 Ya1_5 Ya1_4 Ya1_3 Ya1_2 Ya1_1 Ya1_0
11 Ya1_15 Ya1_14 Ya1_13 Ya1_12 Ya1_11 Ya1_10 Ya1_9 Ya1_8
12 LFB1 Zs1_6 Zs1_5 Zs1_4 Zs1_3 Zs1_2 Zs1_1 Zs1_0
13 Xa2_7 Xa2_6 Xa2_5 Xa2_4 Xa2_3 Xa2_2 Xa2_1 Xa2_0
14 Xa2_15 Xa2_14 Xa2_13 Xa2_12 Xa2_11 Xa2_10 Xa2_9 Xa2_8
15 Ya2_7 Ya2_6 Ya2_5 Ya2_4 Ya2_3 Ya2_2 Ya2_1 Ya2_0
16 Ya2_15 Ya2_14 Ya2_13 Ya2_12 Ya2_11 Ya2_10 Ya2_9 Ya2_8
17 LFB2 Zs2_6 Zs2_5 Zs2_4 Zs2_3 Zs2_2 Zs2_1 Zs2_0
18 Xa3_7 Xa3_6 Xa3_5 Xa3_4 Xa3_3 Xa3_2 Xa3_1 Xa3_0
19 Xa3_15 Xa3_14 Xa3_13 Xa3_12 Xa3_11 Xa3_10 Xa3_9 Xa3_8
20 Ya3_7 Ya3_6 Ya3_5 Ya3_4 Ya3_3 Ya3_2 Ya3_1 Ya3_0
21 Ya3_15 Ya3_14 Ya3_13 Ya3_12 Ya3_11 Ya3_10 Ya3_9 Ya3_8
22 LFB3 Zs3_6 Zs3_5 Zs3_4 Zs3_3 Zs3_2 Zs3_1 Zs3_0
23 Xa4_7 Xa4_6 Xa4_5 Xa4_4 Xa4_3 Xa4_2 Xa4_1 Xa4_0
24 Xa4_15 Xa4_14 Xa4_13 Xa4_12 Xa4_11 Xa4_10 Xa4_9 Xa4_8
25 Ya4_7 Ya4_6 Ya4_5 Ya4_4 Ya4_3 Ya4_2 Ya4_1 Ya4_0
26 Ya4_15 Ya4_14 Ya4_13 Ya4_12 Ya4_11 Ya4_10 Ya4_9 Ya4_8
27 LFB4 Zs4_6 Zs4_5 Zs4_4 Zs4_3 Zs4_2 Zs4_1 Zs4_0
SW1-SW6: SW ON/OFF status
Xan_15-0(16bit):X Absolute data of the "n"th finger
Yan_15-0(16bit):Y Absolute data of the "n"th finger
Zsn_6-0(7bit): Operation area of the "n"th finger
StickPointer data byte
------------------
b7 b6 b5 b4 b3 b2 b1 b0
Byte1 1 1 1 0 1 SW3 SW2 SW1
Byte2 X7 X6 X5 X4 X3 X2 X1 X0
Byte3 X15 X14 X13 X12 X11 X10 X9 X8
Byte4 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
Byte5 Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8
Byte6 Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0
Byte7 T&P Z14 Z13 Z12 Z11 Z10 Z9 Z8
SW1-SW3: SW ON/OFF status
Xn_15-0(16bit):X Absolute data
Yn_15-0(16bit):Y Absolute data
Zn_14-0(15bit):Z
...@@ -936,6 +936,14 @@ config HID_SENSOR_CUSTOM_SENSOR ...@@ -936,6 +936,14 @@ config HID_SENSOR_CUSTOM_SENSOR
standard sensors. standard sensors.
Select this config option for custom/generic sensor support. Select this config option for custom/generic sensor support.
config HID_ALPS
tristate "Alps HID device support"
depends on HID
---help---
Support for Alps I2C HID touchpads and StickPointer.
Say Y here if you have a Alps touchpads over i2c-hid or usbhid
and want support for its special functionalities.
endmenu endmenu
endif # HID endif # HID
......
...@@ -21,6 +21,7 @@ hid-wiimote-y := hid-wiimote-core.o hid-wiimote-modules.o ...@@ -21,6 +21,7 @@ hid-wiimote-y := hid-wiimote-core.o hid-wiimote-modules.o
hid-wiimote-$(CONFIG_DEBUG_FS) += hid-wiimote-debug.o hid-wiimote-$(CONFIG_DEBUG_FS) += hid-wiimote-debug.o
obj-$(CONFIG_HID_A4TECH) += hid-a4tech.o obj-$(CONFIG_HID_A4TECH) += hid-a4tech.o
obj-$(CONFIG_HID_ALPS) += hid-alps.o
obj-$(CONFIG_HID_ACRUX) += hid-axff.o obj-$(CONFIG_HID_ACRUX) += hid-axff.o
obj-$(CONFIG_HID_APPLE) += hid-apple.o obj-$(CONFIG_HID_APPLE) += hid-apple.o
obj-$(CONFIG_HID_APPLEIR) += hid-appleir.o obj-$(CONFIG_HID_APPLEIR) += hid-appleir.o
......
/*
* Copyright (c) 2016 Masaki Ota <masaki.ota@jp.alps.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
* Software Foundation; either version 2 of the License, or (at your option)
* any later version.
*/
#include <linux/kernel.h>
#include <linux/hid.h>
#include <linux/input.h>
#include <linux/input/mt.h>
#include <linux/module.h>
#include <asm/unaligned.h>
#include "hid-ids.h"
/* ALPS Device Product ID */
#define HID_PRODUCT_ID_T3_BTNLESS 0xD0C0
#define HID_PRODUCT_ID_COSMO 0x1202
#define HID_PRODUCT_ID_U1_PTP_1 0x1207
#define HID_PRODUCT_ID_U1 0x1209
#define HID_PRODUCT_ID_U1_PTP_2 0x120A
#define HID_PRODUCT_ID_U1_DUAL 0x120B
#define HID_PRODUCT_ID_T4_BTNLESS 0x120C
#define DEV_SINGLEPOINT 0x01
#define DEV_DUALPOINT 0x02
#define U1_MOUSE_REPORT_ID 0x01 /* Mouse data ReportID */
#define U1_ABSOLUTE_REPORT_ID 0x03 /* Absolute data ReportID */
#define U1_FEATURE_REPORT_ID 0x05 /* Feature ReportID */
#define U1_SP_ABSOLUTE_REPORT_ID 0x06 /* Feature ReportID */
#define U1_FEATURE_REPORT_LEN 0x08 /* Feature Report Length */
#define U1_FEATURE_REPORT_LEN_ALL 0x0A
#define U1_CMD_REGISTER_READ 0xD1
#define U1_CMD_REGISTER_WRITE 0xD2
#define U1_DEVTYPE_SP_SUPPORT 0x10 /* SP Support */
#define U1_DISABLE_DEV 0x01
#define U1_TP_ABS_MODE 0x02
#define U1_SP_ABS_MODE 0x80
#define ADDRESS_U1_DEV_CTRL_1 0x00800040
#define ADDRESS_U1_DEVICE_TYP 0x00800043
#define ADDRESS_U1_NUM_SENS_X 0x00800047
#define ADDRESS_U1_NUM_SENS_Y 0x00800048
#define ADDRESS_U1_PITCH_SENS_X 0x00800049
#define ADDRESS_U1_PITCH_SENS_Y 0x0080004A
#define ADDRESS_U1_RESO_DWN_ABS 0x0080004E
#define ADDRESS_U1_PAD_BTN 0x00800052
#define ADDRESS_U1_SP_BTN 0x0080009F
#define MAX_TOUCHES 5
/**
* struct u1_data
*
* @input: pointer to the kernel input device
* @input2: pointer to the kernel input2 device
* @hdev: pointer to the struct hid_device
*
* @dev_ctrl: device control parameter
* @dev_type: device type
* @sen_line_num_x: number of sensor line of X
* @sen_line_num_y: number of sensor line of Y
* @pitch_x: sensor pitch of X
* @pitch_y: sensor pitch of Y
* @resolution: resolution
* @btn_info: button information
* @x_active_len_mm: active area length of X (mm)
* @y_active_len_mm: active area length of Y (mm)
* @x_max: maximum x coordinate value
* @y_max: maximum y coordinate value
* @btn_cnt: number of buttons
* @sp_btn_cnt: number of stick buttons
*/
struct u1_dev {
struct input_dev *input;
struct input_dev *input2;
struct hid_device *hdev;
u8 dev_ctrl;
u8 dev_type;
u8 sen_line_num_x;
u8 sen_line_num_y;
u8 pitch_x;
u8 pitch_y;
u8 resolution;
u8 btn_info;
u8 sp_btn_info;
u32 x_active_len_mm;
u32 y_active_len_mm;
u32 x_max;
u32 y_max;
u32 btn_cnt;
u32 sp_btn_cnt;
};
struct u1_dev *priv;
static int u1_read_write_register(struct hid_device *hdev, u32 address,
u8 *read_val, u8 write_val, bool read_flag)
{
int ret, i;
u8 check_sum;
u8 *input;
u8 *readbuf;
input = kzalloc(sizeof(u8)*U1_FEATURE_REPORT_LEN, GFP_KERNEL);
if (!input)
return -ENOMEM;
readbuf = kzalloc(sizeof(u8)*U1_FEATURE_REPORT_LEN, GFP_KERNEL);
if (!readbuf) {
kfree(input);
return -ENOMEM;
}
input[0] = U1_FEATURE_REPORT_ID;
if (read_flag) {
input[1] = U1_CMD_REGISTER_READ;
input[6] = 0x00;
} else {
input[1] = U1_CMD_REGISTER_WRITE;
input[6] = write_val;
}
put_unaligned_le32(address, input + 2);
/* Calculate the checksum */
check_sum = U1_FEATURE_REPORT_LEN_ALL;
for (i = 0; i < U1_FEATURE_REPORT_LEN - 1; i++)
check_sum += input[i];
input[7] = check_sum;
ret = hid_hw_raw_request(hdev, U1_FEATURE_REPORT_ID, input,
sizeof(input), HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
if (ret < 0) {
dev_err(&hdev->dev, "failed to read command (%d)\n", ret);
goto exit;
}
if (read_flag) {
ret = hid_hw_raw_request(hdev, U1_FEATURE_REPORT_ID, readbuf,
sizeof(readbuf), HID_FEATURE_REPORT,
HID_REQ_GET_REPORT);
if (ret < 0) {
dev_err(&hdev->dev, "failed read register (%d)\n", ret);
goto exit;
}
*read_val = readbuf[6];
}
kfree(input);
kfree(readbuf);
return 0;
exit:
kfree(input);
kfree(readbuf);
return ret;
}
static int alps_raw_event(struct hid_device *hdev,
struct hid_report *report, u8 *data, int size)
{
int x[MAX_TOUCHES], y[MAX_TOUCHES], z[MAX_TOUCHES];
int i, left, right, middle;
short sp_x, sp_y, sp_z;
struct u1_dev *hdata = hid_get_drvdata(hdev);
switch (data[0]) {
case U1_MOUSE_REPORT_ID:
break;
case U1_FEATURE_REPORT_ID:
break;
case U1_ABSOLUTE_REPORT_ID:
for (i = 0; i < MAX_TOUCHES; i++) {
x[i] = (data[3+(5*i)] | (data[4+(5*i)] << 8));
y[i] = (data[5+(5*i)] | (data[6+(5*i)] << 8));
z[i] = data[7+(5*i)] & 0x7F;
left = data[1] & 0x1;
right = (data[1] & 0x2) >> 1;
middle = (data[1] & 0x4) >> 2;
input_mt_slot(hdata->input, i);
if (z[i] != 0) {
input_mt_report_slot_state(hdata->input,
MT_TOOL_FINGER, 1);
} else {
input_mt_report_slot_state(hdata->input,
MT_TOOL_FINGER, 0);
break;
}
input_event(hdata->input, EV_ABS,
ABS_MT_POSITION_X, x[i]);
input_event(hdata->input, EV_ABS,
ABS_MT_POSITION_Y, y[i]);
input_event(hdata->input, EV_ABS,
ABS_MT_PRESSURE, z[i]);
}
input_mt_sync_frame(hdata->input);
input_sync(hdata->input);
input_event(hdata->input, EV_KEY, BTN_LEFT, left);
input_event(hdata->input, EV_KEY, BTN_RIGHT, right);
input_event(hdata->input, EV_KEY, BTN_MIDDLE, middle);
return 1;
case U1_SP_ABSOLUTE_REPORT_ID:
sp_x = (data[2] | (data[3] << 8));
sp_y = (data[4] | (data[5] << 8));
sp_z = (data[6] | data[7]) & 0x7FFF;
left = data[1] & 0x1;
right = (data[1] & 0x2) >> 1;
middle = (data[1] & 0x4) >> 2;
sp_x = sp_x / 8;
sp_y = sp_y / 8;
input_event(priv->input2, EV_REL, REL_X, sp_x);
input_event(priv->input2, EV_REL, REL_Y, sp_y);
input_event(priv->input2, EV_KEY, BTN_LEFT, left);
input_event(priv->input2, EV_KEY, BTN_RIGHT, right);
input_event(priv->input2, EV_KEY, BTN_MIDDLE, middle);
input_sync(priv->input2);
return 1;
}
return 0;
}
#ifdef CONFIG_PM
static int alps_post_reset(struct hid_device *hdev)
{
return u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
NULL, U1_TP_ABS_MODE, false);
}
static int alps_post_resume(struct hid_device *hdev)
{
return u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
NULL, U1_TP_ABS_MODE, false);
}
#endif /* CONFIG_PM */
static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
{
struct u1_dev *data = hid_get_drvdata(hdev);
struct input_dev *input = hi->input, *input2;
struct u1_dev devInfo;
int ret;
int res_x, res_y, i;
/* Check device product ID */
switch (hdev->product) {
case HID_PRODUCT_ID_U1:
case HID_PRODUCT_ID_U1_DUAL:
break;
default:
return 0;
}
data->input = input;
hid_dbg(hdev, "Opening low level driver\n");
ret = hid_hw_open(hdev);
if (ret)
return ret;
/* Allow incoming hid reports */
hid_device_io_start(hdev);
/* Device initialization */
ret = u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
&devInfo.dev_ctrl, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_DEV_CTRL_1 (%d)\n", ret);
goto exit;
}
devInfo.dev_ctrl &= ~U1_DISABLE_DEV;
devInfo.dev_ctrl |= U1_TP_ABS_MODE;
ret = u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
NULL, devInfo.dev_ctrl, false);
if (ret < 0) {
dev_err(&hdev->dev, "failed to change TP mode (%d)\n", ret);
goto exit;
}
ret = u1_read_write_register(hdev, ADDRESS_U1_NUM_SENS_X,
&devInfo.sen_line_num_x, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_NUM_SENS_X (%d)\n", ret);
goto exit;
}
ret = u1_read_write_register(hdev, ADDRESS_U1_NUM_SENS_Y,
&devInfo.sen_line_num_y, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_NUM_SENS_Y (%d)\n", ret);
goto exit;
}
ret = u1_read_write_register(hdev, ADDRESS_U1_PITCH_SENS_X,
&devInfo.pitch_x, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_PITCH_SENS_X (%d)\n", ret);
goto exit;
}
ret = u1_read_write_register(hdev, ADDRESS_U1_PITCH_SENS_Y,
&devInfo.pitch_y, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_PITCH_SENS_Y (%d)\n", ret);
goto exit;
}
ret = u1_read_write_register(hdev, ADDRESS_U1_RESO_DWN_ABS,
&devInfo.resolution, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
goto exit;
}
ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
&devInfo.btn_info, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_PAD_BTN (%d)\n", ret);
goto exit;
}
/* Check StickPointer device */
ret = u1_read_write_register(hdev, ADDRESS_U1_DEVICE_TYP,
&devInfo.dev_type, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_DEVICE_TYP (%d)\n", ret);
goto exit;
}
devInfo.x_active_len_mm =
(devInfo.pitch_x * (devInfo.sen_line_num_x - 1)) / 10;
devInfo.y_active_len_mm =
(devInfo.pitch_y * (devInfo.sen_line_num_y - 1)) / 10;
devInfo.x_max =
(devInfo.resolution << 2) * (devInfo.sen_line_num_x - 1);
devInfo.y_max =
(devInfo.resolution << 2) * (devInfo.sen_line_num_y - 1);
__set_bit(EV_ABS, input->evbit);
input_set_abs_params(input, ABS_MT_POSITION_X, 1, devInfo.x_max, 0, 0);
input_set_abs_params(input, ABS_MT_POSITION_Y, 1, devInfo.y_max, 0, 0);
if (devInfo.x_active_len_mm && devInfo.y_active_len_mm) {
res_x = (devInfo.x_max - 1) / devInfo.x_active_len_mm;
res_y = (devInfo.y_max - 1) / devInfo.y_active_len_mm;
input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
}
input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0);
input_mt_init_slots(input, MAX_TOUCHES, INPUT_MT_POINTER);
__set_bit(EV_KEY, input->evbit);
if ((devInfo.btn_info & 0x0F) == (devInfo.btn_info & 0xF0) >> 4) {
devInfo.btn_cnt = (devInfo.btn_info & 0x0F);
} else {
/* Button pad */
devInfo.btn_cnt = 1;
__set_bit(INPUT_PROP_BUTTONPAD, input->propbit);
}
for (i = 0; i < devInfo.btn_cnt; i++)
__set_bit(BTN_LEFT + i, input->keybit);
/* Stick device initialization */
if (devInfo.dev_type & U1_DEVTYPE_SP_SUPPORT) {
priv = kzalloc(sizeof(struct u1_dev), GFP_KERNEL);
if (!priv) {
hid_device_io_stop(hdev);
hid_hw_close(hdev);
return -ENOMEM;
}
input2 = input_allocate_device();
if (!input2) {
input_free_device(input2);
goto exit;
}
priv->input2 = input2;
devInfo.dev_ctrl |= U1_SP_ABS_MODE;
ret = u1_read_write_register(hdev, ADDRESS_U1_DEV_CTRL_1,
NULL, devInfo.dev_ctrl, false);
if (ret < 0) {
dev_err(&hdev->dev, "failed SP mode (%d)\n", ret);
input_free_device(input2);
goto exit;
}
ret = u1_read_write_register(hdev, ADDRESS_U1_SP_BTN,
&devInfo.sp_btn_info, 0, true);
if (ret < 0) {
dev_err(&hdev->dev, "failed U1_SP_BTN (%d)\n", ret);
input_free_device(input2);
goto exit;
}
input2->phys = input->phys;
input2->name = "DualPoint Stick";
input2->id.bustype = BUS_I2C;
input2->id.vendor = input->id.vendor;
input2->id.product = input->id.product;
input2->id.version = input->id.version;
input2->dev.parent = input->dev.parent;
__set_bit(EV_KEY, input2->evbit);
devInfo.sp_btn_cnt = (devInfo.sp_btn_info & 0x0F);
for (i = 0; i < devInfo.sp_btn_cnt; i++)
__set_bit(BTN_LEFT + i, input2->keybit);
__set_bit(EV_REL, input2->evbit);
__set_bit(REL_X, input2->relbit);
__set_bit(REL_Y, input2->relbit);
__set_bit(INPUT_PROP_POINTER, input2->propbit);
__set_bit(INPUT_PROP_POINTING_STICK, input2->propbit);
if (input_register_device(priv->input2)) {
input_free_device(input2);
goto exit;
}
}
exit:
hid_device_io_stop(hdev);
hid_hw_close(hdev);
return ret;
}
static int alps_input_mapping(struct hid_device *hdev,
struct hid_input *hi, struct hid_field *field,
struct hid_usage *usage, unsigned long **bit, int *max)
{
return -1;
}
static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
{
struct u1_dev *data = NULL;
int ret;
data = devm_kzalloc(&hdev->dev, sizeof(struct u1_dev), GFP_KERNEL);
if (!data)
return -ENOMEM;
data->hdev = hdev;
hid_set_drvdata(hdev, data);
hdev->quirks |= HID_QUIRK_NO_INIT_REPORTS;
ret = hid_parse(hdev);
if (ret) {
hid_err(hdev, "parse failed\n");
return ret;
}
ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
if (ret) {
hid_err(hdev, "hw start failed\n");
return ret;
}
return 0;
}
static void alps_remove(struct hid_device *hdev)
{
hid_hw_stop(hdev);
kfree(priv);
}
static const struct hid_device_id alps_id[] = {
{ HID_DEVICE(HID_BUS_ANY, HID_GROUP_ANY,
USB_VENDOR_ID_ALPS_JP, HID_ANY_ID) },
{ }
};
MODULE_DEVICE_TABLE(hid, alps_id);
static struct hid_driver alps_driver = {
.name = "hid-alps",
.id_table = alps_id,
.probe = alps_probe,
.remove = alps_remove,
.raw_event = alps_raw_event,
.input_mapping = alps_input_mapping,
.input_configured = alps_input_configured,
#ifdef CONFIG_PM
.resume = alps_post_resume,
.reset_resume = alps_post_reset,
#endif
};
module_hid_driver(alps_driver);
MODULE_AUTHOR("Masaki Ota <masaki.ota@jp.alps.com>");
MODULE_DESCRIPTION("ALPS HID driver");
MODULE_LICENSE("GPL");
...@@ -70,6 +70,8 @@ ...@@ -70,6 +70,8 @@
#define USB_VENDOR_ID_ALPS 0x0433 #define USB_VENDOR_ID_ALPS 0x0433
#define USB_DEVICE_ID_IBM_GAMEPAD 0x1101 #define USB_DEVICE_ID_IBM_GAMEPAD 0x1101
#define USB_VENDOR_ID_ALPS_JP 0x044E
#define USB_VENDOR_ID_ANTON 0x1130 #define USB_VENDOR_ID_ANTON 0x1130
#define USB_DEVICE_ID_ANTON_TOUCH_PAD 0x3101 #define USB_DEVICE_ID_ANTON_TOUCH_PAD 0x3101
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment