Merge branch 'omap-for-v4.6/dt-gpmc' into omap-for-v4.6/dt

arch/arm/boot/dts/am335x-baltos-ir5221.dts

@@ -236,7 +236,11 @@ &gpmc {
 	status = "okay";
 
 	nand@0,0 {
-		reg = <0 0 0>; /* CS0, offset 0 */
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
 		ti,nand-xfer-type = "polled";
@@ -257,12 +261,9 @@ nand@0,0 {
 		gpmc,access-ns = <64>;
 		gpmc,rd-cycle-ns = <82>;
 		gpmc,wr-cycle-ns = <82>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 

arch/arm/boot/dts/am335x-chilisom.dtsi

@@ -7,6 +7,7 @@
  * published by the Free Software Foundation.
  */
 #include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Grinn AM335x ChiliSOM";
@@ -218,7 +219,11 @@ &gpmc {
 	pinctrl-0 = <&nandflash_pins>;
 	ranges = <0 0 0x08000000 0x01000000>; /* CS0 0 @addr 0x08000000, size 0x01000000 */
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>;	/* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		ti,nand-ecc-opt = "bch8";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
@@ -237,12 +242,9 @@ nand@0,0 {
 		gpmc,access-ns = <64>;
 		gpmc,rd-cycle-ns = <82>;
 		gpmc,wr-cycle-ns = <82>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 	};

arch/arm/boot/dts/am335x-cm-t335.dts

@@ -406,7 +406,11 @@ &gpmc {
 	pinctrl-0 = <&nandflash_pins>;
 	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
 	nand@0,0 {
-		reg = <0 0 0>; /* CS0, offset 0 */
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		ti,nand-ecc-opt = "bch8";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
@@ -425,12 +429,9 @@ nand@0,0 {
 		gpmc,access-ns = <64>;
 		gpmc,rd-cycle-ns = <82>;
 		gpmc,wr-cycle-ns = <82>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 		/* MTD partition table */

arch/arm/boot/dts/am335x-evm.dts

@@ -519,7 +519,11 @@ &gpmc {
 	pinctrl-0 = <&nandflash_pins_s0>;
 	ranges = <0 0 0x08000000 0x1000000>;	/* CS0: 16MB for NAND */
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		ti,nand-ecc-opt = "bch8";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
@@ -538,12 +542,9 @@ nand@0,0 {
 		gpmc,access-ns = <64>;
 		gpmc,rd-cycle-ns = <82>;
 		gpmc,wr-cycle-ns = <82>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 		/* MTD partition table */

arch/arm/boot/dts/am335x-igep0033.dtsi

@@ -11,6 +11,7 @@
 /dts-v1/;
 
 #include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	cpus {
@@ -129,7 +130,11 @@ &gpmc {
 	ranges = <0 0 0x08000000 0x1000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
 		gpmc,device-width = <1>;
@@ -147,12 +152,9 @@ nand@0,0 {
 		gpmc,access-ns = <64>;
 		gpmc,rd-cycle-ns = <82>;
 		gpmc,wr-cycle-ns = <82>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 

arch/arm/boot/dts/am335x-phycore-som.dtsi

@@ -8,6 +8,7 @@
  */
 
 #include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Phytec AM335x phyCORE";
@@ -165,7 +166,11 @@ &gpmc {
 	pinctrl-0 = <&nandflash_pins>;
 	ranges = <0 0 0x08000000 0x1000000>;   /* CS0: NAND */
 	nandflash: nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
 		gpmc,device-nand = "true";
@@ -184,13 +189,10 @@ nandflash: nand@0,0 {
 		gpmc,access-ns = <30>;
 		gpmc,rd-cycle-ns = <30>;
 		gpmc,wr-cycle-ns = <30>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <50>;
 		gpmc,cycle2cycle-diffcsen;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <30>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 

arch/arm/boot/dts/am33xx.dtsi

@@ -865,6 +865,8 @@ gpmc: gpmc@50000000 {
 			gpmc,num-waitpins = <2>;
 			#address-cells = <2>;
 			#size-cells = <1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 			status = "disabled";
 		};
 

arch/arm/boot/dts/am4372.dtsi

@@ -893,6 +893,8 @@ gpmc: gpmc@50000000 {
 			gpmc,num-waitpins = <2>;
 			#address-cells = <2>;
 			#size-cells = <1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 			status = "disabled";
 		};
 

arch/arm/boot/dts/am437x-cm-t43.dts

@@ -146,7 +146,11 @@ &gpmc {
 	pinctrl-0 = <&nand_flash_x8>;
 	ranges = <0 0 0x08000000 0x1000000>;
 	nand@0,0 {
-		reg = <0 0 0>;
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>;		/* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		ti,nand-ecc-opt = "bch8";
 		ti,elm-id = <&elm>;
 
@@ -166,17 +170,12 @@ nand@0,0 {
 		gpmc,access-ns = <64>;
 		gpmc,rd-cycle-ns = <82>;
 		gpmc,wr-cycle-ns = <82>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 
-		gpmc,wait-pin = <0>;
-
 		#address-cells = <1>;
 		#size-cells = <1>;
 		/* MTD partition table */

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -812,9 +812,13 @@ &gpmc {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&nand_flash_x8>;
-	ranges = <0 0 0 0x01000000>;	/* minimum GPMC partition = 16MB */
+	ranges = <0 0 0x08000000 0x01000000>;	/* CS0 space. Min partition = 16MB */
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>;		/* device IO registers */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		ti,nand-ecc-opt = "bch16";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
@@ -833,11 +837,9 @@ nand@0,0 {
 		gpmc,access-ns = <30>;
 		gpmc,rd-cycle-ns = <40>;
 		gpmc,wr-cycle-ns = <40>;
-		gpmc,wait-pin = <0>;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 		/* MTD partition table */

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -561,9 +561,13 @@ &gpmc {
 	status = "okay";	/* Disable QSPI when enabling GPMC (NAND) */
 	pinctrl-names = "default";
 	pinctrl-0 = <&nand_flash_x8>;
-	ranges = <0 0 0x08000000 0x1000000>;	/* CS0: 16MB for NAND */
+	ranges = <0 0 0x08000000 0x01000000>;	/* CS0 space. Min partition = 16MB */
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		ti,nand-ecc-opt = "bch16";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
@@ -582,11 +586,9 @@ nand@0,0 {
 		gpmc,access-ns = <30>; /* tCEA + 4*/
 		gpmc,rd-cycle-ns = <40>;
 		gpmc,wr-cycle-ns = <40>;
-		gpmc,wait-pin = <0>;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 		/* MTD partition table */

arch/arm/boot/dts/dm8168-evm.dts

@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "dm816x.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "DM8168 EVM";
@@ -85,8 +86,12 @@ &gpmc {
 	ranges = <0 0 0x04000000 0x01000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		linux,mtd-name= "micron,mt29f2g16aadwp";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>; /* termcount */
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ti,nand-ecc-opt = "bch8";
@@ -106,12 +111,9 @@ nand@0,0 {
 		gpmc,access-ns = <64>;
 		gpmc,rd-cycle-ns = <82>;
 		gpmc,wr-cycle-ns = <82>;
-		gpmc,wait-on-read = "true";
-		gpmc,wait-on-write = "true";
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 		partition@0 {

arch/arm/boot/dts/dm816x.dtsi

@@ -183,6 +183,8 @@ gpmc: gpmc@50000000 {
 			dma-names = "rxtx";
 			gpmc,num-cs = <6>;
 			gpmc,num-waitpins = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		i2c1: i2c@48028000 {

arch/arm/boot/dts/dra7-evm.dts

@@ -741,9 +741,13 @@ &gpmc {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&nand_flash_x16>;
-	ranges = <0 0 0 0x01000000>;	/* minimum GPMC partition = 16MB */
+	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>;		/* device IO registers */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>; /* termcount */
 		ti,nand-ecc-opt = "bch8";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <16>;
@@ -766,7 +770,6 @@ nand@0,0 {
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 		/* MTD partition table */
 		/* All SPL-* partitions are sized to minimal length

arch/arm/boot/dts/dra7.dtsi

@@ -1402,6 +1402,8 @@ gpmc: gpmc@50000000 {
 			gpmc,num-waitpins = <2>;
 			#address-cells = <2>;
 			#size-cells = <1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 			status = "disabled";
 		};
 

arch/arm/boot/dts/dra72-evm.dts

@@ -492,13 +492,17 @@ &gpmc {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&nand_default>;
-	ranges = <0 0 0 0x01000000>;	/* minimum GPMC partition = 16MB */
+	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
 	nand@0,0 {
 		/* To use NAND, DIP switch SW5 must be set like so:
 		 * SW5.1 (NAND_SELn) = ON (LOW)
 		 * SW5.9 (GPMC_WPN) = OFF (HIGH)
 		 */
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>;		/* device IO registers */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		ti,nand-ecc-opt = "bch8";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <16>;
@@ -521,7 +525,6 @@ nand@0,0 {
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 		/* MTD partition table */
 		/* All SPL-* partitions are sized to minimal length

arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts

@@ -102,7 +102,8 @@ &charger {
 };
 
 &gpmc {
-	ranges = <1 0 0x08000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
+	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
+		  1 0 0x2c000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
 
 	ethernet@gpmc {
 		pinctrl-names = "default";

arch/arm/boot/dts/logicpd-torpedo-som.dtsi

@@ -35,11 +35,15 @@ wl12xx_vmmc: wl12xx_vmmc {
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x1000000>;	/* CS0: 16MB for NAND */
+	ranges = <0 0 0x30000000 0x1000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
-		linux,mtd-name = "micron,mt29f4g16abbda3w";
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
+		linux,mtd-name = "micron,mt29f4g16abbda3w";
 		nand-bus-width = <16>;
 		ti,nand-ecc-opt = "bch8";
 		gpmc,sync-clk-ps = <0>;

arch/arm/boot/dts/omap3-beagle.dts

@@ -384,8 +384,11 @@ &gpmc {
 
 	/* Chip select 0 */
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>;		/* NAND I/O window, 4 bytes */
-		interrupts = <20>;
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		ti,nand-ecc-opt = "ham1";
 		nand-bus-width = <16>;
 		#address-cells = <1>;

arch/arm/boot/dts/omap3-cm-t3x.dtsi

@@ -261,10 +261,14 @@ &mcbsp2 {
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x01000000>;
+	ranges = <0 0 0x30000000 0x01000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>;	/* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
 		ti,nand-ecc-opt = "sw";

arch/arm/boot/dts/omap3-devkit8000-common.dtsi

@@ -204,7 +204,11 @@ &gpmc {
 	ranges = <0 0 0x30000000 0x1000000>;       /* CS0: 16MB for NAND */
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "sw";

arch/arm/boot/dts/omap3-evm-37xx.dts

@@ -154,12 +154,16 @@ &uart3 {
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x1000000>,	/* CS0: 16MB for NAND */
+	ranges = <0 0 0x30000000 0x1000000>,	/* CS0: 16MB for NAND */
 		 <5 0 0x2c000000 0x01000000>;
 
 	nand@0,0 {
-		linux,mtd-name= "hynix,h8kds0un0mer-4em";
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
+		linux,mtd-name= "hynix,h8kds0un0mer-4em";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -492,7 +492,11 @@ &gpmc {
 	ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <16>;
 		ti,nand-ecc-opt = "bch8";
 

arch/arm/boot/dts/omap3-igep.dtsi

@@ -99,8 +99,12 @@ OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)	/* i2c3_sda.i2c3_sda */
 
 &gpmc {
 	nand@0,0 {
-		linux,mtd-name= "micron,mt29c4g96maz";
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
+		linux,mtd-name= "micron,mt29c4g96maz";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";

arch/arm/boot/dts/omap3-igep0020-common.dtsi

@@ -210,8 +210,8 @@ eeprom@50 {
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x20000000>,
-		 <5 0 0x2c000000 0x01000000>;
+	ranges = <0 0 0x30000000 0x01000000>,	/* CS0: 16MB for NAND */
+		 <5 0 0x2c000000 0x01000000>;	/* CS5: 16MB for ethernet */
 
 	ethernet@gpmc {
 		pinctrl-names = "default";

arch/arm/boot/dts/omap3-igep0030-common.dtsi

@@ -99,3 +99,7 @@ &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart2_pins>;
 };
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x01000000>;   /* CS0: 16MB for NAND */
+};

arch/arm/boot/dts/omap3-ldp.dts

@@ -97,12 +97,16 @@ key_down {
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x01000000>,
-		 <1 0 0x08000000 0x01000000>;
+	ranges = <0 0 0x30000000 0x1000000>,	/* CS0 space, 16MB */
+		 <1 0 0x08000000 0x1000000>;	/* CS1 space, 16MB */
 
 	nand@0,0 {
-		linux,mtd-name= "micron,nand";
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
+		linux,mtd-name= "micron,nand";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";

arch/arm/boot/dts/omap3-lilly-a83x.dtsi

@@ -362,7 +362,11 @@ &gpmc {
 		<7 0 0x15000000 0x01000000>;
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <16>;
 		ti,nand-ecc-opt = "bch8";
 		/* no elm on omap3 */

arch/arm/boot/dts/omap3-overo-base.dtsi

@@ -226,8 +226,12 @@ &gpmc {
 	ranges = <0 0 0x00000000 0x20000000>;
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		linux,mtd-name= "micron,mt29c4g96maz";
-		reg = <0 0 0>;
+		reg = <0 0 4>;	/* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";

arch/arm/boot/dts/omap3-pandora-common.dtsi

@@ -546,7 +546,11 @@ &gpmc {
 	ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <16>;
 		ti,nand-ecc-opt = "sw";
 

arch/arm/boot/dts/omap3-tao3530.dtsi

@@ -275,10 +275,14 @@ &mcbsp3 {
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x01000000>;
+	ranges = <0 0 0x30000000 0x01000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
+		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;	/* GPMC_DEVWIDTH_16BIT */
 		ti,nand-ecc-opt = "sw";

arch/arm/boot/dts/omap3.dtsi

@@ -723,6 +723,8 @@ gpmc: gpmc@6e000000 {
 			gpmc,num-waitpins = <4>;
 			#address-cells = <2>;
 			#size-cells = <1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		usb_otg_hs: usb_otg_hs@480ab000 {

arch/arm/boot/dts/omap3430-sdp.dts

@@ -103,10 +103,14 @@ partition@280000 {
 	};
 
 	nand@1,0 {
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+			     <1 IRQ_TYPE_NONE>;	/* termcount */
 		linux,mtd-name= "micron,mt29f1g08abb";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		reg = <1 0 4>;	/* CS1, offset 0, IO size 4 */
 		ti,nand-ecc-opt = "sw";
 		nand-bus-width = <8>;
 		gpmc,cs-on-ns = <0>;