net: qualcomm: new Ethernet over SPI driver for QCA7000

This patch adds the Ethernet over SPI driver for the
Qualcomm QCA7000 HomePlug GreenPHY.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/Kconfig

@@ -150,6 +150,7 @@ config ETHOC
 source "drivers/net/ethernet/packetengines/Kconfig"
 source "drivers/net/ethernet/pasemi/Kconfig"
 source "drivers/net/ethernet/qlogic/Kconfig"
+source "drivers/net/ethernet/qualcomm/Kconfig"
 source "drivers/net/ethernet/realtek/Kconfig"
 source "drivers/net/ethernet/renesas/Kconfig"
 source "drivers/net/ethernet/rdc/Kconfig"

drivers/net/ethernet/Makefile

@@ -60,6 +60,7 @@ obj-$(CONFIG_ETHOC) += ethoc.o
 obj-$(CONFIG_NET_PACKET_ENGINE) += packetengines/
 obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
 obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
+obj-$(CONFIG_NET_VENDOR_QUALCOMM) += qualcomm/
 obj-$(CONFIG_NET_VENDOR_REALTEK) += realtek/
 obj-$(CONFIG_SH_ETH) += renesas/
 obj-$(CONFIG_NET_VENDOR_RDC) += rdc/

drivers/net/ethernet/qualcomm/Kconfig

+#
+# Qualcomm network device configuration
+#
+
+config NET_VENDOR_QUALCOMM
+	bool "Qualcomm devices"
+	default y
+	depends on SPI_MASTER && OF_GPIO
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Qualcomm cards. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_QUALCOMM
+
+config QCA7000
+	tristate "Qualcomm Atheros QCA7000 support"
+	depends on SPI_MASTER && OF_GPIO
+	---help---
+	  This SPI protocol driver supports the Qualcomm Atheros QCA7000.
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called qcaspi.
+
+endif # NET_VENDOR_QUALCOMM

drivers/net/ethernet/qualcomm/Makefile

+#
+# Makefile for the Qualcomm network device drivers.
+#
+
+obj-$(CONFIG_QCA7000) += qcaspi.o
+qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o

drivers/net/ethernet/qualcomm/qca_7k.c

+/*
+ *
+ *   Copyright (c) 2011, 2012, Qualcomm Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/*   This module implements the Qualcomm Atheros SPI protocol for
+ *   kernel-based SPI device.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/spi/spi.h>
+#include <linux/version.h>
+
+#include "qca_7k.h"
+
+void
+qcaspi_spi_error(struct qcaspi *qca)
+{
+	if (qca->sync != QCASPI_SYNC_READY)
+		return;
+
+	netdev_err(qca->net_dev, "spi error\n");
+	qca->sync = QCASPI_SYNC_UNKNOWN;
+	qca->stats.spi_err++;
+}
+
+int
+qcaspi_read_register(struct qcaspi *qca, u16 reg, u16 *result)
+{
+	__be16 rx_data;
+	__be16 tx_data;
+	struct spi_transfer *transfer;
+	struct spi_message *msg;
+	int ret;
+
+	tx_data = cpu_to_be16(QCA7K_SPI_READ | QCA7K_SPI_INTERNAL | reg);
+
+	if (qca->legacy_mode) {
+		msg = &qca->spi_msg1;
+		transfer = &qca->spi_xfer1;
+		transfer->tx_buf = &tx_data;
+		transfer->rx_buf = NULL;
+		transfer->len = QCASPI_CMD_LEN;
+		spi_sync(qca->spi_dev, msg);
+	} else {
+		msg = &qca->spi_msg2;
+		transfer = &qca->spi_xfer2[0];
+		transfer->tx_buf = &tx_data;
+		transfer->rx_buf = NULL;
+		transfer->len = QCASPI_CMD_LEN;
+		transfer = &qca->spi_xfer2[1];
+	}
+	transfer->tx_buf = NULL;
+	transfer->rx_buf = &rx_data;
+	transfer->len = QCASPI_CMD_LEN;
+	ret = spi_sync(qca->spi_dev, msg);
+
+	if (!ret)
+		ret = msg->status;
+
+	if (ret)
+		qcaspi_spi_error(qca);
+	else
+		*result = be16_to_cpu(rx_data);
+
+	return ret;
+}
+
+int
+qcaspi_write_register(struct qcaspi *qca, u16 reg, u16 value)
+{
+	__be16 tx_data[2];
+	struct spi_transfer *transfer;
+	struct spi_message *msg;
+	int ret;
+
+	tx_data[0] = cpu_to_be16(QCA7K_SPI_WRITE | QCA7K_SPI_INTERNAL | reg);
+	tx_data[1] = cpu_to_be16(value);
+
+	if (qca->legacy_mode) {
+		msg = &qca->spi_msg1;
+		transfer = &qca->spi_xfer1;
+		transfer->tx_buf = &tx_data[0];
+		transfer->rx_buf = NULL;
+		transfer->len = QCASPI_CMD_LEN;
+		spi_sync(qca->spi_dev, msg);
+	} else {
+		msg = &qca->spi_msg2;
+		transfer = &qca->spi_xfer2[0];
+		transfer->tx_buf = &tx_data[0];
+		transfer->rx_buf = NULL;
+		transfer->len = QCASPI_CMD_LEN;
+		transfer = &qca->spi_xfer2[1];
+	}
+	transfer->tx_buf = &tx_data[1];
+	transfer->rx_buf = NULL;
+	transfer->len = QCASPI_CMD_LEN;
+	ret = spi_sync(qca->spi_dev, msg);
+
+	if (!ret)
+		ret = msg->status;
+
+	if (ret)
+		qcaspi_spi_error(qca);
+
+	return ret;
+}
+
+int
+qcaspi_tx_cmd(struct qcaspi *qca, u16 cmd)
+{
+	__be16 tx_data;
+	struct spi_message *msg = &qca->spi_msg1;
+	struct spi_transfer *transfer = &qca->spi_xfer1;
+	int ret;
+
+	tx_data = cpu_to_be16(cmd);
+	transfer->len = sizeof(tx_data);
+	transfer->tx_buf = &tx_data;
+	transfer->rx_buf = NULL;
+
+	ret = spi_sync(qca->spi_dev, msg);
+
+	if (!ret)
+		ret = msg->status;
+
+	if (ret)
+		qcaspi_spi_error(qca);
+
+	return ret;
+}

drivers/net/ethernet/qualcomm/qca_7k.h

+/*
+ *   Copyright (c) 2011, 2012, Qualcomm Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/*   Qualcomm Atheros SPI register definition.
+ *
+ *   This module is designed to define the Qualcomm Atheros SPI
+ *   register placeholders.
+ */
+
+#ifndef _QCA_7K_H
+#define _QCA_7K_H
+
+#include <linux/types.h>
+
+#include "qca_spi.h"
+
+#define QCA7K_SPI_READ     (1 << 15)
+#define QCA7K_SPI_WRITE    (0 << 15)
+#define QCA7K_SPI_INTERNAL (1 << 14)
+#define QCA7K_SPI_EXTERNAL (0 << 14)
+
+#define QCASPI_CMD_LEN    2
+#define QCASPI_HW_PKT_LEN 4
+#define QCASPI_HW_BUF_LEN 0xC5B
+
+/*   SPI registers;                               */
+#define SPI_REG_BFR_SIZE        0x0100
+#define SPI_REG_WRBUF_SPC_AVA   0x0200
+#define SPI_REG_RDBUF_BYTE_AVA  0x0300
+#define SPI_REG_SPI_CONFIG      0x0400
+#define SPI_REG_SPI_STATUS      0x0500
+#define SPI_REG_INTR_CAUSE      0x0C00
+#define SPI_REG_INTR_ENABLE     0x0D00
+#define SPI_REG_RDBUF_WATERMARK 0x1200
+#define SPI_REG_WRBUF_WATERMARK 0x1300
+#define SPI_REG_SIGNATURE       0x1A00
+#define SPI_REG_ACTION_CTRL     0x1B00
+
+/*   SPI_CONFIG register definition;             */
+#define QCASPI_SLAVE_RESET_BIT (1 << 6)
+
+/*   INTR_CAUSE/ENABLE register definition.      */
+#define SPI_INT_WRBUF_BELOW_WM (1 << 10)
+#define SPI_INT_CPU_ON         (1 << 6)
+#define SPI_INT_ADDR_ERR       (1 << 3)
+#define SPI_INT_WRBUF_ERR      (1 << 2)
+#define SPI_INT_RDBUF_ERR      (1 << 1)
+#define SPI_INT_PKT_AVLBL      (1 << 0)
+
+void qcaspi_spi_error(struct qcaspi *qca);
+int qcaspi_read_register(struct qcaspi *qca, u16 reg, u16 *result);
+int qcaspi_write_register(struct qcaspi *qca, u16 reg, u16 value);
+int qcaspi_tx_cmd(struct qcaspi *qca, u16 cmd);
+
+#endif /* _QCA_7K_H */

drivers/net/ethernet/qualcomm/qca_debug.c

+/*
+ *   Copyright (c) 2011, 2012, Qualcomm Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*   This file contains debugging routines for use in the QCA7K driver.
+ */
+
+#include <linux/debugfs.h>
+#include <linux/ethtool.h>
+#include <linux/seq_file.h>
+#include <linux/types.h>
+
+#include "qca_7k.h"
+#include "qca_debug.h"
+
+#define QCASPI_MAX_REGS 0x20
+
+static const u16 qcaspi_spi_regs[] = {
+	SPI_REG_BFR_SIZE,
+	SPI_REG_WRBUF_SPC_AVA,
+	SPI_REG_RDBUF_BYTE_AVA,
+	SPI_REG_SPI_CONFIG,
+	SPI_REG_SPI_STATUS,
+	SPI_REG_INTR_CAUSE,
+	SPI_REG_INTR_ENABLE,
+	SPI_REG_RDBUF_WATERMARK,
+	SPI_REG_WRBUF_WATERMARK,
+	SPI_REG_SIGNATURE,
+	SPI_REG_ACTION_CTRL
+};
+
+/* The order of these strings must match the order of the fields in
+ * struct qcaspi_stats
+ * See qca_spi.h
+ */
+static const char qcaspi_gstrings_stats[][ETH_GSTRING_LEN] = {
+	"Triggered resets",
+	"Device resets",
+	"Reset timeouts",
+	"Read errors",
+	"Write errors",
+	"Read buffer errors",
+	"Write buffer errors",
+	"Out of memory",
+	"Write buffer misses",
+	"Transmit ring full",
+	"SPI errors",
+};
+
+#ifdef CONFIG_DEBUG_FS
+
+static int
+qcaspi_info_show(struct seq_file *s, void *what)
+{
+	struct qcaspi *qca = s->private;
+
+	seq_printf(s, "RX buffer size   : %lu\n",
+		   (unsigned long)qca->buffer_size);
+
+	seq_puts(s, "TX ring state    : ");
+
+	if (qca->txr.skb[qca->txr.head] == NULL)
+		seq_puts(s, "empty");
+	else if (qca->txr.skb[qca->txr.tail])
+		seq_puts(s, "full");
+	else
+		seq_puts(s, "in use");
+
+	seq_puts(s, "\n");
+
+	seq_printf(s, "TX ring size     : %u\n",
+		   qca->txr.size);
+
+	seq_printf(s, "Sync state       : %u (",
+		   (unsigned int)qca->sync);
+	switch (qca->sync) {
+	case QCASPI_SYNC_UNKNOWN:
+		seq_puts(s, "QCASPI_SYNC_UNKNOWN");
+		break;
+	case QCASPI_SYNC_RESET:
+		seq_puts(s, "QCASPI_SYNC_RESET");
+		break;
+	case QCASPI_SYNC_READY:
+		seq_puts(s, "QCASPI_SYNC_READY");
+		break;
+	default:
+		seq_puts(s, "INVALID");
+		break;
+	}
+	seq_puts(s, ")\n");
+
+	seq_printf(s, "IRQ              : %d\n",
+		   qca->spi_dev->irq);
+	seq_printf(s, "INTR REQ         : %u\n",
+		   qca->intr_req);
+	seq_printf(s, "INTR SVC         : %u\n",
+		   qca->intr_svc);
+
+	seq_printf(s, "SPI max speed    : %lu\n",
+		   (unsigned long)qca->spi_dev->max_speed_hz);
+	seq_printf(s, "SPI mode         : %x\n",
+		   qca->spi_dev->mode);
+	seq_printf(s, "SPI chip select  : %u\n",
+		   (unsigned int)qca->spi_dev->chip_select);
+	seq_printf(s, "SPI legacy mode  : %u\n",
+		   (unsigned int)qca->legacy_mode);
+	seq_printf(s, "SPI burst length : %u\n",
+		   (unsigned int)qca->burst_len);
+
+	return 0;
+}
+
+static int
+qcaspi_info_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, qcaspi_info_show, inode->i_private);
+}
+
+static const struct file_operations qcaspi_info_ops = {
+	.open = qcaspi_info_open,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.release = single_release,
+};
+
+void
+qcaspi_init_device_debugfs(struct qcaspi *qca)
+{
+	struct dentry *device_root;
+
+	device_root = debugfs_create_dir(dev_name(&qca->net_dev->dev), NULL);
+	qca->device_root = device_root;
+
+	if (IS_ERR(device_root) || !device_root) {
+		pr_warn("failed to create debugfs directory for %s\n",
+			dev_name(&qca->net_dev->dev));
+		return;
+	}
+	debugfs_create_file("info", S_IFREG | S_IRUGO, device_root, qca,
+			    &qcaspi_info_ops);
+}
+
+void
+qcaspi_remove_device_debugfs(struct qcaspi *qca)
+{
+	debugfs_remove_recursive(qca->device_root);
+}
+
+#else /* CONFIG_DEBUG_FS */
+
+void
+qcaspi_init_device_debugfs(struct qcaspi *qca)
+{
+}
+
+void
+qcaspi_remove_device_debugfs(struct qcaspi *qca)
+{
+}
+
+#endif
+
+static void
+qcaspi_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *p)
+{
+	struct qcaspi *qca = netdev_priv(dev);
+
+	strlcpy(p->driver, QCASPI_DRV_NAME, sizeof(p->driver));
+	strlcpy(p->version, QCASPI_DRV_VERSION, sizeof(p->version));
+	strlcpy(p->fw_version, "QCA7000", sizeof(p->fw_version));
+	strlcpy(p->bus_info, dev_name(&qca->spi_dev->dev),
+		sizeof(p->bus_info));
+}
+
+static int
+qcaspi_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	cmd->transceiver = XCVR_INTERNAL;
+	cmd->supported = SUPPORTED_10baseT_Half;
+	ethtool_cmd_speed_set(cmd,  SPEED_10);
+	cmd->duplex = DUPLEX_HALF;
+	cmd->port = PORT_OTHER;
+	cmd->autoneg = AUTONEG_DISABLE;
+
+	return 0;
+}
+
+static void
+qcaspi_get_ethtool_stats(struct net_device *dev, struct ethtool_stats *estats, u64 *data)
+{
+	struct qcaspi *qca = netdev_priv(dev);
+	struct qcaspi_stats *st = &qca->stats;
+
+	memcpy(data, st, ARRAY_SIZE(qcaspi_gstrings_stats) * sizeof(u64));
+}
+
+static void
+qcaspi_get_strings(struct net_device *dev, u32 stringset, u8 *buf)
+{
+	switch (stringset) {
+	case ETH_SS_STATS:
+		memcpy(buf, &qcaspi_gstrings_stats,
+		       sizeof(qcaspi_gstrings_stats));
+		break;
+	default:
+		WARN_ON(1);
+		break;
+	}
+}
+
+static int
+qcaspi_get_sset_count(struct net_device *dev, int sset)
+{
+	switch (sset) {
+	case ETH_SS_STATS:
+		return ARRAY_SIZE(qcaspi_gstrings_stats);
+	default:
+		return -EINVAL;
+	}
+}
+
+static int
+qcaspi_get_regs_len(struct net_device *dev)
+{
+	return sizeof(u32) * QCASPI_MAX_REGS;
+}
+
+static void
+qcaspi_get_regs(struct net_device *dev, struct ethtool_regs *regs, void *p)
+{
+	struct qcaspi *qca = netdev_priv(dev);
+	u32 *regs_buff = p;
+	unsigned int i;
+
+	regs->version = 1;
+	memset(regs_buff, 0, sizeof(u32) * QCASPI_MAX_REGS);
+
+	for (i = 0; i < ARRAY_SIZE(qcaspi_spi_regs); i++) {
+		u16 offset, value;
+
+		qcaspi_read_register(qca, qcaspi_spi_regs[i], &value);
+		offset = qcaspi_spi_regs[i] >> 8;
+		regs_buff[offset] = value;
+	}
+}
+
+static void
+qcaspi_get_ringparam(struct net_device *dev, struct ethtool_ringparam *ring)
+{
+	struct qcaspi *qca = netdev_priv(dev);
+
+	ring->rx_max_pending = 4;
+	ring->tx_max_pending = TX_RING_MAX_LEN;
+	ring->rx_pending = 4;
+	ring->tx_pending = qca->txr.count;
+}
+
+static int
+qcaspi_set_ringparam(struct net_device *dev, struct ethtool_ringparam *ring)
+{
+	struct qcaspi *qca = netdev_priv(dev);
+
+	if ((ring->rx_pending) ||
+	    (ring->rx_mini_pending) ||
+	    (ring->rx_jumbo_pending))
+		return -EINVAL;
+
+	if (netif_running(dev))
+		qcaspi_netdev_close(dev);
+
+	qca->txr.count = max_t(u32, ring->tx_pending, TX_RING_MIN_LEN);
+	qca->txr.count = min_t(u16, qca->txr.count, TX_RING_MAX_LEN);
+
+	if (netif_running(dev))
+		qcaspi_netdev_open(dev);
+
+	return 0;
+}
+
+static const struct ethtool_ops qcaspi_ethtool_ops = {
+	.get_drvinfo = qcaspi_get_drvinfo,
+	.get_link = ethtool_op_get_link,
+	.get_settings = qcaspi_get_settings,
+	.get_ethtool_stats = qcaspi_get_ethtool_stats,
+	.get_strings = qcaspi_get_strings,
+	.get_sset_count = qcaspi_get_sset_count,
+	.get_regs_len = qcaspi_get_regs_len,
+	.get_regs = qcaspi_get_regs,
+	.get_ringparam = qcaspi_get_ringparam,
+	.set_ringparam = qcaspi_set_ringparam,
+};
+
+void qcaspi_set_ethtool_ops(struct net_device *dev)
+{
+	dev->ethtool_ops = &qcaspi_ethtool_ops;
+}

drivers/net/ethernet/qualcomm/qca_debug.h

+/*
+ *   Copyright (c) 2011, 2012, Qualcomm Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*   This file contains debugging routines for use in the QCA7K driver.
+ */
+
+#ifndef _QCA_DEBUG_H
+#define _QCA_DEBUG_H
+
+#include "qca_spi.h"
+
+void qcaspi_init_device_debugfs(struct qcaspi *qca);
+
+void qcaspi_remove_device_debugfs(struct qcaspi *qca);
+
+void qcaspi_set_ethtool_ops(struct net_device *dev);
+
+#endif /* _QCA_DEBUG_H */

drivers/net/ethernet/qualcomm/qca_framing.c

+/*
+ *   Copyright (c) 2011, 2012, Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*   Atheros ethernet framing. Every Ethernet frame is surrounded
+ *   by an atheros frame while transmitted over a serial channel;
+ */
+
+#include <linux/kernel.h>
+
+#include "qca_framing.h"
+
+u16
+qcafrm_create_header(u8 *buf, u16 length)
+{
+	__le16 len;
+
+	if (!buf)
+		return 0;
+
+	len = cpu_to_le16(length);
+
+	buf[0] = 0xAA;
+	buf[1] = 0xAA;
+	buf[2] = 0xAA;
+	buf[3] = 0xAA;
+	buf[4] = len & 0xff;
+	buf[5] = (len >> 8) & 0xff;
+	buf[6] = 0;
+	buf[7] = 0;
+
+	return QCAFRM_HEADER_LEN;
+}
+
+u16
+qcafrm_create_footer(u8 *buf)
+{
+	if (!buf)
+		return 0;
+
+	buf[0] = 0x55;
+	buf[1] = 0x55;
+	return QCAFRM_FOOTER_LEN;
+}
+
+/*   Gather received bytes and try to extract a full ethernet frame by
+ *   following a simple state machine.
+ *
+ * Return:   QCAFRM_GATHER       No ethernet frame fully received yet.
+ *           QCAFRM_NOHEAD       Header expected but not found.
+ *           QCAFRM_INVLEN       Atheros frame length is invalid
+ *           QCAFRM_NOTAIL       Footer expected but not found.
+ *           > 0                 Number of byte in the fully received
+ *                               Ethernet frame
+ */
+
+s32
+qcafrm_fsm_decode(struct qcafrm_handle *handle, u8 *buf, u16 buf_len, u8 recv_byte)
+{
+	s32 ret = QCAFRM_GATHER;
+	u16 len;
+
+	switch (handle->state) {
+	case QCAFRM_HW_LEN0:
+	case QCAFRM_HW_LEN1:
+		/* by default, just go to next state */
+		handle->state--;
+
+		if (recv_byte != 0x00) {
+			/* first two bytes of length must be 0 */
+			handle->state = QCAFRM_HW_LEN0;
+		}
+		break;
+	case QCAFRM_HW_LEN2:
+	case QCAFRM_HW_LEN3:
+		handle->state--;
+		break;
+	/* 4 bytes header pattern */
+	case QCAFRM_WAIT_AA1:
+	case QCAFRM_WAIT_AA2:
+	case QCAFRM_WAIT_AA3:
+	case QCAFRM_WAIT_AA4:
+		if (recv_byte != 0xAA) {
+			ret = QCAFRM_NOHEAD;
+			handle->state = QCAFRM_HW_LEN0;
+		} else {
+			handle->state--;
+		}
+		break;
+		/* 2 bytes length. */
+		/* Borrow offset field to hold length for now. */
+	case QCAFRM_WAIT_LEN_BYTE0:
+		handle->offset = recv_byte;
+		handle->state = QCAFRM_WAIT_LEN_BYTE1;
+		break;
+	case QCAFRM_WAIT_LEN_BYTE1:
+		handle->offset = handle->offset | (recv_byte << 8);
+		handle->state = QCAFRM_WAIT_RSVD_BYTE1;
+		break;
+	case QCAFRM_WAIT_RSVD_BYTE1:
+		handle->state = QCAFRM_WAIT_RSVD_BYTE2;
+		break;
+	case QCAFRM_WAIT_RSVD_BYTE2:
+		len = handle->offset;
+		if (len > buf_len || len < QCAFRM_ETHMINLEN) {
+			ret = QCAFRM_INVLEN;
+			handle->state = QCAFRM_HW_LEN0;
+		} else {
+			handle->state = (enum qcafrm_state)(len + 1);
+			/* Remaining number of bytes. */
+			handle->offset = 0;
+		}
+		break;
+	default:
+		/* Receiving Ethernet frame itself. */
+		buf[handle->offset] = recv_byte;
+		handle->offset++;
+		handle->state--;
+		break;
+	case QCAFRM_WAIT_551:
+		if (recv_byte != 0x55) {
+			ret = QCAFRM_NOTAIL;
+			handle->state = QCAFRM_HW_LEN0;
+		} else {
+			handle->state = QCAFRM_WAIT_552;
+		}
+		break;
+	case QCAFRM_WAIT_552:
+		if (recv_byte != 0x55) {
+			ret = QCAFRM_NOTAIL;
+			handle->state = QCAFRM_HW_LEN0;
+		} else {
+			ret = handle->offset;
+			/* Frame is fully received. */
+			handle->state = QCAFRM_HW_LEN0;
+		}
+		break;
+	}
+
+	return ret;
+}

drivers/net/ethernet/qualcomm/qca_framing.h

+/*
+ *   Copyright (c) 2011, 2012, Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*   Atheros Ethernet framing. Every Ethernet frame is surrounded by an atheros
+ *   frame while transmitted over a serial channel.
+ */
+
+#ifndef _QCA_FRAMING_H
+#define _QCA_FRAMING_H
+
+#include <linux/if_ether.h>
+#include <linux/if_vlan.h>
+#include <linux/types.h>
+
+/* Frame is currently being received */
+#define QCAFRM_GATHER 0
+
+/*  No header byte while expecting it */
+#define QCAFRM_NOHEAD (QCAFRM_ERR_BASE - 1)
+
+/* No tailer byte while expecting it */
+#define QCAFRM_NOTAIL (QCAFRM_ERR_BASE - 2)
+
+/* Frame length is invalid */
+#define QCAFRM_INVLEN (QCAFRM_ERR_BASE - 3)
+
+/* Frame length is invalid */
+#define QCAFRM_INVFRAME (QCAFRM_ERR_BASE - 4)
+
+/* Min/Max Ethernet MTU */
+#define QCAFRM_ETHMINMTU 46
+#define QCAFRM_ETHMAXMTU 1500
+
+/* Min/Max frame lengths */
+#define QCAFRM_ETHMINLEN (QCAFRM_ETHMINMTU + ETH_HLEN)
+#define QCAFRM_ETHMAXLEN (QCAFRM_ETHMAXMTU + VLAN_ETH_HLEN)
+
+/* QCA7K header len */
+#define QCAFRM_HEADER_LEN 8
+
+/* QCA7K footer len */
+#define QCAFRM_FOOTER_LEN 2
+
+/* QCA7K Framing. */
+#define QCAFRM_ERR_BASE -1000
+
+enum qcafrm_state {
+	QCAFRM_HW_LEN0 = 0x8000,
+	QCAFRM_HW_LEN1 = QCAFRM_HW_LEN0 - 1,
+	QCAFRM_HW_LEN2 = QCAFRM_HW_LEN1 - 1,
+	QCAFRM_HW_LEN3 = QCAFRM_HW_LEN2 - 1,
+
+	/*  Waiting first 0xAA of header */
+	QCAFRM_WAIT_AA1 = QCAFRM_HW_LEN3 - 1,
+
+	/*  Waiting second 0xAA of header */
+	QCAFRM_WAIT_AA2 = QCAFRM_WAIT_AA1 - 1,
+
+	/*  Waiting third 0xAA of header */
+	QCAFRM_WAIT_AA3 = QCAFRM_WAIT_AA2 - 1,
+
+	/*  Waiting fourth 0xAA of header */
+	QCAFRM_WAIT_AA4 = QCAFRM_WAIT_AA3 - 1,
+
+	/*  Waiting Byte 0-1 of length (litte endian) */
+	QCAFRM_WAIT_LEN_BYTE0 = QCAFRM_WAIT_AA4 - 1,
+	QCAFRM_WAIT_LEN_BYTE1 = QCAFRM_WAIT_AA4 - 2,
+
+	/* Reserved bytes */
+	QCAFRM_WAIT_RSVD_BYTE1 = QCAFRM_WAIT_AA4 - 3,
+	QCAFRM_WAIT_RSVD_BYTE2 = QCAFRM_WAIT_AA4 - 4,
+
+	/*  The frame length is used as the state until
+	 *  the end of the Ethernet frame
+	 *  Waiting for first 0x55 of footer
+	 */
+	QCAFRM_WAIT_551 = 1,
+
+	/*  Waiting for second 0x55 of footer */
+	QCAFRM_WAIT_552 = QCAFRM_WAIT_551 - 1
+};
+
+/*   Structure to maintain the frame decoding during reception. */
+
+struct qcafrm_handle {
+	/*  Current decoding state */
+	enum qcafrm_state state;
+
+	/* Offset in buffer (borrowed for length too) */
+	s16 offset;
+
+	/* Frame length as kept by this module */
+	u16 len;
+};
+
+u16 qcafrm_create_header(u8 *buf, u16 len);
+
+u16 qcafrm_create_footer(u8 *buf);
+
+static inline void qcafrm_fsm_init(struct qcafrm_handle *handle)
+{
+	handle->state = QCAFRM_HW_LEN0;
+}
+
+/*   Gather received bytes and try to extract a full Ethernet frame
+ *   by following a simple state machine.
+ *
+ * Return:   QCAFRM_GATHER       No Ethernet frame fully received yet.
+ *           QCAFRM_NOHEAD       Header expected but not found.
+ *           QCAFRM_INVLEN       QCA7K frame length is invalid
+ *           QCAFRM_NOTAIL       Footer expected but not found.
+ *           > 0                 Number of byte in the fully received
+ *                               Ethernet frame
+ */
+
+s32 qcafrm_fsm_decode(struct qcafrm_handle *handle, u8 *buf, u16 buf_len, u8 recv_byte);
+
+#endif /* _QCA_FRAMING_H */

drivers/net/ethernet/qualcomm/qca_spi.h

+/*
+ *   Copyright (c) 2011, 2012, Qualcomm Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*   Qualcomm Atheros SPI register definition.
+ *
+ *   This module is designed to define the Qualcomm Atheros SPI register
+ *   placeholders;
+ */
+
+#ifndef _QCA_SPI_H
+#define _QCA_SPI_H
+
+#include <linux/netdevice.h>
+#include <linux/sched.h>
+#include <linux/skbuff.h>
+#include <linux/spi/spi.h>
+#include <linux/types.h>
+
+#include "qca_framing.h"
+
+#define QCASPI_DRV_VERSION "0.2.7-i"
+#define QCASPI_DRV_NAME    "qcaspi"
+
+#define QCASPI_GOOD_SIGNATURE 0xAA55
+
+#define TX_RING_MAX_LEN 10
+#define TX_RING_MIN_LEN 2
+
+/* sync related constants */
+#define QCASPI_SYNC_UNKNOWN 0
+#define QCASPI_SYNC_RESET   1
+#define QCASPI_SYNC_READY   2
+
+#define QCASPI_RESET_TIMEOUT 10
+
+/* sync events */
+#define QCASPI_EVENT_UPDATE 0
+#define QCASPI_EVENT_CPUON  1
+
+struct tx_ring {
+	struct sk_buff *skb[TX_RING_MAX_LEN];
+	u16 head;
+	u16 tail;
+	u16 size;
+	u16 count;
+};
+
+struct qcaspi_stats {
+	u64 trig_reset;
+	u64 device_reset;
+	u64 reset_timeout;
+	u64 read_err;
+	u64 write_err;
+	u64 read_buf_err;
+	u64 write_buf_err;
+	u64 out_of_mem;
+	u64 write_buf_miss;
+	u64 ring_full;
+	u64 spi_err;
+};
+
+struct qcaspi {
+	struct net_device *net_dev;
+	struct spi_device *spi_dev;
+	struct task_struct *spi_thread;
+
+	struct tx_ring txr;
+	struct qcaspi_stats stats;
+
+	struct spi_message spi_msg1;
+	struct spi_message spi_msg2;
+	struct spi_transfer spi_xfer1;
+	struct spi_transfer spi_xfer2[2];
+
+	u8 *rx_buffer;
+	u32 buffer_size;
+	u8 sync;
+
+	struct qcafrm_handle frm_handle;
+	struct sk_buff *rx_skb;
+
+	unsigned int intr_req;
+	unsigned int intr_svc;
+
+#ifdef CONFIG_DEBUG_FS
+	struct dentry *device_root;
+#endif
+
+	/* user configurable options */
+	u32 clkspeed;
+	u8 legacy_mode;
+	u16 burst_len;
+};
+
+int qcaspi_netdev_open(struct net_device *dev);
+int qcaspi_netdev_close(struct net_device *dev);
+
+#endif /* _QCA_SPI_H */