ASoC: sirf: Add audio usp interface driver

This patch adds ASoC support for SiRF SoCs USP interface.
Features include:
1. Only support slave mode.
2. Support I2S and DSP_A mode.
3. Support S16_LE, S24_LE and S24_3LE formats.
4. Support stereo and mono mode.
5. The biggest Support is 192Khz sample rate.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

sound/soc/sirf/Kconfig

@@ -12,3 +12,9 @@ config SND_SOC_SIRF_AUDIO
 config SND_SOC_SIRF_AUDIO_PORT
 	select REGMAP_MMIO
 	tristate
+
+config SND_SOC_SIRF_USP
+	tristate "SoC Audio (I2S protocol) for SiRF SoC USP interface"
+	depends on SND_SOC_SIRF
+	select REGMAP_MMIO
+	tristate

sound/soc/sirf/Makefile

 snd-soc-sirf-audio-objs := sirf-audio.o
 snd-soc-sirf-audio-port-objs := sirf-audio-port.o
+snd-soc-sirf-usp-objs := sirf-usp.o
 
 obj-$(CONFIG_SND_SOC_SIRF_AUDIO) += snd-soc-sirf-audio.o
 obj-$(CONFIG_SND_SOC_SIRF_AUDIO_PORT) += snd-soc-sirf-audio-port.o
+obj-$(CONFIG_SND_SOC_SIRF_USP) += snd-soc-sirf-usp.o

sound/soc/sirf/sirf-usp.h

+/*
+ * arch/arm/mach-prima2/include/mach/sirfsoc_usp.h
+ *
+ * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#ifndef _SIRF_USP_H
+#define _SIRF_USP_H
+
+/* USP Registers */
+#define USP_MODE1		0x00
+#define USP_MODE2		0x04
+#define USP_TX_FRAME_CTRL	0x08
+#define USP_RX_FRAME_CTRL	0x0C
+#define USP_TX_RX_ENABLE	0x10
+#define USP_INT_ENABLE		0x14
+#define USP_INT_STATUS		0x18
+#define USP_PIN_IO_DATA		0x1C
+#define USP_RISC_DSP_MODE	0x20
+#define USP_AYSNC_PARAM_REG	0x24
+#define USP_IRDA_X_MODE_DIV	0x28
+#define USP_SM_CFG		0x2C
+#define USP_TX_DMA_IO_CTRL	0x100
+#define USP_TX_DMA_IO_LEN	0x104
+#define USP_TX_FIFO_CTRL	0x108
+#define USP_TX_FIFO_LEVEL_CHK	0x10C
+#define USP_TX_FIFO_OP		0x110
+#define USP_TX_FIFO_STATUS	0x114
+#define USP_TX_FIFO_DATA	0x118
+#define USP_RX_DMA_IO_CTRL	0x120
+#define USP_RX_DMA_IO_LEN	0x124
+#define USP_RX_FIFO_CTRL	0x128
+#define USP_RX_FIFO_LEVEL_CHK	0x12C
+#define USP_RX_FIFO_OP		0x130
+#define USP_RX_FIFO_STATUS	0x134
+#define USP_RX_FIFO_DATA	0x138
+
+/* USP MODE register-1 */
+#define USP_SYNC_MODE			0x00000001
+#define USP_CLOCK_MODE_SLAVE		0x00000002
+#define USP_LOOP_BACK_EN		0x00000004
+#define USP_HPSIR_EN			0x00000008
+#define USP_ENDIAN_CTRL_LSBF		0x00000010
+#define USP_EN				0x00000020
+#define USP_RXD_ACT_EDGE_FALLING	0x00000040
+#define USP_TXD_ACT_EDGE_FALLING	0x00000080
+#define USP_RFS_ACT_LEVEL_LOGIC1	0x00000100
+#define USP_TFS_ACT_LEVEL_LOGIC1	0x00000200
+#define USP_SCLK_IDLE_MODE_TOGGLE	0x00000400
+#define USP_SCLK_IDLE_LEVEL_LOGIC1	0x00000800
+#define USP_SCLK_PIN_MODE_IO	0x00001000
+#define USP_RFS_PIN_MODE_IO	0x00002000
+#define USP_TFS_PIN_MODE_IO	0x00004000
+#define USP_RXD_PIN_MODE_IO	0x00008000
+#define USP_TXD_PIN_MODE_IO	0x00010000
+#define USP_SCLK_IO_MODE_INPUT	0x00020000
+#define USP_RFS_IO_MODE_INPUT	0x00040000
+#define USP_TFS_IO_MODE_INPUT	0x00080000
+#define USP_RXD_IO_MODE_INPUT	0x00100000
+#define USP_TXD_IO_MODE_INPUT	0x00200000
+#define USP_IRDA_WIDTH_DIV_MASK	0x3FC00000
+#define USP_IRDA_WIDTH_DIV_OFFSET	0
+#define USP_IRDA_IDLE_LEVEL_HIGH	0x40000000
+#define USP_TX_UFLOW_REPEAT_ZERO	0x80000000
+#define USP_TX_ENDIAN_MODE		0x00000020
+#define USP_RX_ENDIAN_MODE		0x00000020
+
+/* USP Mode Register-2 */
+#define USP_RXD_DELAY_LEN_MASK		0x000000FF
+#define USP_RXD_DELAY_LEN_OFFSET	0
+
+#define USP_TXD_DELAY_LEN_MASK		0x0000FF00
+#define USP_TXD_DELAY_LEN_OFFSET	8
+
+#define USP_ENA_CTRL_MODE		0x00010000
+#define USP_FRAME_CTRL_MODE		0x00020000
+#define USP_TFS_SOURCE_MODE             0x00040000
+#define USP_TFS_MS_MODE                 0x00080000
+#define USP_CLK_DIVISOR_MASK		0x7FE00000
+#define USP_CLK_DIVISOR_OFFSET		21
+
+#define USP_TFS_CLK_SLAVE_MODE		(1<<20)
+#define USP_RFS_CLK_SLAVE_MODE		(1<<19)
+
+#define USP_IRDA_DATA_WIDTH		0x80000000
+
+/* USP Transmit Frame Control Register */
+
+#define USP_TXC_DATA_LEN_MASK		0x000000FF
+#define USP_TXC_DATA_LEN_OFFSET		0
+
+#define USP_TXC_SYNC_LEN_MASK		0x0000FF00
+#define USP_TXC_SYNC_LEN_OFFSET		8
+
+#define USP_TXC_FRAME_LEN_MASK		0x00FF0000
+#define USP_TXC_FRAME_LEN_OFFSET	16
+
+#define USP_TXC_SHIFTER_LEN_MASK	0x1F000000
+#define USP_TXC_SHIFTER_LEN_OFFSET	24
+
+#define USP_TXC_SLAVE_CLK_SAMPLE	0x20000000
+
+#define USP_TXC_CLK_DIVISOR_MASK	0xC0000000
+#define USP_TXC_CLK_DIVISOR_OFFSET	30
+
+/* USP Receive Frame Control Register */
+
+#define USP_RXC_DATA_LEN_MASK		0x000000FF
+#define USP_RXC_DATA_LEN_OFFSET		0
+
+#define USP_RXC_FRAME_LEN_MASK		0x0000FF00
+#define USP_RXC_FRAME_LEN_OFFSET	8
+
+#define USP_RXC_SHIFTER_LEN_MASK	0x001F0000
+#define USP_RXC_SHIFTER_LEN_OFFSET	16
+
+#define USP_START_EDGE_MODE	0x00800000
+#define USP_I2S_SYNC_CHG	0x00200000
+
+#define USP_RXC_CLK_DIVISOR_MASK	0x0F000000
+#define USP_RXC_CLK_DIVISOR_OFFSET	24
+#define USP_SINGLE_SYNC_MODE		0x00400000
+
+/* Tx - RX Enable Register */
+
+#define USP_RX_ENA		0x00000001
+#define USP_TX_ENA		0x00000002
+
+/* USP Interrupt Enable and status Register */
+#define USP_RX_DONE_INT			0x00000001
+#define USP_TX_DONE_INT			0x00000002
+#define USP_RX_OFLOW_INT		0x00000004
+#define USP_TX_UFLOW_INT		0x00000008
+#define USP_RX_IO_DMA_INT		0x00000010
+#define USP_TX_IO_DMA_INT		0x00000020
+#define USP_RXFIFO_FULL_INT		0x00000040
+#define USP_TXFIFO_EMPTY_INT		0x00000080
+#define USP_RXFIFO_THD_INT		0x00000100
+#define USP_TXFIFO_THD_INT		0x00000200
+#define USP_UART_FRM_ERR_INT		0x00000400
+#define USP_RX_TIMEOUT_INT		0x00000800
+#define USP_TX_ALLOUT_INT		0x00001000
+#define USP_RXD_BREAK_INT		0x00008000
+
+/* All possible TX interruots */
+#define USP_TX_INTERRUPT		(USP_TX_DONE_INT|USP_TX_UFLOW_INT|\
+					USP_TX_IO_DMA_INT|\
+					USP_TXFIFO_EMPTY_INT|\
+					USP_TXFIFO_THD_INT)
+/* All possible RX interruots */
+#define USP_RX_INTERRUPT		(USP_RX_DONE_INT|USP_RX_OFLOW_INT|\
+					USP_RX_IO_DMA_INT|\
+					USP_RXFIFO_FULL_INT|\
+					USP_RXFIFO_THD_INT|\
+					USP_RXFIFO_THD_INT|USP_RX_TIMEOUT_INT)
+
+#define USP_INT_ALL        0x1FFF
+
+/* USP Pin I/O Data Register */
+
+#define USP_RFS_PIN_VALUE_MASK	0x00000001
+#define USP_TFS_PIN_VALUE_MASK	0x00000002
+#define USP_RXD_PIN_VALUE_MASK	0x00000004
+#define USP_TXD_PIN_VALUE_MASK	0x00000008
+#define USP_SCLK_PIN_VALUE_MASK	0x00000010
+
+/* USP RISC/DSP Mode Register */
+#define USP_RISC_DSP_SEL	0x00000001
+
+/* USP ASYNC PARAMETER Register*/
+
+#define USP_ASYNC_TIMEOUT_MASK	0x0000FFFF
+#define USP_ASYNC_TIMEOUT_OFFSET	0
+#define USP_ASYNC_TIMEOUT(x)	(((x)&USP_ASYNC_TIMEOUT_MASK) \
+				<<USP_ASYNC_TIMEOUT_OFFSET)
+
+#define USP_ASYNC_DIV2_MASK		0x003F0000
+#define USP_ASYNC_DIV2_OFFSET		16
+
+/* USP TX DMA I/O MODE Register */
+#define USP_TX_MODE_IO			0x00000001
+
+/* USP TX DMA I/O Length Register */
+#define USP_TX_DATA_LEN_MASK		0xFFFFFFFF
+#define USP_TX_DATA_LEN_OFFSET		0
+
+/* USP TX FIFO Control Register */
+#define USP_TX_FIFO_WIDTH_MASK		0x00000003
+#define USP_TX_FIFO_WIDTH_OFFSET	0
+
+#define USP_TX_FIFO_THD_MASK		0x000001FC
+#define USP_TX_FIFO_THD_OFFSET		2
+
+/* USP TX FIFO Level Check Register */
+#define USP_TX_FIFO_LEVEL_CHECK_MASK	0x1F
+#define USP_TX_FIFO_SC_OFFSET	0
+#define USP_TX_FIFO_LC_OFFSET	10
+#define USP_TX_FIFO_HC_OFFSET	20
+
+#define TX_FIFO_SC(x)		(((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_TX_FIFO_SC_OFFSET)
+#define TX_FIFO_LC(x)		(((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_TX_FIFO_LC_OFFSET)
+#define TX_FIFO_HC(x)		(((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_TX_FIFO_HC_OFFSET)
+
+/* USP TX FIFO Operation Register */
+#define USP_TX_FIFO_RESET		0x00000001
+#define USP_TX_FIFO_START		0x00000002
+
+/* USP TX FIFO Status Register */
+#define USP_TX_FIFO_LEVEL_MASK		0x0000007F
+#define USP_TX_FIFO_LEVEL_OFFSET	0
+
+#define USP_TX_FIFO_FULL		0x00000080
+#define USP_TX_FIFO_EMPTY		0x00000100
+
+/* USP TX FIFO Data Register */
+#define USP_TX_FIFO_DATA_MASK		0xFFFFFFFF
+#define USP_TX_FIFO_DATA_OFFSET		0
+
+/* USP RX DMA I/O MODE Register */
+#define USP_RX_MODE_IO			0x00000001
+#define USP_RX_DMA_FLUSH		0x00000004
+
+/* USP RX DMA I/O Length Register */
+#define USP_RX_DATA_LEN_MASK		0xFFFFFFFF
+#define USP_RX_DATA_LEN_OFFSET		0
+
+/* USP RX FIFO Control Register */
+#define USP_RX_FIFO_WIDTH_MASK		0x00000003
+#define USP_RX_FIFO_WIDTH_OFFSET	0
+
+#define USP_RX_FIFO_THD_MASK		0x000001FC
+#define USP_RX_FIFO_THD_OFFSET		2
+
+/* USP RX FIFO Level Check Register */
+
+#define USP_RX_FIFO_LEVEL_CHECK_MASK	0x1F
+#define USP_RX_FIFO_SC_OFFSET	0
+#define USP_RX_FIFO_LC_OFFSET	10
+#define USP_RX_FIFO_HC_OFFSET	20
+
+#define RX_FIFO_SC(x)		(((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_RX_FIFO_SC_OFFSET)
+#define RX_FIFO_LC(x)		(((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_RX_FIFO_LC_OFFSET)
+#define RX_FIFO_HC(x)		(((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) \
+				<< USP_RX_FIFO_HC_OFFSET)
+
+/* USP RX FIFO Operation Register */
+#define USP_RX_FIFO_RESET		0x00000001
+#define USP_RX_FIFO_START		0x00000002
+
+/* USP RX FIFO Status Register */
+
+#define USP_RX_FIFO_LEVEL_MASK		0x0000007F
+#define USP_RX_FIFO_LEVEL_OFFSET	0
+
+#define USP_RX_FIFO_FULL		0x00000080
+#define USP_RX_FIFO_EMPTY		0x00000100
+
+/* USP RX FIFO Data Register */
+
+#define USP_RX_FIFO_DATA_MASK		0xFFFFFFFF
+#define USP_RX_FIFO_DATA_OFFSET		0
+
+/*
+ * When rx thd irq occur, sender just disable tx empty irq,
+ * Remaining data in tx fifo wil also be sent out.
+ */
+#define USP_FIFO_SIZE			128
+#define USP_TX_FIFO_THRESHOLD		(USP_FIFO_SIZE/2)
+#define USP_RX_FIFO_THRESHOLD		(USP_FIFO_SIZE/2)
+
+/* FIFO_WIDTH for the USP_TX_FIFO_CTRL and USP_RX_FIFO_CTRL registers */
+#define USP_FIFO_WIDTH_BYTE  0x00
+#define USP_FIFO_WIDTH_WORD  0x01
+#define USP_FIFO_WIDTH_DWORD 0x02
+
+#define USP_ASYNC_DIV2          16
+
+#define USP_PLUGOUT_RETRY_CNT	2
+
+#define USP_TX_RX_FIFO_WIDTH_DWORD    2
+
+#define SIRF_USP_DIV_MCLK	0
+
+#define SIRF_USP_I2S_TFS_SYNC	0
+#define SIRF_USP_I2S_RFS_SYNC	1
+#endif