[PATCH] console_setup() depends (wrongly?) on CONFIG_PRINTK

It appears that console_setup() code only gets compiled into the kernel if
CONFIG_PRINTK is enabled.  One detrimental side-effect of this is that
serial8250_console_setup() never gets invoked when CONFIG_PRINTK is not
set, resulting in baud rate not being read/parsed from command line (i.e.
console=ttyS0,115200n8 is ignored, at least the baud rate part...)

Attached patch moves console_setup() code from inside

#ifdef CONFIG_PRINTK

to outside (in printk.c), removing dependence on said config. option.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

kernel/printk.c

@@ -122,44 +122,6 @@ static char *log_buf = __log_buf;
 static int log_buf_len = __LOG_BUF_LEN;
 static unsigned long logged_chars; /* Number of chars produced since last read+clear operation */
 
-/*
- *	Setup a list of consoles. Called from init/main.c
- */
-static int __init console_setup(char *str)
-{
-	char name[sizeof(console_cmdline[0].name)];
-	char *s, *options;
-	int idx;
-
-	/*
-	 *	Decode str into name, index, options.
-	 */
-	if (str[0] >= '0' && str[0] <= '9') {
-		strcpy(name, "ttyS");
-		strncpy(name + 4, str, sizeof(name) - 5);
-	} else
-		strncpy(name, str, sizeof(name) - 1);
-	name[sizeof(name) - 1] = 0;
-	if ((options = strchr(str, ',')) != NULL)
-		*(options++) = 0;
-#ifdef __sparc__
-	if (!strcmp(str, "ttya"))
-		strcpy(name, "ttyS0");
-	if (!strcmp(str, "ttyb"))
-		strcpy(name, "ttyS1");
-#endif
-	for (s = name; *s; s++)
-		if ((*s >= '0' && *s <= '9') || *s == ',')
-			break;
-	idx = simple_strtoul(s, NULL, 10);
-	*s = 0;
-
-	add_preferred_console(name, idx, options);
-	return 1;
-}
-
-__setup("console=", console_setup);
-
 static int __init log_buf_len_setup(char *str)
 {
 	unsigned long size = memparse(str, &str);
@@ -659,6 +621,44 @@ static void call_console_drivers(unsigned long start, unsigned long end)
 
 #endif
 
+/*
+ * Set up a list of consoles.  Called from init/main.c
+ */
+static int __init console_setup(char *str)
+{
+	char name[sizeof(console_cmdline[0].name)];
+	char *s, *options;
+	int idx;
+
+	/*
+	 * Decode str into name, index, options.
+	 */
+	if (str[0] >= '0' && str[0] <= '9') {
+		strcpy(name, "ttyS");
+		strncpy(name + 4, str, sizeof(name) - 5);
+	} else {
+		strncpy(name, str, sizeof(name) - 1);
+	}
+	name[sizeof(name) - 1] = 0;
+	if ((options = strchr(str, ',')) != NULL)
+		*(options++) = 0;
+#ifdef __sparc__
+	if (!strcmp(str, "ttya"))
+		strcpy(name, "ttyS0");
+	if (!strcmp(str, "ttyb"))
+		strcpy(name, "ttyS1");
+#endif
+	for (s = name; *s; s++)
+		if ((*s >= '0' && *s <= '9') || *s == ',')
+			break;
+	idx = simple_strtoul(s, NULL, 10);
+	*s = 0;
+
+	add_preferred_console(name, idx, options);
+	return 1;
+}
+__setup("console=", console_setup);
+
 /**
  * add_preferred_console - add a device to the list of preferred consoles.
  * @name: device name