[SCSI] qla2xxx: Correct ISP24xx soft-reset handling.

A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated.  A
similar delay was needed with earlier ISPs.

Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

drivers/scsi/qla2xxx/qla_dbg.c

@@ -970,7 +970,7 @@ qla24xx_fw_dump(scsi_qla_host_t *ha, int hardware_locked)
 	int		rval;
 	uint32_t	cnt, timer;
 	uint32_t	risc_address;
-	uint16_t	mb[4];
+	uint16_t	mb[4], wd;
 
 	uint32_t	stat;
 	struct device_reg_24xx __iomem *reg = &ha->iobase->isp24;
@@ -1514,10 +1514,10 @@ qla24xx_fw_dump(scsi_qla_host_t *ha, int hardware_locked)
 
 		WRT_REG_DWORD(&reg->ctrl_status,
 		    CSRX_ISP_SOFT_RESET|CSRX_DMA_SHUTDOWN|MWB_4096_BYTES);
-		RD_REG_DWORD(&reg->ctrl_status);
+		pci_read_config_word(ha->pdev, PCI_COMMAND, &wd);
 
+		udelay(100);
 		/* Wait for firmware to complete NVRAM accesses. */
-		udelay(5);
 		mb[0] = (uint32_t) RD_REG_WORD(&reg->mailbox0);
 		for (cnt = 10000 ; cnt && mb[0]; cnt--) {
 			udelay(5);
@@ -1525,7 +1525,7 @@ qla24xx_fw_dump(scsi_qla_host_t *ha, int hardware_locked)
 			barrier();
 		}
 
-		udelay(20);
+		/* Wait for soft-reset to complete. */
 		for (cnt = 0; cnt < 30000; cnt++) {
 			if ((RD_REG_DWORD(&reg->ctrl_status) &
 			    CSRX_ISP_SOFT_RESET) == 0)

drivers/scsi/qla2xxx/qla_init.c

@@ -567,6 +567,7 @@ qla24xx_reset_risc(scsi_qla_host_t *ha)
 	unsigned long flags = 0;
 	struct device_reg_24xx __iomem *reg = &ha->iobase->isp24;
 	uint32_t cnt, d2;
+	uint16_t wd;
 
 	spin_lock_irqsave(&ha->hardware_lock, flags);
 
@@ -581,10 +582,10 @@ qla24xx_reset_risc(scsi_qla_host_t *ha)
 
 	WRT_REG_DWORD(&reg->ctrl_status,
 	    CSRX_ISP_SOFT_RESET|CSRX_DMA_SHUTDOWN|MWB_4096_BYTES);
-	RD_REG_DWORD(&reg->ctrl_status);
+	pci_read_config_word(ha->pdev, PCI_COMMAND, &wd);
 
+	udelay(100);
 	/* Wait for firmware to complete NVRAM accesses. */
-	udelay(5);
 	d2 = (uint32_t) RD_REG_WORD(&reg->mailbox0);
 	for (cnt = 10000 ; cnt && d2; cnt--) {
 		udelay(5);
@@ -592,7 +593,7 @@ qla24xx_reset_risc(scsi_qla_host_t *ha)
 		barrier();
 	}
 
-	udelay(20);
+	/* Wait for soft-reset to complete. */
 	d2 = RD_REG_DWORD(&reg->ctrl_status);
 	for (cnt = 6000000 ; cnt && (d2 & CSRX_ISP_SOFT_RESET); cnt--) {
 		udelay(5);