Merge branch 'libertas-fixes' of...

Merge branch 'libertas-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes

drivers/net/wireless/libertas/Makefile

@@ -2,7 +2,7 @@ libertas-objs := main.o fw.o wext.o \
 		rx.o tx.o cmd.o 	  \
 		cmdresp.o scan.o	  \
 		join.o 11d.o 		  \
-		ioctl.o debugfs.o	  \
+		debugfs.o	  \
 		ethtool.o assoc.o
 
 usb8xxx-objs += if_bootcmd.o

drivers/net/wireless/libertas/README

@@ -28,281 +28,6 @@ DRIVER LOADING
 
 		insmod usb8388.ko [fw_name=usb8388.bin]
 
-=====================
-IWPRIV COMMAND
-=====================
-
-NAME
-	This manual describes the usage of private commands used in Marvell WLAN
-	Linux Driver. All the commands available in Wlanconfig will not be available
-	in the iwpriv.
-
-SYNOPSIS
-	iwpriv <ethX> <command> [sub-command] ...
-
-	iwpriv ethX setregioncode <n>
-	iwpriv ethX getregioncode
-
-Version 5 Command:
-	iwpriv ethX ledgpio <n>
-
-BT Commands:
-	The blinding table (BT) contains a list of mac addresses that will be,
-	by default, ignored by the firmware. It is also possible to invert this
-	behavior so that we will ignore all traffic except for the portion
-	coming from mac addresess in the list. It is primarily used for
-	debugging and testing networks.  It can be edited and inspected with
-	the following commands:
-
-	iwpriv ethX bt_reset
-	iwpriv ethX bt_add <mac_address>
-	iwpriv ethX bt_del <mac_address>
-	iwpriv ethX bt_list <id>
-	iwpriv ethX bt_get_invert <n>
-	iwpriv ethX bt_set_invert <n>
-
-FWT Commands:
-	The forwarding table (FWT) is a feature used to manage mesh network
-	routing in the firmware.  The FWT is essentially a routing table that
-	associates a destination mac address (da) with a next hop receiver
-	address (ra).  The FWT can be inspected and edited with the following
-	iwpriv commands, which are described in greater detail below.
-	Eventually, the table will be automatically maintained by a custom
-	routing protocol.
-
-	NOTE: FWT commands replace the previous DFT commands.  What were the DFT
-	commands?, you might ask.  They were an earlier API to the firmware that
-	implemented a simple MAC-layer forwarding mechanism.  In the unlikely
-	event that you were using these commands, you must migrate to the new
-	FWT commands which can be used to achieve the same functionality.
-
-	iwpriv ethX fwt_add [parameters]
-	iwpriv ethX fwt_del [parameters]
-	iwpriv ethX fwt_lookup [parameters]
-	iwpriv ethX fwt_list [parameters]
-	iwpriv ethX fwt_list_route [parameters]
-	iwpriv ethX fwt_list_neigh [parameters]
-	iwpriv ethX fwt_reset [parameters]
-	iwpriv ethX fwt_cleanup
-	iwpriv ethX fwt_time
-
-MESH Commands:
-
-	The MESH commands are used to configure various features of the mesh
-	routing protocol.  The following commands are supported:
-
-	iwpriv ethX mesh_get_ttl
-	iwpriv ethX mesh_set_ttl ttl
-
-DESCRIPTION
-	Those commands are used to send additional commands to the Marvell WLAN
-	card via the Linux device driver.
-
-	The ethX parameter specifies the network device that is to be used to
-		perform this command on. it could be eth0, eth1 etc.
-
-setregioncode
-	This command is used to set the region code in the station.
-	where value is 'region code' for various regions like
-	USA FCC, Canada IC, Spain, France, Europe ETSI,	Japan ...
-
-	Usage:
-		iwpriv ethX setregioncode 0x10: set region code to USA (0x10).
-
-getregioncode
-	This command is used to get the region code information set in the
-	station.
-
-ledgpio
-	This command is used to set/get LEDs.
-
-	iwpriv ethX ledgpio <LEDs>
-		will set the corresponding LED for the GPIO Line.
-
-	iwpriv ethX ledgpio
-		will give u which LEDs are Enabled.
-
-	Usage:
-		iwpriv eth1 ledgpio 1 0 2 1 3 4
-			will enable
-			LED 1 -> GPIO 0
-			LED 2 -> GPIO 1
-			LED 3 -> GPIO 4
-
-		iwpriv eth1 ledgpio
-			shows LED information in the format as mentioned above.
-
-	Note: LED0 is invalid
-	Note: Maximum Number of LEDs are 16.
-
-fwt_add
-	This command is used to insert an entry into the FWT table. The list of
-	parameters must follow the following structure:
-
-	iwpriv ethX fwt_add da ra [metric dir rate ssn dsn hopcount ttl expiration sleepmode snr]
-
-	The parameters between brackets are optional, but they must appear in
-	the order specified.  For example, if you want to specify the metric,
-	you must also specify the dir, ssn, and dsn but you need not specify the
-	hopcount, expiration, sleepmode, or snr.  Any unspecified parameters
-	will be assigned the defaults specified below.
-
-	The different parameters are:-
-		da		-- DA MAC address in the form 00:11:22:33:44:55
-		ra		-- RA MAC address in the form 00:11:22:33:44:55
-		metric		-- route metric (cost: smaller-metric routes are
-				   preferred, default is 0)
-		dir		-- direction (1 for direct, 0 for reverse,
-				   default is 1)
-		rate		-- data rate used for transmission to the RA,
-				   as specified for the rateadapt command,
-				   default is 3 (11Mbps)
-		ssn		-- Source Sequence Number (time at the RA for
-				   reverse routes.  Default is 0)
-		dsn		-- Destination Sequence Number (time at the DA
-				   for direct routes.  Default is 0)
-		hopcount	-- hop count (currently unused, default is 0)
-		ttl		-- TTL (Only used in reverse entries)
-		expiration	-- entry expiration (in ticks, where a tick is
-				   1024us, or ~ 1ms. Use 0 for an indefinite
-				   entry, default is 0)
-		sleepmode	-- RA's sleep mode (currently unused, default is
-				   0)
-		snr		-- SNR in the link to RA (currently unused,
-				   default is 0)
-
-	The command does not return anything.
-
-fwt_del
-	This command is used to remove an entry to the FWT table. The list of
-	parameters must follow the following structure:
-
-		iwpriv ethX fwt_del da ra [dir]
-
-	where the different parameters are:-
-		da		-- DA MAC address (in the form "00:11:22:33:44:55")
-		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
-		dir		-- direction (1 for direct, 0 for reverse,
-				   default is 1)
-
-	The command does not return anything.
-
-fwt_lookup
-	This command is used to get the best route in the FWT table to a given
-	host. The only parameter is the MAC address of the host that is being
-	looked for.
-
-		iwpriv ethX fwt_lookup da
-
-	where:-
-		da		-- DA MAC address (in the form "00:11:22:33:44:55")
-
-	The command returns an output string identical to the one returned by
-	fwt_list described below.
-
-
-fwt_list
-	This command is used to list a route from the FWT table. The only
-	parameter is the index into the table. If you want to list all the
-	routes in a table, start with index=0, and keep listing until you get a
-	"(null)" string.  Note that the indicies may change as the fwt is
-	updated.  It is expected that most users will not use fwt_list directly,
-	but that a utility similar to the traditional route command will be used
-	to invoke fwt_list over and over.
-
-		iwpriv ethX fwt_list index
-
-	The output is a string of the following form:
-
-		da ra valid metric dir rate ssn dsn hopcount ttl expiration
-		sleepmode snr precursor
-
-	where the different fields are:-
-		da		-- DA MAC address (in the form "00:11:22:33:44:55")
-		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
-		valid		-- whether the route is valid (0 if not valid)
-		metric		-- route metric (cost: smaller-metric routes are preferred)
-		dir		-- direction (1 for direct, 0 for reverse)
-		rate		-- data rate used for transmission to the RA,
-				   as specified for the rateadapt command
-		ssn		-- Source Sequence Number (time at the RA for reverse routes)
-		dsn		-- Destination Sequence Number (time at the DA for direct routes)
-		hopcount	-- hop count (currently unused)
-		ttl		-- TTL (only used in reverse entries)
-		expiration	-- entry expiration (in ticks, where a tick is 1024us, or ~ 1ms. Use 0 for an indefinite entry)
-		sleepmode	-- RA's sleep mode (currently unused)
-		snr		-- SNR in the link to RA (currently unused)
-		precursor	-- predecessor in direct routes
-
-fwt_list_route
-	This command is equivalent to fwt_list.
-
-fwt_list_neigh
-	This command is used to list a neighbor from the FWT table. The only
-	parameter is the neighbor ID. If you want to list all the neighbors in a
-	table, start with nid=0, and keep incrementing nid until you get a
-	"(null)" string.  Note that the nid from a fwt_list_route command can be
-	used as an input to this command.  Also note that this command is meant
-	mostly for debugging.  It is expected that users will use fwt_lookup.
-	One important reason for this is that the neighbor id may change as the
-	neighbor table is altered.
-
-		iwpriv ethX fwt_list_neigh nid
-
-	The output is a string of the following form:
-
-		ra sleepmode snr references
-
-	where the different fields are:-
-		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
-		sleepmode	-- RA's sleep mode (currently unused)
-		snr		-- SNR in the link to RA (currently unused)
-		references	-- RA's reference counter
-
-fwt_reset
-	This command is used to reset the FWT table, getting rid of all the
-	entries. There are no input parameters.
-
-		iwpriv ethX fwt_reset
-
-	The command does not return anything.
-
-fwt_cleanup
-	This command is used to perform user-based garbage recollection. The
-	FWT table is checked, and all the entries that are expired or invalid
-	are cleaned. Note that this is exported to the driver for debugging
-	purposes, as garbage collection is also fired by the firmware when in
-	space problems. There are no input parameters.
-
-		iwpriv ethX fwt_cleanup
-
-	The command does returns the number of invalid/expired routes deleted.
-
-fwt_time
-	This command returns a card's internal time representation.  It is this
-	time that is used to represent the expiration times of FWT entries.  The
-	number is not consistent from card to card; it is simply a timer count.
-	The fwt_time command is used to inspect the timer so that expiration
-	times reported by fwt_list can be properly interpreted.
-
-		iwpriv ethX fwt_time
-
-mesh_get_ttl
-
-	The mesh ttl is the number of hops a mesh packet can traverse before it
-	is dropped.  This parameter is used to prevent infinite loops in the
-	mesh network.  The value returned by this function is the ttl assigned
-	to all mesh packets.  Currently there is no way to control the ttl on a
-	per packet or per socket basis.
-
-	iwpriv ethX mesh_get_ttl
-
-mesh_set_ttl ttl
-
-	Set the ttl.  The argument must be between 0 and 255.
-
-	iwpriv ethX mesh_set_ttl <ttl>
-
 =========================
 ETHTOOL
 =========================

drivers/net/wireless/libertas/assoc.c

@@ -323,6 +323,8 @@ static int assoc_helper_secinfo(wlan_private *priv,
 {
 	wlan_adapter *adapter = priv->adapter;
 	int ret = 0;
+	u32 do_wpa;
+	u32 rsn = 0;
 
 	lbs_deb_enter(LBS_DEB_ASSOC);
 
@@ -333,12 +335,34 @@ static int assoc_helper_secinfo(wlan_private *priv,
 	if (ret)
 		goto out;
 
-	/* enable/disable RSN */
+	/* If RSN is already enabled, don't try to enable it again, since
+	 * ENABLE_RSN resets internal state machines and will clobber the
+	 * 4-way WPA handshake.
+	 */
+
+	/* Get RSN enabled/disabled */
 	ret = libertas_prepare_and_send_command(priv,
 				    cmd_802_11_enable_rsn,
 				    cmd_act_set,
 				    cmd_option_waitforrsp,
-				    0, assoc_req);
+				    0, &rsn);
+	if (ret) {
+		lbs_deb_assoc("Failed to get RSN status: %d", ret);
+		goto out;
+	}
+
+	/* Don't re-enable RSN if it's already enabled */
+	do_wpa = (assoc_req->secinfo.WPAenabled || assoc_req->secinfo.WPA2enabled);
+	if (do_wpa == rsn)
+		goto out;
+
+	/* Set RSN enabled/disabled */
+	rsn = do_wpa;
+	ret = libertas_prepare_and_send_command(priv,
+				    cmd_802_11_enable_rsn,
+				    cmd_act_set,
+				    cmd_option_waitforrsp,
+				    0, &rsn);
 
 out:
 	lbs_deb_leave_args(LBS_DEB_ASSOC, "ret %d", ret);

drivers/net/wireless/libertas/cmd.c

@@ -228,17 +228,19 @@ static int wlan_cmd_802_11_enable_rsn(wlan_private * priv,
 				      void * pdata_buf)
 {
 	struct cmd_ds_802_11_enable_rsn *penableRSN = &cmd->params.enbrsn;
-	struct assoc_request * assoc_req = pdata_buf;
+	u32 * enable = pdata_buf;
 
 	lbs_deb_enter(LBS_DEB_CMD);
 
 	cmd->command = cpu_to_le16(cmd_802_11_enable_rsn);
 	cmd->size = cpu_to_le16(sizeof(*penableRSN) + S_DS_GEN);
 	penableRSN->action = cpu_to_le16(cmd_action);
-	if (assoc_req->secinfo.WPAenabled || assoc_req->secinfo.WPA2enabled) {
+
+	if (cmd_action == cmd_act_set) {
+		if (*enable)
+			penableRSN->enable = cpu_to_le16(cmd_enable_rsn);
+		else
 			penableRSN->enable = cpu_to_le16(cmd_enable_rsn);
-	} else {
-		penableRSN->enable = cpu_to_le16(cmd_disable_rsn);
 	}
 
 	lbs_deb_leave(LBS_DEB_CMD);

drivers/net/wireless/libertas/cmdresp.c

@@ -537,6 +537,24 @@ static int wlan_ret_get_log(wlan_private * priv,
 	return 0;
 }
 
+static int libertas_ret_802_11_enable_rsn(wlan_private * priv,
+                                          struct cmd_ds_command *resp)
+{
+	struct cmd_ds_802_11_enable_rsn *enable_rsn = &resp->params.enbrsn;
+	wlan_adapter *adapter = priv->adapter;
+	u32 * pdata_buf = adapter->cur_cmd->pdata_buf;
+
+	lbs_deb_enter(LBS_DEB_CMD);
+
+	if (enable_rsn->action == cpu_to_le16(cmd_act_get)) {
+		if (pdata_buf)
+			*pdata_buf = (u32) le16_to_cpu(enable_rsn->enable);
+	}
+
+	lbs_deb_enter(LBS_DEB_CMD);
+	return 0;
+}
+
 static inline int handle_cmd_response(u16 respcmd,
 				      struct cmd_ds_command *resp,
 				      wlan_private *priv)
@@ -610,7 +628,10 @@ static inline int handle_cmd_response(u16 respcmd,
 	case cmd_ret_802_11_authenticate:
 	case cmd_ret_802_11_radio_control:
 	case cmd_ret_802_11_beacon_stop:
+		break;
+
 	case cmd_ret_802_11_enable_rsn:
+		ret = libertas_ret_802_11_enable_rsn(priv, resp);
 		break;
 
 	case cmd_ret_802_11_data_rate:

drivers/net/wireless/libertas/hostcmd.h

@@ -503,7 +503,7 @@ struct cmd_ds_802_11_ad_hoc_join {
 struct cmd_ds_802_11_enable_rsn {
 	__le16 action;
 	__le16 enable;
-};
+} __attribute__ ((packed));
 
 struct MrvlIEtype_keyParamSet {
 	/* type ID */

drivers/net/wireless/libertas/main.c

@@ -181,7 +181,8 @@ u16 libertas_region_code_to_index[MRVDRV_MAX_REGION_CODE] =
  * @brief Get function for sysfs attribute anycast_mask
  */
 static ssize_t libertas_anycast_get(struct device * dev,
-		struct device_attribute *attr, char * buf) {
+		struct device_attribute *attr, char * buf)
+{
 	struct cmd_ds_mesh_access mesh_access;
 
 	memset(&mesh_access, 0, sizeof(mesh_access));
@@ -197,7 +198,8 @@ static ssize_t libertas_anycast_get(struct device * dev,
  * @brief Set function for sysfs attribute anycast_mask
  */
 static ssize_t libertas_anycast_set(struct device * dev,
-		struct device_attribute *attr, const char * buf, size_t count) {
+		struct device_attribute *attr, const char * buf, size_t count)
+{
 	struct cmd_ds_mesh_access mesh_access;
 	uint32_t datum;
 
@@ -799,7 +801,6 @@ wlan_private *libertas_add_card(void *card, struct device *dmdev)
 	dev->open = wlan_open;
 	dev->hard_start_xmit = wlan_pre_start_xmit;
 	dev->stop = wlan_close;
-	dev->do_ioctl = libertas_do_ioctl;
 	dev->set_mac_address = wlan_set_mac_address;
 	dev->tx_timeout = wlan_tx_timeout;
 	dev->get_stats = wlan_get_stats;
@@ -918,7 +919,6 @@ int libertas_add_mesh(wlan_private *priv, struct device *dev)
 	mesh_dev->open = mesh_open;
 	mesh_dev->hard_start_xmit = mesh_pre_start_xmit;
 	mesh_dev->stop = mesh_close;
-	mesh_dev->do_ioctl = libertas_do_ioctl;
 	mesh_dev->get_stats = wlan_get_stats;
 	mesh_dev->set_mac_address = wlan_set_mac_address;
 	mesh_dev->ethtool_ops = &libertas_ethtool_ops;

drivers/net/wireless/libertas/scan.c

@@ -214,38 +214,6 @@ static int is_network_compatible(wlan_adapter * adapter,
 	return matched;
 }
 
-/**
- *  @brief Post process the scan table after a new scan command has completed
- *
- *  Inspect each entry of the scan table and try to find an entry that
- *    matches our current associated/joined network from the scan.  If
- *    one is found, update the stored copy of the bssdescriptor for our
- *    current network.
- *
- *  Debug dump the current scan table contents if compiled accordingly.
- *
- *  @param priv   A pointer to wlan_private structure
- *
- *  @return       void
- */
-static void wlan_scan_process_results(wlan_private * priv)
-{
-	wlan_adapter *adapter = priv->adapter;
-	struct bss_descriptor * iter_bss;
-	int i = 0;
-
-	if (adapter->connect_status == libertas_connected)
-		return;
-
-	mutex_lock(&adapter->lock);
-	list_for_each_entry (iter_bss, &adapter->network_list, list) {
-		lbs_deb_scan("Scan:(%02d) " MAC_FMT ", RSSI[%03d], SSID[%s]\n",
-		       i++, MAC_ARG(iter_bss->bssid), (s32) iter_bss->rssi,
-		       escape_essid(iter_bss->ssid, iter_bss->ssid_len));
-	}
-	mutex_unlock(&adapter->lock);
-}
-
 /**
  *  @brief Create a channel list for the driver to scan based on region info
  *
@@ -791,6 +759,10 @@ int wlan_scan_networks(wlan_private * priv,
 	u8 scancurrentchanonly;
 	int maxchanperscan;
 	int ret;
+#ifdef CONFIG_LIBERTAS_DEBUG
+	struct bss_descriptor * iter_bss;
+	int i = 0;
+#endif
 
 	lbs_deb_enter(LBS_DEB_ASSOC);
 
@@ -832,11 +804,16 @@ int wlan_scan_networks(wlan_private * priv,
 				     puserscanin,
 				     full_scan);
 
-	/*  Process the resulting scan table:
-	 *    - Remove any bad ssids
-	 *    - Update our current BSS information from scan data
-	 */
-	wlan_scan_process_results(priv);
+#ifdef CONFIG_LIBERTAS_DEBUG
+	/* Dump the scan table */
+	mutex_lock(&adapter->lock);
+	list_for_each_entry (iter_bss, &adapter->network_list, list) {
+		lbs_deb_scan("Scan:(%02d) " MAC_FMT ", RSSI[%03d], SSID[%s]\n",
+		       i++, MAC_ARG(iter_bss->bssid), (s32) iter_bss->rssi,
+		       escape_essid(iter_bss->ssid, iter_bss->ssid_len));
+	}
+	mutex_unlock(&adapter->lock);
+#endif
 
 	if (priv->adapter->connect_status == libertas_connected) {
 		netif_carrier_on(priv->dev);

drivers/net/wireless/libertas/wext.c

@@ -913,148 +913,6 @@ static int wlan_get_power(struct net_device *dev, struct iw_request_info *info,
 	return 0;
 }
 
-/*
- * iwpriv settable callbacks
- */
-
-static const iw_handler wlan_private_handler[] = {
-	NULL,			/* SIOCIWFIRSTPRIV */
-};
-
-static const struct iw_priv_args wlan_private_args[] = {
-	/*
-	 * { cmd, set_args, get_args, name }
-	 */
-	/* Using iwpriv sub-command feature */
-	{
-	 WLAN_SETONEINT_GETNONE,	/* IOCTL: 24 */
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 ""},
-	{
-	 WLANSETREGION,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "setregioncode"},
-	{
-	 WLAN_SUBCMD_MESH_SET_TTL,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "mesh_set_ttl"},
-	{
-	 WLAN_SETNONE_GETONEINT,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 ""},
-	{
-	 WLANGETREGION,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "getregioncode"},
-	{
-	 WLAN_SUBCMD_FWT_CLEANUP,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "fwt_cleanup"},
-	{
-	 WLAN_SUBCMD_FWT_TIME,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "fwt_time"},
-	{
-	 WLAN_SUBCMD_MESH_GET_TTL,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "mesh_get_ttl"},
-	{
-	 WLAN_SETNONE_GETNONE,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 ""},
-	{
-	 WLAN_SUBCMD_FWT_RESET,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 "fwt_reset"},
-	{
-	 WLAN_SUBCMD_BT_RESET,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 "bt_reset"},
-	{
-	 WLAN_SET128CHAR_GET128CHAR,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 ""},
-	/* BT Management */
-	{
-	 WLAN_SUBCMD_BT_ADD,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "bt_add"},
-	{
-	 WLAN_SUBCMD_BT_DEL,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "bt_del"},
-	{
-	 WLAN_SUBCMD_BT_LIST,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "bt_list"},
-	{
-	 WLAN_SUBCMD_BT_SET_INVERT,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "bt_set_invert"},
-	{
-	 WLAN_SUBCMD_BT_GET_INVERT,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "bt_get_invert"},
-	/* FWT Management */
-	{
-	 WLAN_SUBCMD_FWT_ADD,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "fwt_add"},
-	{
-	 WLAN_SUBCMD_FWT_DEL,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "fwt_del"},
-	{
-	 WLAN_SUBCMD_FWT_LOOKUP,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "fwt_lookup"},
-	{
-	 WLAN_SUBCMD_FWT_LIST_NEIGHBOR,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "fwt_list_neigh"},
-	{
-	 WLAN_SUBCMD_FWT_LIST,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "fwt_list"},
-	{
-	 WLAN_SUBCMD_FWT_LIST_ROUTE,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "fwt_list_route"},
-	{
-	 WLAN_SET_GET_SIXTEEN_INT,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 ""},
-	{
-	 WLAN_LED_GPIO_CTRL,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "ledgpio"},
-};
-
 static struct iw_statistics *wlan_get_wireless_stats(struct net_device *dev)
 {
 	enum {
@@ -2444,22 +2302,12 @@ static const iw_handler mesh_wlan_handler[] = {
 };
 struct iw_handler_def libertas_handler_def = {
 	.num_standard	= sizeof(wlan_handler) / sizeof(iw_handler),
-	.num_private	= sizeof(wlan_private_handler) / sizeof(iw_handler),
-	.num_private_args = sizeof(wlan_private_args) /
-		sizeof(struct iw_priv_args),
 	.standard	= (iw_handler *) wlan_handler,
-	.private	= (iw_handler *) wlan_private_handler,
-	.private_args	= (struct iw_priv_args *)wlan_private_args,
 	.get_wireless_stats = wlan_get_wireless_stats,
 };
 
 struct iw_handler_def mesh_handler_def = {
 	.num_standard	= sizeof(mesh_wlan_handler) / sizeof(iw_handler),
-	.num_private	= sizeof(wlan_private_handler) / sizeof(iw_handler),
-	.num_private_args = sizeof(wlan_private_args) /
-		sizeof(struct iw_priv_args),
 	.standard	= (iw_handler *) mesh_wlan_handler,
-	.private	= (iw_handler *) wlan_private_handler,
-	.private_args	= (struct iw_priv_args *)wlan_private_args,
 	.get_wireless_stats = wlan_get_wireless_stats,
 };

drivers/net/wireless/libertas/wext.h

@@ -7,45 +7,6 @@
 #define SUBCMD_OFFSET			4
 #define SUBCMD_DATA(x)			*((int *)(x->u.name + SUBCMD_OFFSET))
 
-/** PRIVATE CMD ID */
-#define	WLANIOCTL			SIOCIWFIRSTPRIV
-
-#define WLAN_SETNONE_GETNONE	        (WLANIOCTL + 8)
-#define WLAN_SUBCMD_BT_RESET			13
-#define WLAN_SUBCMD_FWT_RESET			14
-
-#define WLAN_SETNONE_GETONEINT		(WLANIOCTL + 15)
-#define WLANGETREGION				1
-
-#define WLAN_SUBCMD_FWT_CLEANUP			15
-#define WLAN_SUBCMD_FWT_TIME			16
-#define WLAN_SUBCMD_MESH_GET_TTL		17
-#define WLAN_SUBCMD_BT_GET_INVERT		18
-
-#define WLAN_SETONEINT_GETNONE		(WLANIOCTL + 24)
-#define WLANSETREGION				8
-#define WLAN_SUBCMD_MESH_SET_TTL		18
-#define WLAN_SUBCMD_BT_SET_INVERT		19
-
-#define WLAN_SET128CHAR_GET128CHAR	(WLANIOCTL + 25)
-#define WLAN_SUBCMD_BT_ADD			18
-#define WLAN_SUBCMD_BT_DEL   			19
-#define WLAN_SUBCMD_BT_LIST			20
-#define WLAN_SUBCMD_FWT_ADD			21
-#define WLAN_SUBCMD_FWT_DEL   			22
-#define WLAN_SUBCMD_FWT_LOOKUP			23
-#define WLAN_SUBCMD_FWT_LIST_NEIGHBOR		24
-#define WLAN_SUBCMD_FWT_LIST			25
-#define WLAN_SUBCMD_FWT_LIST_ROUTE		26
-
-#define WLAN_SET_GET_SIXTEEN_INT       (WLANIOCTL + 29)
-#define WLAN_LED_GPIO_CTRL			5
-
-#define WLAN_LINKMODE_802_3			0
-#define WLAN_LINKMODE_802_11			2
-#define WLAN_RADIOMODE_NONE    			0
-#define WLAN_RADIOMODE_RADIOTAP			2
-
 /** wlan_ioctl_regrdwr */
 struct wlan_ioctl_regrdwr {
 	/** Which register to access */
@@ -57,9 +18,13 @@ struct wlan_ioctl_regrdwr {
 	u32 value;
 };
 
+#define WLAN_LINKMODE_802_3			0
+#define WLAN_LINKMODE_802_11			2
+#define WLAN_RADIOMODE_NONE			0
+#define WLAN_RADIOMODE_RADIOTAP			2
+
 extern struct iw_handler_def libertas_handler_def;
 extern struct iw_handler_def mesh_handler_def;
-int libertas_do_ioctl(struct net_device *dev, struct ifreq *req, int i);
 int wlan_radio_ioctl(wlan_private * priv, u8 option);
 
 #endif				/* _WLAN_WEXT_H_ */