Skip to content

L
linux
Commit 3a585bf5 authored by Marc Zyngier's avatar Marc Zyngier Committed by Linus Torvalds
Browse files
Options

[netdrvr de4x5] big modernization / cleanup 

The enclosed patch tries to clean the tulip de4x5 driver, and update
it to some of the 2.6 APIs :

- Use PCI and EISA probing APIs
- Use generic DMA API
- Fix DE425 init on the Jensen
- Remove de4x5 from Space.c

It's been tested on x86 and Alpha, with a DE425 (21040, EISA), a DE435
(21040, PCI) and a quad DLink (4*21143, PCI).

The major problem with this patch is that, because of the Space.c
removal, interfaces get potentially renumbered. This has been
discussed to death on lkml, without any obvious solution. IMHO, we'd
better remove as many drivers as we can from Space.c before
2.6.0-final ships...
parent 7c219ac7
Show whitespace changes
Inline Side-by-side
Showing with 354 additions and 494 deletions
drivers/net/Space.c
View file @ 3a585bf5
...@@ -62,7 +62,6 @@ extern int eth16i_probe(struct net_device *); ...@@ -62,7 +62,6 @@ extern int eth16i_probe(struct net_device *);
extern int depca_probe(struct net_device *); extern int depca_probe(struct net_device *);
extern int i82596_probe(struct net_device *); extern int i82596_probe(struct net_device *);
extern int ewrk3_probe(struct net_device *); extern int ewrk3_probe(struct net_device *);
extern int de4x5_probe(struct net_device *);
extern int el1_probe(struct net_device *); extern int el1_probe(struct net_device *);
extern int wavelan_probe(struct net_device *); extern int wavelan_probe(struct net_device *);
extern int arlan_probe(struct net_device *); extern int arlan_probe(struct net_device *);
...@@ -152,12 +151,9 @@ static int __init probe_list(struct net_device *dev, struct devprobe *plist) ...@@ -152,12 +151,9 @@ static int __init probe_list(struct net_device *dev, struct devprobe *plist)
* This is a bit of an artificial separation as there are PCI drivers * This is a bit of an artificial separation as there are PCI drivers
* that also probe for EISA cards (in the PCI group) and there are ISA * that also probe for EISA cards (in the PCI group) and there are ISA
* drivers that probe for EISA cards (in the ISA group). These are the * drivers that probe for EISA cards (in the ISA group). These are the
* EISA only driver probes, and also the legacy PCI probes * legacy EISA only driver probes, and also the legacy PCI probes
*/ */
static struct devprobe eisa_probes[] __initdata = { static struct devprobe eisa_probes[] __initdata = {
#ifdef CONFIG_DE4X5 /* DEC DE425, DE434, DE435 adapters */
{de4x5_probe, 0},
#endif
#ifdef CONFIG_ULTRA32 #ifdef CONFIG_ULTRA32
{ultra32_probe, 0}, {ultra32_probe, 0},
#endif #endif
......
drivers/net/tulip/de4x5.c
View file @ 3a585bf5
...@@ -437,6 +437,9 @@ ...@@ -437,6 +437,9 @@
present. present.
<france@handhelds.org> <france@handhelds.org>
0.547 08-Nov-01 Use library crc32 functions by <Matt_Domsch@dell.com> 0.547 08-Nov-01 Use library crc32 functions by <Matt_Domsch@dell.com>
0.548 30-Aug-03 Big 2.6 cleanup. Ported to PCI/EISA probing and
generic DMA APIs. Fixed DE425 support on Alpha.
<maz@wild-wind.fr.eu.org>
========================================================================= =========================================================================
*/ */
...@@ -450,6 +453,7 @@ ...@@ -450,6 +453,7 @@
#include <linux/ioport.h> #include <linux/ioport.h>
#include <linux/slab.h> #include <linux/slab.h>
#include <linux/pci.h> #include <linux/pci.h>
#include <linux/eisa.h>
#include <linux/delay.h> #include <linux/delay.h>
#include <linux/init.h> #include <linux/init.h>
#include <linux/spinlock.h> #include <linux/spinlock.h>
...@@ -461,6 +465,8 @@ ...@@ -461,6 +465,8 @@
#include <linux/types.h> #include <linux/types.h>
#include <linux/unistd.h> #include <linux/unistd.h>
#include <linux/ctype.h> #include <linux/ctype.h>
#include <linux/dma-mapping.h>
#include <linux/moduleparam.h>
#include <asm/bitops.h> #include <asm/bitops.h>
#include <asm/io.h> #include <asm/io.h>
...@@ -625,13 +631,13 @@ struct parameters { ...@@ -625,13 +631,13 @@ struct parameters {
#define DE4X5_EISA_IO_PORTS 0x0c00 /* I/O port base address, slot 0 */ #define DE4X5_EISA_IO_PORTS 0x0c00 /* I/O port base address, slot 0 */
#define DE4X5_EISA_TOTAL_SIZE 0x100 /* I/O address extent */ #define DE4X5_EISA_TOTAL_SIZE 0x100 /* I/O address extent */
#define MAX_EISA_SLOTS 16
#define EISA_SLOT_INC 0x1000
#define EISA_ALLOWED_IRQ_LIST {5, 9, 10, 11} #define EISA_ALLOWED_IRQ_LIST {5, 9, 10, 11}
#define DE4X5_SIGNATURE {"DE425","DE434","DE435","DE450","DE500"} #define DE4X5_SIGNATURE {"DE425","DE434","DE435","DE450","DE500"}
#define DE4X5_NAME_LENGTH 8 #define DE4X5_NAME_LENGTH 8
static c_char *de4x5_signatures[] = DE4X5_SIGNATURE;
/* /*
** Ethernet PROM defines for DC21040 ** Ethernet PROM defines for DC21040
*/ */
...@@ -644,7 +650,6 @@ struct parameters { ...@@ -644,7 +650,6 @@ struct parameters {
#define PCI_MAX_BUS_NUM 8 #define PCI_MAX_BUS_NUM 8
#define DE4X5_PCI_TOTAL_SIZE 0x80 /* I/O address extent */ #define DE4X5_PCI_TOTAL_SIZE 0x80 /* I/O address extent */
#define DE4X5_CLASS_CODE 0x00020000 /* Network controller, Ethernet */ #define DE4X5_CLASS_CODE 0x00020000 /* Network controller, Ethernet */
#define NO_MORE_PCI -2 /* PCI bus search all done */
/* /*
** Memory Alignment. Each descriptor is 4 longwords long. To force a ** Memory Alignment. Each descriptor is 4 longwords long. To force a
...@@ -819,7 +824,6 @@ struct de4x5_private { ...@@ -819,7 +824,6 @@ struct de4x5_private {
struct timer_list timer; /* Timer info for kernel */ struct timer_list timer; /* Timer info for kernel */
int tmp; /* Temporary global per card */ int tmp; /* Temporary global per card */
struct { struct {
void *priv; /* Original kmalloc'd mem addr */
u_long lock; /* Lock the cache accesses */ u_long lock; /* Lock the cache accesses */
s32 csr0; /* Saved Bus Mode Register */ s32 csr0; /* Saved Bus Mode Register */
s32 csr6; /* Saved Operating Mode Reg. */ s32 csr6; /* Saved Operating Mode Reg. */
...@@ -833,7 +837,7 @@ struct de4x5_private { ...@@ -833,7 +837,7 @@ struct de4x5_private {
struct sk_buff *skb; /* Save the (re-ordered) skb's */ struct sk_buff *skb; /* Save the (re-ordered) skb's */
} cache; } cache;
struct de4x5_srom srom; /* A copy of the SROM */ struct de4x5_srom srom; /* A copy of the SROM */
struct net_device *next_module; /* Link to the next module */ int cfrv; /* Card CFRV copy */
int rx_ovf; /* Check for 'RX overflow' tag */ int rx_ovf; /* Check for 'RX overflow' tag */
int useSROM; /* For non-DEC card use SROM */ int useSROM; /* For non-DEC card use SROM */
int useMII; /* Infoblock using the MII */ int useMII; /* Infoblock using the MII */
...@@ -850,28 +854,12 @@ struct de4x5_private { ...@@ -850,28 +854,12 @@ struct de4x5_private {
u_char *rst; /* Pointer to Type 5 reset info */ u_char *rst; /* Pointer to Type 5 reset info */
u_char ibn; /* Infoblock number */ u_char ibn; /* Infoblock number */
struct parameters params; /* Command line/ #defined params */ struct parameters params; /* Command line/ #defined params */
struct pci_dev *pdev; /* Device cookie for DMA alloc */ struct device *gendev; /* Generic device */
dma_addr_t dma_rings; /* DMA handle for rings */ dma_addr_t dma_rings; /* DMA handle for rings */
int dma_size; /* Size of the DMA area */ int dma_size; /* Size of the DMA area */
char *rx_bufs; /* rx bufs on alpha, sparc, ... */ char *rx_bufs; /* rx bufs on alpha, sparc, ... */
}; };
/*
** Kludge to get around the fact that the CSR addresses have different
** offsets in the PCI and EISA boards. Also note that the ethernet address
** PROM is accessed differently.
*/
static struct de4x5_bus_type {
int bus;
int bus_num;
int device;
int chipset;
struct de4x5_srom srom;
int autosense;
int useSROM;
struct pci_dev *pdev;
} bus;
/* /*
** To get around certain poxy cards that don't provide an SROM ** To get around certain poxy cards that don't provide an SROM
** for the second and more DECchip, I have to key off the first ** for the second and more DECchip, I have to key off the first
...@@ -919,7 +907,7 @@ static int de4x5_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); ...@@ -919,7 +907,7 @@ static int de4x5_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
/* /*
** Private functions ** Private functions
*/ */
static int de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev); static int de4x5_hw_init(struct net_device *dev, u_long iobase, struct device *gendev);
static int de4x5_init(struct net_device *dev); static int de4x5_init(struct net_device *dev);
static int de4x5_sw_reset(struct net_device *dev); static int de4x5_sw_reset(struct net_device *dev);
static int de4x5_rx(struct net_device *dev); static int de4x5_rx(struct net_device *dev);
...@@ -962,11 +950,11 @@ static int de4x5_reset_phy(struct net_device *dev); ...@@ -962,11 +950,11 @@ static int de4x5_reset_phy(struct net_device *dev);
static void reset_init_sia(struct net_device *dev, s32 sicr, s32 strr, s32 sigr); static void reset_init_sia(struct net_device *dev, s32 sicr, s32 strr, s32 sigr);
static int test_ans(struct net_device *dev, s32 irqs, s32 irq_mask, s32 msec); static int test_ans(struct net_device *dev, s32 irqs, s32 irq_mask, s32 msec);
static int test_tp(struct net_device *dev, s32 msec); static int test_tp(struct net_device *dev, s32 msec);
static int EISA_signature(char *name, s32 eisa_id); static int EISA_signature(char *name, struct device *device);
static int PCI_signature(char *name, struct de4x5_bus_type *lp); static int PCI_signature(char *name, struct de4x5_private *lp);
static void DevicePresent(u_long iobase); static void DevicePresent(struct net_device *dev, u_long iobase);
static void enet_addr_rst(u_long aprom_addr); static void enet_addr_rst(u_long aprom_addr);
static int de4x5_bad_srom(struct de4x5_bus_type *lp); static int de4x5_bad_srom(struct de4x5_private *lp);
static short srom_rd(u_long address, u_char offset); static short srom_rd(u_long address, u_char offset);
static void srom_latch(u_int command, u_long address); static void srom_latch(u_int command, u_long address);
static void srom_command(u_int command, u_long address); static void srom_command(u_int command, u_long address);
...@@ -994,12 +982,7 @@ static void SetMulticastFilter(struct net_device *dev); ...@@ -994,12 +982,7 @@ static void SetMulticastFilter(struct net_device *dev);
static int get_hw_addr(struct net_device *dev); static int get_hw_addr(struct net_device *dev);
static void srom_repair(struct net_device *dev, int card); static void srom_repair(struct net_device *dev, int card);
static int test_bad_enet(struct net_device *dev, int status); static int test_bad_enet(struct net_device *dev, int status);
static int an_exception(struct de4x5_bus_type *lp); static int an_exception(struct de4x5_private *lp);
#if !defined(__sparc_v9__) && !defined(__powerpc__) && !defined(__alpha__)
static void eisa_probe(struct net_device *dev, u_long iobase);
#endif
static void pci_probe(struct net_device *dev, u_long iobase);
static void srom_search(struct pci_dev *pdev);
static char *build_setup_frame(struct net_device *dev, int mode); static char *build_setup_frame(struct net_device *dev, int mode);
static void disable_ast(struct net_device *dev); static void disable_ast(struct net_device *dev);
static void enable_ast(struct net_device *dev, u32 time_out); static void enable_ast(struct net_device *dev, u32 time_out);
...@@ -1008,7 +991,6 @@ static int gep_rd(struct net_device *dev); ...@@ -1008,7 +991,6 @@ static int gep_rd(struct net_device *dev);
static void gep_wr(s32 data, struct net_device *dev); static void gep_wr(s32 data, struct net_device *dev);
static void timeout(struct net_device *dev, void (*fn)(u_long data), u_long data, u_long msec); static void timeout(struct net_device *dev, void (*fn)(u_long data), u_long data, u_long msec);
static void yawn(struct net_device *dev, int state); static void yawn(struct net_device *dev, int state);
static void link_modules(struct net_device *dev, struct net_device *tmp);
static void de4x5_parse_params(struct net_device *dev); static void de4x5_parse_params(struct net_device *dev);
static void de4x5_dbg_open(struct net_device *dev); static void de4x5_dbg_open(struct net_device *dev);
static void de4x5_dbg_mii(struct net_device *dev, int k); static void de4x5_dbg_mii(struct net_device *dev, int k);
...@@ -1028,40 +1010,25 @@ static int type4_infoblock(struct net_device *dev, u_char count, u_char *p); ...@@ -1028,40 +1010,25 @@ static int type4_infoblock(struct net_device *dev, u_char count, u_char *p);
static int type5_infoblock(struct net_device *dev, u_char count, u_char *p); static int type5_infoblock(struct net_device *dev, u_char count, u_char *p);
static int compact_infoblock(struct net_device *dev, u_char count, u_char *p); static int compact_infoblock(struct net_device *dev, u_char count, u_char *p);
#ifdef MODULE /*
static struct net_device *unlink_modules(struct net_device *p); ** Note now that module autoprobing is allowed under EISA and PCI. The
static struct net_device *insert_device(struct net_device *dev, u_long iobase, ** IRQ lines will not be auto-detected; instead I'll rely on the BIOSes
int (*init)(struct net_device *)); ** to "do the right thing".
static int count_adapters(void); */
static int loading_module = 1;
MODULE_PARM(de4x5_debug, "i"); static int io=0x0;/* EDIT THIS LINE FOR YOUR CONFIGURATION IF NEEDED */
MODULE_PARM(dec_only, "i");
MODULE_PARM(args, "s"); module_param(io, int, 0);
module_param(de4x5_debug, int, 0);
module_param(dec_only, int, 0);
module_param(args, charp, 0);
MODULE_PARM_DESC(io, "de4x5 I/O base address");
MODULE_PARM_DESC(de4x5_debug, "de4x5 debug mask"); MODULE_PARM_DESC(de4x5_debug, "de4x5 debug mask");
MODULE_PARM_DESC(dec_only, "de4x5 probe only for Digital boards (0-1)"); MODULE_PARM_DESC(dec_only, "de4x5 probe only for Digital boards (0-1)");
MODULE_PARM_DESC(args, "de4x5 full duplex and media type settings; see de4x5.c for details"); MODULE_PARM_DESC(args, "de4x5 full duplex and media type settings; see de4x5.c for details");
MODULE_LICENSE("GPL"); MODULE_LICENSE("GPL");
# else
static int loading_module;
#endif /* MODULE */
static char name[DE4X5_NAME_LENGTH + 1];
#if !defined(__sparc_v9__) && !defined(__powerpc__) && !defined(__alpha__)
static u_char de4x5_irq[] = EISA_ALLOWED_IRQ_LIST;
static int lastEISA;
# ifdef DE4X5_FORCE_EISA /* Force an EISA bus probe or not */
static int forceEISA = 1;
# else
static int forceEISA;
# endif
#endif
static int num_de4x5s;
static int cfrv, useSROM;
static int lastPCI = -1;
static struct net_device *lastModule;
static struct pci_dev *pdev;
/* /*
** List the SROM infoleaf functions and chipsets ** List the SROM infoleaf functions and chipsets
*/ */
...@@ -1115,37 +1082,22 @@ static int (*dc_infoblock[])(struct net_device *dev, u_char, u_char *) = { ...@@ -1115,37 +1082,22 @@ static int (*dc_infoblock[])(struct net_device *dev, u_char, u_char *) = {
} }
/*
** Autoprobing in modules is allowed here. See the top of the file for
** more info.
*/
int __init
de4x5_probe(struct net_device *dev)
{
u_long iobase = dev->base_addr;
pci_probe(dev, iobase);
#if !defined(__sparc_v9__) && !defined(__powerpc__) && !defined(__alpha__)
if ((lastPCI == NO_MORE_PCI) && ((num_de4x5s == 0) || forceEISA)) {
eisa_probe(dev, iobase);
}
#endif
return (dev->priv ? 0 : -ENODEV);
}
static int __init static int __init
de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) de4x5_hw_init(struct net_device *dev, u_long iobase, struct device *gendev)
{ {
struct de4x5_bus_type *lp = &bus; char name[DE4X5_NAME_LENGTH + 1];
struct de4x5_private *lp = dev->priv;
struct pci_dev *pdev = NULL;
int i, status=0; int i, status=0;
char *tmp;
gendev->driver_data = dev;
/* Ensure we're not sleeping */ /* Ensure we're not sleeping */
if (lp->bus == EISA) { if (lp->bus == EISA) {
outb(WAKEUP, PCI_CFPM); outb(WAKEUP, PCI_CFPM);
} else { } else {
pci_write_config_byte(lp->pdev, PCI_CFDA_PSM, WAKEUP); pdev = to_pci_dev (gendev);
pci_write_config_byte(pdev, PCI_CFDA_PSM, WAKEUP);
} }
mdelay(10); mdelay(10);
...@@ -1158,11 +1110,11 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) ...@@ -1158,11 +1110,11 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev)
/* /*
** Now find out what kind of DC21040/DC21041/DC21140 board we have. ** Now find out what kind of DC21040/DC21041/DC21140 board we have.
*/ */
useSROM = FALSE; lp->useSROM = FALSE;
if (lp->bus == PCI) { if (lp->bus == PCI) {
PCI_signature(name, lp); PCI_signature(name, lp);
} else { } else {
EISA_signature(name, EISA_ID0); EISA_signature(name, gendev);
} }
if (*name == '\0') { /* Not found a board signature */ if (*name == '\0') { /* Not found a board signature */
...@@ -1170,13 +1122,7 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) ...@@ -1170,13 +1122,7 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev)
} }
dev->base_addr = iobase; dev->base_addr = iobase;
if (lp->bus == EISA) { printk ("%s: %s at 0x%04lx", gendev->bus_id, name, iobase);
printk("%s: %s at 0x%04lx (EISA slot %ld)",
dev->name, name, iobase, ((iobase>>12)&0x0f));
} else { /* PCI port address */
printk("%s: %s at 0x%04lx (PCI bus %d, device %d)", dev->name, name,
iobase, lp->bus_num, lp->device);
}
printk(", h/w address "); printk(", h/w address ");
status = get_hw_addr(dev); status = get_hw_addr(dev);
...@@ -1189,38 +1135,12 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) ...@@ -1189,38 +1135,12 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev)
printk(" which has an Ethernet PROM CRC error.\n"); printk(" which has an Ethernet PROM CRC error.\n");
return -ENXIO; return -ENXIO;
} else { } else {
struct de4x5_private *lp;
/*
** Reserve a section of kernel memory for the adapter
** private area and the TX/RX descriptor rings.
*/
dev->priv = (void *) kmalloc(sizeof(struct de4x5_private) + DE4X5_ALIGN,
GFP_KERNEL);
if (dev->priv == NULL) {
return -ENOMEM;
}
/*
** Align to a longword boundary
*/
tmp = dev->priv;
dev->priv = (void *)(((u_long)dev->priv + DE4X5_ALIGN) & ~DE4X5_ALIGN);
lp = (struct de4x5_private *)dev->priv;
memset(dev->priv, 0, sizeof(struct de4x5_private));
lp->bus = bus.bus;
lp->bus_num = bus.bus_num;
lp->device = bus.device;
lp->chipset = bus.chipset;
lp->cache.priv = tmp;
lp->cache.gepc = GEP_INIT; lp->cache.gepc = GEP_INIT;
lp->asBit = GEP_SLNK; lp->asBit = GEP_SLNK;
lp->asPolarity = GEP_SLNK; lp->asPolarity = GEP_SLNK;
lp->asBitValid = TRUE; lp->asBitValid = TRUE;
lp->timeout = -1; lp->timeout = -1;
lp->useSROM = useSROM; lp->gendev = gendev;
lp->pdev = pdev;
memcpy((char *)&lp->srom,(char *)&bus.srom,sizeof(struct de4x5_srom));
lp->lock = (spinlock_t) SPIN_LOCK_UNLOCKED; lp->lock = (spinlock_t) SPIN_LOCK_UNLOCKED;
init_timer(&lp->timer); init_timer(&lp->timer);
de4x5_parse_params(dev); de4x5_parse_params(dev);
...@@ -1238,16 +1158,15 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) ...@@ -1238,16 +1158,15 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev)
} }
} }
lp->fdx = lp->params.fdx; lp->fdx = lp->params.fdx;
sprintf(lp->adapter_name,"%s (%s)", name, dev->name); sprintf(lp->adapter_name,"%s (%s)", name, gendev->bus_id);
lp->dma_size = (NUM_RX_DESC + NUM_TX_DESC) * sizeof(struct de4x5_desc); lp->dma_size = (NUM_RX_DESC + NUM_TX_DESC) * sizeof(struct de4x5_desc);
#if defined(__alpha__) || defined(__powerpc__) || defined(__sparc_v9__) || defined(DE4X5_DO_MEMCPY) #if defined(__alpha__) || defined(__powerpc__) || defined(__sparc_v9__) || defined(DE4X5_DO_MEMCPY)
lp->dma_size += RX_BUFF_SZ * NUM_RX_DESC + DE4X5_ALIGN; lp->dma_size += RX_BUFF_SZ * NUM_RX_DESC + DE4X5_ALIGN;
#endif #endif
lp->rx_ring = pci_alloc_consistent(pdev, lp->dma_size, &lp->dma_rings); lp->rx_ring = dma_alloc_coherent(gendev, lp->dma_size,
&lp->dma_rings, GFP_ATOMIC);
if (lp->rx_ring == NULL) { if (lp->rx_ring == NULL) {
kfree(lp->cache.priv);
lp->cache.priv = NULL;
return -ENOMEM; return -ENOMEM;
} }
...@@ -1289,10 +1208,6 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) ...@@ -1289,10 +1208,6 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev)
barrier(); barrier();
request_region(iobase, (lp->bus == PCI ? DE4X5_PCI_TOTAL_SIZE :
DE4X5_EISA_TOTAL_SIZE),
lp->adapter_name);
lp->rxRingSize = NUM_RX_DESC; lp->rxRingSize = NUM_RX_DESC;
lp->txRingSize = NUM_TX_DESC; lp->txRingSize = NUM_TX_DESC;
...@@ -1313,7 +1228,7 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) ...@@ -1313,7 +1228,7 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev)
create_packet(dev, lp->frame, sizeof(lp->frame)); create_packet(dev, lp->frame, sizeof(lp->frame));
/* Check if the RX overflow bug needs testing for */ /* Check if the RX overflow bug needs testing for */
i = cfrv & 0x000000fe; i = lp->cfrv & 0x000000fe;
if ((lp->chipset == DC21140) && (i == 0x20)) { if ((lp->chipset == DC21140) && (i == 0x20)) {
lp->rx_ovf = 1; lp->rx_ovf = 1;
} }
...@@ -1350,7 +1265,7 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) ...@@ -1350,7 +1265,7 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev)
/* The DE4X5-specific entries in the device structure. */ /* The DE4X5-specific entries in the device structure. */
SET_MODULE_OWNER(dev); SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev); SET_NETDEV_DEV(dev, gendev);
dev->open = &de4x5_open; dev->open = &de4x5_open;
dev->hard_start_xmit = &de4x5_queue_pkt; dev->hard_start_xmit = &de4x5_queue_pkt;
dev->stop = &de4x5_close; dev->stop = &de4x5_close;
...@@ -1361,7 +1276,11 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev) ...@@ -1361,7 +1276,11 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct pci_dev *pdev)
dev->mem_start = 0; dev->mem_start = 0;
/* Fill in the generic fields of the device structure. */ /* Fill in the generic fields of the device structure. */
ether_setup(dev); if ((status = register_netdev (dev))) {
dma_free_coherent (gendev, lp->dma_size,
lp->rx_ring, lp->dma_rings);
return status;
}
/* Let the adapter sleep to save power */ /* Let the adapter sleep to save power */
yawn(dev, SLEEP); yawn(dev, SLEEP);
...@@ -1766,9 +1685,9 @@ de4x5_rx(struct net_device *dev) ...@@ -1766,9 +1685,9 @@ de4x5_rx(struct net_device *dev)
static inline void static inline void
de4x5_free_tx_buff(struct de4x5_private *lp, int entry) de4x5_free_tx_buff(struct de4x5_private *lp, int entry)
{ {
pci_unmap_single(lp->pdev, le32_to_cpu(lp->tx_ring[entry].buf), dma_unmap_single(lp->gendev, le32_to_cpu(lp->tx_ring[entry].buf),
le32_to_cpu(lp->tx_ring[entry].des1) & TD_TBS1, le32_to_cpu(lp->tx_ring[entry].des1) & TD_TBS1,
PCI_DMA_TODEVICE); DMA_TO_DEVICE);
if ((u_long) lp->tx_skb[entry] > 1) if ((u_long) lp->tx_skb[entry] > 1)
dev_kfree_skb_irq(lp->tx_skb[entry]); dev_kfree_skb_irq(lp->tx_skb[entry]);
lp->tx_skb[entry] = NULL; lp->tx_skb[entry] = NULL;
...@@ -1987,7 +1906,7 @@ load_packet(struct net_device *dev, char *buf, u32 flags, struct sk_buff *skb) ...@@ -1987,7 +1906,7 @@ load_packet(struct net_device *dev, char *buf, u32 flags, struct sk_buff *skb)
{ {
struct de4x5_private *lp = (struct de4x5_private *)dev->priv; struct de4x5_private *lp = (struct de4x5_private *)dev->priv;
int entry = (lp->tx_new ? lp->tx_new-1 : lp->txRingSize-1); int entry = (lp->tx_new ? lp->tx_new-1 : lp->txRingSize-1);
dma_addr_t buf_dma = pci_map_single(lp->pdev, buf, flags & TD_TBS1, PCI_DMA_TODEVICE); dma_addr_t buf_dma = dma_map_single(lp->gendev, buf, flags & TD_TBS1, DMA_TO_DEVICE);
lp->tx_ring[lp->tx_new].buf = cpu_to_le32(buf_dma); lp->tx_ring[lp->tx_new].buf = cpu_to_le32(buf_dma);
lp->tx_ring[lp->tx_new].des1 &= cpu_to_le32(TD_TER); lp->tx_ring[lp->tx_new].des1 &= cpu_to_le32(TD_TER);
...@@ -2084,75 +2003,199 @@ SetMulticastFilter(struct net_device *dev) ...@@ -2084,75 +2003,199 @@ SetMulticastFilter(struct net_device *dev)
return; return;
} }
#if !defined(__sparc_v9__) && !defined(__powerpc__) && !defined(__alpha__) #ifdef CONFIG_EISA
/*
** EISA bus I/O device probe. Probe from slot 1 since slot 0 is usually static u_char de4x5_irq[] = EISA_ALLOWED_IRQ_LIST;
** the motherboard. Upto 15 EISA devices are supported.
*/ static int __init de4x5_eisa_probe (struct device *gendev)
static void __init
eisa_probe(struct net_device *dev, u_long ioaddr)
{ {
int i, maxSlots, status, device; struct eisa_device *edev;
u_char irq; u_long iobase;
u_char irq, regval;
u_short vendor; u_short vendor;
u32 cfid; u32 cfid;
u_long iobase; int status, device;
struct de4x5_bus_type *lp = &bus; struct net_device *dev;
char name[DE4X5_STRLEN]; struct de4x5_private *lp;
if (lastEISA == MAX_EISA_SLOTS) return;/* No more EISA devices to search */ edev = to_eisa_device (gendev);
iobase = edev->base_addr;
lp->bus = EISA; if (!request_region (iobase, DE4X5_EISA_TOTAL_SIZE, "de4x5"))
return -EBUSY;
if (ioaddr == 0) { /* Autoprobing */ if (!request_region (iobase + DE4X5_EISA_IO_PORTS,
iobase = EISA_SLOT_INC; /* Get the first slot address */ DE4X5_EISA_TOTAL_SIZE, "de4x5")) {
i = 1; status = -EBUSY;
maxSlots = MAX_EISA_SLOTS; goto release_reg_1;
} else { /* Probe a specific location */
iobase = ioaddr;
i = (ioaddr >> 12);
maxSlots = i + 1;
} }
for (status = -ENODEV; (i<maxSlots) && (dev!=NULL); i++, iobase+=EISA_SLOT_INC) { if (!(dev = alloc_etherdev (sizeof (struct de4x5_private)))) {
if (check_region(iobase, DE4X5_EISA_TOTAL_SIZE)) continue; status = -ENOMEM;
if (!EISA_signature(name, EISA_ID)) continue; goto release_reg_2;
}
lp = dev->priv;
cfid = (u32) inl(PCI_CFID); cfid = (u32) inl(PCI_CFID);
cfrv = (u_short) inl(PCI_CFRV); lp->cfrv = (u_short) inl(PCI_CFRV);
device = (cfid >> 8) & 0x00ffff00; device = (cfid >> 8) & 0x00ffff00;
vendor = (u_short) cfid; vendor = (u_short) cfid;
/* Read the EISA Configuration Registers */ /* Read the EISA Configuration Registers */
irq = inb(EISA_REG0); regval = inb(EISA_REG0) & (ER0_INTL | ER0_INTT);
irq = de4x5_irq[(irq >> 1) & 0x03]; #ifdef CONFIG_ALPHA
/* Looks like the Jensen firmware (rev 2.2) doesn't really
* care about the EISA configuration, and thus doesn't
* configure the PLX bridge properly. Oh well... Simply mimic
* the EISA config file to sort it out. */
/* EISA REG1: Assert DecChip 21040 HW Reset */
outb (ER1_IAM | 1, EISA_REG1);
mdelay (1);
/* EISA REG1: Deassert DecChip 21040 HW Reset */
outb (ER1_IAM, EISA_REG1);
mdelay (1);
/* EISA REG3: R/W Burst Transfer Enable */
outb (ER3_BWE | ER3_BRE, EISA_REG3);
/* 32_bit slave/master, Preempt Time=23 bclks, Unlatched Interrupt */
outb (ER0_BSW | ER0_BMW | ER0_EPT | regval, EISA_REG0);
#endif
irq = de4x5_irq[(regval >> 1) & 0x03];
if (is_DC2114x) { if (is_DC2114x) {
device = ((cfrv & CFRV_RN) < DC2114x_BRK ? DC21142 : DC21143); device = ((lp->cfrv & CFRV_RN) < DC2114x_BRK ? DC21142 : DC21143);
} }
lp->chipset = device; lp->chipset = device;
lp->bus = EISA;
/* Write the PCI Configuration Registers */ /* Write the PCI Configuration Registers */
outl(PCI_COMMAND_IO | PCI_COMMAND_MASTER, PCI_CFCS); outl(PCI_COMMAND_IO | PCI_COMMAND_MASTER, PCI_CFCS);
outl(0x00006000, PCI_CFLT); outl(0x00006000, PCI_CFLT);
outl(iobase, PCI_CBIO); outl(iobase, PCI_CBIO);
DevicePresent(EISA_APROM); DevicePresent(dev, EISA_APROM);
dev->irq = irq; dev->irq = irq;
if ((status = de4x5_hw_init(dev, iobase, NULL)) == 0) {
num_de4x5s++; if (!(status = de4x5_hw_init (dev, iobase, gendev))) {
if (loading_module) link_modules(lastModule, dev); return 0;
lastEISA = i; }
return;
free_netdev (dev);
release_reg_2:
release_region (iobase + DE4X5_EISA_IO_PORTS, DE4X5_EISA_TOTAL_SIZE);
release_reg_1:
release_region (iobase, DE4X5_EISA_TOTAL_SIZE);
return status;
}
static int __devexit de4x5_eisa_remove (struct device *device)
{
struct net_device *dev;
u_long iobase;
dev = device->driver_data;
iobase = dev->base_addr;
unregister_netdev (dev);
free_netdev (dev);
release_region (iobase + DE4X5_EISA_IO_PORTS, DE4X5_EISA_TOTAL_SIZE);
release_region (iobase, DE4X5_EISA_TOTAL_SIZE);
return 0;
}
static struct eisa_device_id de4x5_eisa_ids[] = {
{ "DEC4250", 0 }, /* 0 is the board name index... */
{ "" }
};
static struct eisa_driver de4x5_eisa_driver = {
.id_table = de4x5_eisa_ids,
.driver = {
.name = "de4x5",
.probe = de4x5_eisa_probe,
.remove = __devexit_p (de4x5_eisa_remove),
} }
};
#endif
#ifdef CONFIG_PCI
/*
** This function searches the current bus (which is >0) for a DECchip with an
** SROM, so that in multiport cards that have one SROM shared between multiple
** DECchips, we can find the base SROM irrespective of the BIOS scan direction.
** For single port cards this is a time waster...
*/
static void __init
srom_search(struct net_device *dev, struct pci_dev *pdev)
{
u_char pb;
u_short vendor, status;
u_int irq = 0, device;
u_long iobase = 0; /* Clear upper 32 bits in Alphas */
int i, j, cfrv;
struct de4x5_private *lp = dev->priv;
struct list_head *walk = &pdev->bus_list;
for (walk = walk->next; walk != &pdev->bus_list; walk = walk->next) {
struct pci_dev *this_dev = pci_dev_b(walk);
/* Skip the pci_bus list entry */
if (list_entry(walk, struct pci_bus, devices) == pdev->bus) continue;
vendor = this_dev->vendor;
device = this_dev->device << 8;
if (!(is_DC21040 || is_DC21041 || is_DC21140 || is_DC2114x)) continue;
/* Get the chip configuration revision register */
pb = this_dev->bus->number;
pci_read_config_dword(this_dev, PCI_REVISION_ID, &cfrv);
/* Set the device number information */
lp->device = PCI_SLOT(this_dev->devfn);
lp->bus_num = pb;
/* Set the chipset information */
if (is_DC2114x) {
device = ((cfrv & CFRV_RN) < DC2114x_BRK ? DC21142 : DC21143);
} }
lp->chipset = device;
if (ioaddr == 0) lastEISA = i; /* Get the board I/O address (64 bits on sparc64) */
iobase = pci_resource_start(this_dev, 0);
/* Fetch the IRQ to be used */
irq = this_dev->irq;
if ((irq == 0) || (irq == 0xff) || ((int)irq == -1)) continue;
/* Check if I/O accesses are enabled */
pci_read_config_word(this_dev, PCI_COMMAND, &status);
if (!(status & PCI_COMMAND_IO)) continue;
/* Search for a valid SROM attached to this DECchip */
DevicePresent(dev, DE4X5_APROM);
for (j=0, i=0; i<ETH_ALEN; i++) {
j += (u_char) *((u_char *)&lp->srom + SROM_HWADD + i);
}
if ((j != 0) && (j != 0x5fa)) {
last.chipset = device;
last.bus = pb;
last.irq = irq;
for (i=0; i<ETH_ALEN; i++) {
last.addr[i] = (u_char)*((u_char *)&lp->srom + SROM_HWADD + i);
}
return;
}
}
return; return;
} }
#endif /* !(__sparc_v9__) && !(__powerpc__) && !defined(__alpha__) */
/* /*
** PCI bus I/O device probe ** PCI bus I/O device probe
...@@ -2169,56 +2212,57 @@ eisa_probe(struct net_device *dev, u_long ioaddr) ...@@ -2169,56 +2212,57 @@ eisa_probe(struct net_device *dev, u_long ioaddr)
** This function is only compatible with the *latest* 2.1.x kernels. For 2.0.x ** This function is only compatible with the *latest* 2.1.x kernels. For 2.0.x
** kernels use the V0.535[n] drivers. ** kernels use the V0.535[n] drivers.
*/ */
#define PCI_LAST_DEV 32
static void __init static int __init de4x5_pci_probe (struct pci_dev *pdev,
pci_probe(struct net_device *dev, u_long ioaddr) const struct pci_device_id *ent)
{ {
u_char pb, pbus, dev_num, dnum, timer; u_char pb, pbus = 0, dev_num, dnum = 0, timer;
u_short vendor, index, status; u_short vendor, status;
u_int irq = 0, device, class = DE4X5_CLASS_CODE; u_int irq = 0, device;
u_long iobase = 0; /* Clear upper 32 bits in Alphas */ u_long iobase = 0; /* Clear upper 32 bits in Alphas */
struct de4x5_bus_type *lp = &bus; int error;
struct net_device *dev;
if (lastPCI == NO_MORE_PCI) return; struct de4x5_private *lp;
lp->bus = PCI;
lp->bus_num = 0;
if ((ioaddr < 0x1000) && loading_module) {
pbus = (u_short)(ioaddr >> 8);
dnum = (u_short)(ioaddr & 0xff);
} else {
pbus = 0;
dnum = 0;
}
for (index=lastPCI+1;(pdev = pci_find_class(class, pdev))!=NULL;index++) {
dev_num = PCI_SLOT(pdev->devfn); dev_num = PCI_SLOT(pdev->devfn);
pb = pdev->bus->number; pb = pdev->bus->number;
if ((pbus || dnum) && ((pbus != pb) || (dnum != dev_num))) continue;
if (io) { /* probe a single PCI device */
pbus = (u_short)(io >> 8);
dnum = (u_short)(io & 0xff);
if ((pbus != pb) || (dnum != dev_num))
return -ENODEV;
}
vendor = pdev->vendor; vendor = pdev->vendor;
device = pdev->device << 8; device = pdev->device << 8;
if (!(is_DC21040 || is_DC21041 || is_DC21140 || is_DC2114x)) continue; if (!(is_DC21040 || is_DC21041 || is_DC21140 || is_DC2114x))
return -ENODEV;
/* Ok, the device seems to be for us. */
if (!(dev = alloc_etherdev (sizeof (struct de4x5_private))))
return -ENOMEM;
lp = dev->priv;
lp->bus = PCI;
lp->bus_num = 0;
/* Search for an SROM on this bus */ /* Search for an SROM on this bus */
if (lp->bus_num != pb) { if (lp->bus_num != pb) {
lp->bus_num = pb; lp->bus_num = pb;
srom_search(pdev); srom_search(dev, pdev);
} }
/* Get the chip configuration revision register */ /* Get the chip configuration revision register */
pci_read_config_dword(pdev, PCI_REVISION_ID, &cfrv); pci_read_config_dword(pdev, PCI_REVISION_ID, &lp->cfrv);
/* Set the device number information */ /* Set the device number information */
lp->device = dev_num; lp->device = dev_num;
lp->bus_num = pb; lp->bus_num = pb;
lp->pdev = pdev;
/* Set the chipset information */ /* Set the chipset information */
if (is_DC2114x) { if (is_DC2114x) {
device = ((cfrv & CFRV_RN) < DC2114x_BRK ? DC21142 : DC21143); device = ((lp->cfrv & CFRV_RN) < DC2114x_BRK ? DC21142 : DC21143);
} }
lp->chipset = device; lp->chipset = device;
...@@ -2227,7 +2271,10 @@ pci_probe(struct net_device *dev, u_long ioaddr) ...@@ -2227,7 +2271,10 @@ pci_probe(struct net_device *dev, u_long ioaddr)
/* Fetch the IRQ to be used */ /* Fetch the IRQ to be used */
irq = pdev->irq; irq = pdev->irq;
if ((irq == 0) || (irq == 0xff) || ((int)irq == -1)) continue; if ((irq == 0) || (irq == 0xff) || ((int)irq == -1)) {
error = -ENODEV;
goto free_dev;
}
/* Check if I/O accesses and Bus Mastering are enabled */ /* Check if I/O accesses and Bus Mastering are enabled */
pci_read_config_word(pdev, PCI_COMMAND, &status); pci_read_config_word(pdev, PCI_COMMAND, &status);
...@@ -2238,14 +2285,20 @@ pci_probe(struct net_device *dev, u_long ioaddr) ...@@ -2238,14 +2285,20 @@ pci_probe(struct net_device *dev, u_long ioaddr)
pci_read_config_word(pdev, PCI_COMMAND, &status); pci_read_config_word(pdev, PCI_COMMAND, &status);
} }
#endif /* __powerpc__ */ #endif /* __powerpc__ */
if (!(status & PCI_COMMAND_IO)) continue; if (!(status & PCI_COMMAND_IO)) {
error = -ENODEV;
goto free_dev;
}
if (!(status & PCI_COMMAND_MASTER)) { if (!(status & PCI_COMMAND_MASTER)) {
status |= PCI_COMMAND_MASTER; status |= PCI_COMMAND_MASTER;
pci_write_config_word(pdev, PCI_COMMAND, status); pci_write_config_word(pdev, PCI_COMMAND, status);
pci_read_config_word(pdev, PCI_COMMAND, &status); pci_read_config_word(pdev, PCI_COMMAND, &status);
} }
if (!(status & PCI_COMMAND_MASTER)) continue; if (!(status & PCI_COMMAND_MASTER)) {
error = -ENODEV;
goto free_dev;
}
/* Check the latency timer for values >= 0x60 */ /* Check the latency timer for values >= 0x60 */
pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &timer); pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &timer);
...@@ -2253,116 +2306,61 @@ pci_probe(struct net_device *dev, u_long ioaddr) ...@@ -2253,116 +2306,61 @@ pci_probe(struct net_device *dev, u_long ioaddr)
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x60); pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x60);
} }
DevicePresent(DE4X5_APROM); DevicePresent(dev, DE4X5_APROM);
if (check_region(iobase, DE4X5_PCI_TOTAL_SIZE) == 0) {
dev->irq = irq;
if ((status = de4x5_hw_init(dev, iobase, pdev)) == 0) {
num_de4x5s++;
lastPCI = index;
if (loading_module) link_modules(lastModule, dev);
return;
}
} else if (ioaddr != 0) {
printk("%s: region already allocated at 0x%04lx.\n", dev->name,
iobase);
}
}
lastPCI = NO_MORE_PCI; if (!request_region (iobase, DE4X5_PCI_TOTAL_SIZE, "de4x5")) {
error = -EBUSY;
return; goto free_dev;
}
/*
** This function searches the current bus (which is >0) for a DECchip with an
** SROM, so that in multiport cards that have one SROM shared between multiple
** DECchips, we can find the base SROM irrespective of the BIOS scan direction.
** For single port cards this is a time waster...
*/
static void __init
srom_search(struct pci_dev *dev)
{
u_char pb;
u_short vendor, status;
u_int irq = 0, device;
u_long iobase = 0; /* Clear upper 32 bits in Alphas */
int i, j;
struct de4x5_bus_type *lp = &bus;
struct list_head *walk = &dev->bus_list;
for (walk = walk->next; walk != &dev->bus_list; walk = walk->next) {
struct pci_dev *this_dev = pci_dev_b(walk);
/* Skip the pci_bus list entry */
if (list_entry(walk, struct pci_bus, devices) == dev->bus) continue;
vendor = this_dev->vendor;
device = this_dev->device << 8;
if (!(is_DC21040 || is_DC21041 || is_DC21140 || is_DC2114x)) continue;
/* Get the chip configuration revision register */
pb = this_dev->bus->number;
pci_read_config_dword(this_dev, PCI_REVISION_ID, &cfrv);
/* Set the device number information */
lp->device = PCI_SLOT(this_dev->devfn);
lp->bus_num = pb;
/* Set the chipset information */
if (is_DC2114x) {
device = ((cfrv & CFRV_RN) < DC2114x_BRK ? DC21142 : DC21143);
} }
lp->chipset = device;
/* Get the board I/O address (64 bits on sparc64) */
iobase = pci_resource_start(this_dev, 0);
/* Fetch the IRQ to be used */
irq = this_dev->irq;
if ((irq == 0) || (irq == 0xff) || ((int)irq == -1)) continue;
/* Check if I/O accesses are enabled */ dev->irq = irq;
pci_read_config_word(this_dev, PCI_COMMAND, &status);
if (!(status & PCI_COMMAND_IO)) continue;
/* Search for a valid SROM attached to this DECchip */ if ((error = de4x5_hw_init(dev, iobase, &pdev->dev))) {
DevicePresent(DE4X5_APROM); goto release;
for (j=0, i=0; i<ETH_ALEN; i++) {
j += (u_char) *((u_char *)&lp->srom + SROM_HWADD + i);
}
if ((j != 0) && (j != 0x5fa)) {
last.chipset = device;
last.bus = pb;
last.irq = irq;
for (i=0; i<ETH_ALEN; i++) {
last.addr[i] = (u_char)*((u_char *)&lp->srom + SROM_HWADD + i);
}
return;
}
} }
return; return 0;
release:
release_region (iobase, DE4X5_PCI_TOTAL_SIZE);
free_dev:
free_netdev (dev);
return error;
} }
static void __init static void __devexit de4x5_pci_remove (struct pci_dev *pdev)
link_modules(struct net_device *dev, struct net_device *tmp)
{ {
struct net_device *p=dev; struct net_device *dev;
u_long iobase;
if (p) { dev = pdev->dev.driver_data;
while (((struct de4x5_private *)(p->priv))->next_module) { iobase = dev->base_addr;
p = ((struct de4x5_private *)(p->priv))->next_module;
}
if (dev != tmp) { unregister_netdev (dev);
((struct de4x5_private *)(p->priv))->next_module = tmp; free_netdev (dev);
} else { release_region (iobase, DE4X5_PCI_TOTAL_SIZE);
((struct de4x5_private *)(p->priv))->next_module = NULL; }
}
} static struct pci_device_id de4x5_pci_tbl[] = {
{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP_PLUS,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP_FAST,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2 },
{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
{ },
};
return; static struct pci_driver de4x5_pci_driver = {
} .name = "de4x5",
.id_table = de4x5_pci_tbl,
.probe = de4x5_pci_probe,
.remove = __devexit_p (de4x5_pci_remove),
};
#endif
/* /*
** Auto configure the media here rather than setting the port at compile ** Auto configure the media here rather than setting the port at compile
...@@ -3945,32 +3943,18 @@ create_packet(struct net_device *dev, char *frame, int len) ...@@ -3945,32 +3943,18 @@ create_packet(struct net_device *dev, char *frame, int len)
** Look for a particular board name in the EISA configuration space ** Look for a particular board name in the EISA configuration space
*/ */
static int static int
EISA_signature(char *name, s32 eisa_id) EISA_signature(char *name, struct device *device)
{ {
static c_char *signatures[] = DE4X5_SIGNATURE; int i, status = 0, siglen = sizeof(de4x5_signatures)/sizeof(c_char *);
char ManCode[DE4X5_STRLEN]; struct eisa_device *edev;
union {
s32 ID;
char Id[4];
} Eisa;
int i, status = 0, siglen = sizeof(signatures)/sizeof(c_char *);
*name = '\0'; *name = '\0';
Eisa.ID = inl(eisa_id); edev = to_eisa_device (device);
i = edev->id.driver_data;
ManCode[0]=(((Eisa.Id[0]>>2)&0x1f)+0x40);
ManCode[1]=(((Eisa.Id[1]&0xe0)>>5)+((Eisa.Id[0]&0x03)<<3)+0x40); if (i >= 0 && i < siglen) {
ManCode[2]=(((Eisa.Id[2]>>4)&0x0f)+0x30); strcpy (name, de4x5_signatures[i]);
ManCode[3]=((Eisa.Id[2]&0x0f)+0x30);
ManCode[4]=(((Eisa.Id[3]>>4)&0x0f)+0x30);
ManCode[5]='\0';
for (i=0;i<siglen;i++) {
if (strstr(ManCode, signatures[i]) != NULL) {
strcpy(name,ManCode);
status = 1; status = 1;
break;
}
} }
return status; /* return the device name string */ return status; /* return the device name string */
...@@ -3980,9 +3964,8 @@ EISA_signature(char *name, s32 eisa_id) ...@@ -3980,9 +3964,8 @@ EISA_signature(char *name, s32 eisa_id)
** Look for a particular board name in the PCI configuration space ** Look for a particular board name in the PCI configuration space
*/ */
static int static int
PCI_signature(char *name, struct de4x5_bus_type *lp) PCI_signature(char *name, struct de4x5_private *lp)
{ {
static c_char *de4x5_signatures[] = DE4X5_SIGNATURE;
int i, status = 0, siglen = sizeof(de4x5_signatures)/sizeof(c_char *); int i, status = 0, siglen = sizeof(de4x5_signatures)/sizeof(c_char *);
if (lp->chipset == DC21040) { if (lp->chipset == DC21040) {
...@@ -4008,10 +3991,10 @@ PCI_signature(char *name, struct de4x5_bus_type *lp) ...@@ -4008,10 +3991,10 @@ PCI_signature(char *name, struct de4x5_bus_type *lp)
))))))); )))))));
} }
if (lp->chipset != DC21041) { if (lp->chipset != DC21041) {
useSROM = TRUE; /* card is not recognisably DEC */ lp->useSROM = TRUE; /* card is not recognisably DEC */
} }
} else if ((lp->chipset & ~0x00ff) == DC2114x) { } else if ((lp->chipset & ~0x00ff) == DC2114x) {
useSROM = TRUE; lp->useSROM = TRUE;
} }
return status; return status;
...@@ -4026,10 +4009,10 @@ PCI_signature(char *name, struct de4x5_bus_type *lp) ...@@ -4026,10 +4009,10 @@ PCI_signature(char *name, struct de4x5_bus_type *lp)
** be fixed up later). ** be fixed up later).
*/ */
static void static void
DevicePresent(u_long aprom_addr) DevicePresent(struct net_device *dev, u_long aprom_addr)
{ {
int i, j=0; int i, j=0;
struct de4x5_bus_type *lp = &bus; struct de4x5_private *lp = (struct de4x5_private *) dev->priv;
if (lp->chipset == DC21040) { if (lp->chipset == DC21040) {
if (lp->bus == EISA) { if (lp->bus == EISA) {
...@@ -4110,7 +4093,7 @@ get_hw_addr(struct net_device *dev) ...@@ -4110,7 +4093,7 @@ get_hw_addr(struct net_device *dev)
u_long iobase = dev->base_addr; u_long iobase = dev->base_addr;
int broken, i, k, tmp, status = 0; int broken, i, k, tmp, status = 0;
u_short j,chksum; u_short j,chksum;
struct de4x5_bus_type *lp = &bus; struct de4x5_private *lp = dev->priv;
broken = de4x5_bad_srom(lp); broken = de4x5_bad_srom(lp);
...@@ -4191,7 +4174,7 @@ get_hw_addr(struct net_device *dev) ...@@ -4191,7 +4174,7 @@ get_hw_addr(struct net_device *dev)
** didn't seem to work here...? ** didn't seem to work here...?
*/ */
static int static int
de4x5_bad_srom(struct de4x5_bus_type *lp) de4x5_bad_srom(struct de4x5_private *lp)
{ {
int i, status = 0; int i, status = 0;
...@@ -4225,14 +4208,14 @@ de4x5_strncmp(char *a, char *b, int n) ...@@ -4225,14 +4208,14 @@ de4x5_strncmp(char *a, char *b, int n)
static void static void
srom_repair(struct net_device *dev, int card) srom_repair(struct net_device *dev, int card)
{ {
struct de4x5_bus_type *lp = &bus; struct de4x5_private *lp = dev->priv;
switch(card) { switch(card) {
case SMC: case SMC:
memset((char *)&bus.srom, 0, sizeof(struct de4x5_srom)); memset((char *)&lp->srom, 0, sizeof(struct de4x5_srom));
memcpy(lp->srom.ieee_addr, (char *)dev->dev_addr, ETH_ALEN); memcpy(lp->srom.ieee_addr, (char *)dev->dev_addr, ETH_ALEN);
memcpy(lp->srom.info, (char *)&srom_repair_info[SMC-1], 100); memcpy(lp->srom.info, (char *)&srom_repair_info[SMC-1], 100);
useSROM = TRUE; lp->useSROM = TRUE;
break; break;
} }
...@@ -4246,7 +4229,7 @@ srom_repair(struct net_device *dev, int card) ...@@ -4246,7 +4229,7 @@ srom_repair(struct net_device *dev, int card)
static int static int
test_bad_enet(struct net_device *dev, int status) test_bad_enet(struct net_device *dev, int status)
{ {
struct de4x5_bus_type *lp = &bus; struct de4x5_private *lp = dev->priv;
int i, tmp; int i, tmp;
for (tmp=0,i=0; i<ETH_ALEN; i++) tmp += (u_char)dev->dev_addr[i]; for (tmp=0,i=0; i<ETH_ALEN; i++) tmp += (u_char)dev->dev_addr[i];
...@@ -4279,7 +4262,7 @@ test_bad_enet(struct net_device *dev, int status) ...@@ -4279,7 +4262,7 @@ test_bad_enet(struct net_device *dev, int status)
** List of board exceptions with correctly wired IRQs ** List of board exceptions with correctly wired IRQs
*/ */
static int static int
an_exception(struct de4x5_bus_type *lp) an_exception(struct de4x5_private *lp)
{ {
if ((*(u_short *)lp->srom.sub_vendor_id == 0x00c0) && if ((*(u_short *)lp->srom.sub_vendor_id == 0x00c0) &&
(*(u_short *)lp->srom.sub_system_id == 0x95e0)) { (*(u_short *)lp->srom.sub_system_id == 0x95e0)) {
...@@ -5312,19 +5295,20 @@ yawn(struct net_device *dev, int state) ...@@ -5312,19 +5295,20 @@ yawn(struct net_device *dev, int state)
break; break;
} }
} else { } else {
struct pci_dev *pdev = to_pci_dev (lp->gendev);
switch(state) { switch(state) {
case WAKEUP: case WAKEUP:
pci_write_config_byte(lp->pdev, PCI_CFDA_PSM, WAKEUP); pci_write_config_byte(pdev, PCI_CFDA_PSM, WAKEUP);
mdelay(10); mdelay(10);
break; break;
case SNOOZE: case SNOOZE:
pci_write_config_byte(lp->pdev, PCI_CFDA_PSM, SNOOZE); pci_write_config_byte(pdev, PCI_CFDA_PSM, SNOOZE);
break; break;
case SLEEP: case SLEEP:
outl(0, DE4X5_SICR); outl(0, DE4X5_SICR);
pci_write_config_byte(lp->pdev, PCI_CFDA_PSM, SLEEP); pci_write_config_byte(pdev, PCI_CFDA_PSM, SLEEP);
break; break;
} }
} }
...@@ -5348,9 +5332,6 @@ de4x5_parse_params(struct net_device *dev) ...@@ -5348,9 +5332,6 @@ de4x5_parse_params(struct net_device *dev)
t = *q; t = *q;
*q = '\0'; *q = '\0';
#if !defined(__sparc_v9__) && !defined(__powerpc__) && !defined(__alpha__)
if (strstr(p, "force_eisa") || strstr(p, "FORCE_EISA")) forceEISA = 1;
#endif
if (strstr(p, "fdx") || strstr(p, "FDX")) lp->params.fdx = 1; if (strstr(p, "fdx") || strstr(p, "FDX")) lp->params.fdx = 1;
if (strstr(p, "autosense") || strstr(p, "AUTOSENSE")) { if (strstr(p, "autosense") || strstr(p, "AUTOSENSE")) {
...@@ -5758,146 +5739,29 @@ de4x5_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) ...@@ -5758,146 +5739,29 @@ de4x5_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
return status; return status;
} }
#ifdef MODULE static int __init de4x5_module_init (void)
/*
** Note now that module autoprobing is allowed under EISA and PCI. The
** IRQ lines will not be auto-detected; instead I'll rely on the BIOSes
** to "do the right thing".
*/
#define LP(a) ((struct de4x5_private *)(a))
static struct net_device *mdev = NULL;
static int io=0x0;/* EDIT THIS LINE FOR YOUR CONFIGURATION IF NEEDED */
MODULE_PARM(io, "i");
MODULE_PARM_DESC(io, "de4x5 I/O base address");
int
init_module(void)
{
int i, num, status = -EIO;
struct net_device *p;
num = count_adapters();
for (i=0; i<num; i++) {
if ((p = insert_device(NULL, io, de4x5_probe)) == NULL)
return -ENOMEM;
if (!mdev) mdev = p;
if (register_netdev(p) != 0) {
struct de4x5_private *lp = (struct de4x5_private *)p->priv;
if (lp) {
release_region(p->base_addr, (lp->bus == PCI ?
DE4X5_PCI_TOTAL_SIZE :
DE4X5_EISA_TOTAL_SIZE));
if (lp->cache.priv) { /* Private area allocated? */
kfree(lp->cache.priv); /* Free the private area */
}
if (lp->rx_ring) {
pci_free_consistent(lp->pdev, lp->dma_size, lp->rx_ring,
lp->dma_rings);
}
}
kfree(p);
} else {
status = 0; /* At least one adapter will work */
lastModule = p;
}
}
return status;
}
void
cleanup_module(void)
{
while (mdev != NULL) {
mdev = unlink_modules(mdev);
}
return;
}
static struct net_device *
unlink_modules(struct net_device *p)
{ {
struct net_device *next = NULL; int err = 0;
if (p->priv) { /* Private areas allocated? */
struct de4x5_private *lp = (struct de4x5_private *)p->priv;
next = lp->next_module;
if (lp->rx_ring) {
pci_free_consistent(lp->pdev, lp->dma_size, lp->rx_ring,
lp->dma_rings);
}
release_region(p->base_addr, (lp->bus == PCI ?
DE4X5_PCI_TOTAL_SIZE :
DE4X5_EISA_TOTAL_SIZE));
kfree(lp->cache.priv); /* Free the private area */
}
unregister_netdev(p);
free_netdev(p); /* Free the device structure */
return next;
}
static int
count_adapters(void)
{
int i, j=0;
u_short vendor;
u_int class = DE4X5_CLASS_CODE;
u_int device;
#if !defined(__sparc_v9__) && !defined(__powerpc__) && !defined(__alpha__)
char name[DE4X5_STRLEN];
u_long iobase = 0x1000;
for (i=1; i<MAX_EISA_SLOTS; i++, iobase+=EISA_SLOT_INC) { #if CONFIG_PCI
if (EISA_signature(name, EISA_ID)) j++; err = pci_module_init (&de4x5_pci_driver);
} #endif
#ifdef CONFIG_EISA
err |= eisa_driver_register (&de4x5_eisa_driver);
#endif #endif
for (i=0; (pdev=pci_find_class(class, pdev))!= NULL; i++) { return err;
vendor = pdev->vendor;
device = pdev->device << 8;
if (is_DC21040 || is_DC21041 || is_DC21140 || is_DC2114x) j++;
}
return j;
} }
/* static void __exit de4x5_module_exit (void)
** If at end of eth device list and can't use current entry, malloc
** one up. If memory could not be allocated, print an error message.
*/
static struct net_device * __init
insert_device(struct net_device *dev, u_long iobase, int (*init)(struct net_device *))
{ {
struct net_device *new; #if CONFIG_PCI
pci_unregister_driver (&de4x5_pci_driver);
new = (struct net_device *)kmalloc(sizeof(struct net_device), GFP_KERNEL); #endif
if (new == NULL) { #ifdef CONFIG_EISA
printk("de4x5.c: Device not initialised, insufficient memory\n"); eisa_driver_unregister (&de4x5_eisa_driver);
return NULL; #endif
} else {
memset((char *)new, 0, sizeof(struct net_device));
new->base_addr = iobase; /* assign the io address */
new->init = init; /* initialisation routine */
}
return new;
} }
#endif /* MODULE */ module_init (de4x5_module_init);
module_exit (de4x5_module_exit);
/*
* Local variables:
*
* Delete -DMODVERSIONS below if you didn't define this in your kernel
*
* compile-command: "gcc -D__KERNEL__ -DMODULE -I/linux/include -Wall -Wstrict-prototypes -fomit-frame-pointer -fno-strength-reduce -malign-loops=2 -malign-jumps=2 -malign-functions=2 -O2 -m486 -DMODVERSIONS -include /linux/include/linux/modversions.h -c de4x5.c"
* End:
*/
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7