Blackfin: drop unused SL811 platform resources from bf527/pnav boards

These platforms don't hook up to this USB controller, so no point in
declaring resources for it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

arch/blackfin/mach-bf527/boards/cm_bf527.c

@@ -18,7 +18,6 @@
 #include <linux/i2c.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
-#include <linux/usb/sl811.h>
 #include <linux/usb/musb.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
@@ -270,50 +269,6 @@ static struct platform_device dm9000_device = {
 };
 #endif
 
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-static struct resource sl811_hcd_resources[] = {
-	{
-		.start = 0x20340000,
-		.end = 0x20340000,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = 0x20340004,
-		.end = 0x20340004,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = CONFIG_USB_SL811_BFIN_IRQ,
-		.end = CONFIG_USB_SL811_BFIN_IRQ,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-	},
-};
-
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-void sl811_port_power(struct device *dev, int is_on)
-{
-	gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
-	gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
-}
-#endif
-
-static struct sl811_platform_data sl811_priv = {
-	.potpg = 10,
-	.power = 250,       /* == 500mA */
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-	.port_power = &sl811_port_power,
-#endif
-};
-
-static struct platform_device sl811_hcd_device = {
-	.name = "sl811-hcd",
-	.id = 0,
-	.dev = {
-		.platform_data = &sl811_priv,
-	},
-	.num_resources = ARRAY_SIZE(sl811_hcd_resources),
-	.resource = sl811_hcd_resources,
-};
-#endif
-
 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 static struct platform_device bfin_mii_bus = {
 	.name = "bfin_mii_bus",
@@ -929,10 +884,6 @@ static struct platform_device *cmbf527_devices[] __initdata = {
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-	&sl811_hcd_device,
-#endif
-
 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
 	&bfin_isp1760_device,
 #endif

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -16,7 +16,6 @@
 #include <linux/i2c.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
-#include <linux/usb/sl811.h>
 #include <linux/usb/musb.h>
 #include <linux/leds.h>
 #include <linux/input.h>
@@ -359,50 +358,6 @@ static struct platform_device dm9000_device = {
 };
 #endif
 
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-static struct resource sl811_hcd_resources[] = {
-	{
-		.start = 0x20340000,
-		.end = 0x20340000,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = 0x20340004,
-		.end = 0x20340004,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = CONFIG_USB_SL811_BFIN_IRQ,
-		.end = CONFIG_USB_SL811_BFIN_IRQ,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-	},
-};
-
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-void sl811_port_power(struct device *dev, int is_on)
-{
-	gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
-	gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
-}
-#endif
-
-static struct sl811_platform_data sl811_priv = {
-	.potpg = 10,
-	.power = 250,       /* == 500mA */
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-	.port_power = &sl811_port_power,
-#endif
-};
-
-static struct platform_device sl811_hcd_device = {
-	.name = "sl811-hcd",
-	.id = 0,
-	.dev = {
-		.platform_data = &sl811_priv,
-	},
-	.num_resources = ARRAY_SIZE(sl811_hcd_resources),
-	.resource = sl811_hcd_resources,
-};
-#endif
-
 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 static struct platform_device bfin_mii_bus = {
 	.name = "bfin_mii_bus",
@@ -1113,10 +1068,6 @@ static struct platform_device *stamp_devices[] __initdata = {
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-	&sl811_hcd_device,
-#endif
-
 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
 	&bfin_isp1760_device,
 #endif

arch/blackfin/mach-bf537/boards/pnav10.c

@@ -17,7 +17,6 @@
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
-#include <linux/usb/sl811.h>
 
 #include <linux/spi/ad7877.h>
 
@@ -99,51 +98,6 @@ static struct platform_device smc91x_device = {
 };
 #endif
 
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-static struct resource sl811_hcd_resources[] = {
-	{
-		.start = 0x20340000,
-		.end = 0x20340000,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = 0x20340004,
-		.end = 0x20340004,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = CONFIG_USB_SL811_BFIN_IRQ,
-		.end = CONFIG_USB_SL811_BFIN_IRQ,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-	},
-};
-
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-void sl811_port_power(struct device *dev, int is_on)
-{
-	gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
-	gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
-
-}
-#endif
-
-static struct sl811_platform_data sl811_priv = {
-	.potpg = 10,
-	.power = 250,       /* == 500mA */
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-	.port_power = &sl811_port_power,
-#endif
-};
-
-static struct platform_device sl811_hcd_device = {
-	.name = "sl811-hcd",
-	.id = 0,
-	.dev = {
-		.platform_data = &sl811_priv,
-	},
-	.num_resources = ARRAY_SIZE(sl811_hcd_resources),
-	.resource = sl811_hcd_resources,
-};
-#endif
-
 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 static struct platform_device bfin_mii_bus = {
 	.name = "bfin_mii_bus",
@@ -514,10 +468,6 @@ static struct platform_device *stamp_devices[] __initdata = {
 	&rtc_device,
 #endif
 
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-	&sl811_hcd_device,
-#endif
-
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 	&smc91x_device,
 #endif