Merge branch 'misc' into for-linus

Documentation/scsi/g_NCR5380.txt

@@ -6,17 +6,15 @@ NCR53c400 extensions (c) 1994,1995,1996 Kevin Lentin
 This file documents the NCR53c400 extensions by Kevin Lentin and some
 enhancements to the NCR5380 core.
 
-This driver supports both NCR5380 and NCR53c400 cards in port or memory
-mapped modes. Currently this driver can only support one of those mapping
-modes at a time but it does support both of these chips at the same time.
-The next release of this driver will support port & memory mapped cards at
-the same time. It should be able to handle multiple different cards in the
-same machine.
+This driver supports NCR5380 and NCR53c400 and compatible cards in port or
+memory mapped modes.
 
-The drivers/scsi/Makefile has an override in it for the most common
-NCR53c400 card, the Trantor T130B in its default configuration:
-	Port: 0x350
-	IRQ : 5
+Use of an interrupt is recommended, if supported by the board, as this will
+allow targets to disconnect and thereby improve SCSI bus utilization.
+
+If the irq parameter is 254 or is omitted entirely, the driver will probe
+for the correct IRQ line automatically. If the irq parameter is 0 or 255
+then no IRQ will be used.
 
 The NCR53c400 does not support DMA but it does have Pseudo-DMA which is
 supported by the driver.
@@ -47,22 +45,24 @@ These old-style parameters can support only one card:
   dtc_3181e=1  to set up for a Domex Technology Corp 3181E board
   hp_c2502=1   to set up for a Hewlett Packard C2502 board
 
-e.g.
-OLD: modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1
-NEW: modprobe g_NCR5380 irq=5 base=0x350 card=0
-  for a port mapped NCR5380 board or
-
-OLD: modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
-NEW: modprobe g_NCR5380 irq=255 base=0xc8000 card=1
-  for a memory mapped NCR53C400 board with interrupts disabled or
+E.g. Trantor T130B in its default configuration:
+modprobe g_NCR5380 irq=5 base=0x350 card=1
+or alternatively, using the old syntax,
+modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_53c400=1
 
-NEW: modprobe g_NCR5380 irq=0,7 base=0x240,0x300 card=3,4
-  for two cards: DTC3181 (in non-PnP mode) at 0x240 with no IRQ
-             and HP C2502 at 0x300 with IRQ 7
+E.g. a port mapped NCR5380 board, driver to probe for IRQ:
+modprobe g_NCR5380 base=0x350 card=0
+or alternatively,
+modprobe g_NCR5380 ncr_addr=0x350 ncr_5380=1
 
-(255 should be specified for no or DMA interrupt, 254 to autoprobe for an 
-     IRQ line if overridden on the command line.)
+E.g. a memory mapped NCR53C400 board with no IRQ:
+modprobe g_NCR5380 irq=255 base=0xc8000 card=1
+or alternatively,
+modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
 
+E.g. two cards, DTC3181 (in non-PnP mode) at 0x240 with no IRQ
+and HP C2502 at 0x300 with IRQ 7:
+modprobe g_NCR5380 irq=0,7 base=0x240,0x300 card=3,4
 
 Kevin Lentin
 K.Lentin@cs.monash.edu.au

drivers/scsi/NCR5380.c

@@ -97,9 +97,6 @@
  * and macros and include this file in your driver.
  *
  * These macros control options :
- * AUTOPROBE_IRQ - if defined, the NCR5380_probe_irq() function will be
- * defined.
- *
  * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
  * for commands that return with a CHECK CONDITION status.
  *
@@ -127,9 +124,7 @@
  * NCR5380_dma_residual   - residual byte count
  *
  * The generic driver is initialized by calling NCR5380_init(instance),
- * after setting the appropriate host specific fields and ID.  If the
- * driver wishes to autoprobe for an IRQ line, the NCR5380_probe_irq(instance,
- * possible) function may be used.
+ * after setting the appropriate host specific fields and ID.
  */
 
 #ifndef NCR5380_io_delay
@@ -351,76 +346,6 @@ static void NCR5380_print_phase(struct Scsi_Host *instance)
 }
 #endif
 
-
-static int probe_irq;
-
-/**
- * probe_intr	-	helper for IRQ autoprobe
- * @irq: interrupt number
- * @dev_id: unused
- * @regs: unused
- *
- * Set a flag to indicate the IRQ in question was received. This is
- * used by the IRQ probe code.
- */
-
-static irqreturn_t probe_intr(int irq, void *dev_id)
-{
-	probe_irq = irq;
-	return IRQ_HANDLED;
-}
-
-/**
- * NCR5380_probe_irq	-	find the IRQ of an NCR5380
- * @instance: NCR5380 controller
- * @possible: bitmask of ISA IRQ lines
- *
- * Autoprobe for the IRQ line used by the NCR5380 by triggering an IRQ
- * and then looking to see what interrupt actually turned up.
- */
-
-static int __maybe_unused NCR5380_probe_irq(struct Scsi_Host *instance,
-						int possible)
-{
-	struct NCR5380_hostdata *hostdata = shost_priv(instance);
-	unsigned long timeout;
-	int trying_irqs, i, mask;
-
-	for (trying_irqs = 0, i = 1, mask = 2; i < 16; ++i, mask <<= 1)
-		if ((mask & possible) && (request_irq(i, &probe_intr, 0, "NCR-probe", NULL) == 0))
-			trying_irqs |= mask;
-
-	timeout = jiffies + msecs_to_jiffies(250);
-	probe_irq = NO_IRQ;
-
-	/*
-	 * A interrupt is triggered whenever BSY = false, SEL = true
-	 * and a bit set in the SELECT_ENABLE_REG is asserted on the
-	 * SCSI bus.
-	 *
-	 * Note that the bus is only driven when the phase control signals
-	 * (I/O, C/D, and MSG) match those in the TCR, so we must reset that
-	 * to zero.
-	 */
-
-	NCR5380_write(TARGET_COMMAND_REG, 0);
-	NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA | ICR_ASSERT_SEL);
-
-	while (probe_irq == NO_IRQ && time_before(jiffies, timeout))
-		schedule_timeout_uninterruptible(1);
-
-	NCR5380_write(SELECT_ENABLE_REG, 0);
-	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-
-	for (i = 1, mask = 2; i < 16; ++i, mask <<= 1)
-		if (trying_irqs & mask)
-			free_irq(i, NULL);
-
-	return probe_irq;
-}
-
 /**
  * NCR58380_info - report driver and host information
  * @instance: relevant scsi host instance

drivers/scsi/NCR5380.h

@@ -199,16 +199,6 @@
 
 #define PHASE_SR_TO_TCR(phase) ((phase) >> 2)
 
-/*
- * These are "special" values for the irq and dma_channel fields of the 
- * Scsi_Host structure
- */
-
-#define DMA_NONE	255
-#define IRQ_AUTO	254
-#define DMA_AUTO	254
-#define PORT_AUTO	0xffff	/* autoprobe io port for 53c400a */
-
 #ifndef NO_IRQ
 #define NO_IRQ		0
 #endif
@@ -290,7 +280,6 @@ static void NCR5380_print(struct Scsi_Host *instance);
 #define NCR5380_dprint_phase(flg, arg) do {} while (0)
 #endif
 
-static int NCR5380_probe_irq(struct Scsi_Host *instance, int possible);
 static int NCR5380_init(struct Scsi_Host *instance, int flags);
 static int NCR5380_maybe_reset_bus(struct Scsi_Host *);
 static void NCR5380_exit(struct Scsi_Host *instance);

drivers/scsi/aacraid/linit.c

@@ -160,7 +160,6 @@ static const struct pci_device_id aac_pci_tbl[] = {
 	{ 0x9005, 0x028b, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 62 }, /* Adaptec PMC Series 6 (Tupelo) */
 	{ 0x9005, 0x028c, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 63 }, /* Adaptec PMC Series 7 (Denali) */
 	{ 0x9005, 0x028d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 64 }, /* Adaptec PMC Series 8 */
-	{ 0x9005, 0x028f, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 65 }, /* Adaptec PMC Series 9 */
 	{ 0,}
 };
 MODULE_DEVICE_TABLE(pci, aac_pci_tbl);
@@ -239,7 +238,6 @@ static struct aac_driver_ident aac_drivers[] = {
 	{ aac_src_init, "aacraid", "ADAPTEC ", "RAID            ", 2, AAC_QUIRK_SRC }, /* Adaptec PMC Series 6 (Tupelo) */
 	{ aac_srcv_init, "aacraid", "ADAPTEC ", "RAID            ", 2, AAC_QUIRK_SRC }, /* Adaptec PMC Series 7 (Denali) */
 	{ aac_srcv_init, "aacraid", "ADAPTEC ", "RAID            ", 2, AAC_QUIRK_SRC }, /* Adaptec PMC Series 8 */
-	{ aac_srcv_init, "aacraid", "ADAPTEC ", "RAID            ", 2, AAC_QUIRK_SRC } /* Adaptec PMC Series 9 */
 };
 
 /**

drivers/scsi/g_NCR5380.c

@@ -37,7 +37,7 @@
 #define MAX_CARDS 8
 
 /* old-style parameters for compatibility */
-static int ncr_irq;
+static int ncr_irq = -1;
 static int ncr_addr;
 static int ncr_5380;
 static int ncr_53c400;
@@ -52,9 +52,9 @@ module_param(ncr_53c400a, int, 0);
 module_param(dtc_3181e, int, 0);
 module_param(hp_c2502, int, 0);
 
-static int irq[] = { 0, 0, 0, 0, 0, 0, 0, 0 };
+static int irq[] = { -1, -1, -1, -1, -1, -1, -1, -1 };
 module_param_array(irq, int, NULL, 0);
-MODULE_PARM_DESC(irq, "IRQ number(s)");
+MODULE_PARM_DESC(irq, "IRQ number(s) (0=none, 254=auto [default])");
 
 static int base[] = { 0, 0, 0, 0, 0, 0, 0, 0 };
 module_param_array(base, int, NULL, 0);
@@ -67,6 +67,56 @@ MODULE_PARM_DESC(card, "card type (0=NCR5380, 1=NCR53C400, 2=NCR53C400A, 3=DTC31
 MODULE_ALIAS("g_NCR5380_mmio");
 MODULE_LICENSE("GPL");
 
+static void g_NCR5380_trigger_irq(struct Scsi_Host *instance)
+{
+	struct NCR5380_hostdata *hostdata = shost_priv(instance);
+
+	/*
+	 * An interrupt is triggered whenever BSY = false, SEL = true
+	 * and a bit set in the SELECT_ENABLE_REG is asserted on the
+	 * SCSI bus.
+	 *
+	 * Note that the bus is only driven when the phase control signals
+	 * (I/O, C/D, and MSG) match those in the TCR.
+	 */
+	NCR5380_write(TARGET_COMMAND_REG,
+	              PHASE_SR_TO_TCR(NCR5380_read(STATUS_REG) & PHASE_MASK));
+	NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
+	NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
+	NCR5380_write(INITIATOR_COMMAND_REG,
+	              ICR_BASE | ICR_ASSERT_DATA | ICR_ASSERT_SEL);
+
+	msleep(1);
+
+	NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
+	NCR5380_write(SELECT_ENABLE_REG, 0);
+	NCR5380_write(TARGET_COMMAND_REG, 0);
+}
+
+/**
+ * g_NCR5380_probe_irq - find the IRQ of a NCR5380 or equivalent
+ * @instance: SCSI host instance
+ *
+ * Autoprobe for the IRQ line used by the card by triggering an IRQ
+ * and then looking to see what interrupt actually turned up.
+ */
+
+static int g_NCR5380_probe_irq(struct Scsi_Host *instance)
+{
+	struct NCR5380_hostdata *hostdata = shost_priv(instance);
+	int irq_mask, irq;
+
+	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+	irq_mask = probe_irq_on();
+	g_NCR5380_trigger_irq(instance);
+	irq = probe_irq_off(irq_mask);
+	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+
+	if (irq <= 0)
+		return NO_IRQ;
+	return irq;
+}
+
 /*
  * Configure I/O address of 53C400A or DTC436 by writing magic numbers
  * to ports 0x779 and 0x379.
@@ -81,14 +131,33 @@ static void magic_configure(int idx, u8 irq, u8 magic[])
 	outb(magic[3], 0x379);
 	outb(magic[4], 0x379);
 
-	/* allowed IRQs for HP C2502 */
-	if (irq != 2 && irq != 3 && irq != 4 && irq != 5 && irq != 7)
-		irq = 0;
+	if (irq == 9)
+		irq = 2;
+
 	if (idx >= 0 && idx <= 7)
 		cfg = 0x80 | idx | (irq << 4);
 	outb(cfg, 0x379);
 }
 
+static irqreturn_t legacy_empty_irq_handler(int irq, void *dev_id)
+{
+	return IRQ_HANDLED;
+}
+
+static int legacy_find_free_irq(int *irq_table)
+{
+	while (*irq_table != -1) {
+		if (!request_irq(*irq_table, legacy_empty_irq_handler,
+		                 IRQF_PROBE_SHARED, "Test IRQ",
+		                 (void *)irq_table)) {
+			free_irq(*irq_table, (void *) irq_table);
+			return *irq_table;
+		}
+		irq_table++;
+	}
+	return -1;
+}
+
 static unsigned int ncr_53c400a_ports[] = {
 	0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350, 0
 };
@@ -101,6 +170,9 @@ static u8 ncr_53c400a_magic[] = {	/* 53C400A & DTC436 */
 static u8 hp_c2502_magic[] = {	/* HP C2502 */
 	0x0f, 0x22, 0xf0, 0x20, 0x80
 };
+static int hp_c2502_irqs[] = {
+	9, 5, 7, 3, 4, -1
+};
 
 static int generic_NCR5380_init_one(struct scsi_host_template *tpnt,
 			struct device *pdev, int base, int irq, int board)
@@ -248,6 +320,13 @@ static int generic_NCR5380_init_one(struct scsi_host_template *tpnt,
 		}
 	}
 
+	/* Check for vacant slot */
+	NCR5380_write(MODE_REG, 0);
+	if (NCR5380_read(MODE_REG) != 0) {
+		ret = -ENODEV;
+		goto out_unregister;
+	}
+
 	ret = NCR5380_init(instance, flags | FLAG_LATE_DMA_SETUP);
 	if (ret)
 		goto out_unregister;
@@ -262,31 +341,59 @@ static int generic_NCR5380_init_one(struct scsi_host_template *tpnt,
 
 	NCR5380_maybe_reset_bus(instance);
 
-	if (irq != IRQ_AUTO)
-		instance->irq = irq;
-	else
-		instance->irq = NCR5380_probe_irq(instance, 0xffff);
-
 	/* Compatibility with documented NCR5380 kernel parameters */
-	if (instance->irq == 255)
-		instance->irq = NO_IRQ;
+	if (irq == 255 || irq == 0)
+		irq = NO_IRQ;
+	else if (irq == -1)
+		irq = IRQ_AUTO;
+
+	if (board == BOARD_HP_C2502) {
+		int *irq_table = hp_c2502_irqs;
+		int board_irq = -1;
+
+		switch (irq) {
+		case NO_IRQ:
+			board_irq = 0;
+			break;
+		case IRQ_AUTO:
+			board_irq = legacy_find_free_irq(irq_table);
+			break;
+		default:
+			while (*irq_table != -1)
+				if (*irq_table++ == irq)
+					board_irq = irq;
+		}
+
+		if (board_irq <= 0) {
+			board_irq = 0;
+			irq = NO_IRQ;
+		}
+
+		magic_configure(port_idx, board_irq, magic);
+	}
+
+	if (irq == IRQ_AUTO) {
+		instance->irq = g_NCR5380_probe_irq(instance);
+		if (instance->irq == NO_IRQ)
+			shost_printk(KERN_INFO, instance, "no irq detected\n");
+	} else {
+		instance->irq = irq;
+		if (instance->irq == NO_IRQ)
+			shost_printk(KERN_INFO, instance, "no irq provided\n");
+	}
 
 	if (instance->irq != NO_IRQ) {
-		/* set IRQ for HP C2502 */
-		if (board == BOARD_HP_C2502)
-			magic_configure(port_idx, instance->irq, magic);
 		if (request_irq(instance->irq, generic_NCR5380_intr,
 				0, "NCR5380", instance)) {
-			printk(KERN_WARNING "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
 			instance->irq = NO_IRQ;
+			shost_printk(KERN_INFO, instance,
+			             "irq %d denied\n", instance->irq);
+		} else {
+			shost_printk(KERN_INFO, instance,
+			             "irq %d acquired\n", instance->irq);
 		}
 	}
 
-	if (instance->irq == NO_IRQ) {
-		printk(KERN_INFO "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
-		printk(KERN_INFO "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
-	}
-
 	ret = scsi_add_host(instance, pdev);
 	if (ret)
 		goto out_free_irq;
@@ -597,7 +704,7 @@ static int __init generic_NCR5380_init(void)
 	int ret = 0;
 
 	/* compatibility with old-style parameters */
-	if (irq[0] == 0 && base[0] == 0 && card[0] == -1) {
+	if (irq[0] == -1 && base[0] == 0 && card[0] == -1) {
 		irq[0] = ncr_irq;
 		base[0] = ncr_addr;
 		if (ncr_5380)

drivers/scsi/g_NCR5380.h

@@ -51,4 +51,6 @@
 #define BOARD_DTC3181E	3
 #define BOARD_HP_C2502	4
 
+#define IRQ_AUTO	254
+
 #endif /* GENERIC_NCR5380_H */

drivers/scsi/ibmvscsi/ibmvscsi.c

@@ -95,6 +95,7 @@ static int fast_fail = 1;
 static int client_reserve = 1;
 static char partition_name[97] = "UNKNOWN";
 static unsigned int partition_number = -1;
+static LIST_HEAD(ibmvscsi_head);
 
 static struct scsi_transport_template *ibmvscsi_transport_template;
 
@@ -232,6 +233,7 @@ static void ibmvscsi_task(void *data)
 		while ((crq = crq_queue_next_crq(&hostdata->queue)) != NULL) {
 			ibmvscsi_handle_crq(crq, hostdata);
 			crq->valid = VIOSRP_CRQ_FREE;
+			wmb();
 		}
 
 		vio_enable_interrupts(vdev);
@@ -240,6 +242,7 @@ static void ibmvscsi_task(void *data)
 			vio_disable_interrupts(vdev);
 			ibmvscsi_handle_crq(crq, hostdata);
 			crq->valid = VIOSRP_CRQ_FREE;
+			wmb();
 		} else {
 			done = 1;
 		}
@@ -992,7 +995,7 @@ static void handle_cmd_rsp(struct srp_event_struct *evt_struct)
 	if (unlikely(rsp->opcode != SRP_RSP)) {
 		if (printk_ratelimit())
 			dev_warn(evt_struct->hostdata->dev,
-				 "bad SRP RSP type %d\n", rsp->opcode);
+				 "bad SRP RSP type %#02x\n", rsp->opcode);
 	}
 	
 	if (cmnd) {
@@ -2270,6 +2273,7 @@ static int ibmvscsi_probe(struct vio_dev *vdev, const struct vio_device_id *id)
 	}
 
 	dev_set_drvdata(&vdev->dev, hostdata);
+	list_add_tail(&hostdata->host_list, &ibmvscsi_head);
 	return 0;
 
       add_srp_port_failed:
@@ -2291,6 +2295,7 @@ static int ibmvscsi_probe(struct vio_dev *vdev, const struct vio_device_id *id)
 static int ibmvscsi_remove(struct vio_dev *vdev)
 {
 	struct ibmvscsi_host_data *hostdata = dev_get_drvdata(&vdev->dev);
+	list_del(&hostdata->host_list);
 	unmap_persist_bufs(hostdata);
 	release_event_pool(&hostdata->pool, hostdata);
 	ibmvscsi_release_crq_queue(&hostdata->queue, hostdata,

drivers/scsi/ibmvscsi/ibmvscsi.h

@@ -90,6 +90,7 @@ struct event_pool {
 
 /* all driver data associated with a host adapter */
 struct ibmvscsi_host_data {
+	struct list_head host_list;
 	atomic_t request_limit;
 	int client_migrated;
 	int reset_crq;

drivers/scsi/ufs/ufs-qcom.c

@@ -23,6 +23,7 @@
 #include "unipro.h"
 #include "ufs-qcom.h"
 #include "ufshci.h"
+#include "ufs_quirks.h"
 #define UFS_QCOM_DEFAULT_DBG_PRINT_EN	\
 	(UFS_QCOM_DBG_PRINT_REGS_EN | UFS_QCOM_DBG_PRINT_TEST_BUS_EN)
 
@@ -1031,6 +1032,34 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 	return ret;
 }
 
+static int ufs_qcom_quirk_host_pa_saveconfigtime(struct ufs_hba *hba)
+{
+	int err;
+	u32 pa_vs_config_reg1;
+
+	err = ufshcd_dme_get(hba, UIC_ARG_MIB(PA_VS_CONFIG_REG1),
+			     &pa_vs_config_reg1);
+	if (err)
+		goto out;
+
+	/* Allow extension of MSB bits of PA_SaveConfigTime attribute */
+	err = ufshcd_dme_set(hba, UIC_ARG_MIB(PA_VS_CONFIG_REG1),
+			    (pa_vs_config_reg1 | (1 << 12)));
+
+out:
+	return err;
+}
+
+static int ufs_qcom_apply_dev_quirks(struct ufs_hba *hba)
+{
+	int err = 0;
+
+	if (hba->dev_quirks & UFS_DEVICE_QUIRK_HOST_PA_SAVECONFIGTIME)
+		err = ufs_qcom_quirk_host_pa_saveconfigtime(hba);
+
+	return err;
+}
+
 static u32 ufs_qcom_get_ufs_hci_version(struct ufs_hba *hba)
 {
 	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
@@ -1194,7 +1223,16 @@ static int ufs_qcom_init(struct ufs_hba *hba)
 	 */
 	host->generic_phy = devm_phy_get(dev, "ufsphy");
 
-	if (IS_ERR(host->generic_phy)) {
+	if (host->generic_phy == ERR_PTR(-EPROBE_DEFER)) {
+		/*
+		 * UFS driver might be probed before the phy driver does.
+		 * In that case we would like to return EPROBE_DEFER code.
+		 */
+		err = -EPROBE_DEFER;
+		dev_warn(dev, "%s: required phy device. hasn't probed yet. err = %d\n",
+			__func__, err);
+		goto out_variant_clear;
+	} else if (IS_ERR(host->generic_phy)) {
 		err = PTR_ERR(host->generic_phy);
 		dev_err(dev, "%s: PHY get failed %d\n", __func__, err);
 		goto out_variant_clear;
@@ -1432,7 +1470,8 @@ static void ufs_qcom_print_hw_debug_reg_all(struct ufs_hba *hba,
 	reg = ufs_qcom_get_debug_reg_offset(host, UFS_UFS_DBG_RD_PRDT_RAM);
 	print_fn(hba, reg, 64, "UFS_UFS_DBG_RD_PRDT_RAM ", priv);
 
-	ufshcd_writel(hba, (reg & ~UFS_BIT(17)), REG_UFS_CFG1);
+	/* clear bit 17 - UTP_DBG_RAMS_EN */
+	ufshcd_rmwl(hba, UFS_BIT(17), 0, REG_UFS_CFG1);
 
 	reg = ufs_qcom_get_debug_reg_offset(host, UFS_DBG_RD_REG_UAWM);
 	print_fn(hba, reg, 4, "UFS_DBG_RD_REG_UAWM ", priv);
@@ -1609,6 +1648,7 @@ static struct ufs_hba_variant_ops ufs_hba_qcom_vops = {
 	.hce_enable_notify      = ufs_qcom_hce_enable_notify,
 	.link_startup_notify    = ufs_qcom_link_startup_notify,
 	.pwr_change_notify	= ufs_qcom_pwr_change_notify,
+	.apply_dev_quirks	= ufs_qcom_apply_dev_quirks,
 	.suspend		= ufs_qcom_suspend,
 	.resume			= ufs_qcom_resume,
 	.dbg_register_dump	= ufs_qcom_dump_dbg_regs,

drivers/scsi/ufs/ufs-qcom.h

@@ -142,6 +142,7 @@ enum ufs_qcom_phy_init_type {
 	 UFS_QCOM_DBG_PRINT_TEST_BUS_EN)
 
 /* QUniPro Vendor specific attributes */
+#define PA_VS_CONFIG_REG1	0x9000
 #define DME_VS_CORE_CLK_CTRL	0xD002
 /* bit and mask definitions for DME_VS_CORE_CLK_CTRL attribute */
 #define DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT		BIT(8)

drivers/scsi/ufs/ufs_quirks.h

@@ -134,29 +134,17 @@ struct ufs_dev_fix {
  */
 #define UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE	(1 << 7)
 
+/*
+ * The max. value PA_SaveConfigTime is 250 (10us) but this is not enough for
+ * some vendors.
+ * Gear switch from PWM to HS may fail even with this max. PA_SaveConfigTime.
+ * Gear switch can be issued by host controller as an error recovery and any
+ * software delay will not help on this case so we need to increase
+ * PA_SaveConfigTime to >32us as per vendor recommendation.
+ */
+#define UFS_DEVICE_QUIRK_HOST_PA_SAVECONFIGTIME	(1 << 8)
 
 struct ufs_hba;
 void ufs_advertise_fixup_device(struct ufs_hba *hba);
 
-static struct ufs_dev_fix ufs_fixups[] = {
-	/* UFS cards deviations table */
-	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
-		UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM),
-	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL, UFS_DEVICE_NO_VCCQ),
-	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
-		UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS),
-	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
-		UFS_DEVICE_NO_FASTAUTO),
-	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
-		UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE),
-	UFS_FIX(UFS_VENDOR_TOSHIBA, UFS_ANY_MODEL,
-		UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM),
-	UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9C8KBADG",
-		UFS_DEVICE_QUIRK_PA_TACTIVATE),
-	UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9D8KBADG",
-		UFS_DEVICE_QUIRK_PA_TACTIVATE),
-	UFS_FIX(UFS_VENDOR_SKHYNIX, UFS_ANY_MODEL, UFS_DEVICE_NO_VCCQ),
-
-	END_FIX
-};
 #endif /* UFS_QUIRKS_H_ */

drivers/scsi/ufs/ufshcd.c

@@ -185,6 +185,30 @@ ufs_get_pm_lvl_to_link_pwr_state(enum ufs_pm_level lvl)
 	return ufs_pm_lvl_states[lvl].link_state;
 }
 
+static struct ufs_dev_fix ufs_fixups[] = {
+	/* UFS cards deviations table */
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
+		UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM),
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL, UFS_DEVICE_NO_VCCQ),
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
+		UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS),
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
+		UFS_DEVICE_NO_FASTAUTO),
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
+		UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE),
+	UFS_FIX(UFS_VENDOR_TOSHIBA, UFS_ANY_MODEL,
+		UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM),
+	UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9C8KBADG",
+		UFS_DEVICE_QUIRK_PA_TACTIVATE),
+	UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9D8KBADG",
+		UFS_DEVICE_QUIRK_PA_TACTIVATE),
+	UFS_FIX(UFS_VENDOR_SKHYNIX, UFS_ANY_MODEL, UFS_DEVICE_NO_VCCQ),
+	UFS_FIX(UFS_VENDOR_SKHYNIX, UFS_ANY_MODEL,
+		UFS_DEVICE_QUIRK_HOST_PA_SAVECONFIGTIME),
+
+	END_FIX
+};
+
 static void ufshcd_tmc_handler(struct ufs_hba *hba);
 static void ufshcd_async_scan(void *data, async_cookie_t cookie);
 static int ufshcd_reset_and_restore(struct ufs_hba *hba);
@@ -288,10 +312,24 @@ int ufshcd_wait_for_register(struct ufs_hba *hba, u32 reg, u32 mask,
  */
 static inline u32 ufshcd_get_intr_mask(struct ufs_hba *hba)
 {
-	if (hba->ufs_version == UFSHCI_VERSION_10)
-		return INTERRUPT_MASK_ALL_VER_10;
-	else
-		return INTERRUPT_MASK_ALL_VER_11;
+	u32 intr_mask = 0;
+
+	switch (hba->ufs_version) {
+	case UFSHCI_VERSION_10:
+		intr_mask = INTERRUPT_MASK_ALL_VER_10;
+		break;
+	/* allow fall through */
+	case UFSHCI_VERSION_11:
+	case UFSHCI_VERSION_20:
+		intr_mask = INTERRUPT_MASK_ALL_VER_11;
+		break;
+	/* allow fall through */
+	case UFSHCI_VERSION_21:
+	default:
+		intr_mask = INTERRUPT_MASK_ALL_VER_21;
+	}
+
+	return intr_mask;
 }
 
 /**
@@ -5199,6 +5237,8 @@ static void ufshcd_tune_unipro_params(struct ufs_hba *hba)
 
 	if (hba->dev_quirks & UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE)
 		ufshcd_quirk_tune_host_pa_tactivate(hba);
+
+	ufshcd_vops_apply_dev_quirks(hba);
 }
 
 /**
@@ -6667,6 +6707,13 @@ int ufshcd_init(struct ufs_hba *hba, void __iomem *mmio_base, unsigned int irq)
 	/* Get UFS version supported by the controller */
 	hba->ufs_version = ufshcd_get_ufs_version(hba);
 
+	if ((hba->ufs_version != UFSHCI_VERSION_10) &&
+	    (hba->ufs_version != UFSHCI_VERSION_11) &&
+	    (hba->ufs_version != UFSHCI_VERSION_20) &&
+	    (hba->ufs_version != UFSHCI_VERSION_21))
+		dev_err(hba->dev, "invalid UFS version 0x%x\n",
+			hba->ufs_version);
+
 	/* Get Interrupt bit mask per version */
 	hba->intr_mask = ufshcd_get_intr_mask(hba);
 

drivers/scsi/ufs/ufshcd.h

@@ -266,7 +266,7 @@ struct ufs_pwr_mode_info {
  * @setup_task_mgmt: called before any task management request is issued
  *                  to set some things
  * @hibern8_notify: called around hibern8 enter/exit
- *		    to configure some things
+ * @apply_dev_quirks: called to apply device specific quirks
  * @suspend: called during host controller PM callback
  * @resume: called during host controller PM callback
  * @dbg_register_dump: used to dump controller debug information
@@ -294,6 +294,7 @@ struct ufs_hba_variant_ops {
 	void	(*setup_task_mgmt)(struct ufs_hba *, int, u8);
 	void    (*hibern8_notify)(struct ufs_hba *, enum uic_cmd_dme,
 					enum ufs_notify_change_status);
+	int	(*apply_dev_quirks)(struct ufs_hba *);
 	int     (*suspend)(struct ufs_hba *, enum ufs_pm_op);
 	int     (*resume)(struct ufs_hba *, enum ufs_pm_op);
 	void	(*dbg_register_dump)(struct ufs_hba *hba);
@@ -839,6 +840,13 @@ static inline void ufshcd_vops_hibern8_notify(struct ufs_hba *hba,
 		return hba->vops->hibern8_notify(hba, cmd, status);
 }
 
+static inline int ufshcd_vops_apply_dev_quirks(struct ufs_hba *hba)
+{
+	if (hba->vops && hba->vops->apply_dev_quirks)
+		return hba->vops->apply_dev_quirks(hba);
+	return 0;
+}
+
 static inline int ufshcd_vops_suspend(struct ufs_hba *hba, enum ufs_pm_op op)
 {
 	if (hba->vops && hba->vops->suspend)

drivers/scsi/ufs/ufshci.h

@@ -72,6 +72,10 @@ enum {
 	REG_UIC_COMMAND_ARG_1			= 0x94,
 	REG_UIC_COMMAND_ARG_2			= 0x98,
 	REG_UIC_COMMAND_ARG_3			= 0x9C,
+	REG_UFS_CCAP				= 0x100,
+	REG_UFS_CRYPTOCAP			= 0x104,
+
+	UFSHCI_CRYPTO_REG_SPACE_SIZE		= 0x400,
 };
 
 /* Controller capability masks */
@@ -275,6 +279,9 @@ enum {
 
 	/* Interrupt disable mask for UFSHCI v1.1 */
 	INTERRUPT_MASK_ALL_VER_11	= 0x31FFF,
+
+	/* Interrupt disable mask for UFSHCI v2.1 */
+	INTERRUPT_MASK_ALL_VER_21	= 0x71FFF,
 };
 
 /*