Skip to content

L
linux
Commit 42d61413 authored by Arnd Bergmann's avatar Arnd Bergmann
Browse files
Options

Merge tag 'imx-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt 

i.MX device tree changes for 5.1:
 - New board support: Logic PD i.MX6QD EVM, ZII SSMB DTU, Phytec
   phyBOARD i.MX6UL Segin, Y Soft IOTA Draco, Hydra and Ursa boards.
 - Add regulator control for various sensors on imx6qdl-sabresd board.
 - Add DISPLAY power domain support for i.MX6SX SoC.
 - Add stmpe-adc device node for Toradex iMX6 module.
 - Switch to SPDX identifier for imx6q-tbs2910 board.
 - Add proper ksz9031 clock skew values for imx6qdl-phytec-pfla02 board.
 - Mark I2C recovery GPIOs as open drain and correct and WEIM range
   configuration for apalis/colibri boards.
 - Small and random updates to various devices.

* tag 'imx-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (31 commits)
  ARM: dts: imx: Add support for Logic PD i.MX6QD EVM
  ARM: dts: imx6qdl-sabresd: remove reg_sensors' regulator-always-on
  ARM: dts: imx6qdl-sabresd: add regulators control for mma8451 sensor
  ARM: dts: imx6qdl-sabresd: add regulators control for mag3110 sensor
  ARM: dts: imx6qdl-sabresd: add regulator control for isl29023 sensor
  ARM: dts: vf610: Add ZII SSMB DTU board
  ARM: dts: pfla02: add ksz9031 clock skew values
  ARM: dts: imx6qdl-phytec-pfla02: add missing interrupt-controller property
  ARM: dts: Add stmpe-adc DT node to Toradex iMX6 modules
  ARM: dts: Add devicetree compatibles for LS1021A based boards
  ARM: dts: colibri: use valid range configuration for weim
  ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin
  ARM: dts: imx6*-apalis/-colibri: mark I2C recovery GPIOs as open drain
  ARM: dts: vf610-zii-ssmb-spu3: Pass "no-sdio"/"no-sd" properties
  ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards
  ARM: dts: imx7ulp: add sim node
  ARM: dts: imx6ull: change to use new compatible "fsl,imx6ull-usdhc" for usdhc
  ARM: dts: imx6ull: Fix i.MX6ULL/ULZ ocotp compatible
  ARM: dts: imx6sx: Add DISPLAY power domain support
  ARM: dts: i.MX51: digi-connectcore-som: Add support for I2C bus recovery
  ...
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
parents 89081095 1c207f91
Hide whitespace changes
Inline Side-by-side
Showing with 2938 additions and 89 deletions
arch/arm/boot/dts/Makefile
View file @ 42d61413
...@@ -448,6 +448,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ ...@@ -448,6 +448,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-wandboard.dtb \ imx6dl-wandboard.dtb \
imx6dl-wandboard-revb1.dtb \ imx6dl-wandboard-revb1.dtb \
imx6dl-wandboard-revd1.dtb \ imx6dl-wandboard-revd1.dtb \
imx6dl-yapp4-draco.dtb \
imx6dl-yapp4-hydra.dtb \
imx6dl-yapp4-ursa.dtb \
imx6q-apalis-eval.dtb \ imx6q-apalis-eval.dtb \
imx6q-apalis-ixora.dtb \ imx6q-apalis-ixora.dtb \
imx6q-apalis-ixora-v1.1.dtb \ imx6q-apalis-ixora-v1.1.dtb \
...@@ -564,6 +567,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ ...@@ -564,6 +567,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-opos6uldev.dtb \ imx6ul-opos6uldev.dtb \
imx6ul-pico-hobbit.dtb \ imx6ul-pico-hobbit.dtb \
imx6ul-pico-pi.dtb \ imx6ul-pico-pi.dtb \
imx6ul-phytec-phyboard-segin-full.dtb \
imx6ul-tx6ul-0010.dtb \ imx6ul-tx6ul-0010.dtb \
imx6ul-tx6ul-0011.dtb \ imx6ul-tx6ul-0011.dtb \
imx6ul-tx6ul-mainboard.dtb \ imx6ul-tx6ul-mainboard.dtb \
...@@ -602,6 +606,7 @@ dtb-$(CONFIG_SOC_VF610) += \ ...@@ -602,6 +606,7 @@ dtb-$(CONFIG_SOC_VF610) += \
vf610-zii-dev-rev-b.dtb \ vf610-zii-dev-rev-b.dtb \
vf610-zii-dev-rev-c.dtb \ vf610-zii-dev-rev-c.dtb \
vf610-zii-scu4-aib.dtb \ vf610-zii-scu4-aib.dtb \
vf610-zii-ssmb-dtu.dtb \
vf610-zii-ssmb-spu3.dtb vf610-zii-ssmb-spu3.dtb
dtb-$(CONFIG_ARCH_MXS) += \ dtb-$(CONFIG_ARCH_MXS) += \
imx23-evk.dtb \ imx23-evk.dtb \
......
arch/arm/boot/dts/imx27.dtsi
View file @ 42d61413
...@@ -40,7 +40,7 @@ aliases { ...@@ -40,7 +40,7 @@ aliases {
spi2 = &cspi3; spi2 = &cspi3;
}; };
aitc: aitc-interrupt-controller@e0000000 { aitc: aitc-interrupt-controller@10040000 {
compatible = "fsl,imx27-aitc", "fsl,avic"; compatible = "fsl,imx27-aitc", "fsl,avic";
interrupt-controller; interrupt-controller;
#interrupt-cells = <1>; #interrupt-cells = <1>;
......
arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts
View file @ 42d61413
...@@ -21,12 +21,28 @@ chosen { ...@@ -21,12 +21,28 @@ chosen {
}; };
}; };
&esdhc1 {
status = "okay";
};
&owire { &owire {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&pinctrl_owire>; pinctrl-0 = <&pinctrl_owire>;
status = "okay"; status = "okay";
}; };
&pmic {
fsl,mc13xxx-uses-rtc;
regulators {
vcoincell_reg: vcoincell {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
};
};
};
&uart1 { &uart1 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>; pinctrl-0 = <&pinctrl_uart1>;
......
arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi
View file @ 42d61413
...@@ -37,7 +37,6 @@ pmic: mc13892@0 { ...@@ -37,7 +37,6 @@ pmic: mc13892@0 {
reg = <0>; reg = <0>;
interrupt-parent = <&gpio1>; interrupt-parent = <&gpio1>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
fsl,mc13xxx-uses-rtc;
regulators { regulators {
sw1_reg: sw1 { sw1_reg: sw1 {
...@@ -142,16 +141,17 @@ vusb_reg: vusb { ...@@ -142,16 +141,17 @@ vusb_reg: vusb {
pwgt2spi_reg: pwgt2spi { pwgt2spi_reg: pwgt2spi {
regulator-always-on; regulator-always-on;
}; };
vcoincell_reg: vcoincell {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
};
}; };
}; };
}; };
&esdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc1>;
max-frequency = <50000000>;
bus-width = <1>;
};
&esdhc2 { &esdhc2 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc2>; pinctrl-0 = <&pinctrl_esdhc2>;
...@@ -174,9 +174,12 @@ &fec { ...@@ -174,9 +174,12 @@ &fec {
}; };
&i2c2 { &i2c2 {
pinctrl-names = "default"; pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>; pinctrl-0 = <&pinctrl_i2c2>;
pinctrl-1 = <&pinctrl_i2c2_gpio>;
clock-frequency = <400000>; clock-frequency = <400000>;
scl-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
status = "okay"; status = "okay";
mma7455l@1d { mma7455l@1d {
...@@ -241,6 +244,14 @@ MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 /* CS0 */ ...@@ -241,6 +244,14 @@ MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 /* CS0 */
>; >;
}; };
pinctrl_esdhc1: esdhc1grp {
fsl,pins = <
MX51_PAD_SD1_CLK__SD1_CLK 0x400021d5
MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5
MX51_PAD_SD1_DATA0__SD1_DATA0 0x400020d5
>;
};
pinctrl_esdhc2: esdhc2grp { pinctrl_esdhc2: esdhc2grp {
fsl,pins = < fsl,pins = <
MX51_PAD_SD2_CMD__SD2_CMD 0x400020d5 MX51_PAD_SD2_CMD__SD2_CMD 0x400020d5
...@@ -282,6 +293,13 @@ MX51_PAD_GPIO1_3__I2C2_SDA 0x400001ed ...@@ -282,6 +293,13 @@ MX51_PAD_GPIO1_3__I2C2_SDA 0x400001ed
>; >;
}; };
pinctrl_i2c2_gpio: i2c2gpiogrp {
fsl,pins = <
MX51_PAD_GPIO1_2__GPIO1_2 0x400001ed
MX51_PAD_GPIO1_3__GPIO1_3 0x400001ed
>;
};
pinctrl_nfc: nfcgrp { pinctrl_nfc: nfcgrp {
fsl,pins = < fsl,pins = <
MX51_PAD_NANDF_D0__NANDF_D0 0x80000000 MX51_PAD_NANDF_D0__NANDF_D0 0x80000000
......
arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
//
// Copyright (C) 2019 Logic PD, Inc.
/ {
keyboard {
compatible = "gpio-keys";
btn0 {
gpios = <&pcf8575 0 GPIO_ACTIVE_LOW>;
label = "btn0";
linux,code = <KEY_WAKEUP>;
debounce-interval = <10>;
wakeup-source;
};
btn1 {
gpios = <&pcf8575 1 GPIO_ACTIVE_LOW>;
label = "btn1";
linux,code = <KEY_WAKEUP>;
debounce-interval = <10>;
wakeup-source;
};
btn2 {
gpios = <&pcf8575 2 GPIO_ACTIVE_LOW>;
label = "btn2";
linux,code = <KEY_WAKEUP>;
debounce-interval = <10>;
wakeup-source;
};
btn3 {
gpios = <&pcf8575 3 GPIO_ACTIVE_LOW>;
label = "btn3";
linux,code = <KEY_WAKEUP>;
debounce-interval = <10>;
wakeup-source;
};
};
leds {
compatible = "gpio-leds";
gen-led0 {
label = "led0";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_led0>;
gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "cpu0";
};
gen-led1 {
label = "led1";
gpios = <&pcf8575 8 GPIO_ACTIVE_HIGH>;
};
gen-led2 {
label = "led2";
gpios = <&pcf8575 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
gen-led3 {
label = "led3";
gpios = <&pcf8575 10 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
};
reg_usb_otg_vbus: regulator-otg-vbus {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_usb_otg>;
compatible = "regulator-fixed";
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_usb_h1_vbus: regulator-usb-h1-vbus {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_usb_h1_vbus>;
compatible = "regulator-fixed";
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_3v3: regulator-3v3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_3v3>;
compatible = "regulator-fixed";
regulator-name = "reg_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
};
reg_enet: regulator-ethernet {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_enet>;
compatible = "regulator-fixed";
regulator-name = "ethernet-supply";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
startup-delay-us = <70000>;
enable-active-high;
vin-supply = <&sw4_reg>;
};
reg_audio: regulator-audio {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_audio>;
compatible = "regulator-fixed";
regulator-name = "3v3_aud";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
enable-active-high;
vin-supply = <&reg_3v3>;
};
reg_hdmi: regulator-hdmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_hdmi>;
compatible = "regulator-fixed";
regulator-name = "hdmi-supply";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
enable-active-high;
vin-supply = <&reg_3v3>;
};
reg_uart3: regulator-uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_uart3>;
compatible = "regulator-fixed";
regulator-name = "uart3-supply";
gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
vin-supply = <&reg_3v3>;
};
reg_1v8: regulator-1v8 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_1v8>;
compatible = "regulator-fixed";
regulator-name = "1v8-supply";
gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
vin-supply = <&reg_3v3>;
};
reg_pcie: regulator-pcie {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_pcie>;
regulator-name = "mpcie_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_mipi: regulator-mipi {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_mipi>;
regulator-name = "mipi_pwr_en";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
sound {
compatible = "fsl,imx-audio-wm8962";
model = "wm8962-audio";
ssi-controller = <&ssi2>;
audio-codec = <&wm8962>;
audio-routing =
"Headphone Jack", "HPOUTL",
"Headphone Jack", "HPOUTR",
"Ext Spk", "SPKOUTL",
"Ext Spk", "SPKOUTR",
"AMIC", "MICBIAS",
"IN3R", "AMIC";
mux-int-port = <2>;
mux-ext-port = <4>;
};
};
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
status = "okay";
};
&ecspi1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "disabled";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
phy-reset-duration = <10>;
phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
phy-supply = <&reg_enet>;
interrupt-parent = <&gpio1>;
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
clock-frequency = <400000>;
status = "okay";
wm8962: audio-codec@1a {
compatible = "wlf,wm8962";
reg = <0x1a>;
clocks = <&clks IMX6QDL_CLK_CKO>;
clock-names = "xclk";
DCVDD-supply = <&reg_audio>;
DBVDD-supply = <&reg_audio>;
AVDD-supply = <&reg_audio>;
CPVDD-supply = <&reg_audio>;
MICVDD-supply = <&reg_audio>;
PLLVDD-supply = <&reg_audio>;
SPKVDD1-supply = <&reg_audio>;
SPKVDD2-supply = <&reg_audio>;
gpio-cfg = <
0x0000 /* 0:Default */
0x0000 /* 1:Default */
0x0013 /* 2:FN_DMICCLK */
0x0000 /* 3:Default */
0x8014 /* 4:FN_DMICCDAT */
0x0000 /* 5:Default */
>;
};
};
&i2c3 {
ov5640: camera@10 {
compatible = "ovti,ov5640";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ov5640>;
reg = <0x10>;
clocks = <&clks IMX6QDL_CLK_CKO>;
clock-names = "xclk";
DOVDD-supply = <&reg_mipi>;
AVDD-supply = <&reg_mipi>;
DVDD-supply = <&reg_mipi>;
reset-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
powerdown-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
port {
ov5640_to_mipi_csi2: endpoint {
remote-endpoint = <&mipi_csi2_in>;
clock-lanes = <0>;
data-lanes = <1 2>;
};
};
};
pcf8575: gpio@20 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcf8574>;
compatible = "nxp,pcf8575";
reg = <0x20>;
interrupt-parent = <&gpio6>;
interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
lines-initial-states = <0x0710>;
wakeup-source;
};
};
&ipu1_csi1_from_mipi_vc1 {
clock-lanes = <0>;
data-lanes = <1 2>;
};
&mipi_csi {
status = "okay";
port@0 {
reg = <0>;
mipi_csi2_in: endpoint {
remote-endpoint = <&ov5640_to_mipi_csi2>;
clock-lanes = <0>;
data-lanes = <1 2>;
};
};
};
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
vpcie-supply = <&reg_pcie>;
status = "okay";
};
&pwm3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
};
&ssi2 {
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
&usbh1 {
vbus-supply = <&reg_usb_h1_vbus>;
status = "okay";
};
&usbotg {
vbus-supply = <&reg_usb_otg_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
dr_mode = "otg";
status = "okay";
};
&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2>;
pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
vmmc-supply = <&reg_3v3>;
no-1-8-v;
keep-power-in-suspend;
cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
status = "okay";
};
&iomuxc {
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0 0x100b1
>;
};
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b8b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x13030
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x13030
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x13030
MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 /* ENET_INT */
MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x1b0b0 /* ETHR_nRST */
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
>;
};
pinctrl_led0: led0grp {
fsl,pins = <
MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
>;
};
pinctrl_ov5640: ov5640grp {
fsl,pins = <
MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b1
MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x1b0b1
>;
};
pinctrl_pcf8574: pcf8575grp {
fsl,pins = <
MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0
>;
};
pinctrl_pcie: pciegrp {
fsl,pins = <
MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
>;
};
pinctrl_pwm3: pwm3grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
>;
};
pinctrl_reg_1v8: reg1v8grp {
fsl,pins = <
MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b0
>;
};
pinctrl_reg_3v3: reg3v3grp {
fsl,pins = <
MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b0
>;
};
pinctrl_reg_audio: reg-audiogrp {
fsl,pins = <
MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
>;
};
pinctrl_reg_enet: reg-enetgrp {
fsl,pins = <
MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
>;
};
pinctrl_reg_hdmi: reg-hdmigrp {
fsl,pins = <
MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
>;
};
pinctrl_reg_mipi: reg-mipigrp {
fsl,pins = <MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b1>;
};
pinctrl_reg_pcie: reg-pciegrp {
fsl,pins = <
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
>;
};
pinctrl_reg_uart3: reguart3grp {
fsl,pins = <
MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
>;
};
pinctrl_reg_usb_h1_vbus: usbh1grp {
fsl,pins = <
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
>;
};
pinctrl_reg_usb_otg: reg-usb-otggrp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
>;
};
pinctrl_uart3: uart3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0xd17059
>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17069
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10069
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17069
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17069
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17069
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17069
>;
};
pinctrl_usdhc2_100mhz: h100-usdhc2-100mhz {
fsl,pins = <
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
>;
};
pinctrl_usdhc2_200mhz: h100-usdhc2-200mhz {
fsl,pins = <
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9
>;
};
};
arch/arm/boot/dts/imx6-logicpd-som.dtsi 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
//
// Copyright (C) 2019 Logic PD, Inc.
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
chosen {
stdout-path = &uart1;
};
memory@10000000 {
device_type = "memory";
reg = <0x10000000 0x80000000>;
};
reg_wl18xx_vmmc: regulator-wl18xx {
compatible = "regulator-fixed";
regulator-name = "vwl1837";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio7 0 GPIO_ACTIVE_HIGH>;
startup-delay-us = <70000>;
enable-active-high;
};
};
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
<&clks IMX6QDL_CLK_LDB_DI1_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
<&clks IMX6QDL_CLK_PLL3_USB_OTG>;
};
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
nand-on-flash-bbt;
status = "okay";
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
pfuze100: pmic@8 {
compatible = "fsl,pfuze100";
reg = <0x08>;
regulators {
sw1a_reg: sw1ab {
regulator-min-microvolt = <725000>;
regulator-max-microvolt = <1450000>;
regulator-name = "vddcore";
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <6250>;
};
sw1c_reg: sw1c {
regulator-min-microvolt = <725000>;
regulator-max-microvolt = <1450000>;
regulator-name = "vddsoc";
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <6250>;
};
sw2_reg: sw2 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "gen_3v3";
regulator-boot-on;
};
sw3a_reg: sw3a {
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-name = "sw3a_vddr";
regulator-boot-on;
regulator-always-on;
};
sw3b_reg: sw3b {
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-name = "sw3b_vddr";
regulator-boot-on;
regulator-always-on;
};
sw4_reg: sw4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-name = "gen_rgmii";
};
swbst_reg: swbst {
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5150000>;
regulator-name = "gen_5v0";
};
snvs_reg: vsnvs {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "gen_vsns";
regulator-boot-on;
regulator-always-on;
};
vref_reg: vrefddr {
regulator-boot-on;
regulator-always-on;
};
vgen1_reg: vgen1 {
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-name = "gen_1v5";
};
vgen2_reg: vgen2 {
regulator-name = "vgen2";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1550000>;
};
vgen3_reg: vgen3 {
regulator-name = "gen_vadj_0";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
vgen4_reg: vgen4 {
regulator-name = "gen_1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vgen5_reg: vgen5 {
regulator-name = "gen_vadj_1";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vgen6_reg: vgen6 {
regulator-name = "gen_2v5";
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
regulator-always-on;
};
coin_reg: coin {
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
};
};
};
temperature-sensor@49 {
compatible = "ti,tmp102";
reg = <0x49>;
interrupt-parent = <&gpio6>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
#thermal-sensor-cells = <1>;
};
temperature-sensor@4a {
compatible = "ti,tmp102";
reg = <0x4a>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tempsense>;
interrupt-parent = <&gpio6>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
#thermal-sensor-cells = <1>;
};
eeprom@51 {
compatible = "atmel,24c64";
pagesize = <32>;
read-only; /* Manufacturing EEPROM programmed at factory */
reg = <0x51>;
};
eeprom@52 {
compatible = "atmel,24c64";
pagesize = <32>;
reg = <0x52>;
};
};
/* Reroute power feeding the CPU to come from the external PMIC */
&reg_arm
{
vin-supply = <&sw1a_reg>;
};
&reg_soc
{
vin-supply = <&sw1c_reg>;
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
pinctrl_gpmi_nand: gpmi-nandgrp {
fsl,pins = <
MX6QDL_PAD_NANDF_CLE__NAND_CLE 0x0b0b1
MX6QDL_PAD_NANDF_ALE__NAND_ALE 0x0b0b1
MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0x0b0b1
MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0x0b000
MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0x0b0b1
MX6QDL_PAD_SD4_CMD__NAND_RE_B 0x0b0b1
MX6QDL_PAD_SD4_CLK__NAND_WE_B 0x0b0b1
MX6QDL_PAD_NANDF_D0__NAND_DATA00 0x0b0b1
MX6QDL_PAD_NANDF_D1__NAND_DATA01 0x0b0b1
MX6QDL_PAD_NANDF_D2__NAND_DATA02 0x0b0b1
MX6QDL_PAD_NANDF_D3__NAND_DATA03 0x0b0b1
MX6QDL_PAD_NANDF_D4__NAND_DATA04 0x0b0b1
MX6QDL_PAD_NANDF_D5__NAND_DATA05 0x0b0b1
MX6QDL_PAD_NANDF_D6__NAND_DATA06 0x0b0b1
MX6QDL_PAD_NANDF_D7__NAND_DATA07 0x0b0b1
>;
};
pinctrl_hog: hoggrp {
fsl,pins = < /* Enable ARM Debugger */
MX6QDL_PAD_CSI0_MCLK__ARM_TRACE_CTL 0x1b0b0
MX6QDL_PAD_CSI0_PIXCLK__ARM_EVENTO 0x1b0b0
MX6QDL_PAD_CSI0_VSYNC__ARM_TRACE00 0x1b0b0
MX6QDL_PAD_CSI0_DATA_EN__ARM_TRACE_CLK 0x1b0b0
MX6QDL_PAD_CSI0_DAT4__ARM_TRACE01 0x1b0b0
MX6QDL_PAD_CSI0_DAT5__ARM_TRACE02 0x1b0b0
MX6QDL_PAD_CSI0_DAT6__ARM_TRACE03 0x1b0b0
MX6QDL_PAD_CSI0_DAT7__ARM_TRACE04 0x1b0b0
MX6QDL_PAD_CSI0_DAT8__ARM_TRACE05 0x1b0b0
MX6QDL_PAD_CSI0_DAT9__ARM_TRACE06 0x1b0b0
MX6QDL_PAD_CSI0_DAT10__ARM_TRACE07 0x1b0b0
MX6QDL_PAD_CSI0_DAT11__ARM_TRACE08 0x1b0b0
MX6QDL_PAD_CSI0_DAT12__ARM_TRACE09 0x1b0b0
MX6QDL_PAD_CSI0_DAT13__ARM_TRACE10 0x1b0b0
MX6QDL_PAD_CSI0_DAT14__ARM_TRACE11 0x1b0b0
MX6QDL_PAD_CSI0_DAT15__ARM_TRACE12 0x1b0b0
MX6QDL_PAD_CSI0_DAT16__ARM_TRACE13 0x1b0b0
MX6QDL_PAD_CSI0_DAT17__ARM_TRACE14 0x1b0b0
MX6QDL_PAD_CSI0_DAT18__ARM_TRACE15 0x1b0b0
MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_tempsense: tempsensegrp {
fsl,pins = <
MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x13059 /* BT_EN */
MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170B9
MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100B9
MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170B9
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170B9
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170B9
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170B9
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17049
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10049
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17049
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17049
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17049
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17049
MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x130b0 /* WL_IRQ */
MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* WLAN_EN */
>;
};
};
&snvs_poweroff {
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "ti,wl1837-st";
enable-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
};
};
&usdhc1 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>;
non-removable;
keep-power-in-suspend;
wakeup-source;
vmmc-supply = <&sw2_reg>;
status = "okay";
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
non-removable;
cap-power-off-card;
keep-power-in-suspend;
wakeup-source;
vmmc-supply = <&reg_wl18xx_vmmc>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
wlcore: wlcore@2 {
compatible = "ti,wl1837";
reg = <2>;
interrupt-parent = <&gpio7>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
tcxo-clock-frequency = <26000000>;
};
};
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
View file @ 42d61413
...@@ -228,10 +228,11 @@ &usdhc1 { ...@@ -228,10 +228,11 @@ &usdhc1 {
&weim { &weim {
status = "okay"; status = "okay";
/* weim memory map: 32MB on CS0, 32MB on CS1, 32MB on CS2 */ /* weim memory map: 32MB on CS0, CS1, CS2 and CS3 */
ranges = <0 0 0x08000000 0x02000000 ranges = <0 0 0x08000000 0x02000000
1 0 0x0a000000 0x02000000 1 0 0x0a000000 0x02000000
2 0 0x0c000000 0x02000000>; 2 0 0x0c000000 0x02000000
3 0 0x0e000000 0x02000000>;
/* SRAM on Colibri nEXT_CS0 */ /* SRAM on Colibri nEXT_CS0 */
sram@0,0 { sram@0,0 {
......
arch/arm/boot/dts/imx6dl-yapp4-common.dtsi 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
//
// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pwm/pwm.h>
/ {
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 32 64 128 255>;
default-brightness-level = <32>;
num-interpolated-steps = <8>;
power-supply = <&sw2_reg>;
status = "disabled";
};
lcd_display: display {
compatible = "fsl,imx-parallel-display";
#address-cells = <1>;
#size-cells = <0>;
interface-pix-fmt = "rgb24";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ipu1>;
status = "disabled";
port@0 {
reg = <0>;
lcd_display_in: endpoint {
remote-endpoint = <&ipu1_di0_disp0>;
};
};
port@1 {
reg = <1>;
lcd_display_out: endpoint {
remote-endpoint = <&lcd_panel_in>;
};
};
};
panel: panel {
compatible = "dataimage,scf0700c48ggu18";
power-supply = <&sw2_reg>;
status = "disabled";
port {
lcd_panel_in: endpoint {
remote-endpoint = <&lcd_display_out>;
};
};
};
reg_pcie: regulator-pcie {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie_reg>;
regulator-name = "MPCIE_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
status = "disabled";
};
reg_usb_h1_vbus: regulator-usb-h1-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh1_vbus>;
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
enable-active-high;
status = "disabled";
};
reg_usb_otg_vbus: regulator-usb-otg-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg_vbus>;
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
status = "okay";
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
phy-reset-duration = <20>;
phy-supply = <&sw2_reg>;
phy-handle = <&ethphy0>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy_port2: phy@1 {
reg = <1>;
};
phy_port3: phy@2 {
reg = <2>;
};
switch@0 {
compatible = "qca,qca8334";
reg = <0>;
switch_ports: ports {
#address-cells = <1>;
#size-cells = <0>;
ethphy0: port@0 {
reg = <0>;
label = "cpu";
phy-mode = "rgmii";
ethernet = <&fec>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
port@2 {
reg = <2>;
label = "eth2";
phy-handle = <&phy_port2>;
};
port@3 {
reg = <3>;
label = "eth1";
phy-handle = <&phy_port3>;
};
};
};
};
};
&hdmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hdmi_cec>;
ddc-i2c-bus = <&i2c2>;
status = "disabled";
};
&i2c2 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
pmic@8 {
compatible = "fsl,pfuze200";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pmic>;
reg = <0x8>;
regulators {
sw1a_reg: sw1ab {
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <1875000>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <6250>;
};
sw2_reg: sw2 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
sw3a_reg: sw3a {
regulator-min-microvolt = <400000>;
regulator-max-microvolt = <1975000>;
regulator-boot-on;
regulator-always-on;
};
sw3b_reg: sw3b {
regulator-min-microvolt = <400000>;
regulator-max-microvolt = <1975000>;
regulator-boot-on;
regulator-always-on;
};
swbst_reg: swbst {
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5150000>;
};
vgen1_reg: vgen1 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1550000>;
};
vgen2_reg: vgen2 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1550000>;
};
vgen3_reg: vgen3 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vgen4_reg: vgen4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vgen5_reg: vgen5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vgen6_reg: vgen6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vref_reg: vrefddr {
regulator-boot-on;
regulator-always-on;
};
vsnvs_reg: vsnvs {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <3000000>;
regulator-boot-on;
regulator-always-on;
};
};
};
leds: led-controller@30 {
compatible = "ti,lp5562";
reg = <0x30>;
clock-mode = /bits/ 8 <1>;
status = "disabled";
chan0 {
chan-name = "R";
led-cur = /bits/ 8 <0x20>;
max-cur = /bits/ 8 <0x60>;
};
chan1 {
chan-name = "G";
led-cur = /bits/ 8 <0x20>;
max-cur = /bits/ 8 <0x60>;
};
chan2 {
chan-name = "B";
led-cur = /bits/ 8 <0x20>;
max-cur = /bits/ 8 <0x60>;
};
chan3 {
chan-name = "W";
led-cur = /bits/ 8 <0x0>;
max-cur = /bits/ 8 <0x0>;
};
};
eeprom@57 {
compatible = "atmel,24c128";
reg = <0x57>;
pagesize = <64>;
status = "okay";
};
touchscreen: touchscreen@5c {
compatible = "pixcir,pixcir_tangoc";
reg = <0x5c>;
pinctrl-0 = <&pinctrl_touch>;
interrupt-parent = <&gpio4>;
interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
status = "disabled";
};
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "disabled";
oled: oled@3d {
compatible = "solomon,ssd1305fb-i2c";
reg = <0x3d>;
solomon,height = <64>;
solomon,width = <128>;
solomon,page-offset = <0>;
solomon,prechargep2 = <15>;
reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
vbat-supply = <&sw2_reg>;
status = "disabled";
};
gpio_oled: gpio@41 {
compatible = "nxp,pca9536";
gpio-controller;
#gpio-cells = <2>;
reg = <0x41>;
vcc-supply = <&sw2_reg>;
status = "disabled";
};
};
&iomuxc {
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b020
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b020
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020
MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b020
MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b020
MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b020
MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b020
MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b020
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b020
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b020
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b020
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b020
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b020
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b020
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b010
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b010
MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b098
>;
};
pinctrl_hdmi_cec: hdmicecgrp {
fsl,pins = <
MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1b898
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b899
MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b899
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b899
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
>;
};
pinctrl_ipu1: ipu1grp {
fsl,pins = <
MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
>;
};
pinctrl_pcie: pciegrp {
fsl,pins = <
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b098
MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b098
MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b098
>;
};
pinctrl_pcie_reg: pciereggrp {
fsl,pins = <
MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b098
>;
};
pinctrl_pmic: pmicgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b098
>;
};
pinctrl_pwm1: pwm1grp {
fsl,pins = <
MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
>;
};
pinctrl_touch: touchgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b098
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b098
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0a8
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0a8
>;
};
pinctrl_usbh1: usbh1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D30__USB_H1_OC 0x1b098
>;
};
pinctrl_usbh1_vbus: usbh1-vbus {
fsl,pins = <
MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x98
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1b098
MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b098
>;
};
pinctrl_usbotg_vbus: usbotg-vbus {
fsl,pins = <
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x98
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b018
MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b018
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
>;
};
pinctrl_usdhc4: usdhc4grp {
fsl,pins = <
MX6QDL_PAD_SD4_CMD__SD4_CMD 0x1f069
MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10069
MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17069
MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17069
MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17069
MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17069
MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17069
MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17069
MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17069
MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17069
>;
};
pinctrl_wdog: wdoggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__WDOG2_B 0x1b0b0
>;
};
};
&ipu1_di0_disp0 {
remote-endpoint = <&lcd_display_in>;
};
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
vpcie-supply = <&reg_pcie>;
status = "disabled";
};
&pwm1 {
#pwm-cells = <3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "disabled";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&usbh1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh1>;
vbus-supply = <&reg_usb_h1_vbus>;
status = "disabled";
};
&usbotg {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
vbus-supply = <&reg_usb_otg_vbus>;
srp-disable;
hnp-disable;
adp-disable;
status = "okay";
};
&usbphy1 {
fsl,tx-d-cal = <106>;
status = "okay";
};
&usbphy2 {
fsl,tx-d-cal = <109>;
status = "disabled";
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
bus-width = <4>;
cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
no-1-8-v;
keep-power-in-suspend;
wakeup-source;
vmmc-supply = <&sw2_reg>;
status = "disabled";
};
&usdhc4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc4>;
bus-width = <8>;
non-removable;
no-1-8-v;
keep-power-in-suspend;
vmmc-supply = <&sw2_reg>;
status = "okay";
};
&wdog1 {
status = "disabled";
};
&wdog2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdog>;
fsl,ext-reset-output;
status = "okay";
};
arch/arm/boot/dts/imx6dl-yapp4-draco.dts 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
//
// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6dl-yapp4-common.dtsi"
/ {
model = "Y Soft IOTA Draco i.MX6Solo board";
compatible = "ysoft,imx6dl-yapp4-draco", "fsl,imx6dl";
memory@10000000 {
device_type = "memory";
reg = <0x10000000 0x20000000>;
};
};
&backlight {
status = "okay";
};
&lcd_display {
status = "okay";
};
&leds {
status = "okay";
};
&panel {
status = "okay";
};
&pwm1 {
status = "okay";
};
&reg_usb_h1_vbus {
status = "okay";
};
&touchscreen {
status = "okay";
};
&usbh1 {
status = "okay";
};
&usbphy2 {
status = "okay";
};
&usdhc3 {
status = "okay";
};
arch/arm/boot/dts/imx6dl-yapp4-hydra.dts 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
//
// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6dl-yapp4-common.dtsi"
/ {
model = "Y Soft IOTA Hydra i.MX6DualLite board";
compatible = "ysoft,imx6dl-yapp4-hydra", "fsl,imx6dl";
memory@10000000 {
device_type = "memory";
reg = <0x10000000 0x80000000>;
};
};
&gpio_oled {
status = "okay";
};
&hdmi {
status = "okay";
};
&i2c3 {
status = "okay";
};
&leds {
status = "okay";
};
&oled {
status = "okay";
};
&pcie {
status = "okay";
};
&reg_pcie {
status = "okay";
};
&usdhc3 {
status = "okay";
};
arch/arm/boot/dts/imx6dl-yapp4-ursa.dts 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
//
// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6dl-yapp4-common.dtsi"
/ {
model = "Y Soft IOTA Ursa i.MX6Solo board";
compatible = "ysoft,imx6dl-yapp4-ursa", "fsl,imx6dl";
memory@10000000 {
device_type = "memory";
reg = <0x10000000 0x20000000>;
};
};
&backlight {
status = "okay";
};
&lcd_display {
status = "okay";
};
&panel {
status = "okay";
};
&pwm1 {
status = "okay";
};
&reg_usb_h1_vbus {
status = "okay";
};
&switch_ports {
/delete-node/ port@2;
};
&touchscreen {
status = "okay";
};
&usbh1 {
status = "okay";
};
&usbphy2 {
status = "okay";
};
arch/arm/boot/dts/imx6q-logicpd.dts 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
//
// Copyright (C) 2019 Logic PD, Inc.
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6-logicpd-som.dtsi"
#include "imx6-logicpd-baseboard.dtsi"
/ {
model = "Logic PD i.MX6QD SOM-M3";
compatible = "fsl,imx6q";
backlight: backlight-lvds {
compatible = "pwm-backlight";
pwms = <&pwm3 0 20000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
power-supply = <&reg_lcd>;
};
panel-lvds0 {
compatible = "okaya,rs800480t-7x0gp";
port {
panel_in_lvds0: endpoint {
remote-endpoint = <&lvds0_out>;
};
};
};
reg_lcd: regulator-lcd {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd_reg>;
compatible = "regulator-fixed";
regulator-name = "lcd_panel_pwr";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio4 17 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
vin-supply = <&reg_3v3>;
startup-delay-us = <500000>;
};
reg_lcd_reset: regulator-lcd-reset {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd_reset>;
compatible = "regulator-fixed";
regulator-name = "nLCD_RESET";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
vin-supply = <&reg_lcd>;
};
};
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
<&clks IMX6QDL_CLK_LDB_DI1_SEL>,
<&clks IMX6QDL_CLK_IPU1_DI0_PRE_SEL>,
<&clks IMX6QDL_CLK_IPU2_DI0_PRE_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
<&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
<&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
<&clks IMX6QDL_CLK_PLL2_PFD2_396M>;
};
&hdmi {
ddc-i2c-bus = <&i2c3>;
status = "okay";
};
&ldb {
status = "okay";
lvds-channel@0 {
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
status = "okay";
port@4 {
reg = <4>;
lvds0_out: endpoint {
remote-endpoint = <&panel_in_lvds0>;
};
};
};
};
&pwm3 {
status = "okay";
};
&reg_hdmi {
regulator-always-on; /* Without this, the level shifter on HDMI doesn't turn on */
};
&iomuxc {
pinctrl_lcd_reg: lcdreg {
fsl,pins = <
MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x100b0 /* R_LCD_PANEL_PWR */
>;
};
pinctrl_lcd_reset: lcdreset {
fsl,pins = <
MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0 /* LCD_nRESET */
>;
};
pinctrl_touchscreen: touchscreengrp {
fsl,pins = <
MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0 /* TOUCH_nPINTDAV */
>;
};
};
arch/arm/boot/dts/imx6q-tbs2910.dts
View file @ 42d61413
/* // SPDX-License-Identifier: GPL-2.0+ OR MIT
* Copyright 2014 Soeren Moch <smoch@web.de> //
* // Copyright 2014 Soeren Moch <smoch@web.de>
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this file; if not, write to the Free
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
* MA 02110-1301 USA
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/; /dts-v1/;
......
arch/arm/boot/dts/imx6qdl-apalis.dtsi
View file @ 42d61413
...@@ -332,11 +332,17 @@ stmpe811@41 { ...@@ -332,11 +332,17 @@ stmpe811@41 {
id = <0>; id = <0>;
blocks = <0x5>; blocks = <0x5>;
irq-trigger = <0x1>; irq-trigger = <0x1>;
/* 3.25 MHz ADC clock speed */
st,adc-freq = <1>;
/* 12-bit ADC */
st,mod-12b = <1>;
/* internal ADC reference */
st,ref-sel = <0>;
/* ADC converstion time: 80 clocks */
st,sample-time = <4>;
stmpe_touchscreen { stmpe_touchscreen {
compatible = "st,stmpe-ts"; compatible = "st,stmpe-ts";
/* 3.25 MHz ADC clock speed */
st,adc-freq = <1>;
/* 8 sample average control */ /* 8 sample average control */
st,ave-ctrl = <3>; st,ave-ctrl = <3>;
/* 7 length fractional part in z */ /* 7 length fractional part in z */
...@@ -346,17 +352,17 @@ stmpe_touchscreen { ...@@ -346,17 +352,17 @@ stmpe_touchscreen {
* current limit value * current limit value
*/ */
st,i-drive = <1>; st,i-drive = <1>;
/* 12-bit ADC */
st,mod-12b = <1>;
/* internal ADC reference */
st,ref-sel = <0>;
/* ADC converstion time: 80 clocks */
st,sample-time = <4>;
/* 1 ms panel driver settling time */ /* 1 ms panel driver settling time */
st,settling = <3>; st,settling = <3>;
/* 5 ms touch detect interrupt delay */ /* 5 ms touch detect interrupt delay */
st,touch-det-delay = <5>; st,touch-det-delay = <5>;
}; };
stmpe_adc {
compatible = "st,stmpe-adc";
/* forbid to use ADC channels 3-0 (touch) */
st,norequest-mask = <0x0F>;
};
}; };
}; };
...@@ -369,8 +375,8 @@ &i2c3 { ...@@ -369,8 +375,8 @@ &i2c3 {
pinctrl-names = "default", "recovery"; pinctrl-names = "default", "recovery";
pinctrl-0 = <&pinctrl_i2c3>; pinctrl-0 = <&pinctrl_i2c3>;
pinctrl-1 = <&pinctrl_i2c3_recovery>; pinctrl-1 = <&pinctrl_i2c3_recovery>;
scl-gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>; scl-gpios = <&gpio3 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>; sda-gpios = <&gpio3 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled"; status = "disabled";
}; };
......
arch/arm/boot/dts/imx6qdl-colibri.dtsi
View file @ 42d61413
...@@ -262,11 +262,17 @@ stmpe811@41 { ...@@ -262,11 +262,17 @@ stmpe811@41 {
id = <0>; id = <0>;
blocks = <0x5>; blocks = <0x5>;
irq-trigger = <0x1>; irq-trigger = <0x1>;
/* 3.25 MHz ADC clock speed */
st,adc-freq = <1>;
/* 12-bit ADC */
st,mod-12b = <1>;
/* internal ADC reference */
st,ref-sel = <0>;
/* ADC converstion time: 80 clocks */
st,sample-time = <4>;
stmpe_touchscreen { stmpe_touchscreen {
compatible = "st,stmpe-ts"; compatible = "st,stmpe-ts";
/* 3.25 MHz ADC clock speed */
st,adc-freq = <1>;
/* 8 sample average control */ /* 8 sample average control */
st,ave-ctrl = <3>; st,ave-ctrl = <3>;
/* 7 length fractional part in z */ /* 7 length fractional part in z */
...@@ -276,17 +282,17 @@ stmpe_touchscreen { ...@@ -276,17 +282,17 @@ stmpe_touchscreen {
* current limit value * current limit value
*/ */
st,i-drive = <1>; st,i-drive = <1>;
/* 12-bit ADC */
st,mod-12b = <1>;
/* internal ADC reference */
st,ref-sel = <0>;
/* ADC converstion time: 80 clocks */
st,sample-time = <4>;
/* 1 ms panel driver settling time */ /* 1 ms panel driver settling time */
st,settling = <3>; st,settling = <3>;
/* 5 ms touch detect interrupt delay */ /* 5 ms touch detect interrupt delay */
st,touch-det-delay = <5>; st,touch-det-delay = <5>;
}; };
stmpe_adc {
compatible = "st,stmpe-adc";
/* forbid to use ADC channels 3-0 (touch) */
st,norequest-mask = <0x0F>;
};
}; };
}; };
...@@ -298,8 +304,8 @@ &i2c3 { ...@@ -298,8 +304,8 @@ &i2c3 {
pinctrl-names = "default", "recovery"; pinctrl-names = "default", "recovery";
pinctrl-0 = <&pinctrl_i2c3>; pinctrl-0 = <&pinctrl_i2c3>;
pinctrl-1 = <&pinctrl_i2c3_recovery>; pinctrl-1 = <&pinctrl_i2c3_recovery>;
scl-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled"; status = "disabled";
}; };
......
arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
View file @ 42d61413
...@@ -89,10 +89,23 @@ flash@0 { ...@@ -89,10 +89,23 @@ flash@0 {
&fec { &fec {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>; pinctrl-0 = <&pinctrl_enet>;
phy-handle = <&ethphy>;
phy-mode = "rgmii"; phy-mode = "rgmii";
phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
phy-supply = <&vdd_eth_io_reg>; phy-supply = <&vdd_eth_io_reg>;
status = "disabled"; status = "disabled";
fec_mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
txc-skew-ps = <1680>;
rxc-skew-ps = <1860>;
};
};
}; };
&gpmi { &gpmi {
...@@ -117,6 +130,7 @@ pmic@58 { ...@@ -117,6 +130,7 @@ pmic@58 {
reg = <0x58>; reg = <0x58>;
interrupt-parent = <&gpio2>; interrupt-parent = <&gpio2>;
interrupts = <9 IRQ_TYPE_LEVEL_LOW>; /* active-low GPIO2_9 */ interrupts = <9 IRQ_TYPE_LEVEL_LOW>; /* active-low GPIO2_9 */
interrupt-controller;
regulators { regulators {
vddcore_reg: bcore1 { vddcore_reg: bcore1 {
......
arch/arm/boot/dts/imx6qdl-sabresd.dtsi
View file @ 42d61413
...@@ -64,7 +64,6 @@ reg_sensors: regulator-sensors { ...@@ -64,7 +64,6 @@ reg_sensors: regulator-sensors {
regulator-max-microvolt = <3300000>; regulator-max-microvolt = <3300000>;
gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>; gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
enable-active-high; enable-active-high;
regulator-always-on;
}; };
gpio-keys { gpio-keys {
...@@ -250,6 +249,8 @@ accelerometer@1c { ...@@ -250,6 +249,8 @@ accelerometer@1c {
pinctrl-0 = <&pinctrl_i2c1_mma8451_int>; pinctrl-0 = <&pinctrl_i2c1_mma8451_int>;
interrupt-parent = <&gpio1>; interrupt-parent = <&gpio1>;
interrupts = <18 IRQ_TYPE_LEVEL_LOW>; interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
vdd-supply = <&reg_sensors>;
vddio-supply = <&reg_sensors>;
}; };
ov5642: camera@3c { ov5642: camera@3c {
...@@ -440,6 +441,8 @@ magnetometer@e { ...@@ -440,6 +441,8 @@ magnetometer@e {
pinctrl-0 = <&pinctrl_i2c3_mag3110_int>; pinctrl-0 = <&pinctrl_i2c3_mag3110_int>;
interrupt-parent = <&gpio3>; interrupt-parent = <&gpio3>;
interrupts = <16 IRQ_TYPE_EDGE_RISING>; interrupts = <16 IRQ_TYPE_EDGE_RISING>;
vdd-supply = <&reg_sensors>;
vddio-supply = <&reg_sensors>;
}; };
light-sensor@44 { light-sensor@44 {
...@@ -449,6 +452,7 @@ light-sensor@44 { ...@@ -449,6 +452,7 @@ light-sensor@44 {
pinctrl-0 = <&pinctrl_i2c3_isl29023_int>; pinctrl-0 = <&pinctrl_i2c3_isl29023_int>;
interrupt-parent = <&gpio3>; interrupt-parent = <&gpio3>;
interrupts = <9 IRQ_TYPE_EDGE_FALLING>; interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
vcc-supply = <&reg_sensors>;
}; };
}; };
......
arch/arm/boot/dts/imx6sl.dtsi
View file @ 42d61413
...@@ -338,7 +338,7 @@ pwm1: pwm@2080000 { ...@@ -338,7 +338,7 @@ pwm1: pwm@2080000 {
compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm"; compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
reg = <0x02080000 0x4000>; reg = <0x02080000 0x4000>;
interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>; interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SL_CLK_PWM1>, clocks = <&clks IMX6SL_CLK_PERCLK>,
<&clks IMX6SL_CLK_PWM1>; <&clks IMX6SL_CLK_PWM1>;
clock-names = "ipg", "per"; clock-names = "ipg", "per";
}; };
...@@ -348,7 +348,7 @@ pwm2: pwm@2084000 { ...@@ -348,7 +348,7 @@ pwm2: pwm@2084000 {
compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm"; compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
reg = <0x02084000 0x4000>; reg = <0x02084000 0x4000>;
interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SL_CLK_PWM2>, clocks = <&clks IMX6SL_CLK_PERCLK>,
<&clks IMX6SL_CLK_PWM2>; <&clks IMX6SL_CLK_PWM2>;
clock-names = "ipg", "per"; clock-names = "ipg", "per";
}; };
...@@ -358,7 +358,7 @@ pwm3: pwm@2088000 { ...@@ -358,7 +358,7 @@ pwm3: pwm@2088000 {
compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm"; compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
reg = <0x02088000 0x4000>; reg = <0x02088000 0x4000>;
interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>; interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SL_CLK_PWM3>, clocks = <&clks IMX6SL_CLK_PERCLK>,
<&clks IMX6SL_CLK_PWM3>; <&clks IMX6SL_CLK_PWM3>;
clock-names = "ipg", "per"; clock-names = "ipg", "per";
}; };
...@@ -368,7 +368,7 @@ pwm4: pwm@208c000 { ...@@ -368,7 +368,7 @@ pwm4: pwm@208c000 {
compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm"; compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm";
reg = <0x0208c000 0x4000>; reg = <0x0208c000 0x4000>;
interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SL_CLK_PWM4>, clocks = <&clks IMX6SL_CLK_PERCLK>,
<&clks IMX6SL_CLK_PWM4>; <&clks IMX6SL_CLK_PWM4>;
clock-names = "ipg", "per"; clock-names = "ipg", "per";
}; };
......
arch/arm/boot/dts/imx6sx.dtsi
View file @ 42d61413
...@@ -785,6 +785,18 @@ pd_pu: power-domain@1 { ...@@ -785,6 +785,18 @@ pd_pu: power-domain@1 {
clocks = <&clks IMX6SX_CLK_GPU>; clocks = <&clks IMX6SX_CLK_GPU>;
}; };
pd_disp: power-domain@2 {
reg = <2>;
#power-domain-cells = <0>;
clocks = <&clks IMX6SX_CLK_PXP_AXI>,
<&clks IMX6SX_CLK_DISPLAY_AXI>,
<&clks IMX6SX_CLK_LCDIF1_PIX>,
<&clks IMX6SX_CLK_LCDIF_APB>,
<&clks IMX6SX_CLK_LCDIF2_PIX>,
<&clks IMX6SX_CLK_CSI>,
<&clks IMX6SX_CLK_VADC>;
};
pd_pci: power-domain@3 { pd_pci: power-domain@3 {
reg = <3>; reg = <3>;
#power-domain-cells = <0>; #power-domain-cells = <0>;
...@@ -1205,6 +1217,7 @@ pxp: pxp@2218000 { ...@@ -1205,6 +1217,7 @@ pxp: pxp@2218000 {
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SX_CLK_PXP_AXI>; clocks = <&clks IMX6SX_CLK_PXP_AXI>;
clock-names = "axi"; clock-names = "axi";
power-domains = <&pd_disp>;
status = "disabled"; status = "disabled";
}; };
...@@ -1226,6 +1239,7 @@ lcdif1: lcdif@2220000 { ...@@ -1226,6 +1239,7 @@ lcdif1: lcdif@2220000 {
<&clks IMX6SX_CLK_LCDIF_APB>, <&clks IMX6SX_CLK_LCDIF_APB>,
<&clks IMX6SX_CLK_DISPLAY_AXI>; <&clks IMX6SX_CLK_DISPLAY_AXI>;
clock-names = "pix", "axi", "disp_axi"; clock-names = "pix", "axi", "disp_axi";
power-domains = <&pd_disp>;
status = "disabled"; status = "disabled";
}; };
...@@ -1237,6 +1251,7 @@ lcdif2: lcdif@2224000 { ...@@ -1237,6 +1251,7 @@ lcdif2: lcdif@2224000 {
<&clks IMX6SX_CLK_LCDIF_APB>, <&clks IMX6SX_CLK_LCDIF_APB>,
<&clks IMX6SX_CLK_DISPLAY_AXI>; <&clks IMX6SX_CLK_DISPLAY_AXI>;
clock-names = "pix", "axi", "disp_axi"; clock-names = "pix", "axi", "disp_axi";
power-domains = <&pd_disp>;
status = "disabled"; status = "disabled";
}; };
...@@ -1246,6 +1261,7 @@ vadc: vadc@2228000 { ...@@ -1246,6 +1261,7 @@ vadc: vadc@2228000 {
clocks = <&clks IMX6SX_CLK_VADC>, clocks = <&clks IMX6SX_CLK_VADC>,
<&clks IMX6SX_CLK_CSI>; <&clks IMX6SX_CLK_CSI>;
clock-names = "vadc", "csi"; clock-names = "vadc", "csi";
power-domains = <&pd_disp>;
status = "disabled"; status = "disabled";
}; };
}; };
...@@ -1370,7 +1386,8 @@ pcie: pcie@8ffc000 { ...@@ -1370,7 +1386,8 @@ pcie: pcie@8ffc000 {
<&clks IMX6SX_CLK_PCIE_REF_125M>, <&clks IMX6SX_CLK_PCIE_REF_125M>,
<&clks IMX6SX_CLK_DISPLAY_AXI>; <&clks IMX6SX_CLK_DISPLAY_AXI>;
clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_inbound_axi"; clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_inbound_axi";
power-domains = <&pd_pci>; power-domains = <&pd_disp>, <&pd_pci>;
power-domain-names = "pcie", "pcie_phy";
status = "disabled"; status = "disabled";
}; };
}; };
......
arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2016 PHYTEC Messtechnik GmbH
* Author: Christian Hemp <c.hemp@phytec.de>
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pwm/pwm.h>
#include "imx6ul.dtsi"
/ {
model = "Phytec phyCORE i.MX6 UltraLite";
compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
chosen {
stdout-path = &uart1;
};
/*
* Set the minimum memory size here and
* let the bootloader set the real size.
*/
memory {
device_type = "memory";
reg = <0x80000000 0x8000000>;
};
gpio_leds_som: leds {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpioleds_som>;
compatible = "gpio-leds";
led_green {
label = "phycore:green";
gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};
&fec1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet1>;
phy-mode = "rmii";
phy-handle = <&ethphy0>;
status = "okay";
mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy0: ethernet-phy@1 {
reg = <1>;
interrupt-parent = <&gpio1>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
micrel,led-mode = <1>;
clocks = <&clks IMX6UL_CLK_ENET_REF>;
clock-names = "rmii-ref";
};
};
};
&gpmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpmi_nand>;
nand-on-flash-bbt;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 =<&pinctrl_i2c1>;
clock-frequency = <100000>;
status = "okay";
eeprom@52 {
compatible = "catalyst,24c32", "atmel,24c32";
reg = <0x52>;
};
};
&snvs_poweroff {
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&iomuxc {
pinctrl_enet1: enet1grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x17059
>;
};
pinctrl_gpioleds_som: gpioledssomgrp {
fsl,pins = <MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0>;
};
pinctrl_gpmi_nand: gpminandgrp {
fsl,pins = <
MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
>;
};
pinctrl_i2c1: i2cgrp {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
>;
};
};
arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2016 PHYTEC Messtechnik
* Author: Christian Hemp <c.hemp@phytec.de>
*/
#include <dt-bindings/input/input.h>
/ {
gpio_keys: gpio-keys {
compatible = "gpio-key";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_keys>;
status = "disabled";
power {
label = "Power Button";
gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
wakeup-source;
};
};
user_leds: leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_user_leds>;
status = "disabled";
led_yellow {
gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
led_red {
gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
};
};
&iomuxc {
pinctrl_gpio_keys: gpio_keysgrp {
fsl,pins = <
MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x79
>;
};
pinctrl_user_leds: user_ledsgrp {
fsl,pins = <
MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x79
MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x79
>;
};
};
arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2016 PHYTEC Messtechnik GmbH
* Author: Christian Hemp <c.hemp@phytec.de>
*/
/dts-v1/;
#include "imx6ul-phytec-pcl063.dtsi"
#include "imx6ul-phytec-phyboard-segin.dtsi"
#include "imx6ul-phytec-peb-eval-01.dtsi"
/ {
model = "Phytec phyBOARD-Segin i.MX6 UltraLite Full Featured";
compatible = "phytec,imx6ul-pbacd10", "phytec,imx6ul-pcl063", "fsl,imx6ul";
};
&adc1 {
status = "okay";
};
&can1 {
status = "okay";
};
&tlv320 {
status = "okay";
};
&ecspi3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi3>;
cs-gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&fec2 {
status = "okay";
};
&i2c_rtc {
status = "okay";
};
&reg_can1_en {
status = "okay";
};
&reg_sound_1v8 {
status = "okay";
};
&reg_sound_3v3 {
status = "okay";
};
&sai2 {
status = "okay";
};
&sound {
status = "okay";
};
&uart5 {
status = "okay";
};
&usbotg1 {
status = "okay";
};
&usbotg2 {
status = "okay";
};
&usdhc1 {
status = "okay";
};
&iomuxc {
pinctrl_ecspi3: ecspi3grp {
fsl,pins = <
MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b0
MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b0
MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b0
MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x10b0
>;
};
};
arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (C) 2016 PHYTEC Messtechnik GmbH
* Author: Christian Hemp <c.hemp@phytec.de>
*/
/ {
model = "Phytec phyBOARD-Segin i.MX6 UltraLite";
compatible = "phytec,imx6ul-pbacd-10", "phytec,imx6ul-pcl063", "fsl,imx6ul";
aliases {
rtc0 = &i2c_rtc;
rtc1 = &snvs_rtc;
};
reg_sound_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "i2s-audio-1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
status = "disabled";
};
reg_sound_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "i2s-audio-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
status = "disabled";
};
reg_can1_en: regulator-can1 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&princtrl_flexcan1_en>;
regulator-name = "Can";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
status = "disabled";
};
reg_adc1_vref_3v3: regulator-vref-3v3 {
compatible = "regulator-fixed";
regulator-name = "vref-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
sound: sound {
compatible = "simple-audio-card";
simple-audio-card,name = "phyBOARD-Segin-TLV320AIC3007";
simple-audio-card,format = "i2s";
simple-audio-card,bitclock-master = <&dailink_master>;
simple-audio-card,frame-master = <&dailink_master>;
simple-audio-card,widgets =
"Line", "Line In",
"Line", "Line Out",
"Speaker", "Speaker";
simple-audio-card,routing =
"Line Out", "LLOUT",
"Line Out", "RLOUT",
"Speaker", "SPOP",
"Speaker", "SPOM",
"LINE1L", "Line In",
"LINE1R", "Line In";
status = "disabled";
simple-audio-card,cpu {
sound-dai = <&sai2>;
};
dailink_master: simple-audio-card,codec {
sound-dai = <&tlv320>;
clocks = <&clks IMX6UL_CLK_SAI2>;
};
};
};
&adc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_adc1>;
vref-supply = <&reg_adc1_vref_3v3>;
/*
* driver can not separate a specific channel so we request 4 channels
* here - we need only the fourth channel
*/
num-channels = <4>;
status = "disabled";
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan1>;
xceiver-supply = <&reg_can1_en>;
status = "disabled";
};
&clks {
assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
assigned-clock-rates = <786432000>;
};
&fec2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet2>;
phy-mode = "rmii";
phy-handle = <&ethphy1>;
status = "disabled";
};
&i2c1 {
tlv320: codec@18 {
compatible = "ti,tlv320aic3007";
#sound-dai-cells = <0>;
reg = <0x18>;
AVDD-supply = <&reg_sound_3v3>;
IOVDD-supply = <&reg_sound_3v3>;
DRVDD-supply = <&reg_sound_3v3>;
DVDD-supply = <&reg_sound_1v8>;
status = "disabled";
};
stmpe: touchscreen@44 {
compatible = "st,stmpe811";
reg = <0x44>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
interrupt-parent = <&gpio5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_stmpe>;
status = "disabled";
touchscreen {
compatible = "st,stmpe-ts";
st,sample-time = <4>;
st,mod-12b = <1>;
st,ref-sel = <0>;
st,adc-freq = <1>;
st,ave-ctrl = <1>;
st,touch-det-delay = <2>;
st,settling = <2>;
st,fraction-z = <7>;
st,i-drive = <1>;
touchscreen-inverted-x = <1>;
touchscreen-inverted-y = <1>;
};
};
i2c_rtc: rtc@68 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_rtc_int>;
compatible = "microcrystal,rv4162";
reg = <0x68>;
interrupt-parent = <&gpio5>;
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
status = "disabled";
};
};
&mdio {
ethphy1: ethernet-phy@2 {
reg = <2>;
micrel,led-mode = <1>;
clocks = <&clks IMX6UL_CLK_ENET2_REF>;
clock-names = "rmii-ref";
};
};
&pwm3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "disabled";
};
&sai2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sai2>;
assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
<&clks IMX6UL_CLK_SAI2>;
assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
assigned-clock-rates = <0>, <19200000>;
fsl,sai-mclk-direction-output;
status = "disabled";
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
uart-has-rtscts;
status = "disabled";
};
&usbotg1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb_otg1_id>;
dr_mode = "otg";
status = "disabled";
};
&usbotg2 {
dr_mode = "host";
disable-over-current;
status = "disabled";
};
&usdhc1 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>;
pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
no-1-8-v;
keep-power-in-suspend;
wakeup-source;
status = "disabled";
};
&iomuxc {
pinctrl_adc1: adc1grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
>;
};
pinctrl_enet2: enet2grp {
fsl,pins = <
MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031
>;
};
pinctrl_flexcan1: flexcan1 {
fsl,pins = <
MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
>;
};
princtrl_flexcan1_en: flexcan1engrp {
fsl,pins = <
MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x17059
>;
};
pinctrl_pwm3: pwm3grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO04__PWM3_OUT 0x0b0b0
>;
};
pinctrl_rtc_int: rtcintgrp {
fsl,pins = <
MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x17059
>;
};
pinctrl_sai2: sai2grp {
fsl,pins = <
MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088
MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088
MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088
>;
};
pinctrl_stmpe: stmpegrp {
fsl,pins = <
MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059
>;
};
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1
MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1
>;
};
pinctrl_usb_otg1_id: usbotg1idgrp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
>;
};
pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
>;
};
pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
>;
};
};
arch/arm/boot/dts/imx6ull-colibri.dtsi
View file @ 42d61413
...@@ -94,16 +94,16 @@ &i2c1 { ...@@ -94,16 +94,16 @@ &i2c1 {
pinctrl-names = "default", "gpio"; pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>; pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>; pinctrl-1 = <&pinctrl_i2c1_gpio>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
}; };
&i2c2 { &i2c2 {
pinctrl-names = "default", "gpio"; pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>; pinctrl-0 = <&pinctrl_i2c2>;
pinctrl-1 = <&pinctrl_i2c2_gpio>; pinctrl-1 = <&pinctrl_i2c2_gpio>;
sda-gpios = <&gpio1 31 GPIO_ACTIVE_LOW>; sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay"; status = "okay";
ad7879@2c { ad7879@2c {
......
arch/arm/boot/dts/imx6ull.dtsi
View file @ 42d61413
...@@ -30,6 +30,18 @@ &cpu0 { ...@@ -30,6 +30,18 @@ &cpu0 {
>; >;
}; };
&ocotp {
compatible = "fsl,imx6ull-ocotp", "syscon";
};
&usdhc1 {
compatible = "fsl,imx6ull-usdhc", "fsl,imx6sx-usdhc";
};
&usdhc2 {
compatible = "fsl,imx6ull-usdhc", "fsl,imx6sx-usdhc";
};
/ { / {
soc { soc {
aips3: aips-bus@2200000 { aips3: aips-bus@2200000 {
......
arch/arm/boot/dts/imx7ulp.dtsi
View file @ 42d61413
...@@ -199,9 +199,13 @@ pcc2: clock-controller@403f0000 { ...@@ -199,9 +199,13 @@ pcc2: clock-controller@403f0000 {
assigned-clock-parents = <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>; assigned-clock-parents = <&scg1 IMX7ULP_CLK_SOSC_BUS_CLK>;
}; };
smc1: smc1@40410000 { smc1: clock-controller@40410000 {
compatible = "fsl,imx7ulp-smc1"; compatible = "fsl,imx7ulp-smc1";
reg = <0x40410000 0x1000>; reg = <0x40410000 0x1000>;
#clock-cells = <1>;
clocks = <&scg1 IMX7ULP_CLK_CORE_DIV>,
<&scg1 IMX7ULP_CLK_HSRUN_CORE_DIV>;
clock-names = "divcore", "hsrun_divcore";
}; };
pcc3: clock-controller@40b30000 { pcc3: clock-controller@40b30000 {
...@@ -343,4 +347,17 @@ gpio_ptf: gpio@40b10000 { ...@@ -343,4 +347,17 @@ gpio_ptf: gpio@40b10000 {
gpio-ranges = <&iomuxc1 0 96 32>; gpio-ranges = <&iomuxc1 0 96 32>;
}; };
}; };
m4aips1: bus@41080000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x41080000 0x80000>;
ranges;
sim: sim@410a3000 {
compatible = "fsl,imx7ulp-sim", "syscon";
reg = <0x410a3000 0x1000>;
};
};
}; };
arch/arm/boot/dts/ls1021a-moxa-uc-8410a.dts
View file @ 42d61413
...@@ -18,6 +18,7 @@ ...@@ -18,6 +18,7 @@
/ { / {
model = "Moxa UC-8410A"; model = "Moxa UC-8410A";
compatible = "fsl,ls1021a-moxa-uc-8410a", "fsl,ls1021a";
aliases { aliases {
enet0_rgmii_phy = &rgmii_phy0; enet0_rgmii_phy = &rgmii_phy0;
......
arch/arm/boot/dts/ls1021a-qds.dts
View file @ 42d61413
...@@ -51,6 +51,7 @@ ...@@ -51,6 +51,7 @@
/ { / {
model = "LS1021A QDS Board"; model = "LS1021A QDS Board";
compatible = "fsl,ls1021a-qds", "fsl,ls1021a";
aliases { aliases {
enet0_rgmii_phy = &rgmii_phy1; enet0_rgmii_phy = &rgmii_phy1;
......
arch/arm/boot/dts/ls1021a-twr.dts
View file @ 42d61413
...@@ -51,6 +51,7 @@ ...@@ -51,6 +51,7 @@
/ { / {
model = "LS1021A TWR Board"; model = "LS1021A TWR Board";
compatible = "fsl,ls1021a-twr", "fsl,ls1021a";
aliases { aliases {
enet2_rgmii_phy = &rgmii_phy1; enet2_rgmii_phy = &rgmii_phy1;
......
arch/arm/boot/dts/ls1021a.dtsi
View file @ 42d61413
...@@ -131,6 +131,13 @@ soc { ...@@ -131,6 +131,13 @@ soc {
interrupt-parent = <&gic>; interrupt-parent = <&gic>;
ranges; ranges;
ddr: memory-controller@1080000 {
compatible = "fsl,qoriq-memory-controller";
reg = <0x0 0x1080000 0x0 0x1000>;
interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
big-endian;
};
gic: interrupt-controller@1400000 { gic: interrupt-controller@1400000 {
compatible = "arm,gic-400", "arm,cortex-a7-gic"; compatible = "arm,gic-400", "arm,cortex-a7-gic";
#interrupt-cells = <3>; #interrupt-cells = <3>;
...@@ -817,6 +824,7 @@ usb3: usb3@3100000 { ...@@ -817,6 +824,7 @@ usb3: usb3@3100000 {
dr_mode = "host"; dr_mode = "host";
snps,quirk-frame-length-adjustment = <0x20>; snps,quirk-frame-length-adjustment = <0x20>;
snps,dis_rxdet_inp3_quirk; snps,dis_rxdet_inp3_quirk;
snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
}; };
pcie@3400000 { pcie@3400000 {
...@@ -830,6 +838,7 @@ pcie@3400000 { ...@@ -830,6 +838,7 @@ pcie@3400000 {
#size-cells = <2>; #size-cells = <2>;
device_type = "pci"; device_type = "pci";
num-lanes = <4>; num-lanes = <4>;
num-viewport = <6>;
bus-range = <0x0 0xff>; bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */
0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
...@@ -854,6 +863,7 @@ pcie@3500000 { ...@@ -854,6 +863,7 @@ pcie@3500000 {
#size-cells = <2>; #size-cells = <2>;
device_type = "pci"; device_type = "pci";
num-lanes = <4>; num-lanes = <4>;
num-viewport = <6>;
bus-range = <0x0 0xff>; bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000 /* downstream I/O */ ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000 /* downstream I/O */
0x82000000 0x0 0x40000000 0x48 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ 0x82000000 0x0 0x40000000 0x48 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
......
arch/arm/boot/dts/vf610-bk4.dts
View file @ 42d61413
...@@ -60,6 +60,29 @@ reg_vcc_3v3_mcu: regulator-vcc3v3mcu { ...@@ -60,6 +60,29 @@ reg_vcc_3v3_mcu: regulator-vcc3v3mcu {
regulator-min-microvolt = <3300000>; regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>; regulator-max-microvolt = <3300000>;
}; };
spi-gpio {
compatible = "spi-gpio";
pinctrl-0 = <&pinctrl_gpio_spi>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
/* PTD12 ->RPIO[91] */
sck-gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
/* PTD10 ->RPIO[89] */
miso-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
num-chipselects = <0>;
gpio@0 {
compatible = "pisosr-gpio";
reg = <0>;
gpio-controller;
#gpio-cells = <2>;
/* PTB18 -> RGPIO[40] */
load-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
spi-max-frequency = <100000>;
};
};
}; };
&adc0 { &adc0 {
...@@ -431,6 +454,14 @@ VF610_PAD_PTE16__GPIO_121 0x1183 ...@@ -431,6 +454,14 @@ VF610_PAD_PTE16__GPIO_121 0x1183
>; >;
}; };
pinctrl_gpio_spi: pinctrl-gpio-spi {
fsl,pins = <
VF610_PAD_PTB18__GPIO_40 0x1183
VF610_PAD_PTD10__GPIO_89 0x1183
VF610_PAD_PTD12__GPIO_91 0x1183
>;
};
pinctrl_i2c2: i2c2grp { pinctrl_i2c2: i2c2grp {
fsl,pins = < fsl,pins = <
VF610_PAD_PTA22__I2C2_SCL 0x34df VF610_PAD_PTA22__I2C2_SCL 0x34df
......
arch/arm/boot/dts/vf610-zii-cfu1.dts
View file @ 42d61413
...@@ -207,7 +207,7 @@ fixed-link { ...@@ -207,7 +207,7 @@ fixed-link {
}; };
&i2c0 { &i2c0 {
clock-frequency = <100000>; clock-frequency = <400000>;
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c0>; pinctrl-0 = <&pinctrl_i2c0>;
status = "okay"; status = "okay";
......
arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts 0 → 100644
View file @ 42d61413
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/*
* Device tree file for ZII's SSMB DTU board
*
* SSMB - SPU3 Switch Management Board
* DTU - Digital Tapping Unit
*
* Copyright (C) 2015-2019 Zodiac Inflight Innovations
*
* Based on an original 'vf610-twr.dts' which is Copyright 2015,
* Freescale Semiconductor, Inc.
*/
/dts-v1/;
#include "vf610.dtsi"
/ {
model = "ZII VF610 SSMB DTU Board";
compatible = "zii,vf610dtu", "zii,vf610dev", "fsl,vf610";
chosen {
stdout-path = &uart0;
};
memory@80000000 {
device_type = "memory";
reg = <0x80000000 0x20000000>;
};
gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&pinctrl_leds_debug>;
pinctrl-names = "default";
led-debug {
label = "zii:green:debug1";
gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
max-brightness = <1>;
};
};
reg_vcc_3v3_mcu: regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_3v3_mcu";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
&adc0 {
vref-supply = <&reg_vcc_3v3_mcu>;
status = "okay";
};
&adc1 {
vref-supply = <&reg_vcc_3v3_mcu>;
status = "okay";
};
&edma0 {
status = "okay";
};
&edma1 {
status = "okay";
};
&esdhc0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc0>;
bus-width = <8>;
non-removable;
no-1-8-v;
keep-power-in-suspend;
status = "okay";
};
&esdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc1>;
bus-width = <4>;
status = "okay";
};
&fec1 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec1>;
status = "okay";
fixed-link {
speed = <100>;
full-duplex;
};
mdio1: mdio {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
switch0: switch0@0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
pinctrl-names = "default";
reg = <0>;
eeprom-length = <65536>;
reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio3>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <2>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "cpu";
ethernet = <&fec1>;
fixed-link {
speed = <100>;
full-duplex;
};
};
port@1 {
reg = <1>;
label = "eth_cu_100_3";
};
port@5 {
reg = <5>;
label = "eth_cu_1000_4";
};
port@6 {
reg = <6>;
label = "eth_cu_1000_5";
};
port@8 {
reg = <8>;
label = "eth_cu_1000_1";
};
port@9 {
reg = <9>;
label = "eth_cu_1000_2";
phy-handle = <&phy9>;
phy-mode = "sgmii";
managed = "in-band-status";
};
};
mdio1 {
compatible = "marvell,mv88e6xxx-mdio-external";
#address-cells = <1>;
#size-cells = <0>;
phy9: phy9@0 {
compatible = "ethernet-phy-ieee802.3-c45";
pinctrl-0 = <&pinctrl_gpio_phy9>;
pinctrl-names = "default";
interrupt-parent = <&gpio2>;
interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
reg = <0>;
};
};
};
};
};
&i2c0 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c0>;
status = "okay";
gpio6: gpio-expander@22 {
compatible = "nxp,pca9554";
reg = <0x22>;
gpio-controller;
#gpio-cells = <2>;
};
/* On SSMB */
temperature-sensor@48 {
compatible = "national,lm75";
reg = <0x48>;
};
/* On DSB */
temperature-sensor@4d {
compatible = "national,lm75";
reg = <0x4d>;
};
eeprom@50 {
compatible = "atmel,24c04";
reg = <0x50>;
label = "nameplate";
};
eeprom@52 {
compatible = "atmel,24c04";
reg = <0x52>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
status = "okay";
};
&iomuxc {
pinctrl_dspi1: dspi1grp {
fsl,pins = <
VF610_PAD_PTD5__DSPI1_CS0 0x1182
VF610_PAD_PTD4__DSPI1_CS1 0x1182
VF610_PAD_PTC6__DSPI1_SIN 0x1181
VF610_PAD_PTC7__DSPI1_SOUT 0x1182
VF610_PAD_PTC8__DSPI1_SCK 0x1182
>;
};
pinctrl_esdhc0: esdhc0grp {
fsl,pins = <
VF610_PAD_PTC0__ESDHC0_CLK 0x31ef
VF610_PAD_PTC1__ESDHC0_CMD 0x31ef
VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef
VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef
VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef
VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef
VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef
VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef
VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef
VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef
>;
};
pinctrl_esdhc1: esdhc1grp {
fsl,pins = <
VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
>;
};
pinctrl_fec1: fec1grp {
fsl,pins = <
VF610_PAD_PTA6__RMII_CLKIN 0x30d1
VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2
VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
>;
};
pinctrl_gpio_phy9: pinctrl-gpio-phy9 {
fsl,pins = <
VF610_PAD_PTB24__GPIO_94 0x219d
>;
};
pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
fsl,pins = <
VF610_PAD_PTE2__GPIO_107 0x31c2
VF610_PAD_PTB28__GPIO_98 0x219d
>;
};
pinctrl_i2c0: i2c0grp {
fsl,pins = <
VF610_PAD_PTB14__I2C0_SCL 0x37ff
VF610_PAD_PTB15__I2C0_SDA 0x37ff
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
VF610_PAD_PTB16__I2C1_SCL 0x37ff
VF610_PAD_PTB17__I2C1_SDA 0x37ff
>;
};
pinctrl_leds_debug: pinctrl-leds-debug {
fsl,pins = <
VF610_PAD_PTD3__GPIO_82 0x31c2
>;
};
pinctrl_uart0: uart0grp {
fsl,pins = <
VF610_PAD_PTB10__UART0_TX 0x21a2
VF610_PAD_PTB11__UART0_RX 0x21a1
>;
};
};
arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
View file @ 42d61413
...@@ -99,6 +99,8 @@ &esdhc0 { ...@@ -99,6 +99,8 @@ &esdhc0 {
non-removable; non-removable;
no-1-8-v; no-1-8-v;
keep-power-in-suspend; keep-power-in-suspend;
no-sdio;
no-sd;
status = "okay"; status = "okay";
}; };
...@@ -106,6 +108,7 @@ &esdhc1 { ...@@ -106,6 +108,7 @@ &esdhc1 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc1>; pinctrl-0 = <&pinctrl_esdhc1>;
bus-width = <4>; bus-width = <4>;
no-sdio;
status = "okay"; status = "okay";
}; };
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7