[PATCH] USB: Add isp116x-hcd USB host controller driver

This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.

The driver:
 - is relatively small, meant for use on embedded platforms.
 - runs usbtests 1-14 without problems for days.
 - has been in use by 6-7 different people on ARM and PPC platforms,
   running a range of devices including USB hubs.
 - supports suspend/resume of both the platform device and the root hub;
   supports remote wakeup of the root hub (but NOT the platform device)
   by USB devices.
 - does NOT support ISO transfers (nobody has asked for them).
 - is PIO-only.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/Makefile

@@ -9,6 +9,7 @@ obj-$(CONFIG_USB)		+= core/
 obj-$(CONFIG_USB_MON)		+= mon/
 
 obj-$(CONFIG_USB_EHCI_HCD)	+= host/
+obj-$(CONFIG_USB_ISP116X_HCD)	+= host/
 obj-$(CONFIG_USB_OHCI_HCD)	+= host/
 obj-$(CONFIG_USB_UHCI_HCD)	+= host/
 obj-$(CONFIG_USB_SL811_HCD)	+= host/

drivers/usb/host/Kconfig

@@ -49,6 +49,19 @@ config USB_EHCI_ROOT_HUB_TT
 
 	  This supports the EHCI implementation from TransDimension Inc.
 
+config USB_ISP116X_HCD
+	tristate "ISP116X HCD support"
+	depends on USB
+	default N
+	---help---
+	  The ISP1160 and ISP1161 chips are USB host controllers. Enable this
+	  option if your board has this chip. If unsure, say N.
+
+	  This driver does not support isochronous transfers.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called isp116x-hcd.
+
 config USB_OHCI_HCD
 	tristate "OHCI HCD support"
 	depends on USB && USB_ARCH_HAS_OHCI

drivers/usb/host/Makefile

@@ -4,6 +4,7 @@
 #
 
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
+obj-$(CONFIG_USB_ISP116X_HCD)	+= isp116x-hcd.o
 obj-$(CONFIG_USB_OHCI_HCD)	+= ohci-hcd.o
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_SL811_HCD)	+= sl811-hcd.o

include/linux/usb_isp116x.h

+
+/*
+ * Board initialization code should put one of these into dev->platform_data
+ * and place the isp116x onto platform_bus.
+ */
+
+struct isp116x_platform_data {
+	/* Enable internal resistors on downstream ports */
+	unsigned sel15Kres:1;
+	/* Chip's internal clock won't be stopped in suspended state.
+	   Setting/unsetting this bit takes effect only if
+	   'remote_wakeup_enable' below is not set. */
+	unsigned clknotstop:1;
+	/* On-chip overcurrent protection */
+	unsigned oc_enable:1;
+	/* INT output polarity */
+	unsigned int_act_high:1;
+	/* INT edge or level triggered */
+	unsigned int_edge_triggered:1;
+	/* WAKEUP pin connected - NOT SUPPORTED  */
+	/* unsigned remote_wakeup_connected:1; */
+	/* Wakeup by devices on usb bus enabled */
+	unsigned remote_wakeup_enable:1;
+	/* Switch or not to switch (keep always powered) */
+	unsigned no_power_switching:1;
+	/* Ganged port power switching (0) or individual port
+	   power switching (1) */
+	unsigned power_switching_mode:1;
+	/* Given port_power, msec/2 after power on till power good */
+	u8 potpg;
+	/* Hardware reset set/clear. If implemented, this function must:
+	   if set == 0,   deassert chip's HW reset pin
+	   otherwise,     assert chip's HW reset pin       */
+	void (*reset) (struct device * dev, int set);
+	/* Hardware clock start/stop. If implemented, this function must:
+	   if start == 0,    stop the external clock
+	   otherwise,        start the external clock
+	 */
+	void (*clock) (struct device * dev, int start);
+	/* Inter-io delay (ns). The chip is picky about access timings; it
+	   expects at least:
+	   150ns delay between consecutive accesses to DATA_REG,
+	   300ns delay between access to ADDR_REG and DATA_REG
+	   OE, WE MUST NOT be changed during these intervals
+	 */
+	void (*delay) (struct device * dev, int delay);
+};