Merge branch 'net-hns3-enhance-capabilities-for-fibre-port'

Jian Shen says:

====================
net: hns3: enhance capabilities for fibre port

This patchset enhances more capabilities for fibre port,
include multipe media type identification, autoneg,
change port speed and FEC encoding.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/hisilicon/hns3/hnae3.h

@@ -120,6 +120,25 @@ enum hnae3_media_type {
 	HNAE3_MEDIA_TYPE_NONE,
 };
 
+/* must be consistent with definition in firmware */
+enum hnae3_module_type {
+	HNAE3_MODULE_TYPE_UNKNOWN	= 0x00,
+	HNAE3_MODULE_TYPE_FIBRE_LR	= 0x01,
+	HNAE3_MODULE_TYPE_FIBRE_SR	= 0x02,
+	HNAE3_MODULE_TYPE_AOC		= 0x03,
+	HNAE3_MODULE_TYPE_CR		= 0x04,
+	HNAE3_MODULE_TYPE_KR		= 0x05,
+	HNAE3_MODULE_TYPE_TP		= 0x06,
+
+};
+
+enum hnae3_fec_mode {
+	HNAE3_FEC_AUTO = 0,
+	HNAE3_FEC_BASER,
+	HNAE3_FEC_RS,
+	HNAE3_FEC_USER_DEF,
+};
+
 enum hnae3_reset_notify_type {
 	HNAE3_UP_CLIENT,
 	HNAE3_DOWN_CLIENT,
@@ -230,10 +249,10 @@ struct hnae3_ae_dev {
  *   non-ok
  * get_ksettings_an_result()
  *   Get negotiation status,speed and duplex
- * update_speed_duplex_h()
- *   Update hardware speed and duplex
  * get_media_type()
  *   Get media type of MAC
+ * check_port_speed()
+ *   Check target speed whether is supported
  * adjust_link()
  *   Adjust link status
  * set_loopback()
@@ -250,6 +269,8 @@ struct hnae3_ae_dev {
  *   set auto autonegotiation of pause frame use
  * get_autoneg()
  *   get auto autonegotiation of pause frame use
+ * restart_autoneg()
+ *   restart autonegotiation
  * get_coalesce_usecs()
  *   get usecs to delay a TX interrupt after a packet is sent
  * get_rx_max_coalesced_frames()
@@ -340,11 +361,15 @@ struct hnae3_ae_ops {
 	void (*get_ksettings_an_result)(struct hnae3_handle *handle,
 					u8 *auto_neg, u32 *speed, u8 *duplex);
 
-	int (*update_speed_duplex_h)(struct hnae3_handle *handle);
 	int (*cfg_mac_speed_dup_h)(struct hnae3_handle *handle, int speed,
 				   u8 duplex);
 
-	void (*get_media_type)(struct hnae3_handle *handle, u8 *media_type);
+	void (*get_media_type)(struct hnae3_handle *handle, u8 *media_type,
+			       u8 *module_type);
+	int (*check_port_speed)(struct hnae3_handle *handle, u32 speed);
+	void (*get_fec)(struct hnae3_handle *handle, u8 *fec_ability,
+			u8 *fec_mode);
+	int (*set_fec)(struct hnae3_handle *handle, u32 fec_mode);
 	void (*adjust_link)(struct hnae3_handle *handle, int speed, int duplex);
 	int (*set_loopback)(struct hnae3_handle *handle,
 			    enum hnae3_loop loop_mode, bool en);
@@ -360,6 +385,7 @@ struct hnae3_ae_ops {
 
 	int (*set_autoneg)(struct hnae3_handle *handle, bool enable);
 	int (*get_autoneg)(struct hnae3_handle *handle);
+	int (*restart_autoneg)(struct hnae3_handle *handle);
 
 	void (*get_coalesce_usecs)(struct hnae3_handle *handle,
 				   u32 *tx_usecs, u32 *rx_usecs);

drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c

@@ -604,6 +604,7 @@ static int hns3_get_link_ksettings(struct net_device *netdev,
 {
 	struct hnae3_handle *h = hns3_get_handle(netdev);
 	const struct hnae3_ae_ops *ops;
+	u8 module_type;
 	u8 media_type;
 	u8 link_stat;
 
@@ -612,7 +613,7 @@ static int hns3_get_link_ksettings(struct net_device *netdev,
 
 	ops = h->ae_algo->ops;
 	if (ops->get_media_type)
-		ops->get_media_type(h, &media_type);
+		ops->get_media_type(h, &media_type, &module_type);
 	else
 		return -EOPNOTSUPP;
 
@@ -622,7 +623,15 @@ static int hns3_get_link_ksettings(struct net_device *netdev,
 		hns3_get_ksettings(h, cmd);
 		break;
 	case HNAE3_MEDIA_TYPE_FIBER:
+		if (module_type == HNAE3_MODULE_TYPE_CR)
+			cmd->base.port = PORT_DA;
+		else
 			cmd->base.port = PORT_FIBRE;
+
+		hns3_get_ksettings(h, cmd);
+		break;
+	case HNAE3_MEDIA_TYPE_BACKPLANE:
+		cmd->base.port = PORT_NONE;
 		hns3_get_ksettings(h, cmd);
 		break;
 	case HNAE3_MEDIA_TYPE_COPPER:
@@ -650,10 +659,54 @@ static int hns3_get_link_ksettings(struct net_device *netdev,
 	return 0;
 }
 
+static int hns3_check_ksettings_param(struct net_device *netdev,
+				      const struct ethtool_link_ksettings *cmd)
+{
+	struct hnae3_handle *handle = hns3_get_handle(netdev);
+	const struct hnae3_ae_ops *ops = handle->ae_algo->ops;
+	u8 module_type = HNAE3_MODULE_TYPE_UNKNOWN;
+	u8 media_type = HNAE3_MEDIA_TYPE_UNKNOWN;
+	u8 autoneg;
+	u32 speed;
+	u8 duplex;
+	int ret;
+
+	if (ops->get_ksettings_an_result) {
+		ops->get_ksettings_an_result(handle, &autoneg, &speed, &duplex);
+		if (cmd->base.autoneg == autoneg && cmd->base.speed == speed &&
+		    cmd->base.duplex == duplex)
+			return 0;
+	}
+
+	if (ops->get_media_type)
+		ops->get_media_type(handle, &media_type, &module_type);
+
+	if (cmd->base.duplex != DUPLEX_FULL &&
+	    media_type != HNAE3_MEDIA_TYPE_COPPER) {
+		netdev_err(netdev,
+			   "only copper port supports half duplex!");
+		return -EINVAL;
+	}
+
+	if (ops->check_port_speed) {
+		ret = ops->check_port_speed(handle, cmd->base.speed);
+		if (ret) {
+			netdev_err(netdev, "unsupported speed\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
 static int hns3_set_link_ksettings(struct net_device *netdev,
 				   const struct ethtool_link_ksettings *cmd)
 {
-	/* Chip doesn't support this mode. */
+	struct hnae3_handle *handle = hns3_get_handle(netdev);
+	const struct hnae3_ae_ops *ops = handle->ae_algo->ops;
+	int ret = 0;
+
+	/* Chip don't support this mode. */
 	if (cmd->base.speed == SPEED_1000 && cmd->base.duplex == DUPLEX_HALF)
 		return -EINVAL;
 
@@ -661,7 +714,24 @@ static int hns3_set_link_ksettings(struct net_device *netdev,
 	if (netdev->phydev)
 		return phy_ethtool_ksettings_set(netdev->phydev, cmd);
 
+	if (handle->pdev->revision == 0x20)
 		return -EOPNOTSUPP;
+
+	ret = hns3_check_ksettings_param(netdev, cmd);
+	if (ret)
+		return ret;
+
+	if (ops->set_autoneg) {
+		ret = ops->set_autoneg(handle, cmd->base.autoneg);
+		if (ret)
+			return ret;
+	}
+
+	if (ops->cfg_mac_speed_dup_h)
+		ret = ops->cfg_mac_speed_dup_h(handle, cmd->base.speed,
+					       cmd->base.duplex);
+
+	return ret;
 }
 
 static u32 hns3_get_rss_key_size(struct net_device *netdev)
@@ -866,19 +936,36 @@ static int hns3_set_rxnfc(struct net_device *netdev, struct ethtool_rxnfc *cmd)
 
 static int hns3_nway_reset(struct net_device *netdev)
 {
+	struct hnae3_handle *handle = hns3_get_handle(netdev);
+	const struct hnae3_ae_ops *ops = handle->ae_algo->ops;
 	struct phy_device *phy = netdev->phydev;
+	int autoneg;
 
 	if (!netif_running(netdev))
 		return 0;
 
-	/* Only support nway_reset for netdev with phy attached for now */
-	if (!phy)
+	if (hns3_nic_resetting(netdev)) {
+		netdev_err(netdev, "dev resetting!");
+		return -EBUSY;
+	}
+
+	if (!ops->get_autoneg || !ops->restart_autoneg)
 		return -EOPNOTSUPP;
 
-	if (phy->autoneg != AUTONEG_ENABLE)
+	autoneg = ops->get_autoneg(handle);
+	if (autoneg != AUTONEG_ENABLE) {
+		netdev_err(netdev,
+			   "Autoneg is off, don't support to restart it\n");
 		return -EINVAL;
+	}
 
+	if (phy)
 		return genphy_restart_aneg(phy);
+
+	if (handle->pdev->revision == 0x20)
+		return -EOPNOTSUPP;
+
+	return ops->restart_autoneg(handle);
 }
 
 static void hns3_get_channels(struct net_device *netdev,
@@ -1124,6 +1211,81 @@ static void hns3_set_msglevel(struct net_device *netdev, u32 msg_level)
 	h->msg_enable = msg_level;
 }
 
+/* Translate local fec value into ethtool value. */
+static unsigned int loc_to_eth_fec(u8 loc_fec)
+{
+	u32 eth_fec = 0;
+
+	if (loc_fec & BIT(HNAE3_FEC_AUTO))
+		eth_fec |= ETHTOOL_FEC_AUTO;
+	if (loc_fec & BIT(HNAE3_FEC_RS))
+		eth_fec |= ETHTOOL_FEC_RS;
+	if (loc_fec & BIT(HNAE3_FEC_BASER))
+		eth_fec |= ETHTOOL_FEC_BASER;
+
+	/* if nothing is set, then FEC is off */
+	if (!eth_fec)
+		eth_fec = ETHTOOL_FEC_OFF;
+
+	return eth_fec;
+}
+
+/* Translate ethtool fec value into local value. */
+static unsigned int eth_to_loc_fec(unsigned int eth_fec)
+{
+	u32 loc_fec = 0;
+
+	if (eth_fec & ETHTOOL_FEC_OFF)
+		return loc_fec;
+
+	if (eth_fec & ETHTOOL_FEC_AUTO)
+		loc_fec |= BIT(HNAE3_FEC_AUTO);
+	if (eth_fec & ETHTOOL_FEC_RS)
+		loc_fec |= BIT(HNAE3_FEC_RS);
+	if (eth_fec & ETHTOOL_FEC_BASER)
+		loc_fec |= BIT(HNAE3_FEC_BASER);
+
+	return loc_fec;
+}
+
+static int hns3_get_fecparam(struct net_device *netdev,
+			     struct ethtool_fecparam *fec)
+{
+	struct hnae3_handle *handle = hns3_get_handle(netdev);
+	const struct hnae3_ae_ops *ops = handle->ae_algo->ops;
+	u8 fec_ability;
+	u8 fec_mode;
+
+	if (handle->pdev->revision == 0x20)
+		return -EOPNOTSUPP;
+
+	if (!ops->get_fec)
+		return -EOPNOTSUPP;
+
+	ops->get_fec(handle, &fec_ability, &fec_mode);
+
+	fec->fec = loc_to_eth_fec(fec_ability);
+	fec->active_fec = loc_to_eth_fec(fec_mode);
+
+	return 0;
+}
+
+static int hns3_set_fecparam(struct net_device *netdev,
+			     struct ethtool_fecparam *fec)
+{
+	struct hnae3_handle *handle = hns3_get_handle(netdev);
+	const struct hnae3_ae_ops *ops = handle->ae_algo->ops;
+	u32 fec_mode;
+
+	if (handle->pdev->revision == 0x20)
+		return -EOPNOTSUPP;
+
+	if (!ops->set_fec)
+		return -EOPNOTSUPP;
+	fec_mode = eth_to_loc_fec(fec->fec);
+	return ops->set_fec(handle, fec_mode);
+}
+
 static const struct ethtool_ops hns3vf_ethtool_ops = {
 	.get_drvinfo = hns3_get_drvinfo,
 	.get_ringparam = hns3_get_ringparam,
@@ -1177,6 +1339,8 @@ static const struct ethtool_ops hns3_ethtool_ops = {
 	.set_phys_id = hns3_set_phys_id,
 	.get_msglevel = hns3_get_msglevel,
 	.set_msglevel = hns3_set_msglevel,
+	.get_fecparam = hns3_get_fecparam,
+	.set_fecparam = hns3_set_fecparam,
 };
 
 void hns3_ethtool_set_ops(struct net_device *netdev)

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h

@@ -113,6 +113,7 @@ enum hclge_opcode_type {
 	HCLGE_OPC_MAC_TNL_INT_EN	= 0x0311,
 	HCLGE_OPC_CLEAR_MAC_TNL_INT	= 0x0312,
 	HCLGE_OPC_SERDES_LOOPBACK       = 0x0315,
+	HCLGE_OPC_CONFIG_FEC_MODE	= 0x031A,
 
 	/* PFC/Pause commands */
 	HCLGE_OPC_CFG_MAC_PAUSE_EN      = 0x0701,
@@ -244,7 +245,7 @@ enum hclge_opcode_type {
 	HCLGE_OPC_QUERY_NCL_CONFIG	= 0x7011,
 
 	/* SFP command */
-	HCLGE_OPC_SFP_GET_SPEED		= 0x7104,
+	HCLGE_OPC_GET_SFP_INFO		= 0x7104,
 
 	/* Error INT commands */
 	HCLGE_MAC_COMMON_INT_EN		= 0x030E,
@@ -599,9 +600,30 @@ struct hclge_config_auto_neg_cmd {
 	u8      rsv[20];
 };
 
-struct hclge_sfp_speed_cmd {
-	__le32	sfp_speed;
-	u32	rsv[5];
+struct hclge_sfp_info_cmd {
+	__le32 speed;
+	u8 query_type; /* 0: sfp speed, 1: active speed */
+	u8 active_fec;
+	u8 autoneg; /* autoneg state */
+	u8 autoneg_ability; /* whether support autoneg */
+	__le32 speed_ability; /* speed ability for current media */
+	__le32 module_type;
+	u8 rsv[8];
+};
+
+#define HCLGE_MAC_CFG_FEC_AUTO_EN_B	0
+#define HCLGE_MAC_CFG_FEC_MODE_S	1
+#define HCLGE_MAC_CFG_FEC_MODE_M	GENMASK(3, 1)
+#define HCLGE_MAC_CFG_FEC_SET_DEF_B	0
+#define HCLGE_MAC_CFG_FEC_CLR_DEF_B	1
+
+#define HCLGE_MAC_FEC_OFF		0
+#define HCLGE_MAC_FEC_BASER		1
+#define HCLGE_MAC_FEC_RS		2
+struct hclge_config_fec_cmd {
+	u8 fec_mode;
+	u8 default_config;
+	u8 rsv[22];
 };
 
 #define HCLGE_MAC_UPLINK_PORT		0x100

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h

@@ -189,6 +189,8 @@ enum HLCGE_PORT_TYPE {
 #define HCLGE_SUPPORT_25G_BIT		BIT(2)
 #define HCLGE_SUPPORT_50G_BIT		BIT(3)
 #define HCLGE_SUPPORT_100G_BIT		BIT(4)
+/* to be compatible with exsit board */
+#define HCLGE_SUPPORT_40G_BIT		BIT(5)
 #define HCLGE_SUPPORT_100M_BIT		BIT(6)
 #define HCLGE_SUPPORT_10M_BIT		BIT(7)
 #define HCLGE_SUPPORT_GE \
@@ -236,15 +238,25 @@ enum HCLGE_MAC_DUPLEX {
 	HCLGE_MAC_FULL
 };
 
+#define QUERY_SFP_SPEED		0
+#define QUERY_ACTIVE_SPEED	1
+
 struct hclge_mac {
 	u8 phy_addr;
 	u8 flag;
-	u8 media_type;
+	u8 media_type;	/* port media type, e.g. fibre/copper/backplane */
 	u8 mac_addr[ETH_ALEN];
 	u8 autoneg;
 	u8 duplex;
+	u8 support_autoneg;
+	u8 speed_type;	/* 0: sfp speed, 1: active speed */
 	u32 speed;
-	int link;	/* store the link status of mac & phy (if phy exit)*/
+	u32 speed_ability; /* speed ability supported by current media */
+	u32 module_type; /* sub media type, e.g. kr/cr/sr/lr */
+	u32 fec_mode; /* active fec mode */
+	u32 user_fec_mode;
+	u32 fec_ability;
+	int link;	/* store the link status of mac & phy (if phy exit) */
 	struct phy_device *phydev;
 	struct mii_bus *mdio_bus;
 	phy_interface_t phy_if;

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_mbx.c

@@ -412,10 +412,11 @@ static int hclge_get_vf_media_type(struct hclge_vport *vport,
 				   struct hclge_mbx_vf_to_pf_cmd *mbx_req)
 {
 	struct hclge_dev *hdev = vport->back;
-	u8 resp_data;
+	u8 resp_data[2];
 
-	resp_data = hdev->hw.mac.media_type;
-	return hclge_gen_resp_to_vf(vport, mbx_req, 0, &resp_data,
+	resp_data[0] = hdev->hw.mac.media_type;
+	resp_data[1] = hdev->hw.mac.module_type;
+	return hclge_gen_resp_to_vf(vport, mbx_req, 0, resp_data,
 				    sizeof(resp_data));
 }
 

drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c

@@ -330,11 +330,11 @@ static u16 hclgevf_get_qid_global(struct hnae3_handle *handle, u16 queue_id)
 
 static int hclgevf_get_pf_media_type(struct hclgevf_dev *hdev)
 {
-	u8 resp_msg;
+	u8 resp_msg[2];
 	int ret;
 
 	ret = hclgevf_send_mbx_msg(hdev, HCLGE_MBX_GET_MEDIA_TYPE, 0, NULL, 0,
-				   true, &resp_msg, sizeof(resp_msg));
+				   true, resp_msg, sizeof(resp_msg));
 	if (ret) {
 		dev_err(&hdev->pdev->dev,
 			"VF request to get the pf port media type failed %d",
@@ -342,7 +342,8 @@ static int hclgevf_get_pf_media_type(struct hclgevf_dev *hdev)
 		return ret;
 	}
 
-	hdev->hw.mac.media_type = resp_msg;
+	hdev->hw.mac.media_type = resp_msg[0];
+	hdev->hw.mac.module_type = resp_msg[1];
 
 	return 0;
 }
@@ -2747,12 +2748,16 @@ static int hclgevf_gro_en(struct hnae3_handle *handle, bool enable)
 	return hclgevf_config_gro(hdev, enable);
 }
 
-static void hclgevf_get_media_type(struct hnae3_handle *handle,
-				  u8 *media_type)
+static void hclgevf_get_media_type(struct hnae3_handle *handle, u8 *media_type,
+				   u8 *module_type)
 {
 	struct hclgevf_dev *hdev = hclgevf_ae_get_hdev(handle);
+
 	if (media_type)
 		*media_type = hdev->hw.mac.media_type;
+
+	if (module_type)
+		*module_type = hdev->hw.mac.module_type;
 }
 
 static bool hclgevf_get_hw_reset_stat(struct hnae3_handle *handle)

drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.h

@@ -143,6 +143,7 @@ enum hclgevf_states {
 
 struct hclgevf_mac {
 	u8 media_type;
+	u8 module_type;
 	u8 mac_addr[ETH_ALEN];
 	int link;
 	u8 duplex;