Merge tag 'phy-for-4.4' of...

Merge tag 'phy-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.4

*) Add new PHY driver for Broadcom's cygnus PCIe PHY
*) Add USB3 PHY driver for mediatek's SoCs
*) Add VBUS regulator support for Samsung's exynos PHY
*) Misc cleanup
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt

+Broadcom Cygnus PCIe PHY
+
+Required properties:
+- compatible: must be "brcm,cygnus-pcie-phy"
+- reg: base address and length of the PCIe PHY block
+- #address-cells: must be 1
+- #size-cells: must be 0
+
+Each PCIe PHY should be represented by a child node
+
+Required properties For the child node:
+- reg: the PHY ID
+0 - PCIe RC 0
+1 - PCIe RC 1
+- #phy-cells: must be 0
+
+Example:
+	pcie_phy: phy@0301d0a0 {
+		compatible = "brcm,cygnus-pcie-phy";
+		reg = <0x0301d0a0 0x14>;
+
+		pcie0_phy: phy@0 {
+			reg = <0>;
+			#phy-cells = <0>;
+		};
+
+		pcie1_phy: phy@1 {
+			reg = <1>;
+			#phy-cells = <0>;
+		};
+	};
+
+	/* users of the PCIe phy */
+
+	pcie0: pcie@18012000 {
+		...
+		...
+		phys = <&pcie0_phy>;
+		phy-names = "pcie-phy";
+	};
+
+	pcie1: pcie@18013000 {
+		...
+		...
+		phys = <pcie1_phy>;
+		phy-names = "pcie-phy";
+	};

Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt

+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible	: should be "mediatek,mt8173-u3phy"
+ - reg		: offset and length of register for phy, exclude port's
+		  register.
+ - clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+ - clock-names	: must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology.
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy@11290000 {
+	compatible = "mediatek,mt8173-u3phy";
+	reg = <0 0x11290000 0 0x800>;
+	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+	clock-names = "u3phya_ref";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+	status = "okay";
+
+	phy_port0: port@11290800 {
+		reg = <0 0x11290800 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+
+	phy_port1: port@11291000 {
+		reg = <0 0x11291000 0 0x800>;
+		#phy-cells = <1>;
+		status = "okay";
+	};
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb@11270000 {
+	...
+	phys = <&phy_port0 PHY_TYPE_USB3>;
+	phy-names = "usb3-0";
+	...
+};

Documentation/devicetree/bindings/phy/samsung-phy.txt

@@ -44,6 +44,9 @@ Required properties:
 	- the "ref" clock is used to get the rate of the clock provided to the
 	  PHY module
 
+Optional properties:
+- vbus-supply: power-supply phandle for vbus power source
+
 The first phandle argument in the PHY specifier identifies the PHY, its
 meaning is compatible dependent. For the currently supported SoCs (Exynos 4210
 and Exynos 4212) it is as follows:

MAINTAINERS

@@ -1297,6 +1297,13 @@ F:	arch/arm/mach-mediatek/
 N:	mtk
 K:	mediatek
 
+ARM/Mediatek USB3 PHY DRIVER
+M:	Chunfeng Yun <chunfeng.yun@mediatek.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	drivers/phy/phy-mt65xx-usb3.c
+
 ARM/MICREL KS8695 ARCHITECTURE
 M:	Greg Ungerer <gerg@uclinux.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)

drivers/phy/Kconfig

@@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
 	help
 	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
 
+config PHY_MT65XX_USB3
+	tristate "Mediatek USB3.0 PHY Driver"
+	depends on ARCH_MEDIATEK && OF
+	select GENERIC_PHY
+	help
+	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
+	  for mt65xx SoCs. it supports two usb2.0 ports and
+	  one usb3.0 port.
+
 config PHY_SUN4I_USB
 	tristate "Allwinner sunxi SoC USB PHY driver"
 	depends on ARCH_SUNXI && HAS_IOMEM && OF
@@ -371,4 +380,13 @@ config PHY_BRCMSTB_SATA
 	  Enable this to support the SATA3 PHY on 28nm Broadcom STB SoCs.
 	  Likely useful only with CONFIG_SATA_BRCMSTB enabled.
 
+config PHY_CYGNUS_PCIE
+	tristate "Broadcom Cygnus PCIe PHY driver"
+	depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST)
+	select GENERIC_PHY
+	default ARCH_BCM_CYGNUS
+	help
+	  Enable this to support the Broadcom Cygnus PCIe PHY.
+	  If unsure, say N.
+
 endmenu

drivers/phy/Makefile

@@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
 obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
 obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
 obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
+obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
 obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
 obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
@@ -46,3 +47,4 @@ obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-14nm.o
 obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
 obj-$(CONFIG_PHY_BRCMSTB_SATA)		+= phy-brcmstb-sata.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
+obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o

drivers/phy/phy-bcm-cygnus-pcie.c

+/*
+ * Copyright (C) 2015 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+#define PCIE_CFG_OFFSET         0x00
+#define PCIE1_PHY_IDDQ_SHIFT    10
+#define PCIE0_PHY_IDDQ_SHIFT    2
+
+enum cygnus_pcie_phy_id {
+	CYGNUS_PHY_PCIE0 = 0,
+	CYGNUS_PHY_PCIE1,
+	MAX_NUM_PHYS,
+};
+
+struct cygnus_pcie_phy_core;
+
+/**
+ * struct cygnus_pcie_phy - Cygnus PCIe PHY device
+ * @core: pointer to the Cygnus PCIe PHY core control
+ * @id: internal ID to identify the Cygnus PCIe PHY
+ * @phy: pointer to the kernel PHY device
+ */
+struct cygnus_pcie_phy {
+	struct cygnus_pcie_phy_core *core;
+	enum cygnus_pcie_phy_id id;
+	struct phy *phy;
+};
+
+/**
+ * struct cygnus_pcie_phy_core - Cygnus PCIe PHY core control
+ * @dev: pointer to device
+ * @base: base register
+ * @lock: mutex to protect access to individual PHYs
+ * @phys: pointer to Cygnus PHY device
+ */
+struct cygnus_pcie_phy_core {
+	struct device *dev;
+	void __iomem *base;
+	struct mutex lock;
+	struct cygnus_pcie_phy phys[MAX_NUM_PHYS];
+};
+
+static int cygnus_pcie_power_config(struct cygnus_pcie_phy *phy, bool enable)
+{
+	struct cygnus_pcie_phy_core *core = phy->core;
+	unsigned shift;
+	u32 val;
+
+	mutex_lock(&core->lock);
+
+	switch (phy->id) {
+	case CYGNUS_PHY_PCIE0:
+		shift = PCIE0_PHY_IDDQ_SHIFT;
+		break;
+
+	case CYGNUS_PHY_PCIE1:
+		shift = PCIE1_PHY_IDDQ_SHIFT;
+		break;
+
+	default:
+		mutex_unlock(&core->lock);
+		dev_err(core->dev, "PCIe PHY %d invalid\n", phy->id);
+		return -EINVAL;
+	}
+
+	if (enable) {
+		val = readl(core->base + PCIE_CFG_OFFSET);
+		val &= ~BIT(shift);
+		writel(val, core->base + PCIE_CFG_OFFSET);
+		/*
+		 * Wait 50 ms for the PCIe Serdes to stabilize after the analog
+		 * front end is brought up
+		 */
+		msleep(50);
+	} else {
+		val = readl(core->base + PCIE_CFG_OFFSET);
+		val |= BIT(shift);
+		writel(val, core->base + PCIE_CFG_OFFSET);
+	}
+
+	mutex_unlock(&core->lock);
+	dev_dbg(core->dev, "PCIe PHY %d %s\n", phy->id,
+		enable ? "enabled" : "disabled");
+	return 0;
+}
+
+static int cygnus_pcie_phy_power_on(struct phy *p)
+{
+	struct cygnus_pcie_phy *phy = phy_get_drvdata(p);
+
+	return cygnus_pcie_power_config(phy, true);
+}
+
+static int cygnus_pcie_phy_power_off(struct phy *p)
+{
+	struct cygnus_pcie_phy *phy = phy_get_drvdata(p);
+
+	return cygnus_pcie_power_config(phy, false);
+}
+
+static struct phy_ops cygnus_pcie_phy_ops = {
+	.power_on = cygnus_pcie_phy_power_on,
+	.power_off = cygnus_pcie_phy_power_off,
+	.owner = THIS_MODULE,
+};
+
+static int cygnus_pcie_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node, *child;
+	struct cygnus_pcie_phy_core *core;
+	struct phy_provider *provider;
+	struct resource *res;
+	unsigned cnt = 0;
+
+	if (of_get_child_count(node) == 0) {
+		dev_err(dev, "PHY no child node\n");
+		return -ENODEV;
+	}
+
+	core = devm_kzalloc(dev, sizeof(*core), GFP_KERNEL);
+	if (!core)
+		return -ENOMEM;
+
+	core->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	core->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(core->base))
+		return PTR_ERR(core->base);
+
+	mutex_init(&core->lock);
+
+	for_each_available_child_of_node(node, child) {
+		unsigned int id;
+		struct cygnus_pcie_phy *p;
+
+		if (of_property_read_u32(child, "reg", &id)) {
+			dev_err(dev, "missing reg property for %s\n",
+				child->name);
+			return -EINVAL;
+		}
+
+		if (id >= MAX_NUM_PHYS) {
+			dev_err(dev, "invalid PHY id: %u\n", id);
+			return -EINVAL;
+		}
+
+		if (core->phys[id].phy) {
+			dev_err(dev, "duplicated PHY id: %u\n", id);
+			return -EINVAL;
+		}
+
+		p = &core->phys[id];
+		p->phy = devm_phy_create(dev, child, &cygnus_pcie_phy_ops);
+		if (IS_ERR(p->phy)) {
+			dev_err(dev, "failed to create PHY\n");
+			return PTR_ERR(p->phy);
+		}
+
+		p->core = core;
+		p->id = id;
+		phy_set_drvdata(p->phy, p);
+		cnt++;
+	}
+
+	dev_set_drvdata(dev, core);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(provider)) {
+		dev_err(dev, "failed to register PHY provider\n");
+		return PTR_ERR(provider);
+	}
+
+	dev_dbg(dev, "registered %u PCIe PHY(s)\n", cnt);
+
+	return 0;
+}
+
+static const struct of_device_id cygnus_pcie_phy_match_table[] = {
+	{ .compatible = "brcm,cygnus-pcie-phy" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, cygnus_pcie_phy_match_table);
+
+static struct platform_driver cygnus_pcie_phy_driver = {
+	.driver = {
+		.name = "cygnus-pcie-phy",
+		.of_match_table = cygnus_pcie_phy_match_table,
+	},
+	.probe = cygnus_pcie_phy_probe,
+};
+module_platform_driver(cygnus_pcie_phy_driver);
+
+MODULE_AUTHOR("Ray Jui <rjui@broadcom.com>");
+MODULE_DESCRIPTION("Broadcom Cygnus PCIe PHY driver");
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-mt65xx-usb3.c

+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+/*
+ * for sifslv2 register, but exclude port's;
+ * relative to USB3_SIF2_BASE base address
+ */
+#define SSUSB_SIFSLV_SPLLC		0x0000
+
+/* offsets of sub-segment in each port registers */
+#define SSUSB_SIFSLV_U2PHY_COM_BASE	0x0000
+#define SSUSB_SIFSLV_U3PHYD_BASE	0x0100
+#define SSUSB_USB30_PHYA_SIV_B_BASE	0x0300
+#define SSUSB_SIFSLV_U3PHYA_DA_BASE	0x0400
+
+#define U3P_USBPHYACR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
+#define PA0_RG_U2PLL_FORCE_ON		BIT(15)
+
+#define U3P_USBPHYACR2		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
+#define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
+
+#define U3P_USBPHYACR5		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
+#define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
+#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
+#define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
+
+#define U3P_USBPHYACR6		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
+#define PA6_RG_U2_ISO_EN		BIT(31)
+#define PA6_RG_U2_BC11_SW_EN		BIT(23)
+#define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
+
+#define U3P_U2PHYACR4		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
+#define P2C_RG_USB20_GPIO_CTL		BIT(9)
+#define P2C_USB20_GPIO_MODE		BIT(8)
+#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
+
+#define U3D_U2PHYDCR0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
+#define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
+
+#define U3P_U2PHYDTM0		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
+#define P2C_FORCE_UART_EN		BIT(26)
+#define P2C_FORCE_DATAIN		BIT(23)
+#define P2C_FORCE_DM_PULLDOWN		BIT(21)
+#define P2C_FORCE_DP_PULLDOWN		BIT(20)
+#define P2C_FORCE_XCVRSEL		BIT(19)
+#define P2C_FORCE_SUSPENDM		BIT(18)
+#define P2C_FORCE_TERMSEL		BIT(17)
+#define P2C_RG_DATAIN			GENMASK(13, 10)
+#define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
+#define P2C_RG_DMPULLDOWN		BIT(7)
+#define P2C_RG_DPPULLDOWN		BIT(6)
+#define P2C_RG_XCVRSEL			GENMASK(5, 4)
+#define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
+#define P2C_RG_SUSPENDM			BIT(3)
+#define P2C_RG_TERMSEL			BIT(2)
+#define P2C_DTM0_PART_MASK \
+		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
+		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
+		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
+		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
+
+#define U3P_U2PHYDTM1		(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
+#define P2C_RG_UART_EN			BIT(16)
+#define P2C_RG_VBUSVALID		BIT(5)
+#define P2C_RG_SESSEND			BIT(4)
+#define P2C_RG_AVALID			BIT(2)
+
+#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
+#define P3A_RG_U3_VUSB10_ON		BIT(5)
+
+#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
+#define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
+#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
+
+#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
+#define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
+#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
+
+#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
+#define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
+#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
+
+#define U3P_PHYD_CDR1		(SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
+#define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
+#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
+#define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
+#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
+
+#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x0018)
+#define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
+#define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
+
+struct mt65xx_phy_instance {
+	struct phy *phy;
+	void __iomem *port_base;
+	u32 index;
+	u8 type;
+};
+
+struct mt65xx_u3phy {
+	struct device *dev;
+	void __iomem *sif_base;	/* include sif2, but exclude port's */
+	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
+	struct mt65xx_phy_instance **phys;
+	int nphys;
+};
+
+static void phy_instance_init(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	/* switch to USB function. (system register, force ip into usb mode) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_FORCE_UART_EN;
+	tmp |= P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0);
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~P2C_RG_UART_EN;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U2PHYACR4);
+		tmp &= ~P2C_U2_GPIO_CTR_MSK;
+		writel(tmp, port_base + U3P_U2PHYACR4);
+
+		tmp = readl(port_base + U3P_USBPHYACR2);
+		tmp |= PA2_RG_SIF_U2PLL_FORCE_EN;
+		writel(tmp, port_base + U3P_USBPHYACR2);
+
+		tmp = readl(port_base + U3D_U2PHYDCR0);
+		tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
+		writel(tmp, port_base + U3D_U2PHYDCR0);
+	} else {
+		tmp = readl(port_base + U3D_U2PHYDCR0);
+		tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
+		writel(tmp, port_base + U3D_U2PHYDCR0);
+
+		tmp = readl(port_base + U3P_U2PHYDTM0);
+		tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
+		writel(tmp, port_base + U3P_U2PHYDTM0);
+	}
+
+	/* DP/DM BC1.1 path Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_BC11_SW_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
+	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
+	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
+	writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG9);
+	tmp &= ~P3A_RG_RX_DAC_MUX;
+	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
+	writel(tmp, port_base + U3P_U3_PHYA_REG9);
+
+	tmp = readl(port_base + U3P_U3_PHYA_REG6);
+	tmp &= ~P3A_RG_TX_EIDLE_CM;
+	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
+	writel(tmp, port_base + U3P_U3_PHYA_REG6);
+
+	tmp = readl(port_base + U3P_PHYD_CDR1);
+	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
+	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
+	writel(tmp, port_base + U3P_PHYD_CDR1);
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	if (!index) {
+		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp |= P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	}
+
+	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
+	tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Enable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	if (!index) {
+		tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
+		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
+		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
+
+		/* [mt8173]disable Change 100uA current from SSUSB */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp |= P2C_RG_VBUSVALID | P2C_RG_AVALID;
+	tmp &= ~P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	/* USB 2.0 slew rate calibration */
+	tmp = readl(port_base + U3P_USBPHYACR5);
+	tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
+	tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(4);
+	writel(tmp, port_base + U3P_USBPHYACR5);
+
+	if (index) {
+		tmp = readl(port_base + U3D_U2PHYDCR0);
+		tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
+		writel(tmp, port_base + U3D_U2PHYDCR0);
+
+		tmp = readl(port_base + U3P_U2PHYDTM0);
+		tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
+		writel(tmp, port_base + U3P_U2PHYDTM0);
+	}
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_power_off(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN);
+	tmp |= P2C_FORCE_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+
+	/* OTG Disable */
+	tmp = readl(port_base + U3P_USBPHYACR6);
+	tmp &= ~PA6_RG_U2_OTG_VBUSCMP_EN;
+	writel(tmp, port_base + U3P_USBPHYACR6);
+
+	if (!index) {
+		/* (also disable)Change 100uA current switch to USB2.0 */
+		tmp = readl(port_base + U3P_USBPHYACR5);
+		tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
+		writel(tmp, port_base + U3P_USBPHYACR5);
+	}
+
+	/* let suspendm=0, set utmi into analog power down */
+	tmp = readl(port_base + U3P_U2PHYDTM0);
+	tmp &= ~P2C_RG_SUSPENDM;
+	writel(tmp, port_base + U3P_U2PHYDTM0);
+	udelay(1);
+
+	tmp = readl(port_base + U3P_U2PHYDTM1);
+	tmp &= ~(P2C_RG_VBUSVALID | P2C_RG_AVALID);
+	tmp |= P2C_RG_SESSEND;
+	writel(tmp, port_base + U3P_U2PHYDTM1);
+
+	if (!index) {
+		tmp = readl(port_base + U3P_U3_PHYA_REG0);
+		tmp &= ~P3A_RG_U3_VUSB10_ON;
+		writel(tmp, port_base + U3P_U3_PHYA_REG0);
+	} else {
+		tmp = readl(port_base + U3D_U2PHYDCR0);
+		tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
+		writel(tmp, port_base + U3D_U2PHYDCR0);
+	}
+
+	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
+}
+
+static void phy_instance_exit(struct mt65xx_u3phy *u3phy,
+	struct mt65xx_phy_instance *instance)
+{
+	void __iomem *port_base = instance->port_base;
+	u32 index = instance->index;
+	u32 tmp;
+
+	if (index) {
+		tmp = readl(port_base + U3D_U2PHYDCR0);
+		tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
+		writel(tmp, port_base + U3D_U2PHYDCR0);
+
+		tmp = readl(port_base + U3P_U2PHYDTM0);
+		tmp &= ~P2C_FORCE_SUSPENDM;
+		writel(tmp, port_base + U3P_U2PHYDTM0);
+	}
+}
+
+static int mt65xx_phy_init(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	ret = clk_prepare_enable(u3phy->u3phya_ref);
+	if (ret) {
+		dev_err(u3phy->dev, "failed to enable u3phya_ref\n");
+		return ret;
+	}
+
+	phy_instance_init(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_on(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_on(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_power_off(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_power_off(u3phy, instance);
+	return 0;
+}
+
+static int mt65xx_phy_exit(struct phy *phy)
+{
+	struct mt65xx_phy_instance *instance = phy_get_drvdata(phy);
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(phy->dev.parent);
+
+	phy_instance_exit(u3phy, instance);
+	clk_disable_unprepare(u3phy->u3phya_ref);
+	return 0;
+}
+
+static struct phy *mt65xx_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct mt65xx_u3phy *u3phy = dev_get_drvdata(dev);
+	struct mt65xx_phy_instance *instance = NULL;
+	struct device_node *phy_np = args->np;
+	int index;
+
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	for (index = 0; index < u3phy->nphys; index++)
+		if (phy_np == u3phy->phys[index]->phy->dev.of_node) {
+			instance = u3phy->phys[index];
+			break;
+		}
+
+	if (!instance) {
+		dev_err(dev, "failed to find appropriate phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	instance->type = args->args[0];
+
+	if (!(instance->type == PHY_TYPE_USB2 ||
+	      instance->type == PHY_TYPE_USB3)) {
+		dev_err(dev, "unsupported device type: %d\n", instance->type);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return instance->phy;
+}
+
+static struct phy_ops mt65xx_u3phy_ops = {
+	.init		= mt65xx_phy_init,
+	.exit		= mt65xx_phy_exit,
+	.power_on	= mt65xx_phy_power_on,
+	.power_off	= mt65xx_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int mt65xx_u3phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *child_np;
+	struct phy_provider *provider;
+	struct resource *sif_res;
+	struct mt65xx_u3phy *u3phy;
+	struct resource res;
+	int port;
+
+	u3phy = devm_kzalloc(dev, sizeof(*u3phy), GFP_KERNEL);
+	if (!u3phy)
+		return -ENOMEM;
+
+	u3phy->nphys = of_get_child_count(np);
+	u3phy->phys = devm_kcalloc(dev, u3phy->nphys,
+				       sizeof(*u3phy->phys), GFP_KERNEL);
+	if (!u3phy->phys)
+		return -ENOMEM;
+
+	u3phy->dev = dev;
+	platform_set_drvdata(pdev, u3phy);
+
+	sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	u3phy->sif_base = devm_ioremap_resource(dev, sif_res);
+	if (IS_ERR(u3phy->sif_base)) {
+		dev_err(dev, "failed to remap sif regs\n");
+		return PTR_ERR(u3phy->sif_base);
+	}
+
+	u3phy->u3phya_ref = devm_clk_get(dev, "u3phya_ref");
+	if (IS_ERR(u3phy->u3phya_ref)) {
+		dev_err(dev, "error to get u3phya_ref\n");
+		return PTR_ERR(u3phy->u3phya_ref);
+	}
+
+	port = 0;
+	for_each_child_of_node(np, child_np) {
+		struct mt65xx_phy_instance *instance;
+		struct phy *phy;
+		int retval;
+
+		instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
+		if (!instance)
+			return -ENOMEM;
+
+		u3phy->phys[port] = instance;
+
+		phy = devm_phy_create(dev, child_np, &mt65xx_u3phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create phy\n");
+			return PTR_ERR(phy);
+		}
+
+		retval = of_address_to_resource(child_np, 0, &res);
+		if (retval) {
+			dev_err(dev, "failed to get address resource(id-%d)\n",
+				port);
+			return retval;
+		}
+
+		instance->port_base = devm_ioremap_resource(&phy->dev, &res);
+		if (IS_ERR(instance->port_base)) {
+			dev_err(dev, "failed to remap phy regs\n");
+			return PTR_ERR(instance->port_base);
+		}
+
+		instance->phy = phy;
+		instance->index = port;
+		phy_set_drvdata(phy, instance);
+		port++;
+	}
+
+	provider = devm_of_phy_provider_register(dev, mt65xx_phy_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id mt65xx_u3phy_id_table[] = {
+	{ .compatible = "mediatek,mt8173-u3phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table);
+
+static struct platform_driver mt65xx_u3phy_driver = {
+	.probe		= mt65xx_u3phy_probe,
+	.driver		= {
+		.name	= "mt65xx-u3phy",
+		.of_match_table = mt65xx_u3phy_id_table,
+	},
+};
+
+module_platform_driver(mt65xx_u3phy_driver);
+
+MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
+MODULE_DESCRIPTION("mt65xx USB PHY driver");
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-samsung-usb2.c

@@ -27,6 +27,13 @@ static int samsung_usb2_phy_power_on(struct phy *phy)
 
 	dev_dbg(drv->dev, "Request to power_on \"%s\" usb phy\n",
 		inst->cfg->label);
+
+	if (drv->vbus) {
+		ret = regulator_enable(drv->vbus);
+		if (ret)
+			goto err_regulator;
+	}
+
 	ret = clk_prepare_enable(drv->clk);
 	if (ret)
 		goto err_main_clk;
@@ -48,6 +55,9 @@ static int samsung_usb2_phy_power_on(struct phy *phy)
 err_instance_clk:
 	clk_disable_unprepare(drv->clk);
 err_main_clk:
+	if (drv->vbus)
+		regulator_disable(drv->vbus);
+err_regulator:
 	return ret;
 }
 
@@ -55,7 +65,7 @@ static int samsung_usb2_phy_power_off(struct phy *phy)
 {
 	struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy);
 	struct samsung_usb2_phy_driver *drv = inst->drv;
-	int ret;
+	int ret = 0;
 
 	dev_dbg(drv->dev, "Request to power_off \"%s\" usb phy\n",
 		inst->cfg->label);
@@ -68,7 +78,10 @@ static int samsung_usb2_phy_power_off(struct phy *phy)
 	}
 	clk_disable_unprepare(drv->ref_clk);
 	clk_disable_unprepare(drv->clk);
-	return 0;
+	if (drv->vbus)
+		ret = regulator_disable(drv->vbus);
+
+	return ret;
 }
 
 static const struct phy_ops samsung_usb2_phy_ops = {
@@ -203,6 +216,14 @@ static int samsung_usb2_phy_probe(struct platform_device *pdev)
 			return ret;
 	}
 
+	drv->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(drv->vbus)) {
+		ret = PTR_ERR(drv->vbus);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+		drv->vbus = NULL;
+	}
+
 	for (i = 0; i < drv->cfg->num_phys; i++) {
 		char *label = drv->cfg->phys[i].label;
 		struct samsung_usb2_phy_instance *p = &drv->instances[i];

drivers/phy/phy-samsung-usb2.h

@@ -17,6 +17,7 @@
 #include <linux/device.h>
 #include <linux/regmap.h>
 #include <linux/spinlock.h>
+#include <linux/regulator/consumer.h>
 
 #define KHZ 1000
 #define MHZ (KHZ * KHZ)
@@ -37,6 +38,7 @@ struct samsung_usb2_phy_driver {
 	const struct samsung_usb2_phy_config *cfg;
 	struct clk *clk;
 	struct clk *ref_clk;
+	struct regulator *vbus;
 	unsigned long ref_rate;
 	u32 ref_reg_val;
 	struct device *dev;

drivers/phy/phy-sun4i-usb.c

@@ -551,19 +551,15 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(data->base))
 		return PTR_ERR(data->base);
 
-	data->id_det_gpio = devm_gpiod_get(dev, "usb0_id_det", GPIOD_IN);
-	if (IS_ERR(data->id_det_gpio)) {
-		if (PTR_ERR(data->id_det_gpio) == -EPROBE_DEFER)
-			return -EPROBE_DEFER;
-		data->id_det_gpio = NULL;
-	}
-
-	data->vbus_det_gpio = devm_gpiod_get(dev, "usb0_vbus_det", GPIOD_IN);
-	if (IS_ERR(data->vbus_det_gpio)) {
-		if (PTR_ERR(data->vbus_det_gpio) == -EPROBE_DEFER)
-			return -EPROBE_DEFER;
-		data->vbus_det_gpio = NULL;
-	}
+	data->id_det_gpio = devm_gpiod_get_optional(dev, "usb0_id_det",
+						    GPIOD_IN);
+	if (IS_ERR(data->id_det_gpio))
+		return PTR_ERR(data->id_det_gpio);
+
+	data->vbus_det_gpio = devm_gpiod_get_optional(dev, "usb0_vbus_det",
+						      GPIOD_IN);
+	if (IS_ERR(data->vbus_det_gpio))
+		return PTR_ERR(data->vbus_det_gpio);
 
 	if (of_find_property(np, "usb0_vbus_power-supply", NULL)) {
 		data->vbus_power_supply = devm_power_supply_get_by_phandle(dev,