pinctrl: Renesas RZ/A1 pin and gpio controller

Add combined gpio and pin controller driver for Renesas RZ/A1
r7s72100 SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

drivers/pinctrl/Kconfig

@@ -174,6 +174,17 @@ config PINCTRL_ROCKCHIP
 	select GENERIC_IRQ_CHIP
 	select MFD_SYSCON
 
+config PINCTRL_RZA1
+	bool "Renesas RZ/A1 gpio and pinctrl driver"
+	depends on OF
+	depends on ARCH_R7S72100 || COMPILE_TEST
+	select GPIOLIB
+	select GENERIC_PINCTRL_GROUPS
+	select GENERIC_PINMUX_FUNCTIONS
+	select GENERIC_PINCONF
+	help
+	  This selects pinctrl driver for Renesas RZ/A1 platforms.
+
 config PINCTRL_SINGLE
 	tristate "One-register-per-pin type device tree based pinctrl driver"
 	depends on OF

drivers/pinctrl/Makefile

@@ -25,6 +25,7 @@ obj-$(CONFIG_PINCTRL_PALMAS)	+= pinctrl-palmas.o
 obj-$(CONFIG_PINCTRL_PIC32)	+= pinctrl-pic32.o
 obj-$(CONFIG_PINCTRL_PISTACHIO)	+= pinctrl-pistachio.o
 obj-$(CONFIG_PINCTRL_ROCKCHIP)	+= pinctrl-rockchip.o
+obj-$(CONFIG_PINCTRL_RZA1)	+= pinctrl-rza1.o
 obj-$(CONFIG_PINCTRL_SINGLE)	+= pinctrl-single.o
 obj-$(CONFIG_PINCTRL_SIRF)	+= sirf/
 obj-$(CONFIG_PINCTRL_SX150X)	+= pinctrl-sx150x.o

drivers/pinctrl/pinctrl-rza1.c

+/*
+ * Combined GPIO and pin controller support for Renesas RZ/A1 (r7s72100) SoC
+ *
+ * Copyright (C) 2017 Jacopo Mondi
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * This pin controller/gpio combined driver supports Renesas devices of RZ/A1
+ * family.
+ * This includes SoCs which are sub- or super- sets of this particular line,
+ * as RZ/A1H (r7s721000), RZ/A1M (r7s721010) and RZ/A1L (r7s721020).
+ */
+
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/slab.h>
+
+#include "core.h"
+#include "devicetree.h"
+#include "pinconf.h"
+#include "pinmux.h"
+
+#define DRIVER_NAME			"pinctrl-rza1"
+
+#define RZA1_P_REG			0x0000
+#define RZA1_PPR_REG			0x0200
+#define RZA1_PM_REG			0x0300
+#define RZA1_PMC_REG			0x0400
+#define RZA1_PFC_REG			0x0500
+#define RZA1_PFCE_REG			0x0600
+#define RZA1_PFCEA_REG			0x0a00
+#define RZA1_PIBC_REG			0x4000
+#define RZA1_PBDC_REG			0x4100
+#define RZA1_PIPC_REG			0x4200
+
+#define RZA1_ADDR(mem, reg, port)	((mem) + (reg) + ((port) * 4))
+
+#define RZA1_NPORTS			12
+#define RZA1_PINS_PER_PORT		16
+#define RZA1_NPINS			(RZA1_PINS_PER_PORT * RZA1_NPORTS)
+#define RZA1_PIN_ID_TO_PORT(id)		((id) / RZA1_PINS_PER_PORT)
+#define RZA1_PIN_ID_TO_PIN(id)		((id) % RZA1_PINS_PER_PORT)
+
+/*
+ * Use 16 lower bits [15:0] for pin identifier
+ * Use 16 higher bits [31:16] for pin mux function
+ */
+#define MUX_PIN_ID_MASK			GENMASK(15, 0)
+#define MUX_FUNC_MASK			GENMASK(31, 16)
+
+#define MUX_FUNC_OFFS			16
+#define MUX_FUNC(pinconf)		\
+	((pinconf & MUX_FUNC_MASK) >> MUX_FUNC_OFFS)
+#define MUX_FUNC_PFC_MASK		BIT(0)
+#define MUX_FUNC_PFCE_MASK		BIT(1)
+#define MUX_FUNC_PFCEA_MASK		BIT(2)
+
+/* Pin mux flags */
+#define MUX_FLAGS_BIDIR			BIT(0)
+#define MUX_FLAGS_SWIO_INPUT		BIT(1)
+#define MUX_FLAGS_SWIO_OUTPUT		BIT(2)
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 pinmux flags
+ */
+
+/**
+ * rza1_bidir_pin - describe a single pin that needs bidir flag applied.
+ */
+struct rza1_bidir_pin {
+	u8 pin: 4;
+	u8 func: 4;
+};
+
+/**
+ * rza1_bidir_entry - describe a list of pins that needs bidir flag applied.
+ *		      Each struct rza1_bidir_entry describes a port.
+ */
+struct rza1_bidir_entry {
+	const unsigned int npins;
+	const struct rza1_bidir_pin *pins;
+};
+
+/**
+ * rza1_swio_pin - describe a single pin that needs bidir flag applied.
+ */
+struct rza1_swio_pin {
+	u16 pin: 4;
+	u16 port: 4;
+	u16 func: 4;
+	u16 input: 1;
+};
+
+/**
+ * rza1_swio_entry - describe a list of pins that needs swio flag applied
+ */
+struct rza1_swio_entry {
+	const unsigned int npins;
+	const struct rza1_swio_pin *pins;
+};
+
+/**
+ * rza1_pinmux_conf - group together bidir and swio pinmux flag tables
+ */
+struct rza1_pinmux_conf {
+	const struct rza1_bidir_entry *bidir_entries;
+	const struct rza1_swio_entry *swio_entries;
+};
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1H (r7s72100) pinmux flags
+ */
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p1[] = {
+	{ .pin = 0, .func = 1 },
+	{ .pin = 1, .func = 1 },
+	{ .pin = 2, .func = 1 },
+	{ .pin = 3, .func = 1 },
+	{ .pin = 4, .func = 1 },
+	{ .pin = 5, .func = 1 },
+	{ .pin = 6, .func = 1 },
+	{ .pin = 7, .func = 1 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p2[] = {
+	{ .pin = 0, .func = 1 },
+	{ .pin = 1, .func = 1 },
+	{ .pin = 2, .func = 1 },
+	{ .pin = 3, .func = 1 },
+	{ .pin = 4, .func = 1 },
+	{ .pin = 0, .func = 4 },
+	{ .pin = 1, .func = 4 },
+	{ .pin = 2, .func = 4 },
+	{ .pin = 3, .func = 4 },
+	{ .pin = 5, .func = 1 },
+	{ .pin = 6, .func = 1 },
+	{ .pin = 7, .func = 1 },
+	{ .pin = 8, .func = 1 },
+	{ .pin = 9, .func = 1 },
+	{ .pin = 10, .func = 1 },
+	{ .pin = 11, .func = 1 },
+	{ .pin = 12, .func = 1 },
+	{ .pin = 13, .func = 1 },
+	{ .pin = 14, .func = 1 },
+	{ .pin = 15, .func = 1 },
+	{ .pin = 12, .func = 4 },
+	{ .pin = 13, .func = 4 },
+	{ .pin = 14, .func = 4 },
+	{ .pin = 15, .func = 4 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p3[] = {
+	{ .pin = 3, .func = 2 },
+	{ .pin = 10, .func = 7 },
+	{ .pin = 11, .func = 7 },
+	{ .pin = 13, .func = 7 },
+	{ .pin = 14, .func = 7 },
+	{ .pin = 15, .func = 7 },
+	{ .pin = 10, .func = 8 },
+	{ .pin = 11, .func = 8 },
+	{ .pin = 13, .func = 8 },
+	{ .pin = 14, .func = 8 },
+	{ .pin = 15, .func = 8 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p4[] = {
+	{ .pin = 0, .func = 8 },
+	{ .pin = 1, .func = 8 },
+	{ .pin = 2, .func = 8 },
+	{ .pin = 3, .func = 8 },
+	{ .pin = 10, .func = 3 },
+	{ .pin = 11, .func = 3 },
+	{ .pin = 13, .func = 3 },
+	{ .pin = 14, .func = 3 },
+	{ .pin = 15, .func = 3 },
+	{ .pin = 10, .func = 4 },
+	{ .pin = 11, .func = 4 },
+	{ .pin = 13, .func = 4 },
+	{ .pin = 14, .func = 4 },
+	{ .pin = 15, .func = 4 },
+	{ .pin = 12, .func = 5 },
+	{ .pin = 13, .func = 5 },
+	{ .pin = 14, .func = 5 },
+	{ .pin = 15, .func = 5 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p6[] = {
+	{ .pin = 0, .func = 1 },
+	{ .pin = 1, .func = 1 },
+	{ .pin = 2, .func = 1 },
+	{ .pin = 3, .func = 1 },
+	{ .pin = 4, .func = 1 },
+	{ .pin = 5, .func = 1 },
+	{ .pin = 6, .func = 1 },
+	{ .pin = 7, .func = 1 },
+	{ .pin = 8, .func = 1 },
+	{ .pin = 9, .func = 1 },
+	{ .pin = 10, .func = 1 },
+	{ .pin = 11, .func = 1 },
+	{ .pin = 12, .func = 1 },
+	{ .pin = 13, .func = 1 },
+	{ .pin = 14, .func = 1 },
+	{ .pin = 15, .func = 1 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p7[] = {
+	{ .pin = 13, .func = 3 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p8[] = {
+	{ .pin = 8, .func = 3 },
+	{ .pin = 9, .func = 3 },
+	{ .pin = 10, .func = 3 },
+	{ .pin = 11, .func = 3 },
+	{ .pin = 14, .func = 2 },
+	{ .pin = 15, .func = 2 },
+	{ .pin = 14, .func = 3 },
+	{ .pin = 15, .func = 3 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p9[] = {
+	{ .pin = 0, .func = 2 },
+	{ .pin = 1, .func = 2 },
+	{ .pin = 4, .func = 2 },
+	{ .pin = 5, .func = 2 },
+	{ .pin = 6, .func = 2 },
+	{ .pin = 7, .func = 2 },
+};
+
+static const struct rza1_bidir_pin rza1h_bidir_pins_p11[] = {
+	{ .pin = 6, .func = 2 },
+	{ .pin = 7, .func = 2 },
+	{ .pin = 9, .func = 2 },
+	{ .pin = 6, .func = 4 },
+	{ .pin = 7, .func = 4 },
+	{ .pin = 9, .func = 4 },
+	{ .pin = 10, .func = 2 },
+	{ .pin = 11, .func = 2 },
+	{ .pin = 10, .func = 4 },
+	{ .pin = 11, .func = 4 },
+	{ .pin = 12, .func = 4 },
+	{ .pin = 13, .func = 4 },
+	{ .pin = 14, .func = 4 },
+	{ .pin = 15, .func = 4 },
+};
+
+static const struct rza1_swio_pin rza1h_swio_pins[] = {
+	{ .port = 2, .pin = 7, .func = 4, .input = 0 },
+	{ .port = 2, .pin = 11, .func = 4, .input = 0 },
+	{ .port = 3, .pin = 7, .func = 3, .input = 0 },
+	{ .port = 3, .pin = 7, .func = 8, .input = 0 },
+	{ .port = 4, .pin = 7, .func = 5, .input = 0 },
+	{ .port = 4, .pin = 7, .func = 11, .input = 0 },
+	{ .port = 4, .pin = 15, .func = 6, .input = 0 },
+	{ .port = 5, .pin = 0, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 1, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 2, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 3, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 4, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 5, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 6, .func = 1, .input = 1 },
+	{ .port = 5, .pin = 7, .func = 1, .input = 1 },
+	{ .port = 7, .pin = 4, .func = 6, .input = 0 },
+	{ .port = 7, .pin = 11, .func = 2, .input = 0 },
+	{ .port = 8, .pin = 10, .func = 8, .input = 0 },
+	{ .port = 10, .pin = 15, .func = 2, .input = 0 },
+};
+
+static const struct rza1_bidir_entry rza1h_bidir_entries[RZA1_NPORTS] = {
+	[1] = { ARRAY_SIZE(rza1h_bidir_pins_p1), rza1h_bidir_pins_p1 },
+	[2] = { ARRAY_SIZE(rza1h_bidir_pins_p2), rza1h_bidir_pins_p2 },
+	[3] = { ARRAY_SIZE(rza1h_bidir_pins_p3), rza1h_bidir_pins_p3 },
+	[4] = { ARRAY_SIZE(rza1h_bidir_pins_p4), rza1h_bidir_pins_p4 },
+	[6] = { ARRAY_SIZE(rza1h_bidir_pins_p6), rza1h_bidir_pins_p6 },
+	[7] = { ARRAY_SIZE(rza1h_bidir_pins_p7), rza1h_bidir_pins_p7 },
+	[8] = { ARRAY_SIZE(rza1h_bidir_pins_p8), rza1h_bidir_pins_p8 },
+	[9] = { ARRAY_SIZE(rza1h_bidir_pins_p9), rza1h_bidir_pins_p9 },
+	[11] = { ARRAY_SIZE(rza1h_bidir_pins_p11), rza1h_bidir_pins_p11 },
+};
+
+static const struct rza1_swio_entry rza1h_swio_entries[] = {
+	[0] = { ARRAY_SIZE(rza1h_swio_pins), rza1h_swio_pins },
+};
+
+/* RZ/A1H (r7s72100x) pinmux flags table */
+static const struct rza1_pinmux_conf rza1h_pmx_conf = {
+	.bidir_entries	= rza1h_bidir_entries,
+	.swio_entries	= rza1h_swio_entries,
+};
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 types
+ */
+/**
+ * rza1_mux_conf - describes a pin multiplexing operation
+ *
+ * @id: the pin identifier from 0 to RZA1_NPINS
+ * @port: the port where pin sits on
+ * @pin: pin id
+ * @mux_func: alternate function id number
+ * @mux_flags: alternate function flags
+ * @value: output value to set the pin to
+ */
+struct rza1_mux_conf {
+	u16 id;
+	u8 port;
+	u8 pin;
+	u8 mux_func;
+	u8 mux_flags;
+	u8 value;
+};
+
+/**
+ * rza1_port - describes a pin port
+ *
+ * This is mostly useful to lock register writes per-bank and not globally.
+ *
+ * @lock: protect access to HW registers
+ * @id: port number
+ * @base: logical address base
+ * @pins: pins sitting on this port
+ */
+struct rza1_port {
+	spinlock_t lock;
+	unsigned int id;
+	void __iomem *base;
+	struct pinctrl_pin_desc *pins;
+};
+
+/**
+ * rza1_pinctrl - RZ pincontroller device
+ *
+ * @dev: parent device structure
+ * @mutex: protect [pinctrl|pinmux]_generic functions
+ * @base: logical address base
+ * @nports: number of pin controller ports
+ * @ports: pin controller banks
+ * @pins: pin array for pinctrl core
+ * @desc: pincontroller desc for pinctrl core
+ * @pctl: pinctrl device
+ * @data: device specific data
+ */
+struct rza1_pinctrl {
+	struct device *dev;
+
+	struct mutex mutex;
+
+	void __iomem *base;
+
+	unsigned int nport;
+	struct rza1_port *ports;
+
+	struct pinctrl_pin_desc *pins;
+	struct pinctrl_desc desc;
+	struct pinctrl_dev *pctl;
+
+	const void *data;
+};
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 pinmux flags
+ */
+static inline bool rza1_pinmux_get_bidir(unsigned int port,
+					 unsigned int pin,
+					 unsigned int func,
+					 const struct rza1_bidir_entry *table)
+{
+	const struct rza1_bidir_entry *entry = &table[port];
+	const struct rza1_bidir_pin *bidir_pin;
+	unsigned int i;
+
+	for (i = 0; i < entry->npins; ++i) {
+		bidir_pin = &entry->pins[i];
+		if (bidir_pin->pin == pin && bidir_pin->func == func)
+			return true;
+	}
+
+	return false;
+}
+
+static inline int rza1_pinmux_get_swio(unsigned int port,
+				       unsigned int pin,
+				       unsigned int func,
+				       const struct rza1_swio_entry *table)
+{
+	const struct rza1_swio_pin *swio_pin;
+	unsigned int i;
+
+
+	for (i = 0; i < table->npins; ++i) {
+		swio_pin = &table->pins[i];
+		if (swio_pin->port == port && swio_pin->pin == pin &&
+		    swio_pin->func == func)
+			return swio_pin->input;
+	}
+
+	return -ENOENT;
+}
+
+/**
+ * rza1_pinmux_get_flags() - return pinmux flags associated to a pin
+ */
+static unsigned int rza1_pinmux_get_flags(unsigned int port, unsigned int pin,
+					  unsigned int func,
+					  struct rza1_pinctrl *rza1_pctl)
+
+{
+	const struct rza1_pinmux_conf *pmx_conf = rza1_pctl->data;
+	const struct rza1_bidir_entry *bidir_entries = pmx_conf->bidir_entries;
+	const struct rza1_swio_entry *swio_entries = pmx_conf->swio_entries;
+	unsigned int pmx_flags = 0;
+	int ret;
+
+	if (rza1_pinmux_get_bidir(port, pin, func, bidir_entries))
+		pmx_flags |= MUX_FLAGS_BIDIR;
+
+	ret = rza1_pinmux_get_swio(port, pin, func, swio_entries);
+	if (ret == 0)
+		pmx_flags |= MUX_FLAGS_SWIO_OUTPUT;
+	else if (ret > 0)
+		pmx_flags |= MUX_FLAGS_SWIO_INPUT;
+
+	return pmx_flags;
+}
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 SoC operations
+ */
+
+/**
+ * rza1_set_bit() - un-locked set/clear a single bit in pin configuration
+ *		    registers
+ */
+static inline void rza1_set_bit(struct rza1_port *port, unsigned int reg,
+				unsigned int bit, bool set)
+{
+	void __iomem *mem = RZA1_ADDR(port->base, reg, port->id);
+	u16 val = ioread16(mem);
+
+	if (set)
+		val |= BIT(bit);
+	else
+		val &= ~BIT(bit);
+
+	iowrite16(val, mem);
+}
+
+static inline unsigned int rza1_get_bit(struct rza1_port *port,
+					unsigned int reg, unsigned int bit)
+{
+	void __iomem *mem = RZA1_ADDR(port->base, reg, port->id);
+
+	return ioread16(mem) & BIT(bit);
+}
+
+/**
+ * rza1_pin_reset() - reset a pin to default initial state
+ *
+ * Reset pin state disabling input buffer and bi-directional control,
+ * and configure it as input port.
+ * Note that pin is now configured with direction as input but with input
+ * buffer disabled. This implies the pin value cannot be read in this state.
+ *
+ * @port: port where pin sits on
+ * @pin: pin offset
+ */
+static void rza1_pin_reset(struct rza1_port *port, unsigned int pin)
+{
+	unsigned long irqflags;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+	rza1_set_bit(port, RZA1_PIBC_REG, pin, 0);
+	rza1_set_bit(port, RZA1_PBDC_REG, pin, 0);
+
+	rza1_set_bit(port, RZA1_PM_REG, pin, 1);
+	rza1_set_bit(port, RZA1_PMC_REG, pin, 0);
+	rza1_set_bit(port, RZA1_PIPC_REG, pin, 0);
+	spin_unlock_irqrestore(&port->lock, irqflags);
+}
+
+static inline int rza1_pin_get_direction(struct rza1_port *port,
+					 unsigned int pin)
+{
+	unsigned long irqflags;
+	int input;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+	input = rza1_get_bit(port, RZA1_PM_REG, pin);
+	spin_unlock_irqrestore(&port->lock, irqflags);
+
+	return !!input;
+}
+
+/**
+ * rza1_pin_set_direction() - set I/O direction on a pin in port mode
+ *
+ * When running in output port mode keep PBDC enabled to allow reading the
+ * pin value from PPR.
+ *
+ * @port: port where pin sits on
+ * @pin: pin offset
+ * @input: input enable/disable flag
+ */
+static inline void rza1_pin_set_direction(struct rza1_port *port,
+					  unsigned int pin, bool input)
+{
+	unsigned long irqflags;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+
+	rza1_set_bit(port, RZA1_PIBC_REG, pin, 1);
+	if (input) {
+		rza1_set_bit(port, RZA1_PM_REG, pin, 1);
+		rza1_set_bit(port, RZA1_PBDC_REG, pin, 0);
+	} else {
+		rza1_set_bit(port, RZA1_PM_REG, pin, 0);
+		rza1_set_bit(port, RZA1_PBDC_REG, pin, 1);
+	}
+
+	spin_unlock_irqrestore(&port->lock, irqflags);
+}
+
+static inline void rza1_pin_set(struct rza1_port *port, unsigned int pin,
+				unsigned int value)
+{
+	unsigned long irqflags;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+	rza1_set_bit(port, RZA1_P_REG, pin, !!value);
+	spin_unlock_irqrestore(&port->lock, irqflags);
+}
+
+static inline int rza1_pin_get(struct rza1_port *port, unsigned int pin)
+{
+	unsigned long irqflags;
+	int val;
+
+	spin_lock_irqsave(&port->lock, irqflags);
+	val = rza1_get_bit(port, RZA1_PPR_REG, pin);
+	spin_unlock_irqrestore(&port->lock, irqflags);
+
+	return val;
+}
+
+/**
+ * rza1_pin_mux_single() - configure pin multiplexing on a single pin
+ *
+ * @pinctrl: RZ/A1 pin controller device
+ * @mux_conf: pin multiplexing descriptor
+ */
+static int rza1_pin_mux_single(struct rza1_pinctrl *rza1_pctl,
+			       struct rza1_mux_conf *mux_conf)
+{
+	struct rza1_port *port = &rza1_pctl->ports[mux_conf->port];
+	unsigned int pin = mux_conf->pin;
+	u8 mux_func = mux_conf->mux_func;
+	u8 mux_flags = mux_conf->mux_flags;
+	u8 mux_flags_from_table;
+
+	rza1_pin_reset(port, pin);
+
+	/* SWIO pinmux flags coming from DT are high precedence */
+	mux_flags_from_table = rza1_pinmux_get_flags(port->id, pin, mux_func,
+						     rza1_pctl);
+	if (mux_flags)
+		mux_flags |= (mux_flags_from_table & MUX_FLAGS_BIDIR);
+	else
+		mux_flags = mux_flags_from_table;
+
+	if (mux_flags & MUX_FLAGS_BIDIR)
+		rza1_set_bit(port, RZA1_PBDC_REG, pin, 1);
+
+	/*
+	 * Enable alternate function mode and select it.
+	 *
+	 * Be careful here: the pin mux sub-nodes in device tree
+	 * enumerate alternate functions from 1 to 8;
+	 * subtract 1 before using macros to match registers configuration
+	 * which expects numbers from 0 to 7 instead.
+	 *
+	 * ----------------------------------------------------
+	 * Alternate mode selection table:
+	 *
+	 * PMC	PFC	PFCE	PFCAE	(mux_func - 1)
+	 * 1	0	0	0	0
+	 * 1	1	0	0	1
+	 * 1	0	1	0	2
+	 * 1	1	1	0	3
+	 * 1	0	0	1	4
+	 * 1	1	0	1	5
+	 * 1	0	1	1	6
+	 * 1	1	1	1	7
+	 * ----------------------------------------------------
+	 */
+	mux_func -= 1;
+	rza1_set_bit(port, RZA1_PFC_REG, pin, mux_func & MUX_FUNC_PFC_MASK);
+	rza1_set_bit(port, RZA1_PFCE_REG, pin, mux_func & MUX_FUNC_PFCE_MASK);
+	rza1_set_bit(port, RZA1_PFCEA_REG, pin, mux_func & MUX_FUNC_PFCEA_MASK);
+
+	/*
+	 * All alternate functions except a few need PIPCn = 1.
+	 * If PIPCn has to stay disabled (SW IO mode), configure PMn according
+	 * to I/O direction specified by pin configuration -after- PMC has been
+	 * set to one.
+	 */
+	if (mux_flags & (MUX_FLAGS_SWIO_INPUT | MUX_FLAGS_SWIO_OUTPUT))
+		rza1_set_bit(port, RZA1_PM_REG, pin,
+			     mux_flags & MUX_FLAGS_SWIO_INPUT);
+	else
+		rza1_set_bit(port, RZA1_PIPC_REG, pin, 1);
+
+	rza1_set_bit(port, RZA1_PMC_REG, pin, 1);
+
+	return 0;
+}
+
+/* ----------------------------------------------------------------------------
+ * gpio operations
+ */
+
+/**
+ * rza1_gpio_request() - configure pin in port mode
+ *
+ * Configure a pin as gpio (port mode).
+ * After reset, the pin is in input mode with input buffer disabled.
+ * To use the pin as input or output, set_direction shall be called first
+ *
+ * @chip: gpio chip where the gpio sits on
+ * @gpio: gpio offset
+ */
+static int rza1_gpio_request(struct gpio_chip *chip, unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	rza1_pin_reset(port, gpio);
+
+	return 0;
+}
+
+/**
+ * rza1_gpio_disable_free() - reset a pin
+ *
+ * Surprisingly, disable_free a gpio, is equivalent to request it.
+ * Reset pin to port mode, with input buffer disabled. This overwrites all
+ * port direction settings applied with set_direction
+ *
+ * @chip: gpio chip where the gpio sits on
+ * @gpio: gpio offset
+ */
+static void rza1_gpio_free(struct gpio_chip *chip, unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	rza1_pin_reset(port, gpio);
+}
+
+static int rza1_gpio_get_direction(struct gpio_chip *chip, unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	return rza1_pin_get_direction(port, gpio);
+}
+
+static int rza1_gpio_direction_input(struct gpio_chip *chip,
+				     unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	rza1_pin_set_direction(port, gpio, true);
+
+	return 0;
+}
+
+static int rza1_gpio_direction_output(struct gpio_chip *chip,
+				      unsigned int gpio,
+				      int value)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	/* Set value before driving pin direction */
+	rza1_pin_set(port, gpio, value);
+	rza1_pin_set_direction(port, gpio, false);
+
+	return 0;
+}
+
+/**
+ * rza1_gpio_get() - read a gpio pin value
+ *
+ * Read gpio pin value through PPR register.
+ * Requires bi-directional mode to work when reading the value of a pin
+ * in output mode
+ *
+ * @chip: gpio chip where the gpio sits on
+ * @gpio: gpio offset
+ */
+static int rza1_gpio_get(struct gpio_chip *chip, unsigned int gpio)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	return rza1_pin_get(port, gpio);
+}
+
+static void rza1_gpio_set(struct gpio_chip *chip, unsigned int gpio,
+			  int value)
+{
+	struct rza1_port *port = gpiochip_get_data(chip);
+
+	rza1_pin_set(port, gpio, value);
+}
+
+struct gpio_chip rza1_gpiochip_template = {
+	.request		= rza1_gpio_request,
+	.free			= rza1_gpio_free,
+	.get_direction		= rza1_gpio_get_direction,
+	.direction_input	= rza1_gpio_direction_input,
+	.direction_output	= rza1_gpio_direction_output,
+	.get			= rza1_gpio_get,
+	.set			= rza1_gpio_set,
+};
+/* ----------------------------------------------------------------------------
+ * pinctrl operations
+ */
+
+/**
+ * rza1_dt_node_pin_count() - Count number of pins in a dt node or in all its
+ *			      children sub-nodes
+ *
+ * @np: device tree node to parse
+ */
+static int rza1_dt_node_pin_count(struct device_node *np)
+{
+	struct device_node *child;
+	struct property *of_pins;
+	unsigned int npins;
+
+	of_pins = of_find_property(np, "pinmux", NULL);
+	if (of_pins)
+		return of_pins->length / sizeof(u32);
+
+	npins = 0;
+	for_each_child_of_node(np, child) {
+		of_pins = of_find_property(child, "pinmux", NULL);
+		if (!of_pins)
+			return -EINVAL;
+
+		npins += of_pins->length / sizeof(u32);
+	}
+
+	return npins;
+}
+
+/**
+ * rza1_parse_pmx_function() - parse a pin mux sub-node
+ *
+ * @rza1_pctl: RZ/A1 pin controller device
+ * @np: of pmx sub-node
+ * @mux_confs: array of pin mux configurations to fill with parsed info
+ * @grpins: array of pin ids to mux
+ */
+static int rza1_parse_pinmux_node(struct rza1_pinctrl *rza1_pctl,
+				  struct device_node *np,
+				  struct rza1_mux_conf *mux_confs,
+				  unsigned int *grpins)
+{
+	struct pinctrl_dev *pctldev = rza1_pctl->pctl;
+	char const *prop_name = "pinmux";
+	unsigned long *pin_configs;
+	unsigned int npin_configs;
+	struct property *of_pins;
+	unsigned int npins;
+	u8 pinmux_flags;
+	unsigned int i;
+	int ret;
+
+	of_pins = of_find_property(np, prop_name, NULL);
+	if (!of_pins) {
+		dev_dbg(rza1_pctl->dev, "Missing %s property\n", prop_name);
+		return -ENOENT;
+	}
+	npins = of_pins->length / sizeof(u32);
+
+	/*
+	 * Collect pin configuration properties: they apply to all pins in
+	 * this sub-node
+	 */
+	ret = pinconf_generic_parse_dt_config(np, pctldev, &pin_configs,
+					      &npin_configs);
+	if (ret) {
+		dev_err(rza1_pctl->dev,
+			"Unable to parse pin configuration options for %s\n",
+			np->name);
+		return ret;
+	}
+
+	/*
+	 * Create a mask with pinmux flags from pin configuration;
+	 * very few pins (TIOC[0-4][A|B|C|D] require SWIO direction
+	 * specified in device tree.
+	 */
+	pinmux_flags = 0;
+	for (i = 0; i < npin_configs && pinmux_flags == 0; i++)
+		switch (pinconf_to_config_param(pin_configs[i])) {
+		case PIN_CONFIG_INPUT_ENABLE:
+			pinmux_flags |= MUX_FLAGS_SWIO_INPUT;
+			break;
+		case PIN_CONFIG_OUTPUT:
+			pinmux_flags |= MUX_FLAGS_SWIO_OUTPUT;
+		default:
+			break;
+
+		}
+
+	kfree(pin_configs);
+
+	/* Collect pin positions and their mux settings. */
+	for (i = 0; i < npins; ++i) {
+		u32 of_pinconf;
+		struct rza1_mux_conf *mux_conf = &mux_confs[i];
+
+		ret = of_property_read_u32_index(np, prop_name, i, &of_pinconf);
+		if (ret)
+			return ret;
+
+		mux_conf->id		= of_pinconf & MUX_PIN_ID_MASK;
+		mux_conf->port		= RZA1_PIN_ID_TO_PORT(mux_conf->id);
+		mux_conf->pin		= RZA1_PIN_ID_TO_PIN(mux_conf->id);
+		mux_conf->mux_func	= MUX_FUNC(of_pinconf);
+		mux_conf->mux_flags	= pinmux_flags;
+
+		if (mux_conf->port >= RZA1_NPORTS ||
+		    mux_conf->pin >= RZA1_PINS_PER_PORT) {
+			dev_err(rza1_pctl->dev,
+				"Wrong port %u pin %u for %s property\n",
+				mux_conf->port, mux_conf->pin, prop_name);
+			return -EINVAL;
+		}
+
+		grpins[i] = mux_conf->id;
+	}
+
+	return npins;
+}
+
+/**
+ * rza1_dt_node_to_map() - map a pin mux node to a function/group
+ *
+ * Parse and register a pin mux function.
+ *
+ * @pctldev: pin controller device
+ * @np: device tree node to parse
+ * @map: pointer to pin map (output)
+ * @num_maps: number of collected maps (output)
+ */
+static int rza1_dt_node_to_map(struct pinctrl_dev *pctldev,
+			       struct device_node *np,
+			       struct pinctrl_map **map,
+			       unsigned int *num_maps)
+{
+	struct rza1_pinctrl *rza1_pctl = pinctrl_dev_get_drvdata(pctldev);
+	struct rza1_mux_conf *mux_confs, *mux_conf;
+	unsigned int *grpins, *grpin;
+	struct device_node *child;
+	const char *grpname;
+	const char **fngrps;
+	int ret, npins;
+
+	npins = rza1_dt_node_pin_count(np);
+	if (npins < 0) {
+		dev_err(rza1_pctl->dev, "invalid pinmux node structure\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Functions are made of 1 group only;
+	 * in fact, functions and groups are identical for this pin controller
+	 * except that functions carry an array of per-pin mux configuration
+	 * settings.
+	 */
+	mux_confs = devm_kcalloc(rza1_pctl->dev, npins, sizeof(*mux_confs),
+				 GFP_KERNEL);
+	grpins = devm_kcalloc(rza1_pctl->dev, npins, sizeof(*grpins),
+			      GFP_KERNEL);
+	fngrps = devm_kzalloc(rza1_pctl->dev, sizeof(*fngrps), GFP_KERNEL);
+
+	if (!mux_confs || !grpins || !fngrps)
+		return -ENOMEM;
+
+	/*
+	 * Parse the pinmux node.
+	 * If the node does not contain "pinmux" property (-ENOENT)
+	 * that property shall be specified in all its children sub-nodes.
+	 */
+	mux_conf = &mux_confs[0];
+	grpin = &grpins[0];
+
+	ret = rza1_parse_pinmux_node(rza1_pctl, np, mux_conf, grpin);
+	if (ret == -ENOENT)
+		for_each_child_of_node(np, child) {
+			ret = rza1_parse_pinmux_node(rza1_pctl, child, mux_conf,
+						     grpin);
+			if (ret < 0)
+				return ret;
+
+			grpin += ret;
+			mux_conf += ret;
+		}
+	else if (ret < 0)
+		return ret;
+
+	/* Register pin group and function name to pinctrl_generic */
+	grpname	= np->name;
+	fngrps[0] = grpname;
+
+	mutex_lock(&rza1_pctl->mutex);
+	ret = pinctrl_generic_add_group(pctldev, grpname, grpins, npins,
+					NULL);
+	if (ret) {
+		mutex_unlock(&rza1_pctl->mutex);
+		return ret;
+	}
+
+	ret = pinmux_generic_add_function(pctldev, grpname, fngrps, 1,
+					  mux_confs);
+	if (ret)
+		goto remove_group;
+	mutex_unlock(&rza1_pctl->mutex);
+
+	dev_info(rza1_pctl->dev, "Parsed function and group %s with %d pins\n",
+				 grpname, npins);
+
+	/* Create map where to retrieve function and mux settings from */
+	*num_maps = 0;
+	*map = kzalloc(sizeof(**map), GFP_KERNEL);
+	if (!*map) {
+		ret = -ENOMEM;
+		goto remove_function;
+	}
+
+	(*map)->type = PIN_MAP_TYPE_MUX_GROUP;
+	(*map)->data.mux.group = np->name;
+	(*map)->data.mux.function = np->name;
+	*num_maps = 1;
+
+	return 0;
+
+remove_function:
+	mutex_lock(&rza1_pctl->mutex);
+	pinmux_generic_remove_last_function(pctldev);
+
+remove_group:
+	pinctrl_generic_remove_last_group(pctldev);
+	mutex_unlock(&rza1_pctl->mutex);
+
+	dev_info(rza1_pctl->dev, "Unable to parse function and group %s\n",
+				 grpname);
+
+	return ret;
+}
+
+static void rza1_dt_free_map(struct pinctrl_dev *pctldev,
+			     struct pinctrl_map *map, unsigned int num_maps)
+{
+	kfree(map);
+}
+
+static const struct pinctrl_ops rza1_pinctrl_ops = {
+	.get_groups_count	= pinctrl_generic_get_group_count,
+	.get_group_name		= pinctrl_generic_get_group_name,
+	.get_group_pins		= pinctrl_generic_get_group_pins,
+	.dt_node_to_map		= rza1_dt_node_to_map,
+	.dt_free_map		= rza1_dt_free_map,
+};
+
+/* ----------------------------------------------------------------------------
+ * pinmux operations
+ */
+
+/**
+ * rza1_set_mux() - retrieve pins from a group and apply their mux settings
+ *
+ * @pctldev: pin controller device
+ * @selector: function selector
+ * @group: group selector
+ */
+static int rza1_set_mux(struct pinctrl_dev *pctldev, unsigned int selector,
+			   unsigned int group)
+{
+	struct rza1_pinctrl *rza1_pctl = pinctrl_dev_get_drvdata(pctldev);
+	struct rza1_mux_conf *mux_confs;
+	struct function_desc *func;
+	struct group_desc *grp;
+	int i;
+
+	grp = pinctrl_generic_get_group(pctldev, group);
+	if (!grp)
+		return -EINVAL;
+
+	func = pinmux_generic_get_function(pctldev, selector);
+	if (!func)
+		return -EINVAL;
+
+	mux_confs = (struct rza1_mux_conf *)func->data;
+	for (i = 0; i < grp->num_pins; ++i) {
+		int ret;
+
+		ret = rza1_pin_mux_single(rza1_pctl, &mux_confs[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+struct pinmux_ops rza1_pinmux_ops = {
+	.get_functions_count	= pinmux_generic_get_function_count,
+	.get_function_name	= pinmux_generic_get_function_name,
+	.get_function_groups	= pinmux_generic_get_function_groups,
+	.set_mux		= rza1_set_mux,
+	.strict			= true,
+};
+
+/* ----------------------------------------------------------------------------
+ * RZ/A1 pin controller driver operations
+ */
+
+static unsigned int rza1_count_gpio_chips(struct device_node *np)
+{
+	struct device_node *child;
+	unsigned int count = 0;
+
+	for_each_child_of_node(np, child) {
+		if (!of_property_read_bool(child, "gpio-controller"))
+			continue;
+
+		count++;
+	}
+
+	return count;
+}
+
+/**
+ * rza1_parse_gpiochip() - parse and register a gpio chip and pin range
+ *
+ * The gpio controller subnode shall provide a "gpio-ranges" list property as
+ * defined by gpio device tree binding documentation.
+ *
+ * @rza1_pctl: RZ/A1 pin controller device
+ * @np: of gpio-controller node
+ * @chip: gpio chip to register to gpiolib
+ * @range: pin range to register to pinctrl core
+ */
+static int rza1_parse_gpiochip(struct rza1_pinctrl *rza1_pctl,
+			       struct device_node *np,
+			       struct gpio_chip *chip,
+			       struct pinctrl_gpio_range *range)
+{
+	const char *list_name = "gpio-ranges";
+	struct of_phandle_args of_args;
+	unsigned int gpioport;
+	u32 pinctrl_base;
+	int ret;
+
+	ret = of_parse_phandle_with_fixed_args(np, list_name, 3, 0, &of_args);
+	if (ret) {
+		dev_err(rza1_pctl->dev, "Unable to parse %s list property\n",
+			list_name);
+		return ret;
+	}
+
+	/*
+	 * Find out on which port this gpio-chip maps to by inspecting the
+	 * second argument of the "gpio-ranges" property.
+	 */
+	pinctrl_base = of_args.args[1];
+	gpioport = RZA1_PIN_ID_TO_PORT(pinctrl_base);
+	if (gpioport > RZA1_NPORTS) {
+		dev_err(rza1_pctl->dev,
+			"Invalid values in property %s\n", list_name);
+		return -EINVAL;
+	}
+
+	*chip		= rza1_gpiochip_template;
+	chip->base	= -1;
+	chip->label	= devm_kasprintf(rza1_pctl->dev, GFP_KERNEL, "%s-%u",
+					 np->name, gpioport);
+	chip->ngpio	= of_args.args[2];
+	chip->of_node	= np;
+	chip->parent	= rza1_pctl->dev;
+
+	range->id	= gpioport;
+	range->name	= chip->label;
+	range->pin_base	= range->base = pinctrl_base;
+	range->npins	= of_args.args[2];
+	range->gc	= chip;
+
+	ret = devm_gpiochip_add_data(rza1_pctl->dev, chip,
+				     &rza1_pctl->ports[gpioport]);
+	if (ret)
+		return ret;
+
+	pinctrl_add_gpio_range(rza1_pctl->pctl, range);
+
+	dev_info(rza1_pctl->dev, "Parsed gpiochip %s with %d pins\n",
+		 chip->label, chip->ngpio);
+
+	return 0;
+}
+
+/**
+ * rza1_gpio_register() - parse DT to collect gpio-chips and gpio-ranges
+ *
+ * @rza1_pctl: RZ/A1 pin controller device
+ */
+static int rza1_gpio_register(struct rza1_pinctrl *rza1_pctl)
+{
+	struct device_node *np = rza1_pctl->dev->of_node;
+	struct pinctrl_gpio_range *gpio_ranges;
+	struct gpio_chip *gpio_chips;
+	struct device_node *child;
+	unsigned int ngpiochips;
+	unsigned int i;
+	int ret;
+
+	ngpiochips = rza1_count_gpio_chips(np);
+	if (ngpiochips == 0) {
+		dev_dbg(rza1_pctl->dev, "No gpiochip registered\n");
+		return 0;
+	}
+
+	gpio_chips = devm_kcalloc(rza1_pctl->dev, ngpiochips,
+				  sizeof(*gpio_chips), GFP_KERNEL);
+	gpio_ranges = devm_kcalloc(rza1_pctl->dev, ngpiochips,
+				   sizeof(*gpio_ranges), GFP_KERNEL);
+	if (!gpio_chips || !gpio_ranges)
+		return -ENOMEM;
+
+	i = 0;
+	for_each_child_of_node(np, child) {
+		if (!of_property_read_bool(child, "gpio-controller"))
+			continue;
+
+		ret = rza1_parse_gpiochip(rza1_pctl, child, &gpio_chips[i],
+					  &gpio_ranges[i]);
+		if (ret)
+			goto gpiochip_remove;
+
+		++i;
+	}
+
+	dev_info(rza1_pctl->dev, "Registered %u gpio controllers\n", i);
+
+	return 0;
+
+gpiochip_remove:
+	for (; i > 0; i--)
+		devm_gpiochip_remove(rza1_pctl->dev, &gpio_chips[i - 1]);
+
+	return ret;
+}
+
+/**
+ * rza1_pinctrl_register() - Enumerate pins, ports and gpiochips; register
+ *			     them to pinctrl and gpio cores.
+ *
+ * @rza1_pctl: RZ/A1 pin controller device
+ */
+static int rza1_pinctrl_register(struct rza1_pinctrl *rza1_pctl)
+{
+	struct pinctrl_pin_desc *pins;
+	struct rza1_port *ports;
+	unsigned int i;
+	int ret;
+
+	pins = devm_kcalloc(rza1_pctl->dev, RZA1_NPINS, sizeof(*pins),
+			    GFP_KERNEL);
+	ports = devm_kcalloc(rza1_pctl->dev, RZA1_NPORTS, sizeof(*ports),
+			     GFP_KERNEL);
+	if (!pins || !ports)
+		return -ENOMEM;
+
+	rza1_pctl->pins		= pins;
+	rza1_pctl->desc.pins	= pins;
+	rza1_pctl->desc.npins	= RZA1_NPINS;
+	rza1_pctl->ports	= ports;
+
+	for (i = 0; i < RZA1_NPINS; ++i) {
+		unsigned int pin = RZA1_PIN_ID_TO_PIN(i);
+		unsigned int port = RZA1_PIN_ID_TO_PORT(i);
+
+		pins[i].number = i;
+		pins[i].name = devm_kasprintf(rza1_pctl->dev, GFP_KERNEL,
+					      "P%u-%u", port, pin);
+
+		if (i % RZA1_PINS_PER_PORT == 0) {
+			/*
+			 * Setup ports;
+			 * they provide per-port lock and logical base address.
+			 */
+			unsigned int port_id = RZA1_PIN_ID_TO_PORT(i);
+
+			ports[port_id].id	= port_id;
+			ports[port_id].base	= rza1_pctl->base;
+			ports[port_id].pins	= &pins[i];
+			spin_lock_init(&ports[port_id].lock);
+		}
+	}
+
+	ret = devm_pinctrl_register_and_init(rza1_pctl->dev, &rza1_pctl->desc,
+					     rza1_pctl, &rza1_pctl->pctl);
+	if (ret) {
+		dev_err(rza1_pctl->dev,
+			"RZ/A1 pin controller registration failed\n");
+		return ret;
+	}
+
+	ret = pinctrl_enable(rza1_pctl->pctl);
+	if (ret) {
+		dev_err(rza1_pctl->dev,
+			"RZ/A1 pin controller failed to start\n");
+		return ret;
+	}
+
+	ret = rza1_gpio_register(rza1_pctl);
+	if (ret) {
+		dev_err(rza1_pctl->dev, "RZ/A1 GPIO registration failed\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rza1_pinctrl_probe(struct platform_device *pdev)
+{
+	struct rza1_pinctrl *rza1_pctl;
+	struct resource *res;
+	int ret;
+
+	rza1_pctl = devm_kzalloc(&pdev->dev, sizeof(*rza1_pctl), GFP_KERNEL);
+	if (!rza1_pctl)
+		return -ENOMEM;
+
+	rza1_pctl->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (ret)
+		return -ENODEV;
+
+	rza1_pctl->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rza1_pctl->base))
+		return PTR_ERR(rza1_pctl->base);
+
+	mutex_init(&rza1_pctl->mutex);
+
+	platform_set_drvdata(pdev, rza1_pctl);
+
+	rza1_pctl->desc.name	= DRIVER_NAME;
+	rza1_pctl->desc.pctlops	= &rza1_pinctrl_ops;
+	rza1_pctl->desc.pmxops	= &rza1_pinmux_ops;
+	rza1_pctl->desc.owner	= THIS_MODULE;
+	rza1_pctl->data		= of_device_get_match_data(&pdev->dev);
+
+	ret = rza1_pinctrl_register(rza1_pctl);
+	if (ret)
+		return ret;
+
+	dev_info(&pdev->dev,
+		 "RZ/A1 pin controller and gpio successfully registered\n");
+
+	return 0;
+}
+
+static const struct of_device_id rza1_pinctrl_of_match[] = {
+	{
+		.compatible	= "renesas,r7s72100-ports",
+		.data		= &rza1h_pmx_conf,
+	},
+	{ }
+};
+
+static struct platform_driver rza1_pinctrl_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = rza1_pinctrl_of_match,
+	},
+	.probe = rza1_pinctrl_probe,
+};
+
+static int __init rza1_pinctrl_init(void)
+{
+	return platform_driver_register(&rza1_pinctrl_driver);
+}
+core_initcall(rza1_pinctrl_init);
+
+MODULE_AUTHOR("Jacopo Mondi <jacopo+renesas@jmondi.org");
+MODULE_DESCRIPTION("Pin and gpio controller driver for Reneas RZ/A1 SoC");
+MODULE_LICENSE("GPL v2");