Merge branch 'for-5.8/dt-bindings' into for-5.8/media

Documentation/devicetree/bindings/cpufreq/nvidia,tegra20-cpufreq.txt

+Binding for NVIDIA Tegra20 CPUFreq
+==================================
+
+Required properties:
+- clocks: Must contain an entry for the CPU clock.
+  See ../clocks/clock-bindings.txt for details.
+- operating-points-v2: See ../bindings/opp/opp.txt for details.
+- #cooling-cells: Should be 2. See ../thermal/thermal.txt for details.
+
+For each opp entry in 'operating-points-v2' table:
+- opp-supported-hw: Two bitfields indicating:
+	On Tegra20:
+	1. CPU process ID mask
+	2. SoC speedo ID mask
+
+	On Tegra30:
+	1. CPU process ID mask
+	2. CPU speedo ID mask
+
+	A bitwise AND is performed against these values and if any bit
+	matches, the OPP gets enabled.
+
+- opp-microvolt: CPU voltage triplet.
+
+Optional properties:
+- cpu-supply: Phandle to the CPU power supply.
+
+Example:
+	regulators {
+		cpu_reg: regulator0 {
+			regulator-name = "vdd_cpu";
+		};
+	};
+
+	cpu0_opp_table: opp_table0 {
+		compatible = "operating-points-v2";
+
+		opp@456000000 {
+			clock-latency-ns = <125000>;
+			opp-microvolt = <825000 825000 1125000>;
+			opp-supported-hw = <0x03 0x0001>;
+			opp-hz = /bits/ 64 <456000000>;
+		};
+
+		...
+	};
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			clocks = <&tegra_car TEGRA20_CLK_CCLK>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			cpu-supply = <&cpu_reg>;
+			#cooling-cells = <2>;
+		};
+	};

Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt

@@ -40,14 +40,30 @@ of the following host1x client modules:
 
   Required properties:
   - compatible: "nvidia,tegra<chip>-vi"
-  - reg: Physical base address and length of the controller's registers.
+  - reg: Physical base address and length of the controller registers.
   - interrupts: The interrupt outputs from the controller.
-  - clocks: Must contain one entry, for the module clock.
+  - clocks: clocks: Must contain one entry, for the module clock.
     See ../clocks/clock-bindings.txt for details.
-  - resets: Must contain an entry for each entry in reset-names.
-    See ../reset/reset.txt for details.
-  - reset-names: Must include the following entries:
-    - vi
+  - Tegra20/Tegra30/Tegra114/Tegra124:
+    - resets: Must contain an entry for each entry in reset-names.
+      See ../reset/reset.txt for details.
+    - reset-names: Must include the following entries:
+      - vi
+  - Tegra210:
+    - power-domains: Must include venc powergate node as vi is in VE partition.
+  - Tegra210 has CSI part of VI sharing same host interface and register space.
+    So, VI device node should have CSI child node.
+
+    - csi: mipi csi interface to vi
+
+      Required properties:
+      - compatible: "nvidia,tegra210-csi"
+      - reg: Physical base address offset to parent and length of the controller
+        registers.
+      - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks.
+        See ../clocks/clock-bindings.txt for details.
+      - power-domains: Must include sor powergate node as csicil is in
+        SOR partition.
 
 - epp: encoder pre-processor
 
@@ -309,13 +325,44 @@ Example:
 			reset-names = "mpe";
 		};
 
-		vi {
-			compatible = "nvidia,tegra20-vi";
-			reg = <0x54080000 0x00040000>;
-			interrupts = <0 69 0x04>;
-			clocks = <&tegra_car TEGRA20_CLK_VI>;
-			resets = <&tegra_car 100>;
-			reset-names = "vi";
+		vi@54080000 {
+			compatible = "nvidia,tegra210-vi";
+			reg = <0x0 0x54080000 0x0 0x700>;
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			assigned-clocks = <&tegra_car TEGRA210_CLK_VI>;
+			assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>;
+
+			clocks = <&tegra_car TEGRA210_CLK_VI>;
+			power-domains = <&pd_venc>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0x0 0x0 0x54080000 0x2000>;
+
+			csi@838 {
+				compatible = "nvidia,tegra210-csi";
+				reg = <0x838 0x1300>;
+				assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>,
+						  <&tegra_car TEGRA210_CLK_CILCD>,
+						  <&tegra_car TEGRA210_CLK_CILE>,
+						  <&tegra_car TEGRA210_CLK_CSI_TPG>;
+				assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>,
+							 <&tegra_car TEGRA210_CLK_PLL_P>,
+							 <&tegra_car TEGRA210_CLK_PLL_P>;
+				assigned-clock-rates = <102000000>,
+						       <102000000>,
+						       <102000000>,
+						       <972000000>;
+
+				clocks = <&tegra_car TEGRA210_CLK_CSI>,
+					 <&tegra_car TEGRA210_CLK_CILAB>,
+					 <&tegra_car TEGRA210_CLK_CILCD>,
+					 <&tegra_car TEGRA210_CLK_CILE>,
+					 <&tegra_car TEGRA210_CLK_CSI_TPG>;
+				clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
+				power-domains = <&pd_sor>;
+			};
 		};
 
 		epp {

Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt

@@ -35,6 +35,12 @@ Required properties:
 	Due to above changes, Tegra114 I2C driver makes incompatible with
 	previous hardware driver. Hence, tegra114 I2C controller is compatible
 	with "nvidia,tegra114-i2c".
+  nvidia,tegra210-i2c-vi: Tegra210 has one I2C controller that is part of the
+	host1x domain and typically used for camera use-cases. This VI I2C
+	controller is mostly compatible with the programming model of the
+	regular I2C controllers with a few exceptions. The I2C registers start
+	at an offset of 0xc00 (instead of 0), registers are 16 bytes apart
+	(rather than 4) and the controller does not support slave mode.
 - reg: Should contain I2C controller registers physical address and length.
 - interrupts: Should contain I2C controller interrupts.
 - address-cells: Address cells for I2C device address.

Documentation/devicetree/bindings/memory-controllers/nvidia,tegra210-emc.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/nvidia,tegra210-emc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra210 SoC External Memory Controller
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Jon Hunter <jonathanh@nvidia.com>
+
+description: |
+  The EMC interfaces with the off-chip SDRAM to service the request stream
+  sent from the memory controller.
+
+properties:
+  compatible:
+    const: nvidia,tegra210-emc
+
+  reg:
+    maxItems: 3
+
+  clocks:
+    items:
+      - description: external memory clock
+
+  clock-names:
+    items:
+      - const: emc
+
+  interrupts:
+    items:
+      - description: EMC general interrupt
+
+  memory-region:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      phandle to a reserved memory region describing the table of EMC
+      frequencies trained by the firmware
+
+  nvidia,memory-controller:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      phandle of the memory controller node
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - nvidia,memory-controller
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/tegra210-car.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    reserved-memory {
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges;
+
+        emc_table: emc-table@83400000 {
+            compatible = "nvidia,tegra210-emc-table";
+            reg = <0x83400000 0x10000>;
+        };
+    };
+
+    external-memory-controller@7001b000 {
+        compatible = "nvidia,tegra210-emc";
+        reg = <0x7001b000 0x1000>,
+              <0x7001e000 0x1000>,
+              <0x7001f000 0x1000>;
+        clocks = <&tegra_car TEGRA210_CLK_EMC>;
+        clock-names = "emc";
+        interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+        memory-region = <&emc_table>;
+        nvidia,memory-controller = <&mc>;
+    };

include/dt-bindings/clock/tegra114-car.h

@@ -272,10 +272,10 @@
 #define TEGRA114_CLK_AUDIO3 242
 #define TEGRA114_CLK_AUDIO4 243
 #define TEGRA114_CLK_SPDIF 244
-#define TEGRA114_CLK_CLK_OUT_1 245
-#define TEGRA114_CLK_CLK_OUT_2 246
-#define TEGRA114_CLK_CLK_OUT_3 247
-#define TEGRA114_CLK_BLINK 248
+/* 245 */
+/* 246 */
+/* 247 */
+/* 248 */
 #define TEGRA114_CLK_OSC 249
 /* 250 */
 /* 251 */
@@ -335,9 +335,9 @@
 #define TEGRA114_CLK_AUDIO3_MUX 303
 #define TEGRA114_CLK_AUDIO4_MUX 304
 #define TEGRA114_CLK_SPDIF_MUX 305
-#define TEGRA114_CLK_CLK_OUT_1_MUX 306
-#define TEGRA114_CLK_CLK_OUT_2_MUX 307
-#define TEGRA114_CLK_CLK_OUT_3_MUX 308
+/* 306 */
+/* 307 */
+/* 308 */
 #define TEGRA114_CLK_DSIA_MUX 309
 #define TEGRA114_CLK_DSIB_MUX 310
 #define TEGRA114_CLK_XUSB_SS_DIV2 311

include/dt-bindings/clock/tegra124-car-common.h

@@ -271,10 +271,10 @@
 #define TEGRA124_CLK_AUDIO3 242
 #define TEGRA124_CLK_AUDIO4 243
 #define TEGRA124_CLK_SPDIF 244
-#define TEGRA124_CLK_CLK_OUT_1 245
-#define TEGRA124_CLK_CLK_OUT_2 246
-#define TEGRA124_CLK_CLK_OUT_3 247
-#define TEGRA124_CLK_BLINK 248
+/* 245 */
+/* 246 */
+/* 247 */
+/* 248 */
 #define TEGRA124_CLK_OSC 249
 /* 250 */
 /* 251 */
@@ -334,9 +334,9 @@
 #define TEGRA124_CLK_AUDIO3_MUX 303
 #define TEGRA124_CLK_AUDIO4_MUX 304
 #define TEGRA124_CLK_SPDIF_MUX 305
-#define TEGRA124_CLK_CLK_OUT_1_MUX 306
-#define TEGRA124_CLK_CLK_OUT_2_MUX 307
-#define TEGRA124_CLK_CLK_OUT_3_MUX 308
+/* 306 */
+/* 307 */
+/* 308 */
 /* 309 */
 /* 310 */
 #define TEGRA124_CLK_SOR0_LVDS 311 /* deprecated */

include/dt-bindings/clock/tegra20-car.h

@@ -131,7 +131,7 @@
 #define TEGRA20_CLK_CCLK 108
 #define TEGRA20_CLK_HCLK 109
 #define TEGRA20_CLK_PCLK 110
-#define TEGRA20_CLK_BLINK 111
+/* 111 */
 #define TEGRA20_CLK_PLL_A 112
 #define TEGRA20_CLK_PLL_A_OUT0 113
 #define TEGRA20_CLK_PLL_C 114

include/dt-bindings/clock/tegra210-car.h

@@ -306,10 +306,10 @@
 #define TEGRA210_CLK_AUDIO3 274
 #define TEGRA210_CLK_AUDIO4 275
 #define TEGRA210_CLK_SPDIF 276
-#define TEGRA210_CLK_CLK_OUT_1 277
-#define TEGRA210_CLK_CLK_OUT_2 278
-#define TEGRA210_CLK_CLK_OUT_3 279
-#define TEGRA210_CLK_BLINK 280
+/* 277 */
+/* 278 */
+/* 279 */
+/* 280 */
 #define TEGRA210_CLK_SOR0_LVDS 281 /* deprecated */
 #define TEGRA210_CLK_SOR0_OUT 281
 #define TEGRA210_CLK_SOR1_OUT 282
@@ -358,7 +358,7 @@
 #define TEGRA210_CLK_PLL_A_OUT0_OUT_ADSP 324
 /* 325 */
 #define TEGRA210_CLK_OSC 326
-/* 327 */
+#define TEGRA210_CLK_CSI_TPG 327
 /* 328 */
 /* 329 */
 /* 330 */
@@ -388,9 +388,9 @@
 #define TEGRA210_CLK_AUDIO3_MUX 353
 #define TEGRA210_CLK_AUDIO4_MUX 354
 #define TEGRA210_CLK_SPDIF_MUX 355
-#define TEGRA210_CLK_CLK_OUT_1_MUX 356
-#define TEGRA210_CLK_CLK_OUT_2_MUX 357
-#define TEGRA210_CLK_CLK_OUT_3_MUX 358
+/* 356 */
+/* 357 */
+/* 358 */
 #define TEGRA210_CLK_DSIA_MUX 359
 #define TEGRA210_CLK_DSIB_MUX 360
 /* 361 */

include/dt-bindings/clock/tegra30-car.h

@@ -232,11 +232,11 @@
 #define TEGRA30_CLK_AUDIO3 204
 #define TEGRA30_CLK_AUDIO4 205
 #define TEGRA30_CLK_SPDIF 206
-#define TEGRA30_CLK_CLK_OUT_1 207 /* (extern1) */
-#define TEGRA30_CLK_CLK_OUT_2 208 /* (extern2) */
-#define TEGRA30_CLK_CLK_OUT_3 209 /* (extern3) */
+/* 207 */
+/* 208 */
+/* 209 */
 #define TEGRA30_CLK_SCLK 210
-#define TEGRA30_CLK_BLINK 211
+/* 211 */
 #define TEGRA30_CLK_CCLK_G 212
 #define TEGRA30_CLK_CCLK_LP 213
 #define TEGRA30_CLK_TWD 214
@@ -262,9 +262,9 @@
 /* 297 */
 /* 298 */
 /* 299 */
-#define TEGRA30_CLK_CLK_OUT_1_MUX 300
-#define TEGRA30_CLK_CLK_OUT_2_MUX 301
-#define TEGRA30_CLK_CLK_OUT_3_MUX 302
+/* 300 */
+/* 301 */
+/* 302 */
 #define TEGRA30_CLK_AUDIO0_MUX 303
 #define TEGRA30_CLK_AUDIO1_MUX 304
 #define TEGRA30_CLK_AUDIO2_MUX 305