Merge branch 'next' of...

Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal into eduardo-soc

Documentation/devicetree/bindings/thermal/imx-thermal.txt

 * Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
 
 Required properties:
-- compatible : "fsl,imx6q-thermal"
+- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-tempmon" for i.MX6SX.
+  i.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC,
+  when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature
+  is higher than panic threshold, system will auto reboot by SRC module.
 - fsl,tempmon : phandle pointer to system controller that contains TEMPMON
   control registers, e.g. ANATOP on imx6q.
 - fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON

drivers/thermal/fair_share.c

@@ -23,6 +23,7 @@
  */
 
 #include <linux/thermal.h>
+#include <trace/events/thermal.h>
 
 #include "thermal_core.h"
 
@@ -34,6 +35,7 @@ static int get_trip_level(struct thermal_zone_device *tz)
 {
 	int count = 0;
 	unsigned long trip_temp;
+	enum thermal_trip_type trip_type;
 
 	if (tz->trips == 0 || !tz->ops->get_trip_temp)
 		return 0;
@@ -43,6 +45,16 @@ static int get_trip_level(struct thermal_zone_device *tz)
 		if (tz->temperature < trip_temp)
 			break;
 	}
+
+	/*
+	 * count > 0 only if temperature is greater than first trip
+	 * point, in which case, trip_point = count - 1
+	 */
+	if (count > 0) {
+		tz->ops->get_trip_type(tz, count - 1, &trip_type);
+		trace_thermal_zone_trip(tz, count - 1, trip_type);
+	}
+
 	return count;
 }
 

drivers/thermal/imx_thermal.c

@@ -19,6 +19,7 @@
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
@@ -31,6 +32,11 @@
 
 #define MISC0				0x0150
 #define MISC0_REFTOP_SELBIASOFF		(1 << 3)
+#define MISC1				0x0160
+#define MISC1_IRQ_TEMPHIGH		(1 << 29)
+/* Below LOW and PANIC bits are only for TEMPMON_IMX6SX */
+#define MISC1_IRQ_TEMPLOW		(1 << 28)
+#define MISC1_IRQ_TEMPPANIC		(1 << 27)
 
 #define TEMPSENSE0			0x0180
 #define TEMPSENSE0_ALARM_VALUE_SHIFT	20
@@ -43,6 +49,12 @@
 
 #define TEMPSENSE1			0x0190
 #define TEMPSENSE1_MEASURE_FREQ		0xffff
+/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
+#define TEMPSENSE2			0x0290
+#define TEMPSENSE2_LOW_VALUE_SHIFT	0
+#define TEMPSENSE2_LOW_VALUE_MASK	0xfff
+#define TEMPSENSE2_PANIC_VALUE_SHIFT	16
+#define TEMPSENSE2_PANIC_VALUE_MASK	0xfff0000
 
 #define OCOTP_ANA1			0x04e0
 
@@ -66,6 +78,21 @@ enum imx_thermal_trip {
 #define FACTOR1				15976
 #define FACTOR2				4297157
 
+#define TEMPMON_IMX6Q			1
+#define TEMPMON_IMX6SX			2
+
+struct thermal_soc_data {
+	u32 version;
+};
+
+static struct thermal_soc_data thermal_imx6q_data = {
+	.version = TEMPMON_IMX6Q,
+};
+
+static struct thermal_soc_data thermal_imx6sx_data = {
+	.version = TEMPMON_IMX6SX,
+};
+
 struct imx_thermal_data {
 	struct thermal_zone_device *tz;
 	struct thermal_cooling_device *cdev;
@@ -79,8 +106,21 @@ struct imx_thermal_data {
 	bool irq_enabled;
 	int irq;
 	struct clk *thermal_clk;
+	const struct thermal_soc_data *socdata;
 };
 
+static void imx_set_panic_temp(struct imx_thermal_data *data,
+			       signed long panic_temp)
+{
+	struct regmap *map = data->tempmon;
+	int critical_value;
+
+	critical_value = (data->c2 - panic_temp) / data->c1;
+	regmap_write(map, TEMPSENSE2 + REG_CLR, TEMPSENSE2_PANIC_VALUE_MASK);
+	regmap_write(map, TEMPSENSE2 + REG_SET, critical_value <<
+			TEMPSENSE2_PANIC_VALUE_SHIFT);
+}
+
 static void imx_set_alarm_temp(struct imx_thermal_data *data,
 			       signed long alarm_temp)
 {
@@ -142,14 +182,18 @@ static int imx_get_temp(struct thermal_zone_device *tz, unsigned long *temp)
 	/* See imx_get_sensor_data() for formula derivation */
 	*temp = data->c2 - n_meas * data->c1;
 
-	/* Update alarm value to next higher trip point */
-	if (data->alarm_temp == data->temp_passive && *temp >= data->temp_passive)
+	/* Update alarm value to next higher trip point for TEMPMON_IMX6Q */
+	if (data->socdata->version == TEMPMON_IMX6Q) {
+		if (data->alarm_temp == data->temp_passive &&
+			*temp >= data->temp_passive)
 			imx_set_alarm_temp(data, data->temp_critical);
-	if (data->alarm_temp == data->temp_critical && *temp < data->temp_passive) {
+		if (data->alarm_temp == data->temp_critical &&
+			*temp < data->temp_passive) {
 			imx_set_alarm_temp(data, data->temp_passive);
 			dev_dbg(&tz->device, "thermal alarm off: T < %lu\n",
 				data->alarm_temp / 1000);
 		}
+	}
 
 	if (*temp != data->last_temp) {
 		dev_dbg(&tz->device, "millicelsius: %ld\n", *temp);
@@ -398,8 +442,17 @@ static irqreturn_t imx_thermal_alarm_irq_thread(int irq, void *dev)
 	return IRQ_HANDLED;
 }
 
+static const struct of_device_id of_imx_thermal_match[] = {
+	{ .compatible = "fsl,imx6q-tempmon", .data = &thermal_imx6q_data, },
+	{ .compatible = "fsl,imx6sx-tempmon", .data = &thermal_imx6sx_data, },
+	{ /* end */ }
+};
+MODULE_DEVICE_TABLE(of, of_imx_thermal_match);
+
 static int imx_thermal_probe(struct platform_device *pdev)
 {
+	const struct of_device_id *of_id =
+		of_match_device(of_imx_thermal_match, &pdev->dev);
 	struct imx_thermal_data *data;
 	struct cpumask clip_cpus;
 	struct regmap *map;
@@ -418,6 +471,20 @@ static int imx_thermal_probe(struct platform_device *pdev)
 	}
 	data->tempmon = map;
 
+	data->socdata = of_id->data;
+
+	/* make sure the IRQ flag is clear before enabling irq on i.MX6SX */
+	if (data->socdata->version == TEMPMON_IMX6SX) {
+		regmap_write(map, MISC1 + REG_CLR, MISC1_IRQ_TEMPHIGH |
+			MISC1_IRQ_TEMPLOW | MISC1_IRQ_TEMPPANIC);
+		/*
+		 * reset value of LOW ALARM is incorrect, set it to lowest
+		 * value to avoid false trigger of low alarm.
+		 */
+		regmap_write(map, TEMPSENSE2 + REG_SET,
+			TEMPSENSE2_LOW_VALUE_MASK);
+	}
+
 	data->irq = platform_get_irq(pdev, 0);
 	if (data->irq < 0)
 		return data->irq;
@@ -489,6 +556,10 @@ static int imx_thermal_probe(struct platform_device *pdev)
 	measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
 	regmap_write(map, TEMPSENSE1 + REG_SET, measure_freq);
 	imx_set_alarm_temp(data, data->temp_passive);
+
+	if (data->socdata->version == TEMPMON_IMX6SX)
+		imx_set_panic_temp(data, data->temp_critical);
+
 	regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
 	regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
 
@@ -550,12 +621,6 @@ static int imx_thermal_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(imx_thermal_pm_ops,
 			 imx_thermal_suspend, imx_thermal_resume);
 
-static const struct of_device_id of_imx_thermal_match[] = {
-	{ .compatible = "fsl,imx6q-tempmon", },
-	{ /* end */ }
-};
-MODULE_DEVICE_TABLE(of, of_imx_thermal_match);
-
 static struct platform_driver imx_thermal = {
 	.driver = {
 		.name	= "imx_thermal",

drivers/thermal/of-thermal.c

@@ -401,6 +401,10 @@ thermal_zone_of_sensor_register(struct device *dev, int sensor_id,
 		struct of_phandle_args sensor_specs;
 		int ret, id;
 
+		/* Check whether child is enabled or not */
+		if (!of_device_is_available(child))
+			continue;
+
 		/* For now, thermal framework supports only 1 sensor per zone */
 		ret = of_parse_phandle_with_args(child, "thermal-sensors",
 						 "#thermal-sensor-cells",
@@ -771,6 +775,10 @@ int __init of_parse_thermal_zones(void)
 		struct thermal_zone_device *zone;
 		struct thermal_zone_params *tzp;
 
+		/* Check whether child is enabled or not */
+		if (!of_device_is_available(child))
+			continue;
+
 		tz = thermal_of_build_thermal_zone(child);
 		if (IS_ERR(tz)) {
 			pr_err("failed to build thermal zone %s: %ld\n",
@@ -838,6 +846,10 @@ void of_thermal_destroy_zones(void)
 	for_each_child_of_node(np, child) {
 		struct thermal_zone_device *zone;
 
+		/* Check whether child is enabled or not */
+		if (!of_device_is_available(child))
+			continue;
+
 		zone = thermal_zone_get_zone_by_name(child->name);
 		if (IS_ERR(zone))
 			continue;

drivers/thermal/step_wise.c

@@ -23,6 +23,7 @@
  */
 
 #include <linux/thermal.h>
+#include <trace/events/thermal.h>
 
 #include "thermal_core.h"
 
@@ -129,8 +130,10 @@ static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip)
 
 	trend = get_tz_trend(tz, trip);
 
-	if (tz->temperature >= trip_temp)
+	if (tz->temperature >= trip_temp) {
 		throttle = true;
+		trace_thermal_zone_trip(tz, trip, trip_type);
+	}
 
 	dev_dbg(&tz->device, "Trip%d[type=%d,temp=%ld]:trend=%d,throttle=%d\n",
 				trip, trip_type, trip_temp, trend, throttle);

drivers/thermal/thermal_core.c

@@ -38,6 +38,9 @@
 #include <net/netlink.h>
 #include <net/genetlink.h>
 
+#define CREATE_TRACE_POINTS
+#include <trace/events/thermal.h>
+
 #include "thermal_core.h"
 #include "thermal_hwmon.h"
 
@@ -368,6 +371,8 @@ static void handle_critical_trips(struct thermal_zone_device *tz,
 	if (tz->temperature < trip_temp)
 		return;
 
+	trace_thermal_zone_trip(tz, trip, trip_type);
+
 	if (tz->ops->notify)
 		tz->ops->notify(tz, trip, trip_type);
 
@@ -463,6 +468,7 @@ static void update_temperature(struct thermal_zone_device *tz)
 	tz->temperature = temp;
 	mutex_unlock(&tz->lock);
 
+	trace_thermal_temperature(tz);
 	dev_dbg(&tz->device, "last_temperature=%d, current_temperature=%d\n",
 				tz->last_temperature, tz->temperature);
 }
@@ -1287,6 +1293,7 @@ void thermal_cdev_update(struct thermal_cooling_device *cdev)
 	mutex_unlock(&cdev->lock);
 	cdev->ops->set_cur_state(cdev, target);
 	cdev->updated = true;
+	trace_cdev_update(cdev, target);
 	dev_dbg(&cdev->device, "set to state %lu\n", target);
 }
 EXPORT_SYMBOL(thermal_cdev_update);

include/trace/events/thermal.h

+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM thermal
+
+#if !defined(_TRACE_THERMAL_H) || defined(TRACE_HEADER_MULTI_READ)
+#define _TRACE_THERMAL_H
+
+#include <linux/thermal.h>
+#include <linux/tracepoint.h>
+
+TRACE_EVENT(thermal_temperature,
+
+	TP_PROTO(struct thermal_zone_device *tz),
+
+	TP_ARGS(tz),
+
+	TP_STRUCT__entry(
+		__string(thermal_zone, tz->type)
+		__field(int, id)
+		__field(int, temp_prev)
+		__field(int, temp)
+	),
+
+	TP_fast_assign(
+		__assign_str(thermal_zone, tz->type);
+		__entry->id = tz->id;
+		__entry->temp_prev = tz->last_temperature;
+		__entry->temp = tz->temperature;
+	),
+
+	TP_printk("thermal_zone=%s id=%d temp_prev=%d temp=%d",
+		__get_str(thermal_zone), __entry->id, __entry->temp_prev,
+		__entry->temp)
+);
+
+TRACE_EVENT(cdev_update,
+
+	TP_PROTO(struct thermal_cooling_device *cdev, unsigned long target),
+
+	TP_ARGS(cdev, target),
+
+	TP_STRUCT__entry(
+		__string(type, cdev->type)
+		__field(unsigned long, target)
+	),
+
+	TP_fast_assign(
+		__assign_str(type, cdev->type);
+		__entry->target = target;
+	),
+
+	TP_printk("type=%s target=%lu", __get_str(type), __entry->target)
+);
+
+TRACE_EVENT(thermal_zone_trip,
+
+	TP_PROTO(struct thermal_zone_device *tz, int trip,
+		enum thermal_trip_type trip_type),
+
+	TP_ARGS(tz, trip, trip_type),
+
+	TP_STRUCT__entry(
+		__string(thermal_zone, tz->type)
+		__field(int, id)
+		__field(int, trip)
+		__field(enum thermal_trip_type, trip_type)
+	),
+
+	TP_fast_assign(
+		__assign_str(thermal_zone, tz->type);
+		__entry->id = tz->id;
+		__entry->trip = trip;
+		__entry->trip_type = trip_type;
+	),
+
+	TP_printk("thermal_zone=%s id=%d trip=%d trip_type=%d",
+		__get_str(thermal_zone), __entry->id, __entry->trip,
+		__entry->trip_type)
+);
+
+#endif /* _TRACE_THERMAL_H */
+
+/* This part must be outside protection */
+#include <trace/define_trace.h>