Merge branch 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata updates from Tejun Heo:

 - a number of libata core changes to better support NCQ TRIM.

 - ahci now supports MSI-X in single IRQ mode to support a new
   controller which doesn't implement MSI or INTX.

 - ahci now supports edge-triggered IRQ mode to support a new controller
   which for some odd reason did edge-triggered IRQ.

 - the usual controller support additions and changes.

* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (27 commits)
  libata: Do not blacklist Micron M500DC
  ata: ahci_mvebu: add suspend/resume support
  ahci, msix: Fix build error for !PCI_MSI
  ahci: Add support for Cavium's ThunderX host controller
  ahci: Add generic MSI-X support for single interrupts to SATA PCI driver
  libata: finally use __initconst in ata_parse_force_one()
  drivers: ata: add support for Ceva sata host controller
  devicetree:bindings: add devicetree bindings for ceva ahci
  ahci: added support for Freescale AHCI sata
  ahci: Store irq number in struct ahci_host_priv
  ahci: Move interrupt enablement code to a separate function
  Doc: libata: Fix spelling typo found in libata.xml
  ata:sata_nv - Change 1 to true for bool type variable.
  ata: add Broadcom AHCI SATA3 driver for STB chips
  Documentation: devicetree: add Broadcom SATA binding
  libata: Fix regression when the NCQ Send and Receive log page is absent
  ata: hpt366: fix constant cast warning
  ata: ahci_xgene: potential NULL dereference in probe
  ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.
  libahci: Add support to handle HOST_IRQ_STAT as edge trigger latch.
  ...

Documentation/ABI/testing/sysfs-ata

@@ -90,6 +90,17 @@ gscr
 	130:	SATA_PMP_GSCR_SII_GPIO
 	Only valid if the device is a PM.
 
+trim
+
+	Shows the DSM TRIM mode currently used by the device. Valid
+	values are:
+	unsupported:		Drive does not support DSM TRIM
+	unqueued:		Drive supports unqueued DSM TRIM only
+	queued:			Drive supports queued DSM TRIM
+	forced_unqueued:	Drive's queued DSM support is known to be
+				buggy and only unqueued TRIM commands
+				are sent
+
 spdn_cnt
 
 	Number of time libata decided to lower the speed of link due to errors.

Documentation/devicetree/bindings/ata/ahci-ceva.txt

+Binding for CEVA AHCI SATA Controller
+
+Required properties:
+  - reg: Physical base address and size of the controller's register area.
+  - compatible: Compatibility string. Must be 'ceva,ahci-1v84'.
+  - clocks: Input clock specifier. Refer to common clock bindings.
+  - interrupts: Interrupt specifier. Refer to interrupt binding.
+
+Optional properties:
+  - ceva,broken-gen2: limit to gen1 speed instead of gen2.
+
+Examples:
+	ahci@fd0c0000 {
+		compatible = "ceva,ahci-1v84";
+		reg = <0xfd0c0000 0x200>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 133 4>;
+		clocks = <&clkc SATA_CLK_ID>;
+		ceva,broken-gen2;
+	};

Documentation/devicetree/bindings/ata/ahci-platform.txt

@@ -16,6 +16,8 @@ Required properties:
   - "snps,dwc-ahci"
   - "snps,exynos5440-ahci"
   - "snps,spear-ahci"
+  - "fsl,qoriq-ahci" : for qoriq series socs which include ls1021, ls2085, etc.
+  - "fsl,<chip>-ahci" : chip could be ls1021, ls2085 etc.
   - "generic-ahci"
 - interrupts        : <interrupt mapping for SATA IRQ>
 - reg               : <registers mapping>

Documentation/devicetree/bindings/ata/brcm,sata-brcmstb.txt

+* Broadcom SATA3 AHCI Controller for STB
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible         : compatible list, may contain "brcm,bcm7445-ahci" and/or
+                       "brcm,sata3-ahci"
+- reg                : register mappings for AHCI and SATA_TOP_CTRL
+- reg-names          : "ahci" and "top-ctrl"
+- interrupts         : interrupt mapping for SATA IRQ
+
+Also see ahci-platform.txt.
+
+Example:
+
+	sata@f045a000 {
+		compatible = "brcm,bcm7445-ahci", "brcm,sata3-ahci";
+		reg = <0xf045a000 0xa9c>, <0xf0458040 0x24>;
+		reg-names = "ahci", "top-ctrl";
+		interrupts = <0 30 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sata0: sata-port@0 {
+			reg = <0>;
+			phys = <&sata_phy 0>;
+		};
+
+		sata1: sata-port@1 {
+			reg = <1>;
+			phys = <&sata_phy 1>;
+		};
+	};

Documentation/kernel-parameters.txt

@@ -1791,6 +1791,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 
 			* [no]ncq: Turn on or off NCQ.
 
+			* [no]ncqtrim: Turn off queued DSM TRIM.
+
 			* nohrst, nosrst, norst: suppress hard, soft
                           and both resets.
 

drivers/ata/Kconfig

@@ -98,6 +98,15 @@ config SATA_AHCI_PLATFORM
 
 	  If unsure, say N.
 
+config AHCI_BRCMSTB
+	tristate "Broadcom STB AHCI SATA support"
+	depends on ARCH_BRCMSTB
+	help
+	  This option enables support for the AHCI SATA3 controller found on
+	  STB SoC's.
+
+	  If unsure, say N.
+
 config AHCI_DA850
 	tristate "DaVinci DA850 AHCI SATA support"
 	depends on ARCH_DAVINCI_DA850
@@ -124,6 +133,15 @@ config AHCI_IMX
 
 	  If unsure, say N.
 
+config AHCI_CEVA
+	tristate "CEVA AHCI SATA support"
+	depends on OF
+	help
+	  This option enables support for the CEVA AHCI SATA.
+	  It can be found on the Xilinx Zynq UltraScale+ MPSoC.
+
+	  If unsure, say N.
+
 config AHCI_MVEBU
 	tristate "Marvell EBU AHCI SATA support"
 	depends on ARCH_MVEBU

drivers/ata/Makefile

@@ -10,6 +10,8 @@ obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_SATA_SIL24)	+= sata_sil24.o
 obj-$(CONFIG_SATA_DWC)		+= sata_dwc_460ex.o
 obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
+obj-$(CONFIG_AHCI_BRCMSTB)	+= ahci_brcmstb.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_CEVA)		+= ahci_ceva.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_MVEBU)	+= ahci_mvebu.o libahci.o libahci_platform.o

drivers/ata/acard-ahci.c

@@ -433,6 +433,8 @@ static int acard_ahci_init_one(struct pci_dev *pdev, const struct pci_device_id
 	hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
 	if (!hpriv)
 		return -ENOMEM;
+
+	hpriv->irq = pdev->irq;
 	hpriv->flags |= (unsigned long)pi.private_data;
 
 	if (!(hpriv->flags & AHCI_HFLAG_NO_MSI))
@@ -498,7 +500,7 @@ static int acard_ahci_init_one(struct pci_dev *pdev, const struct pci_device_id
 	acard_ahci_pci_print_info(host);
 
 	pci_set_master(pdev);
-	return ahci_host_activate(host, pdev->irq, &acard_ahci_sht);
+	return ahci_host_activate(host, &acard_ahci_sht);
 }
 
 module_pci_driver(acard_ahci_pci_driver);

drivers/ata/ahci.c

@@ -42,6 +42,7 @@
 #include <linux/device.h>
 #include <linux/dmi.h>
 #include <linux/gfp.h>
+#include <linux/msi.h>
 #include <scsi/scsi_host.h>
 #include <scsi/scsi_cmnd.h>
 #include <linux/libata.h>
@@ -52,6 +53,7 @@
 
 enum {
 	AHCI_PCI_BAR_STA2X11	= 0,
+	AHCI_PCI_BAR_CAVIUM	= 0,
 	AHCI_PCI_BAR_ENMOTUS	= 2,
 	AHCI_PCI_BAR_STANDARD	= 5,
 };
@@ -1288,17 +1290,60 @@ static inline void ahci_gtf_filter_workaround(struct ata_host *host)
 {}
 #endif
 
-static int ahci_init_interrupts(struct pci_dev *pdev, unsigned int n_ports,
+/*
+ * ahci_init_msix() only implements single MSI-X support, not multiple
+ * MSI-X per-port interrupts. This is needed for host controllers that only
+ * have MSI-X support implemented, but no MSI or intx.
+ */
+static int ahci_init_msix(struct pci_dev *pdev, unsigned int n_ports,
+			  struct ahci_host_priv *hpriv)
+{
+	int rc, nvec;
+	struct msix_entry entry = {};
+
+	/* Do not init MSI-X if MSI is disabled for the device */
+	if (hpriv->flags & AHCI_HFLAG_NO_MSI)
+		return -ENODEV;
+
+	nvec = pci_msix_vec_count(pdev);
+	if (nvec < 0)
+		return nvec;
+
+	if (!nvec) {
+		rc = -ENODEV;
+		goto fail;
+	}
+
+	/*
+	 * There can be more than one vector (e.g. for error detection or
+	 * hdd hotplug). Only the first vector (entry.entry = 0) is used.
+	 */
+	rc = pci_enable_msix_exact(pdev, &entry, 1);
+	if (rc < 0)
+		goto fail;
+
+	hpriv->irq = entry.vector;
+
+	return 1;
+fail:
+	dev_err(&pdev->dev,
+		"failed to enable MSI-X with error %d, # of vectors: %d\n",
+		rc, nvec);
+
+	return rc;
+}
+
+static int ahci_init_msi(struct pci_dev *pdev, unsigned int n_ports,
 			struct ahci_host_priv *hpriv)
 {
 	int rc, nvec;
 
 	if (hpriv->flags & AHCI_HFLAG_NO_MSI)
-		goto intx;
+		return -ENODEV;
 
 	nvec = pci_msi_vec_count(pdev);
 	if (nvec < 0)
-		goto intx;
+		return nvec;
 
 	/*
 	 * If number of MSIs is less than number of ports then Sharing Last
@@ -1311,8 +1356,8 @@ static int ahci_init_interrupts(struct pci_dev *pdev, unsigned int n_ports,
 	rc = pci_enable_msi_exact(pdev, nvec);
 	if (rc == -ENOSPC)
 		goto single_msi;
-	else if (rc < 0)
-		goto intx;
+	if (rc < 0)
+		return rc;
 
 	/* fallback to single MSI mode if the controller enforced MRSM mode */
 	if (readl(hpriv->mmio + HOST_CTL) & HOST_MRSM) {
@@ -1324,15 +1369,42 @@ static int ahci_init_interrupts(struct pci_dev *pdev, unsigned int n_ports,
 	if (nvec > 1)
 		hpriv->flags |= AHCI_HFLAG_MULTI_MSI;
 
-	return nvec;
+	goto out;
 
 single_msi:
-	if (pci_enable_msi(pdev))
-		goto intx;
-	return 1;
+	nvec = 1;
+
+	rc = pci_enable_msi(pdev);
+	if (rc < 0)
+		return rc;
+out:
+	hpriv->irq = pdev->irq;
 
-intx:
+	return nvec;
+}
+
+static int ahci_init_interrupts(struct pci_dev *pdev, unsigned int n_ports,
+				struct ahci_host_priv *hpriv)
+{
+	int nvec;
+
+	nvec = ahci_init_msi(pdev, n_ports, hpriv);
+	if (nvec >= 0)
+		return nvec;
+
+	/*
+	 * Currently, MSI-X support only implements single IRQ mode and
+	 * exists for controllers which can't do other types of IRQ. Only
+	 * set it up if MSI fails.
+	 */
+	nvec = ahci_init_msix(pdev, n_ports, hpriv);
+	if (nvec >= 0)
+		return nvec;
+
+	/* lagacy intx interrupts */
 	pci_intx(pdev, 1);
+	hpriv->irq = pdev->irq;
+
 	return 0;
 }
 
@@ -1371,11 +1443,13 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 		dev_info(&pdev->dev,
 			 "PDC42819 can only drive SATA devices with this driver\n");
 
-	/* Both Connext and Enmotus devices use non-standard BARs */
+	/* Some devices use non-standard BARs */
 	if (pdev->vendor == PCI_VENDOR_ID_STMICRO && pdev->device == 0xCC06)
 		ahci_pci_bar = AHCI_PCI_BAR_STA2X11;
 	else if (pdev->vendor == 0x1c44 && pdev->device == 0x8000)
 		ahci_pci_bar = AHCI_PCI_BAR_ENMOTUS;
+	else if (pdev->vendor == 0x177d && pdev->device == 0xa01c)
+		ahci_pci_bar = AHCI_PCI_BAR_CAVIUM;
 
 	/*
 	 * The JMicron chip 361/363 contains one SATA controller and one
@@ -1497,13 +1571,13 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	 */
 	n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
 
-	ahci_init_interrupts(pdev, n_ports, hpriv);
-
 	host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
 	if (!host)
 		return -ENOMEM;
 	host->private_data = hpriv;
 
+	ahci_init_interrupts(pdev, n_ports, hpriv);
+
 	if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
 		host->flags |= ATA_HOST_PARALLEL_SCAN;
 	else
@@ -1549,7 +1623,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	pci_set_master(pdev);
 
-	return ahci_host_activate(host, pdev->irq, &ahci_sht);
+	return ahci_host_activate(host, &ahci_sht);
 }
 
 module_pci_driver(ahci_pci_driver);

drivers/ata/ahci.h

@@ -238,6 +238,8 @@ enum {
 	AHCI_HFLAG_MULTI_MSI		= (1 << 16), /* multiple PCI MSIs */
 	AHCI_HFLAG_NO_DEVSLP		= (1 << 17), /* no device sleep */
 	AHCI_HFLAG_NO_FBS		= (1 << 18), /* no FBS */
+	AHCI_HFLAG_EDGE_IRQ		= (1 << 19), /* HOST_IRQ_STAT behaves as
+							Edge Triggered */
 
 	/* ap->flags bits */
 
@@ -341,6 +343,7 @@ struct ahci_host_priv {
 	struct phy		**phys;
 	unsigned		nports;		/* Number of ports */
 	void			*plat_data;	/* Other platform data */
+	unsigned int		irq;		/* interrupt line */
 	/*
 	 * Optional ahci_start_engine override, if not set this gets set to the
 	 * default ahci_start_engine during ahci_save_initial_config, this can
@@ -393,8 +396,7 @@ void ahci_set_em_messages(struct ahci_host_priv *hpriv,
 			  struct ata_port_info *pi);
 int ahci_reset_em(struct ata_host *host);
 void ahci_print_info(struct ata_host *host, const char *scc_s);
-int ahci_host_activate(struct ata_host *host, int irq,
-		       struct scsi_host_template *sht);
+int ahci_host_activate(struct ata_host *host, struct scsi_host_template *sht);
 void ahci_error_handler(struct ata_port *ap);
 
 static inline void __iomem *__ahci_port_base(struct ata_host *host,

drivers/ata/ahci_brcmstb.c

+/*
+ * Broadcom SATA3 AHCI Controller Driver
+ *
+ * Copyright © 2009-2015 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/ahci_platform.h>
+#include <linux/compiler.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/libata.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+
+#include "ahci.h"
+
+#define DRV_NAME					"brcm-ahci"
+
+#define SATA_TOP_CTRL_VERSION				0x0
+#define SATA_TOP_CTRL_BUS_CTRL				0x4
+ #define MMIO_ENDIAN_SHIFT				0 /* CPU->AHCI */
+ #define DMADESC_ENDIAN_SHIFT				2 /* AHCI->DDR */
+ #define DMADATA_ENDIAN_SHIFT				4 /* AHCI->DDR */
+ #define PIODATA_ENDIAN_SHIFT				6
+  #define ENDIAN_SWAP_NONE				0
+  #define ENDIAN_SWAP_FULL				2
+ #define OVERRIDE_HWINIT				BIT(16)
+#define SATA_TOP_CTRL_TP_CTRL				0x8
+#define SATA_TOP_CTRL_PHY_CTRL				0xc
+ #define SATA_TOP_CTRL_PHY_CTRL_1			0x0
+  #define SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE	BIT(14)
+ #define SATA_TOP_CTRL_PHY_CTRL_2			0x4
+  #define SATA_TOP_CTRL_2_SW_RST_MDIOREG		BIT(0)
+  #define SATA_TOP_CTRL_2_SW_RST_OOB			BIT(1)
+  #define SATA_TOP_CTRL_2_SW_RST_RX			BIT(2)
+  #define SATA_TOP_CTRL_2_SW_RST_TX			BIT(3)
+  #define SATA_TOP_CTRL_2_PHY_GLOBAL_RESET		BIT(14)
+ #define SATA_TOP_CTRL_PHY_OFFS				0x8
+ #define SATA_TOP_MAX_PHYS				2
+#define SATA_TOP_CTRL_SATA_TP_OUT			0x1c
+#define SATA_TOP_CTRL_CLIENT_INIT_CTRL			0x20
+
+/* On big-endian MIPS, buses are reversed to big endian, so switch them back */
+#if defined(CONFIG_MIPS) && defined(__BIG_ENDIAN)
+#define DATA_ENDIAN			 2 /* AHCI->DDR inbound accesses */
+#define MMIO_ENDIAN			 2 /* CPU->AHCI outbound accesses */
+#else
+#define DATA_ENDIAN			 0
+#define MMIO_ENDIAN			 0
+#endif
+
+#define BUS_CTRL_ENDIAN_CONF				\
+	((DATA_ENDIAN << DMADATA_ENDIAN_SHIFT) |	\
+	(DATA_ENDIAN << DMADESC_ENDIAN_SHIFT) |		\
+	(MMIO_ENDIAN << MMIO_ENDIAN_SHIFT))
+
+struct brcm_ahci_priv {
+	struct device *dev;
+	void __iomem *top_ctrl;
+	u32 port_mask;
+};
+
+static const struct ata_port_info ahci_brcm_port_info = {
+	.flags		= AHCI_FLAG_COMMON,
+	.pio_mask	= ATA_PIO4,
+	.udma_mask	= ATA_UDMA6,
+	.port_ops	= &ahci_platform_ops,
+};
+
+static inline u32 brcm_sata_readreg(void __iomem *addr)
+{
+	/*
+	 * MIPS endianness is configured by boot strap, which also reverses all
+	 * bus endianness (i.e., big-endian CPU + big endian bus ==> native
+	 * endian I/O).
+	 *
+	 * Other architectures (e.g., ARM) either do not support big endian, or
+	 * else leave I/O in little endian mode.
+	 */
+	if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(__BIG_ENDIAN))
+		return __raw_readl(addr);
+	else
+		return readl_relaxed(addr);
+}
+
+static inline void brcm_sata_writereg(u32 val, void __iomem *addr)
+{
+	/* See brcm_sata_readreg() comments */
+	if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(__BIG_ENDIAN))
+		__raw_writel(val, addr);
+	else
+		writel_relaxed(val, addr);
+}
+
+static void brcm_sata_phy_enable(struct brcm_ahci_priv *priv, int port)
+{
+	void __iomem *phyctrl = priv->top_ctrl + SATA_TOP_CTRL_PHY_CTRL +
+				(port * SATA_TOP_CTRL_PHY_OFFS);
+	void __iomem *p;
+	u32 reg;
+
+	/* clear PHY_DEFAULT_POWER_STATE */
+	p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_1;
+	reg = brcm_sata_readreg(p);
+	reg &= ~SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE;
+	brcm_sata_writereg(reg, p);
+
+	/* reset the PHY digital logic */
+	p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_2;
+	reg = brcm_sata_readreg(p);
+	reg &= ~(SATA_TOP_CTRL_2_SW_RST_MDIOREG | SATA_TOP_CTRL_2_SW_RST_OOB |
+		 SATA_TOP_CTRL_2_SW_RST_RX);
+	reg |= SATA_TOP_CTRL_2_SW_RST_TX;
+	brcm_sata_writereg(reg, p);
+	reg = brcm_sata_readreg(p);
+	reg |= SATA_TOP_CTRL_2_PHY_GLOBAL_RESET;
+	brcm_sata_writereg(reg, p);
+	reg = brcm_sata_readreg(p);
+	reg &= ~SATA_TOP_CTRL_2_PHY_GLOBAL_RESET;
+	brcm_sata_writereg(reg, p);
+	(void)brcm_sata_readreg(p);
+}
+
+static void brcm_sata_phy_disable(struct brcm_ahci_priv *priv, int port)
+{
+	void __iomem *phyctrl = priv->top_ctrl + SATA_TOP_CTRL_PHY_CTRL +
+				(port * SATA_TOP_CTRL_PHY_OFFS);
+	void __iomem *p;
+	u32 reg;
+
+	/* power-off the PHY digital logic */
+	p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_2;
+	reg = brcm_sata_readreg(p);
+	reg |= (SATA_TOP_CTRL_2_SW_RST_MDIOREG | SATA_TOP_CTRL_2_SW_RST_OOB |
+		SATA_TOP_CTRL_2_SW_RST_RX | SATA_TOP_CTRL_2_SW_RST_TX |
+		SATA_TOP_CTRL_2_PHY_GLOBAL_RESET);
+	brcm_sata_writereg(reg, p);
+
+	/* set PHY_DEFAULT_POWER_STATE */
+	p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_1;
+	reg = brcm_sata_readreg(p);
+	reg |= SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE;
+	brcm_sata_writereg(reg, p);
+}
+
+static void brcm_sata_phys_enable(struct brcm_ahci_priv *priv)
+{
+	int i;
+
+	for (i = 0; i < SATA_TOP_MAX_PHYS; i++)
+		if (priv->port_mask & BIT(i))
+			brcm_sata_phy_enable(priv, i);
+}
+
+static void brcm_sata_phys_disable(struct brcm_ahci_priv *priv)
+{
+	int i;
+
+	for (i = 0; i < SATA_TOP_MAX_PHYS; i++)
+		if (priv->port_mask & BIT(i))
+			brcm_sata_phy_disable(priv, i);
+}
+
+static u32 brcm_ahci_get_portmask(struct platform_device *pdev,
+				  struct brcm_ahci_priv *priv)
+{
+	void __iomem *ahci;
+	struct resource *res;
+	u32 impl;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ahci");
+	ahci = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ahci))
+		return 0;
+
+	impl = readl(ahci + HOST_PORTS_IMPL);
+
+	if (fls(impl) > SATA_TOP_MAX_PHYS)
+		dev_warn(priv->dev, "warning: more ports than PHYs (%#x)\n",
+			 impl);
+	else if (!impl)
+		dev_info(priv->dev, "no ports found\n");
+
+	devm_iounmap(&pdev->dev, ahci);
+	devm_release_mem_region(&pdev->dev, res->start, resource_size(res));
+
+	return impl;
+}
+
+static void brcm_sata_init(struct brcm_ahci_priv *priv)
+{
+	/* Configure endianness */
+	brcm_sata_writereg(BUS_CTRL_ENDIAN_CONF,
+			   priv->top_ctrl + SATA_TOP_CTRL_BUS_CTRL);
+}
+
+static int brcm_ahci_suspend(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	struct brcm_ahci_priv *priv = hpriv->plat_data;
+	int ret;
+
+	ret = ahci_platform_suspend(dev);
+	brcm_sata_phys_disable(priv);
+	return ret;
+}
+
+static int brcm_ahci_resume(struct device *dev)
+{
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	struct brcm_ahci_priv *priv = hpriv->plat_data;
+
+	brcm_sata_init(priv);
+	brcm_sata_phys_enable(priv);
+	return ahci_platform_resume(dev);
+}
+
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
+static int brcm_ahci_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct brcm_ahci_priv *priv;
+	struct ahci_host_priv *hpriv;
+	struct resource *res;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+	priv->dev = dev;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "top-ctrl");
+	priv->top_ctrl = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->top_ctrl))
+		return PTR_ERR(priv->top_ctrl);
+
+	brcm_sata_init(priv);
+
+	priv->port_mask = brcm_ahci_get_portmask(pdev, priv);
+	if (!priv->port_mask)
+		return -ENODEV;
+
+	brcm_sata_phys_enable(priv);
+
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+	hpriv->plat_data = priv;
+
+	ret = ahci_platform_enable_resources(hpriv);
+	if (ret)
+		return ret;
+
+	ret = ahci_platform_init_host(pdev, hpriv, &ahci_brcm_port_info,
+				      &ahci_platform_sht);
+	if (ret)
+		return ret;
+
+	dev_info(dev, "Broadcom AHCI SATA3 registered\n");
+
+	return 0;
+}
+
+static int brcm_ahci_remove(struct platform_device *pdev)
+{
+	struct ata_host *host = dev_get_drvdata(&pdev->dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	struct brcm_ahci_priv *priv = hpriv->plat_data;
+	int ret;
+
+	ret = ata_platform_remove_one(pdev);
+	if (ret)
+		return ret;
+
+	brcm_sata_phys_disable(priv);
+
+	return 0;
+}
+
+static const struct of_device_id ahci_of_match[] = {
+	{.compatible = "brcm,bcm7445-ahci"},
+	{},
+};
+MODULE_DEVICE_TABLE(of, ahci_of_match);
+
+static SIMPLE_DEV_PM_OPS(ahci_brcm_pm_ops, brcm_ahci_suspend, brcm_ahci_resume);
+
+static struct platform_driver brcm_ahci_driver = {
+	.probe = brcm_ahci_probe,
+	.remove = brcm_ahci_remove,
+	.driver = {
+		.name = DRV_NAME,
+		.of_match_table = ahci_of_match,
+		.pm = &ahci_brcm_pm_ops,
+	},
+};
+module_platform_driver(brcm_ahci_driver);
+
+MODULE_DESCRIPTION("Broadcom SATA3 AHCI Controller Driver");
+MODULE_AUTHOR("Brian Norris");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:sata-brcmstb");

drivers/ata/ahci_ceva.c

+/*
+ * Copyright (C) 2015 Xilinx, Inc.
+ * CEVA AHCI SATA platform driver
+ *
+ * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/ahci_platform.h>
+#include <linux/kernel.h>
+#include <linux/libata.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "ahci.h"
+
+/* Vendor Specific Register Offsets */
+#define AHCI_VEND_PCFG  0xA4
+#define AHCI_VEND_PPCFG 0xA8
+#define AHCI_VEND_PP2C  0xAC
+#define AHCI_VEND_PP3C  0xB0
+#define AHCI_VEND_PP4C  0xB4
+#define AHCI_VEND_PP5C  0xB8
+#define AHCI_VEND_PAXIC 0xC0
+#define AHCI_VEND_PTC   0xC8
+
+/* Vendor Specific Register bit definitions */
+#define PAXIC_ADBW_BW64 0x1
+#define PAXIC_MAWIDD	(1 << 8)
+#define PAXIC_MARIDD	(1 << 16)
+#define PAXIC_OTL	(0x4 << 20)
+
+#define PCFG_TPSS_VAL	(0x32 << 16)
+#define PCFG_TPRS_VAL	(0x2 << 12)
+#define PCFG_PAD_VAL	0x2
+
+#define PPCFG_TTA	0x1FFFE
+#define PPCFG_PSSO_EN	(1 << 28)
+#define PPCFG_PSS_EN	(1 << 29)
+#define PPCFG_ESDF_EN	(1 << 31)
+
+#define PP2C_CIBGMN	0x0F
+#define PP2C_CIBGMX	(0x25 << 8)
+#define PP2C_CIBGN	(0x18 << 16)
+#define PP2C_CINMP	(0x29 << 24)
+
+#define PP3C_CWBGMN	0x04
+#define PP3C_CWBGMX	(0x0B << 8)
+#define PP3C_CWBGN	(0x08 << 16)
+#define PP3C_CWNMP	(0x0F << 24)
+
+#define PP4C_BMX	0x0a
+#define PP4C_BNM	(0x08 << 8)
+#define PP4C_SFD	(0x4a << 16)
+#define PP4C_PTST	(0x06 << 24)
+
+#define PP5C_RIT	0x60216
+#define PP5C_RCT	(0x7f0 << 20)
+
+#define PTC_RX_WM_VAL	0x40
+#define PTC_RSVD	(1 << 27)
+
+#define PORT0_BASE	0x100
+#define PORT1_BASE	0x180
+
+/* Port Control Register Bit Definitions */
+#define PORT_SCTL_SPD_GEN2	(0x2 << 4)
+#define PORT_SCTL_SPD_GEN1	(0x1 << 4)
+#define PORT_SCTL_IPM		(0x3 << 8)
+
+#define PORT_BASE	0x100
+#define PORT_OFFSET	0x80
+#define NR_PORTS	2
+#define DRV_NAME	"ahci-ceva"
+#define CEVA_FLAG_BROKEN_GEN2	1
+
+struct ceva_ahci_priv {
+	struct platform_device *ahci_pdev;
+	int flags;
+};
+
+static struct ata_port_operations ahci_ceva_ops = {
+	.inherits = &ahci_platform_ops,
+};
+
+static const struct ata_port_info ahci_ceva_port_info = {
+	.flags          = AHCI_FLAG_COMMON,
+	.pio_mask       = ATA_PIO4,
+	.udma_mask      = ATA_UDMA6,
+	.port_ops	= &ahci_ceva_ops,
+};
+
+static void ahci_ceva_setup(struct ahci_host_priv *hpriv)
+{
+	void __iomem *mmio = hpriv->mmio;
+	struct ceva_ahci_priv *cevapriv = hpriv->plat_data;
+	u32 tmp;
+	int i;
+
+	/*
+	 * AXI Data bus width to 64
+	 * Set Mem Addr Read, Write ID for data transfers
+	 * Transfer limit to 72 DWord
+	 */
+	tmp = PAXIC_ADBW_BW64 | PAXIC_MAWIDD | PAXIC_MARIDD | PAXIC_OTL;
+	writel(tmp, mmio + AHCI_VEND_PAXIC);
+
+	/* Set AHCI Enable */
+	tmp = readl(mmio + HOST_CTL);
+	tmp |= HOST_AHCI_EN;
+	writel(tmp, mmio + HOST_CTL);
+
+	for (i = 0; i < NR_PORTS; i++) {
+		/* TPSS TPRS scalars, CISE and Port Addr */
+		tmp = PCFG_TPSS_VAL | PCFG_TPRS_VAL | (PCFG_PAD_VAL + i);
+		writel(tmp, mmio + AHCI_VEND_PCFG);
+
+		/* Port Phy Cfg register enables */
+		tmp = PPCFG_TTA | PPCFG_PSS_EN | PPCFG_ESDF_EN;
+		writel(tmp, mmio + AHCI_VEND_PPCFG);
+
+		/* Phy Control OOB timing parameters COMINIT */
+		tmp = PP2C_CIBGMN | PP2C_CIBGMX | PP2C_CIBGN | PP2C_CINMP;
+		writel(tmp, mmio + AHCI_VEND_PP2C);
+
+		/* Phy Control OOB timing parameters COMWAKE */
+		tmp = PP3C_CWBGMN | PP3C_CWBGMX | PP3C_CWBGN | PP3C_CWNMP;
+		writel(tmp, mmio + AHCI_VEND_PP3C);
+
+		/* Phy Control Burst timing setting */
+		tmp = PP4C_BMX | PP4C_BNM | PP4C_SFD | PP4C_PTST;
+		writel(tmp, mmio + AHCI_VEND_PP4C);
+
+		/* Rate Change Timer and Retry Interval Timer setting */
+		tmp = PP5C_RIT | PP5C_RCT;
+		writel(tmp, mmio + AHCI_VEND_PP5C);
+
+		/* Rx Watermark setting  */
+		tmp = PTC_RX_WM_VAL | PTC_RSVD;
+		writel(tmp, mmio + AHCI_VEND_PTC);
+
+		/* Default to Gen 2 Speed and Gen 1 if Gen2 is broken */
+		tmp = PORT_SCTL_SPD_GEN2 | PORT_SCTL_IPM;
+		if (cevapriv->flags & CEVA_FLAG_BROKEN_GEN2)
+			tmp = PORT_SCTL_SPD_GEN1 | PORT_SCTL_IPM;
+		writel(tmp, mmio + PORT_SCR_CTL + PORT_BASE + PORT_OFFSET * i);
+	}
+}
+
+static struct scsi_host_template ahci_platform_sht = {
+	AHCI_SHT(DRV_NAME),
+};
+
+static int ceva_ahci_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct ahci_host_priv *hpriv;
+	struct ceva_ahci_priv *cevapriv;
+	int rc;
+
+	cevapriv = devm_kzalloc(dev, sizeof(*cevapriv), GFP_KERNEL);
+	if (!cevapriv)
+		return -ENOMEM;
+
+	cevapriv->ahci_pdev = pdev;
+
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	if (of_property_read_bool(np, "ceva,broken-gen2"))
+		cevapriv->flags = CEVA_FLAG_BROKEN_GEN2;
+
+	hpriv->plat_data = cevapriv;
+
+	/* CEVA specific initialization */
+	ahci_ceva_setup(hpriv);
+
+	rc = ahci_platform_init_host(pdev, hpriv, &ahci_ceva_port_info,
+					&ahci_platform_sht);
+	if (rc)
+		goto disable_resources;
+
+	return 0;
+
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+	return rc;
+}
+
+static int __maybe_unused ceva_ahci_suspend(struct device *dev)
+{
+	return ahci_platform_suspend_host(dev);
+}
+
+static int __maybe_unused ceva_ahci_resume(struct device *dev)
+{
+	return ahci_platform_resume_host(dev);
+}
+
+static SIMPLE_DEV_PM_OPS(ahci_ceva_pm_ops, ceva_ahci_suspend, ceva_ahci_resume);
+
+static const struct of_device_id ceva_ahci_of_match[] = {
+	{ .compatible = "ceva,ahci-1v84" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ceva_ahci_of_match);
+
+static struct platform_driver ceva_ahci_driver = {
+	.probe = ceva_ahci_probe,
+	.remove = ata_platform_remove_one,
+	.driver = {
+		.name = DRV_NAME,
+		.of_match_table = ceva_ahci_of_match,
+		.pm = &ahci_ceva_pm_ops,
+	},
+};
+module_platform_driver(ceva_ahci_driver);
+
+MODULE_DESCRIPTION("CEVA AHCI SATA platform driver");
+MODULE_AUTHOR("Xilinx Inc.");
+MODULE_LICENSE("GPL v2");

drivers/ata/ahci_mvebu.c

@@ -62,6 +62,26 @@ static void ahci_mvebu_regret_option(struct ahci_host_priv *hpriv)
 	writel(0x80, hpriv->mmio + AHCI_VENDOR_SPECIFIC_0_DATA);
 }
 
+static int ahci_mvebu_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	return ahci_platform_suspend_host(&pdev->dev);
+}
+
+static int ahci_mvebu_resume(struct platform_device *pdev)
+{
+	struct ata_host *host = platform_get_drvdata(pdev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	const struct mbus_dram_target_info *dram;
+
+	dram = mv_mbus_dram_info();
+	if (dram)
+		ahci_mvebu_mbus_config(hpriv, dram);
+
+	ahci_mvebu_regret_option(hpriv);
+
+	return ahci_platform_resume_host(&pdev->dev);
+}
+
 static const struct ata_port_info ahci_mvebu_port_info = {
 	.flags	   = AHCI_FLAG_COMMON,
 	.pio_mask  = ATA_PIO4,
@@ -120,6 +140,8 @@ MODULE_DEVICE_TABLE(of, ahci_mvebu_of_match);
 static struct platform_driver ahci_mvebu_driver = {
 	.probe = ahci_mvebu_probe,
 	.remove = ata_platform_remove_one,
+	.suspend = ahci_mvebu_suspend,
+	.resume = ahci_mvebu_resume,
 	.driver = {
 		.name = DRV_NAME,
 		.of_match_table = ahci_mvebu_of_match,

drivers/ata/ahci_platform.c

@@ -74,6 +74,7 @@ static const struct of_device_id ahci_of_match[] = {
 	{ .compatible = "ibm,476gtr-ahci", },
 	{ .compatible = "snps,dwc-ahci", },
 	{ .compatible = "hisilicon,hisi-ahci", },
+	{ .compatible = "fsl,qoriq-ahci", },
 	{},
 };
 MODULE_DEVICE_TABLE(of, ahci_of_match);

drivers/ata/ahci_xgene.c

@@ -27,6 +27,7 @@
 #include <linux/platform_device.h>
 #include <linux/ahci_platform.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/of_irq.h>
 #include <linux/phy/phy.h>
 #include "ahci.h"
@@ -84,6 +85,11 @@
 /* Max retry for link down */
 #define MAX_LINK_DOWN_RETRY 3
 
+enum xgene_ahci_version {
+	XGENE_AHCI_V1 = 1,
+	XGENE_AHCI_V2,
+};
+
 struct xgene_ahci_context {
 	struct ahci_host_priv *hpriv;
 	struct device *dev;
@@ -542,7 +548,7 @@ static int xgene_ahci_softreset(struct ata_link *link, unsigned int *class,
 	return rc;
 }
 
-static struct ata_port_operations xgene_ahci_ops = {
+static struct ata_port_operations xgene_ahci_v1_ops = {
 	.inherits = &ahci_ops,
 	.host_stop = xgene_ahci_host_stop,
 	.hardreset = xgene_ahci_hardreset,
@@ -552,11 +558,25 @@ static struct ata_port_operations xgene_ahci_ops = {
 	.pmp_softreset = xgene_ahci_pmp_softreset
 };
 
-static const struct ata_port_info xgene_ahci_port_info = {
+static const struct ata_port_info xgene_ahci_v1_port_info = {
+	.flags = AHCI_FLAG_COMMON | ATA_FLAG_PMP,
+	.pio_mask = ATA_PIO4,
+	.udma_mask = ATA_UDMA6,
+	.port_ops = &xgene_ahci_v1_ops,
+};
+
+static struct ata_port_operations xgene_ahci_v2_ops = {
+	.inherits = &ahci_ops,
+	.host_stop = xgene_ahci_host_stop,
+	.hardreset = xgene_ahci_hardreset,
+	.read_id = xgene_ahci_read_id,
+};
+
+static const struct ata_port_info xgene_ahci_v2_port_info = {
 	.flags = AHCI_FLAG_COMMON | ATA_FLAG_PMP,
 	.pio_mask = ATA_PIO4,
 	.udma_mask = ATA_UDMA6,
-	.port_ops = &xgene_ahci_ops,
+	.port_ops = &xgene_ahci_v2_ops,
 };
 
 static int xgene_ahci_hw_init(struct ahci_host_priv *hpriv)
@@ -629,12 +649,32 @@ static struct scsi_host_template ahci_platform_sht = {
 	AHCI_SHT(DRV_NAME),
 };
 
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id xgene_ahci_acpi_match[] = {
+	{ "APMC0D0D", XGENE_AHCI_V1},
+	{ "APMC0D32", XGENE_AHCI_V2},
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, xgene_ahci_acpi_match);
+#endif
+
+static const struct of_device_id xgene_ahci_of_match[] = {
+	{.compatible = "apm,xgene-ahci", .data = (void *) XGENE_AHCI_V1},
+	{.compatible = "apm,xgene-ahci-v2", .data = (void *) XGENE_AHCI_V2},
+	{},
+};
+MODULE_DEVICE_TABLE(of, xgene_ahci_of_match);
+
 static int xgene_ahci_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct ahci_host_priv *hpriv;
 	struct xgene_ahci_context *ctx;
 	struct resource *res;
+	const struct of_device_id *of_devid;
+	enum xgene_ahci_version version = XGENE_AHCI_V1;
+	const struct ata_port_info *ppi[] = { &xgene_ahci_v1_port_info,
+					      &xgene_ahci_v2_port_info };
 	int rc;
 
 	hpriv = ahci_platform_get_resources(pdev);
@@ -677,6 +717,35 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 		ctx->csr_mux = csr;
 	}
 
+	of_devid = of_match_device(xgene_ahci_of_match, dev);
+	if (of_devid) {
+		if (of_devid->data)
+			version = (enum xgene_ahci_version) of_devid->data;
+	}
+#ifdef CONFIG_ACPI
+	else {
+		const struct acpi_device_id *acpi_id;
+		struct acpi_device_info *info;
+		acpi_status status;
+
+		acpi_id = acpi_match_device(xgene_ahci_acpi_match, &pdev->dev);
+		if (!acpi_id) {
+			dev_warn(&pdev->dev, "No node entry in ACPI table. Assume version1\n");
+			version = XGENE_AHCI_V1;
+		} else if (acpi_id->driver_data) {
+			version = (enum xgene_ahci_version) acpi_id->driver_data;
+			status = acpi_get_object_info(ACPI_HANDLE(&pdev->dev), &info);
+			if (ACPI_FAILURE(status)) {
+				dev_warn(&pdev->dev, "%s: Error reading device info. Assume version1\n",
+					__func__);
+				version = XGENE_AHCI_V1;
+			}
+			if (info->valid & ACPI_VALID_CID)
+				version = XGENE_AHCI_V2;
+		}
+	}
+#endif
+
 	dev_dbg(dev, "VAddr 0x%p Mmio VAddr 0x%p\n", ctx->csr_core,
 		hpriv->mmio);
 
@@ -704,9 +773,19 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 	/* Configure the host controller */
 	xgene_ahci_hw_init(hpriv);
 skip_clk_phy:
-	hpriv->flags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_NO_NCQ;
 
-	rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info,
+	switch (version) {
+	case XGENE_AHCI_V1:
+		hpriv->flags = AHCI_HFLAG_NO_NCQ;
+		break;
+	case XGENE_AHCI_V2:
+		hpriv->flags |= AHCI_HFLAG_YES_FBS | AHCI_HFLAG_EDGE_IRQ;
+		break;
+	default:
+		break;
+	}
+
+	rc = ahci_platform_init_host(pdev, hpriv, ppi[version - 1],
 				     &ahci_platform_sht);
 	if (rc)
 		goto disable_resources;
@@ -719,20 +798,6 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 	return rc;
 }
 
-#ifdef CONFIG_ACPI
-static const struct acpi_device_id xgene_ahci_acpi_match[] = {
-	{ "APMC0D0D", },
-	{ }
-};
-MODULE_DEVICE_TABLE(acpi, xgene_ahci_acpi_match);
-#endif
-
-static const struct of_device_id xgene_ahci_of_match[] = {
-	{.compatible = "apm,xgene-ahci"},
-	{},
-};
-MODULE_DEVICE_TABLE(of, xgene_ahci_of_match);
-
 static struct platform_driver xgene_ahci_driver = {
 	.probe = xgene_ahci_probe,
 	.remove = ata_platform_remove_one,

drivers/ata/libahci.c

@@ -1825,11 +1825,38 @@ static irqreturn_t ahci_multi_irqs_intr(int irq, void *dev_instance)
 	return IRQ_WAKE_THREAD;
 }
 
-static irqreturn_t ahci_single_irq_intr(int irq, void *dev_instance)
+static u32 ahci_handle_port_intr(struct ata_host *host, u32 irq_masked)
+{
+	unsigned int i, handled = 0;
+
+	for (i = 0; i < host->n_ports; i++) {
+		struct ata_port *ap;
+
+		if (!(irq_masked & (1 << i)))
+			continue;
+
+		ap = host->ports[i];
+		if (ap) {
+			ahci_port_intr(ap);
+			VPRINTK("port %u\n", i);
+		} else {
+			VPRINTK("port %u (no irq)\n", i);
+			if (ata_ratelimit())
+				dev_warn(host->dev,
+					 "interrupt on disabled port %u\n", i);
+		}
+
+		handled = 1;
+	}
+
+	return handled;
+}
+
+static irqreturn_t ahci_single_edge_irq_intr(int irq, void *dev_instance)
 {
 	struct ata_host *host = dev_instance;
 	struct ahci_host_priv *hpriv;
-	unsigned int i, handled = 0;
+	unsigned int rc = 0;
 	void __iomem *mmio;
 	u32 irq_stat, irq_masked;
 
@@ -1847,25 +1874,44 @@ static irqreturn_t ahci_single_irq_intr(int irq, void *dev_instance)
 
 	spin_lock(&host->lock);
 
-	for (i = 0; i < host->n_ports; i++) {
-		struct ata_port *ap;
+	/*
+	 * HOST_IRQ_STAT behaves as edge triggered latch meaning that
+	 * it should be cleared before all the port events are cleared.
+	 */
+	writel(irq_stat, mmio + HOST_IRQ_STAT);
 
-		if (!(irq_masked & (1 << i)))
-			continue;
+	rc = ahci_handle_port_intr(host, irq_masked);
 
-		ap = host->ports[i];
-		if (ap) {
-			ahci_port_intr(ap);
-			VPRINTK("port %u\n", i);
-		} else {
-			VPRINTK("port %u (no irq)\n", i);
-			if (ata_ratelimit())
-				dev_warn(host->dev,
-					 "interrupt on disabled port %u\n", i);
-		}
+	spin_unlock(&host->lock);
 
-		handled = 1;
-	}
+	VPRINTK("EXIT\n");
+
+	return IRQ_RETVAL(rc);
+}
+
+static irqreturn_t ahci_single_level_irq_intr(int irq, void *dev_instance)
+{
+	struct ata_host *host = dev_instance;
+	struct ahci_host_priv *hpriv;
+	unsigned int rc = 0;
+	void __iomem *mmio;
+	u32 irq_stat, irq_masked;
+
+	VPRINTK("ENTER\n");
+
+	hpriv = host->private_data;
+	mmio = hpriv->mmio;
+
+	/* sigh.  0xffffffff is a valid return from h/w */
+	irq_stat = readl(mmio + HOST_IRQ_STAT);
+	if (!irq_stat)
+		return IRQ_NONE;
+
+	irq_masked = irq_stat & hpriv->port_map;
+
+	spin_lock(&host->lock);
+
+	rc = ahci_handle_port_intr(host, irq_masked);
 
 	/* HOST_IRQ_STAT behaves as level triggered latch meaning that
 	 * it should be cleared after all the port events are cleared;
@@ -1882,7 +1928,7 @@ static irqreturn_t ahci_single_irq_intr(int irq, void *dev_instance)
 
 	VPRINTK("EXIT\n");
 
-	return IRQ_RETVAL(handled);
+	return IRQ_RETVAL(rc);
 }
 
 unsigned int ahci_qc_issue(struct ata_queued_cmd *qc)
@@ -2297,7 +2343,7 @@ static int ahci_port_start(struct ata_port *ap)
 	/*
 	 * Switch to per-port locking in case each port has its own MSI vector.
 	 */
-	if ((hpriv->flags & AHCI_HFLAG_MULTI_MSI)) {
+	if (hpriv->flags & AHCI_HFLAG_MULTI_MSI) {
 		spin_lock_init(&pp->lock);
 		ap->lock = &pp->lock;
 	}
@@ -2425,7 +2471,10 @@ static int ahci_host_activate_multi_irqs(struct ata_host *host, int irq,
 	rc = ata_host_start(host);
 	if (rc)
 		return rc;
-
+	/*
+	 * Requests IRQs according to AHCI-1.1 when multiple MSIs were
+	 * allocated. That is one MSI per port, starting from @irq.
+	 */
 	for (i = 0; i < host->n_ports; i++) {
 		struct ahci_port_priv *pp = host->ports[i]->private_data;
 
@@ -2464,29 +2513,27 @@ static int ahci_host_activate_multi_irqs(struct ata_host *host, int irq,
 /**
  *	ahci_host_activate - start AHCI host, request IRQs and register it
  *	@host: target ATA host
- *	@irq: base IRQ number to request
  *	@sht: scsi_host_template to use when registering the host
  *
- *	Similar to ata_host_activate, but requests IRQs according to AHCI-1.1
- *	when multiple MSIs were allocated. That is one MSI per port, starting
- *	from @irq.
- *
  *	LOCKING:
  *	Inherited from calling layer (may sleep).
  *
  *	RETURNS:
  *	0 on success, -errno otherwise.
  */
-int ahci_host_activate(struct ata_host *host, int irq,
-		       struct scsi_host_template *sht)
+int ahci_host_activate(struct ata_host *host, struct scsi_host_template *sht)
 {
 	struct ahci_host_priv *hpriv = host->private_data;
+	int irq = hpriv->irq;
 	int rc;
 
 	if (hpriv->flags & AHCI_HFLAG_MULTI_MSI)
 		rc = ahci_host_activate_multi_irqs(host, irq, sht);
+	else if (hpriv->flags & AHCI_HFLAG_EDGE_IRQ)
+		rc = ata_host_activate(host, irq, ahci_single_edge_irq_intr,
+				       IRQF_SHARED, sht);
 	else
-		rc = ata_host_activate(host, irq, ahci_single_irq_intr,
+		rc = ata_host_activate(host, irq, ahci_single_level_irq_intr,
 				       IRQF_SHARED, sht);
 	return rc;
 }

drivers/ata/libahci_platform.c

@@ -518,6 +518,8 @@ int ahci_platform_init_host(struct platform_device *pdev,
 		return -EINVAL;
 	}
 
+	hpriv->irq = irq;
+
 	/* prepare host */
 	pi.private_data = (void *)(unsigned long)hpriv->flags;
 
@@ -588,7 +590,7 @@ int ahci_platform_init_host(struct platform_device *pdev,
 	ahci_init_controller(host);
 	ahci_print_info(host, "platform");
 
-	return ahci_host_activate(host, irq, sht);
+	return ahci_host_activate(host, sht);
 }
 EXPORT_SYMBOL_GPL(ahci_platform_init_host);
 

drivers/ata/libata-core.c

@@ -3654,7 +3654,7 @@ int sata_link_resume(struct ata_link *link, const unsigned long *params,
  *	EH context.
  *
  *	RETURNS:
- *	0 on succes, -errno otherwise.
+ *	0 on success, -errno otherwise.
  */
 int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
 		      bool spm_wakeup)
@@ -4225,7 +4225,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 	{ "PIONEER DVD-RW  DVR-216D",	NULL,	ATA_HORKAGE_NOSETXFER },
 
 	/* devices that don't properly handle queued TRIM commands */
-	{ "Micron_M500*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
+	{ "Micron_M500_*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
 	{ "Crucial_CT*M500*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
@@ -6456,12 +6456,7 @@ static int __init ata_parse_force_one(char **cur,
 				      struct ata_force_ent *force_ent,
 				      const char **reason)
 {
-	/* FIXME: Currently, there's no way to tag init const data and
-	 * using __initdata causes build failure on some versions of
-	 * gcc.  Once __initdataconst is implemented, add const to the
-	 * following structure.
-	 */
-	static struct ata_force_param force_tbl[] __initdata = {
+	static const struct ata_force_param force_tbl[] __initconst = {
 		{ "40c",	.cbl		= ATA_CBL_PATA40 },
 		{ "80c",	.cbl		= ATA_CBL_PATA80 },
 		{ "short40c",	.cbl		= ATA_CBL_PATA40_SHORT },
@@ -6472,6 +6467,8 @@ static int __init ata_parse_force_one(char **cur,
 		{ "3.0Gbps",	.spd_limit	= 2 },
 		{ "noncq",	.horkage_on	= ATA_HORKAGE_NONCQ },
 		{ "ncq",	.horkage_off	= ATA_HORKAGE_NONCQ },
+		{ "noncqtrim",	.horkage_on	= ATA_HORKAGE_NO_NCQ_TRIM },
+		{ "ncqtrim",	.horkage_off	= ATA_HORKAGE_NO_NCQ_TRIM },
 		{ "dump_id",	.horkage_on	= ATA_HORKAGE_DUMP_ID },
 		{ "pio0",	.xfer_mask	= 1 << (ATA_SHIFT_PIO + 0) },
 		{ "pio1",	.xfer_mask	= 1 << (ATA_SHIFT_PIO + 1) },

drivers/ata/libata-eh.c

@@ -1507,16 +1507,21 @@ unsigned int ata_read_log_page(struct ata_device *dev, u8 log,
 {
 	struct ata_taskfile tf;
 	unsigned int err_mask;
+	bool dma = false;
 
 	DPRINTK("read log page - log 0x%x, page 0x%x\n", log, page);
 
+retry:
 	ata_tf_init(dev, &tf);
-	if (dev->dma_mode && ata_id_has_read_log_dma_ext(dev->id)) {
+	if (dev->dma_mode && ata_id_has_read_log_dma_ext(dev->id) &&
+	    !(dev->horkage & ATA_HORKAGE_NO_NCQ_LOG)) {
 		tf.command = ATA_CMD_READ_LOG_DMA_EXT;
 		tf.protocol = ATA_PROT_DMA;
+		dma = true;
 	} else {
 		tf.command = ATA_CMD_READ_LOG_EXT;
 		tf.protocol = ATA_PROT_PIO;
+		dma = false;
 	}
 	tf.lbal = log;
 	tf.lbam = page;
@@ -1527,6 +1532,12 @@ unsigned int ata_read_log_page(struct ata_device *dev, u8 log,
 	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE,
 				     buf, sectors * ATA_SECT_SIZE, 0);
 
+	if (err_mask && dma) {
+		dev->horkage |= ATA_HORKAGE_NO_NCQ_LOG;
+		ata_dev_warn(dev, "READ LOG DMA EXT failed, trying unqueued\n");
+		goto retry;
+	}
+
 	DPRINTK("EXIT, err_mask=%x\n", err_mask);
 	return err_mask;
 }

drivers/ata/libata-transport.c

@@ -560,6 +560,27 @@ show_ata_dev_gscr(struct device *dev,
 
 static DEVICE_ATTR(gscr, S_IRUGO, show_ata_dev_gscr, NULL);
 
+static ssize_t
+show_ata_dev_trim(struct device *dev,
+		  struct device_attribute *attr, char *buf)
+{
+	struct ata_device *ata_dev = transport_class_to_dev(dev);
+	unsigned char *mode;
+
+	if (!ata_id_has_trim(ata_dev->id))
+		mode = "unsupported";
+	else if (ata_dev->horkage & ATA_HORKAGE_NO_NCQ_TRIM)
+			mode = "forced_unqueued";
+	else if (ata_fpdma_dsm_supported(ata_dev))
+		mode = "queued";
+	else
+		mode = "unqueued";
+
+	return snprintf(buf, 20, "%s\n", mode);
+}
+
+static DEVICE_ATTR(trim, S_IRUGO, show_ata_dev_trim, NULL);
+
 static DECLARE_TRANSPORT_CLASS(ata_dev_class,
 			       "ata_device", NULL, NULL, NULL);
 
@@ -733,6 +754,7 @@ struct scsi_transport_template *ata_attach_transport(void)
 	SETUP_DEV_ATTRIBUTE(ering);
 	SETUP_DEV_ATTRIBUTE(id);
 	SETUP_DEV_ATTRIBUTE(gscr);
+	SETUP_DEV_ATTRIBUTE(trim);
 	BUG_ON(count > ATA_DEV_ATTRS);
 	i->dev_attrs[count] = NULL;
 

drivers/ata/pata_hpt366.c

@@ -352,7 +352,7 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	};
 	const struct ata_port_info *ppi[] = { &info_hpt366, NULL };
 
-	void *hpriv = NULL;
+	const void *hpriv = NULL;
 	u32 reg1;
 	int rc;
 
@@ -383,7 +383,7 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 		break;
 	}
 	/* Now kick off ATA set up */
-	return ata_pci_bmdma_init_one(dev, ppi, &hpt36x_sht, hpriv, 0);
+	return ata_pci_bmdma_init_one(dev, ppi, &hpt36x_sht, (void *)hpriv, 0);
 }
 
 #ifdef CONFIG_PM_SLEEP

drivers/ata/pata_samsung_cf.c

@@ -638,7 +638,7 @@ static const struct dev_pm_ops pata_s3c_pm_ops = {
 #endif
 
 /* driver device registration */
-static struct platform_device_id pata_s3c_driver_ids[] = {
+static const struct platform_device_id pata_s3c_driver_ids[] = {
 	{
 		.name		= "s3c64xx-pata",
 		.driver_data	= TYPE_S3C64XX,

drivers/ata/sata_highbank.c

@@ -499,6 +499,7 @@ static int ahci_highbank_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
+	hpriv->irq = irq;
 	hpriv->flags |= (unsigned long)pi.private_data;
 
 	hpriv->mmio = devm_ioremap(dev, mem->start, resource_size(mem));
@@ -568,7 +569,7 @@ static int ahci_highbank_probe(struct platform_device *pdev)
 	ahci_init_controller(host);
 	ahci_print_info(host, "platform");
 
-	rc = ahci_host_activate(host, irq, &ahci_highbank_platform_sht);
+	rc = ahci_host_activate(host, &ahci_highbank_platform_sht);
 	if (rc)
 		goto err0;
 

drivers/ata/sata_nv.c

@@ -599,7 +599,7 @@ MODULE_DEVICE_TABLE(pci, nv_pci_tbl);
 MODULE_VERSION(DRV_VERSION);
 
 static bool adma_enabled;
-static bool swncq_enabled = 1;
+static bool swncq_enabled = true;
 static bool msi_enabled;
 
 static void nv_adma_register_mode(struct ata_port *ap)

include/linux/ata.h

@@ -704,9 +704,19 @@ static inline bool ata_id_wcache_enabled(const u16 *id)
 
 static inline bool ata_id_has_read_log_dma_ext(const u16 *id)
 {
+	/* Word 86 must have bit 15 set */
 	if (!(id[ATA_ID_CFS_ENABLE_2] & (1 << 15)))
 		return false;
-	return id[ATA_ID_COMMAND_SET_3] & (1 << 3);
+
+	/* READ LOG DMA EXT support can be signaled either from word 119
+	 * or from word 120. The format is the same for both words: Bit
+	 * 15 must be cleared, bit 14 set and bit 3 set.
+	 */
+	if ((id[ATA_ID_COMMAND_SET_3] & 0xC008) == 0x4008 ||
+	    (id[ATA_ID_COMMAND_SET_4] & 0xC008) == 0x4008)
+		return true;
+
+	return false;
 }
 
 static inline bool ata_id_has_sense_reporting(const u16 *id)

include/linux/libata.h

@@ -430,6 +430,7 @@ enum {
 	ATA_HORKAGE_NOLPM	= (1 << 20),	/* don't use LPM */
 	ATA_HORKAGE_WD_BROKEN_LPM = (1 << 21),	/* some WDs have broken LPM */
 	ATA_HORKAGE_ZERO_AFTER_TRIM = (1 << 22),/* guarantees zero after trim */
+	ATA_HORKAGE_NO_NCQ_LOG	= (1 << 23),	/* don't use NCQ for log read */
 
 	 /* DMA mask for user DMA control: User visible values; DO NOT
 	    renumber */