[ARM] 4979/1: [AT91] Olimex SAM9-L9260 board support

Support for the Olimex SAM9-L9260 board.
 <http://www.olimex.com/dev/sam9-L9260.html>

Original patch from Ivan Vasilev.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-at91/Kconfig

@@ -140,6 +140,13 @@ config MACH_CAM60
 	  Select this if you are using KwikByte's KB9260 (CAM60) board based on the Atmel AT91SAM9260.
 	  <http://www.kwikbyte.com/KB9260.html>
 
+config MACH_SAM9_L9260
+	bool "Olimex SAM9-L9260 board"
+	depends on ARCH_AT91SAM9260
+	help
+	  Select this if you are using Olimex's SAM9-L9260 board based on the Atmel AT91SAM9260.
+	  <http://www.olimex.com/dev/sam9-L9260.html>
+
 endif
 
 # ----------------------------------------------------------
@@ -223,7 +230,7 @@ comment "AT91 Board Options"
 
 config MTD_AT91_DATAFLASH_CARD
 	bool "Enable DataFlash Card support"
-	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK)
+	depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK || MACH_SAM9_L9260)
 	help
 	  Enable support for the DataFlash card.
 

arch/arm/mach-at91/Makefile

@@ -33,6 +33,7 @@ obj-$(CONFIG_MACH_PICOTUX2XX)	+= board-picotux200.o
 # AT91SAM9260 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
 obj-$(CONFIG_MACH_CAM60)	+= board-cam60.o
+obj-$(CONFIG_MACH_SAM9_L9260)	+= board-sam9-l9260.o
 
 # AT91SAM9261 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o

arch/arm/mach-at91/board-sam9-l9260.c

+/*
+ * linux/arch/arm/mach-at91/board-sam9-l9260.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2006 Atmel
+ *  Copyright (C) 2007 Olimex Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91sam9260_initialize(18432000);
+
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
+
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+	at91sam9260_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PC5,
+	.pullup_pin	= 0,		/* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 1,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#endif
+#endif
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata ek_macb_data = {
+	.phy_irq_pin	= AT91_PIN_PA7,
+	.is_rmii	= 0,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+	{
+		.name	= "Bootloader Area",
+		.offset	= 0,
+		.size	= 10 * 1024 * 1024,
+	},
+	{
+		.name	= "User Area",
+		.offset	= 10 * 1024 * 1024,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(ek_nand_partition);
+	return ek_nand_partition;
+}
+
+static struct at91_nand_data __initdata ek_nand_data = {
+	.ale		= 21,
+	.cle		= 22,
+//	.det_pin	= ... not connected
+	.rdy_pin	= AT91_PIN_PC13,
+	.enable_pin	= AT91_PIN_PC14,
+	.partition_info	= nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+	.bus_width_16	= 1,
+#else
+	.bus_width_16	= 0,
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+	.slot_b		= 1,
+	.wire4		= 1,
+	.det_pin	= AT91_PIN_PC8,
+	.wp_pin		= AT91_PIN_PC4,
+//	.vcc_pin	= ... not connected
+};
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* USB Host */
+	at91_add_device_usbh(&ek_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&ek_udc_data);
+	/* SPI */
+	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+	/* NAND */
+	at91_add_device_nand(&ek_nand_data);
+	/* Ethernet */
+	at91_add_device_eth(&ek_macb_data);
+	/* MMC */
+	at91_add_device_mmc(0, &ek_mmc_data);
+	/* I2C */
+	at91_add_device_i2c(NULL, 0);
+}
+
+MACHINE_START(SAM9_L9260, "Olimex SAM9-L9260")
+	/* Maintainer: Olimex */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END