[POWERPC] 4xx: Base support for 440GX Taishan eval board

This patch adds base support for the AMCC Taishan 440GX evaluation
board.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

arch/powerpc/Kconfig.debug

@@ -225,7 +225,8 @@ config PPC_EARLY_DEBUG_44x
 	depends on 44x
 	help
 	  Select this to enable early debugging for IBM 44x chips via the
-	  inbuilt serial port.
+	  inbuilt serial port.  If you enable this, ensure you set
+          PPC_EARLY_DEBUG_44x_PHYSLOW below to suit your target board.
 
 config PPC_EARLY_DEBUG_40x
 	bool "Early serial debugging for IBM/AMCC 40x CPUs"
@@ -250,6 +251,9 @@ config PPC_EARLY_DEBUG_44x_PHYSLOW
 	hex "Low 32 bits of early debug UART physical address"
 	depends on PPC_EARLY_DEBUG_44x
 	default "0x40000200"
+	help
+	  You probably want 0x40000200 for ebony boards and
+          0x40000300 for taishan
 
 config PPC_EARLY_DEBUG_44x_PHYSHIGH
 	hex "EPRN of early debug UART physical address"

arch/powerpc/boot/Makefile

@@ -37,8 +37,10 @@ BOOTCFLAGS	+= -I$(obj) -I$(srctree)/$(obj) -I$(srctree)/$(src)/libfdt
 
 $(obj)/4xx.o: BOOTCFLAGS += -mcpu=440
 $(obj)/ebony.o: BOOTCFLAGS += -mcpu=440
+$(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=440
 $(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
 
+
 zlib       := inffast.c inflate.c inftrees.c
 zlibheader := inffast.h inffixed.h inflate.h inftrees.h infutil.h
 zliblinuxheader := zlib.h zconf.h zutil.h
@@ -58,7 +60,7 @@ src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
 		cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
 		ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
 		cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c \
-		fixed-head.S ep88xc.c cuboot-hpc2.c ep405.c
+		fixed-head.S ep88xc.c cuboot-hpc2.c ep405.c cuboot-taishan.c
 src-boot := $(src-wlib) $(src-plat) empty.c
 
 src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -199,6 +201,7 @@ image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
 image-$(CONFIG_BAMBOO)			+= treeImage.bamboo cuImage.bamboo
 image-$(CONFIG_SEQUOIA)			+= cuImage.sequoia
 image-$(CONFIG_WALNUT)			+= treeImage.walnut
+image-$(CONFIG_TAISHAN)			+= cuImage.taishan
 endif
 
 # For 32-bit powermacs, build the COFF and miboot images

arch/powerpc/boot/cuboot-taishan.c

+/*
+ * Old U-boot compatibility for Taishan
+ *
+ * Author: Hugh Blemings <hugh@au.ibm.com>
+ *
+ * Copyright 2007 Hugh Blemings, IBM Corporation.
+ *   Based on cuboot-ebony.c which is:
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *   Based on cuboot-83xx.c, which is:
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "cuboot.h"
+#include "reg.h"
+#include "dcr.h"
+#include "4xx.h"
+
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+BSS_STACK(4096);
+
+static void taishan_fixups(void)
+{
+	/* FIXME: sysclk should be derived by reading the FPGA
+	   registers */
+	unsigned long sysclk = 33000000;
+
+	/* 440EP Clock logic is all but identical to 440GX
+	   so we just use that code for now at least */
+	ibm440ep_fixup_clocks(sysclk, 6 * 1843200);
+
+	ibm4xx_fixup_memsize();
+
+	dt_fixup_mac_addresses(bd.bi_enetaddr, bd.bi_enet1addr);
+
+	ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+		   unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+
+	platform_ops.fixups = taishan_fixups;
+	fdt_init(_dtb_start);
+	serial_console_init();
+}

arch/powerpc/boot/dts/taishan.dts

+/*
+ * Device Tree Source for IBM/AMCC Taishan
+ *
+ * Copyright 2007 IBM Corp.
+ * Hugh Blemings <hugh@au.ibm.com> based off code by
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>, David Gibson <dwg@au1.ibm.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	model = "amcc,taishan";
+	compatible = "amcc,taishan";
+	dcr-parent = <&/cpus/PowerPC,440GX@0>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,440GX@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <2FAF0800>; // 800MHz
+			timebase-frequency = <0>; // Filled in by zImage
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <8000>; /* 32 kB */
+			d-cache-size = <8000>; /* 32 kB */
+			dcr-controller;
+			dcr-access-method = "native";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0 0>; // Filled in by zImage
+	};
+
+
+	UICB0: interrupt-controller-base {
+		compatible = "ibm,uic-440gx", "ibm,uic";
+		interrupt-controller;
+		cell-index = <3>;
+		dcr-reg = <200 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+	};
+
+
+	UIC0: interrupt-controller0 {
+		compatible = "ibm,uic-440gx", "ibm,uic";
+		interrupt-controller;
+		cell-index = <0>;
+		dcr-reg = <0c0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <01 4 00 4>; /* cascade - first non-critical */
+		interrupt-parent = <&UICB0>;
+
+	};
+
+	UIC1: interrupt-controller1 {
+		compatible = "ibm,uic-440gx", "ibm,uic";
+		interrupt-controller;
+		cell-index = <1>;
+		dcr-reg = <0d0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <03 4 02 4>; /* cascade */
+		interrupt-parent = <&UICB0>;
+	};
+
+	UIC2: interrupt-controller2 {
+		compatible = "ibm,uic-440gx", "ibm,uic";
+		interrupt-controller;
+		cell-index = <2>; /* was 1 */
+		dcr-reg = <210 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <05 4 04 4>; /* cascade */
+		interrupt-parent = <&UICB0>;
+	};
+
+
+	CPC0: cpc {
+		compatible = "ibm,cpc-440gp";
+		dcr-reg = <0b0 003 0e0 010>;
+		// FIXME: anything else?
+	};
+
+	plb {
+		compatible = "ibm,plb-440gx", "ibm,plb4";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+		clock-frequency = <9896800>; // 160MHz
+
+		SDRAM0: memory-controller {
+			compatible = "ibm,sdram-440gp";
+			dcr-reg = <010 2>;
+			// FIXME: anything else?
+		};
+
+		SRAM0: sram {
+			compatible = "ibm,sram-440gp";
+			dcr-reg = <020 8 00a 1>;
+		};
+
+		DMA0: dma {
+			// FIXME: ???
+			compatible = "ibm,dma-440gp";
+			dcr-reg = <100 027>;
+		};
+
+		MAL0: mcmal {
+			compatible = "ibm,mcmal-440gx", "ibm,mcmal2";
+			dcr-reg = <180 62>;
+			num-tx-chans = <4>;
+			num-rx-chans = <4>;
+			interrupt-parent = <&MAL0>;
+			interrupts = <0 1 2 3 4>;
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
+					 /*RXEOB*/ 1 &UIC0 b 4
+					 /*SERR*/  2 &UIC1 0 4
+					 /*TXDE*/  3 &UIC1 1 4
+					 /*RXDE*/  4 &UIC1 2 4>;
+			interrupt-map-mask = <ffffffff>;
+		};
+
+		POB0: opb {
+			compatible = "ibm,opb-440gx", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* Wish there was a nicer way of specifying a full 32-bit
+			   range */
+			ranges = <00000000 1 00000000 80000000
+				  80000000 1 80000000 80000000>;
+			dcr-reg = <090 00b>;
+			interrupt-parent = <&UIC1>;
+			interrupts = <7 4>;
+			clock-frequency = <4C4B400>; // 80MHz
+
+
+			EBC0: ebc {
+				compatible = "ibm,ebc-440gx", "ibm,ebc";
+				dcr-reg = <012 2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				clock-frequency = <4C4B400>; // 80MHz
+
+				/* ranges property is supplied by zImage
+				 * based on firmware's configuration of the
+				 * EBC bridge */
+
+				interrupts = <5 4>;
+				interrupt-parent = <&UIC1>;
+
+				/* TODO: Add other EBC devices */
+			};
+
+
+
+			UART0: serial@40000200 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <40000200 8>;
+				virtual-reg = <e0000200>;
+ 				clock-frequency = <A8C000>;
+				current-speed = <1C200>; /* 115200 */
+				interrupt-parent = <&UIC0>;
+				interrupts = <0 4>;
+			};
+
+			UART1: serial@40000300 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <40000300 8>;
+				virtual-reg = <e0000300>;
+				clock-frequency = <A8C000>;
+				current-speed = <1C200>; /* 115200 */
+				interrupt-parent = <&UIC0>;
+				interrupts = <1 4>;
+			};
+
+			IIC0: i2c@40000400 {
+				/* FIXME */
+				device_type = "i2c";
+				compatible = "ibm,iic-440gp", "ibm,iic";
+				reg = <40000400 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <2 4>;
+			};
+			IIC1: i2c@40000500 {
+				/* FIXME */
+				device_type = "i2c";
+				compatible = "ibm,iic-440gp", "ibm,iic";
+				reg = <40000500 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <3 4>;
+			};
+
+			GPIO0: gpio@40000700 {
+				/* FIXME */
+				compatible = "ibm,gpio-440gp";
+				reg = <40000700 20>;
+			};
+
+			ZMII0: emac-zmii@40000780 {
+				device_type = "zgmii-interface";
+				compatible = "ibm,zmii-440gx", "ibm,zmii";
+				reg = <40000780 c>;
+			};
+
+			RGMII0: emac-rgmii@40000790 {
+				device_type = "rgmii-interface";
+				compatible = "ibm,rgmii";
+				reg = <40000790 8>;
+			};
+
+
+			EMAC0: ethernet@40000800 {
+				unused = <1>;
+				linux,network-index = <2>;
+				device_type = "network";
+				compatible = "ibm,emac-440gx", "ibm,emac4";
+				interrupt-parent = <&UIC1>;
+				interrupts = <1c 4 1d 4>;
+				reg = <40000800 70>;
+				local-mac-address = [000000000000]; // Filled in by zImage
+				mal-device = <&MAL0>;
+				mal-tx-channel = <0>;
+				mal-rx-channel = <0>;
+				cell-index = <0>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <0>;
+			};
+		 	EMAC1: ethernet@40000900 {
+				unused = <1>;
+				linux,network-index = <3>;
+				device_type = "network";
+				compatible = "ibm,emac-440gx", "ibm,emac4";
+				interrupt-parent = <&UIC1>;
+				interrupts = <1e 4 1f 4>;
+				reg = <40000900 70>;
+				local-mac-address = [000000000000]; // Filled in by zImage
+				mal-device = <&MAL0>;
+				mal-tx-channel = <1>;
+				mal-rx-channel = <1>;
+				cell-index = <1>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+ 				zmii-device = <&ZMII0>;
+				zmii-channel = <1>;
+			};
+
+		 	EMAC2: ethernet@40000c00 {
+				linux,network-index = <0>;
+				device_type = "network";
+				compatible = "ibm,emac-440gx", "ibm,emac4";
+				interrupt-parent = <&UIC2>;
+				interrupts = <0 4 1 4>;
+				reg = <40000c00 70>;
+				local-mac-address = [000000000000]; // Filled in by zImage
+				mal-device = <&MAL0>;
+				mal-tx-channel = <2>;
+				mal-rx-channel = <2>;
+				cell-index = <2>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rgmii";
+				phy-map = <00000001>;
+				rgmii-device = <&RGMII0>;
+				rgmii-channel = <0>;
+ 				zmii-device = <&ZMII0>;
+				zmii-channel = <2>;
+			};
+
+		 	EMAC3: ethernet@40000e00 {
+				linux,network-index = <1>;
+				device_type = "network";
+				compatible = "ibm,emac-440gx", "ibm,emac4";
+				interrupt-parent = <&UIC2>;
+				interrupts = <2 4 3 4>;
+				reg = <40000e00 70>;
+				local-mac-address = [000000000000]; // Filled in by zImage
+				mal-device = <&MAL0>;
+				mal-tx-channel = <3>;
+				mal-rx-channel = <3>;
+				cell-index = <3>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rgmii";
+				phy-map = <00000003>;
+				rgmii-device = <&RGMII0>;
+				rgmii-channel = <1>;
+ 				zmii-device = <&ZMII0>;
+				zmii-channel = <3>;
+			};
+
+
+			GPT0: gpt@40000a00 {
+				/* FIXME */
+				reg = <40000a00 d4>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <12 4 13 4 14 4 15 4 16 4>;
+			};
+
+		};
+
+		PCIX0: pci@20ec00000 {
+			device_type = "pci";
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			compatible = "ibm,plb440gp-pcix", "ibm,plb-pcix";
+			primary;
+			large-inbound-windows;
+			enable-msi-hole;
+			reg = <2 0ec00000   8	/* Config space access */
+			       0 0 0		/* no IACK cycles */
+			       2 0ed00000   4   /* Special cycles */
+			       2 0ec80000 100	/* Internal registers */
+			       2 0ec80100  fc>;	/* Internal messaging registers */
+
+			/* Outbound ranges, one memory and one IO,
+			 * later cannot be changed
+			 */
+			ranges = <02000000 0 80000000 00000003 80000000 0 80000000
+				  01000000 0 00000000 00000002 08000000 0 00010000>;
+
+			/* Inbound 2GB range starting at 0 */
+			dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+			interrupt-map-mask = <f800 0 0 7>;
+			interrupt-map = <
+				/* IDSEL 1 */
+				0800 0 0 1 &UIC0 17 8
+				0800 0 0 2 &UIC0 18 8
+				0800 0 0 3 &UIC0 19 8
+				0800 0 0 4 &UIC0 1a 8
+
+				/* IDSEL 2 */
+				1000 0 0 1 &UIC0 18 8
+				1000 0 0 2 &UIC0 19 8
+				1000 0 0 3 &UIC0 1a 8
+				1000 0 0 4 &UIC0 17 8
+			>;
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/plb/opb/serial@40000300";
+	};
+};

arch/powerpc/configs/taishan_defconfig

+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.24-rc4
+# Tue Dec 11 16:44:44 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+CONFIG_44x=y
+# CONFIG_E200 is not set
+CONFIG_4xx=y
+CONFIG_BOOKE=y
+CONFIG_PTE_64BIT=y
+CONFIG_PHYS_64BIT=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_PPC_DCR_NATIVE=y
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_PPC_DCR=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+# CONFIG_PPC4xx_PCI_EXPRESS is not set
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_BAMBOO is not set
+# CONFIG_EBONY is not set
+# CONFIG_SEQUOIA is not set
+CONFIG_TAISHAN=y
+CONFIG_440GX=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE=""
+CONFIG_SECCOMP=y
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="taishan.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
+# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x01000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+CONFIG_CONNECTOR=y
+CONFIG_PROC_EVENTS=y
+# CONFIG_MTD is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=35000
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_XILINX_SYSACE is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+CONFIG_MACINTOSH_DRIVERS=y
+# CONFIG_MAC_EMUMOUSEBTN is not set
+# CONFIG_WINDFARM is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_IP1000 is not set
+# CONFIG_ARCNET is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+# CONFIG_MII is not set
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_IBM_NEW_EMAC=y
+CONFIG_IBM_NEW_EMAC_RXB=128
+CONFIG_IBM_NEW_EMAC_TXB=64
+CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
+# CONFIG_IBM_NEW_EMAC_DEBUG is not set
+CONFIG_IBM_NEW_EMAC_ZMII=y
+CONFIG_IBM_NEW_EMAC_RGMII=y
+CONFIG_IBM_NEW_EMAC_TAH=y
+CONFIG_IBM_NEW_EMAC_EMAC4=y
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=m
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_INSTRUMENTATION=y
+# CONFIG_PROFILING is not set
+# CONFIG_KPROBES is not set
+# CONFIG_MARKERS is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+CONFIG_DEBUGGER=y
+# CONFIG_KGDB is not set
+# CONFIG_XMON is not set
+# CONFIG_BDI_SWITCH is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_PPC_CLOCK is not set

arch/powerpc/platforms/44x/Kconfig

@@ -23,6 +23,16 @@ config SEQUOIA
 	help
 	  This option enables support for the AMCC PPC440EPX evaluation board.
 
+config TAISHAN
+	bool "Taishan"
+	depends on 44x
+	default n
+	select 440GX
+	select PCI
+	help
+	  This option enables support for the AMCC PPC440GX "Taishan"
+	  evaluation board.
+
 #config LUAN
 #	bool "Luan"
 #	depends on 44x
@@ -59,6 +69,10 @@ config 440GP
 
 config 440GX
 	bool
+        select IBM_NEW_EMAC_EMAC4
+	select IBM_NEW_EMAC_RGMII
+        select IBM_NEW_EMAC_ZMII #test only
+        select IBM_NEW_EMAC_TAH  #test only
 
 config 440SP
 	bool

arch/powerpc/platforms/44x/Makefile

 obj-$(CONFIG_44x)	:= misc_44x.o
 obj-$(CONFIG_EBONY)	+= ebony.o
+obj-$(CONFIG_TAISHAN)	+= taishan.o
 obj-$(CONFIG_BAMBOO) += bamboo.o
 obj-$(CONFIG_SEQUOIA)	+= sequoia.o

arch/powerpc/platforms/44x/taishan.c

+/*
+ * Taishan board specific routines based off ebony.c code
+ * original copyrights below
+ *
+ * Matt Porter <mporter@kernel.crashing.org>
+ * Copyright 2002-2005 MontaVista Software Inc.
+ *
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ * Copyright (c) 2003-2005 Zultys Technologies
+ *
+ * Rewritten and ported to the merged powerpc tree:
+ * Copyright 2007 David Gibson <dwg@au1.ibm.com>, IBM Corporation.
+ *
+ * Modified from ebony.c for taishan:
+ * Copyright 2007 Hugh Blemings <hugh@au.ibm.com>, IBM Corporation.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/of_platform.h>
+
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/time.h>
+#include <asm/uic.h>
+#include <asm/pci-bridge.h>
+
+#include "44x.h"
+
+static struct of_device_id taishan_of_bus[] = {
+	{ .compatible = "ibm,plb4", },
+	{ .compatible = "ibm,opb", },
+	{ .compatible = "ibm,ebc", },
+	{},
+};
+
+static int __init taishan_device_probe(void)
+{
+	if (!machine_is(taishan))
+		return 0;
+
+	of_platform_bus_probe(NULL, taishan_of_bus, NULL);
+
+	return 0;
+}
+device_initcall(taishan_device_probe);
+
+/*
+ * Called very early, MMU is off, device-tree isn't unflattened
+ */
+static int __init taishan_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+
+	if (!of_flat_dt_is_compatible(root, "amcc,taishan"))
+		return 0;
+
+	return 1;
+}
+
+define_machine(taishan) {
+	.name			= "Taishan",
+	.probe			= taishan_probe,
+	.progress		= udbg_progress,
+	.init_IRQ		= uic_init_tree,
+	.get_irq		= uic_get_irq,
+	.restart		= ppc44x_reset_system,
+	.calibrate_decr		= generic_calibrate_decr,
+};