drivers: thermal: Move QCOM_SPMI_TEMP_ALARM into the qcom subdir

This cleans up the directory a bit allowing just one place to look for
thermal related drivers for QCOM platforms instead of being scattered in
the root directory and the qcom/ subdirectory. Compile-tested with
ARCH=arm64 defconfig and the driver explicitly enabled with menuconfig.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>

drivers/thermal/Kconfig

@@ -374,17 +374,6 @@ config TANGO_THERMAL
 
 source "drivers/thermal/tegra/Kconfig"
 
-config QCOM_SPMI_TEMP_ALARM
-	tristate "Qualcomm SPMI PMIC Temperature Alarm"
-	depends on OF && SPMI && IIO
-	select REGMAP_SPMI
-	help
-	  This enables a thermal sysfs driver for Qualcomm plug-and-play (QPNP)
-	  PMIC devices. It shows up in sysfs as a thermal sensor with multiple
-	  trip points. The temperature reported by the thermal sensor reflects the
-	  real time die temperature if an ADC is present or an estimate of the
-	  temperature based upon the over temperature stage value.
-
 config GENERIC_ADC_THERMAL
 	tristate "Generic ADC based thermal sensor"
 	depends on IIO

drivers/thermal/Makefile

@@ -29,7 +29,6 @@ thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o
 
 # platform thermal drivers
 obj-y				+= broadcom/
-obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM)	+= qcom-spmi-temp-alarm.o
 obj-$(CONFIG_SPEAR_THERMAL)	+= spear_thermal.o
 obj-$(CONFIG_ROCKCHIP_THERMAL)	+= rockchip_thermal.o
 obj-$(CONFIG_RCAR_THERMAL)	+= rcar_thermal.o

drivers/thermal/qcom/Kconfig

@@ -9,3 +9,14 @@ config QCOM_TSENS
 	  thermal zone device via the mode file results in disabling the sensor.
 	  Also able to set threshold temperature for both hot and cold and update
 	  when a threshold is reached.
+
+config QCOM_SPMI_TEMP_ALARM
+	tristate "Qualcomm SPMI PMIC Temperature Alarm"
+	depends on OF && SPMI && IIO
+	select REGMAP_SPMI
+	help
+	  This enables a thermal sysfs driver for Qualcomm plug-and-play (QPNP)
+	  PMIC devices. It shows up in sysfs as a thermal sensor with multiple
+	  trip points. The temperature reported by the thermal sensor reflects the
+	  real time die temperature if an ADC is present or an estimate of the
+	  temperature based upon the over temperature stage value.

drivers/thermal/qcom/Makefile

 obj-$(CONFIG_QCOM_TSENS)	+= qcom_tsens.o
 qcom_tsens-y			+= tsens.o tsens-common.o tsens-8916.o tsens-8974.o tsens-8960.o tsens-v2.o
+obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM)	+= qcom-spmi-temp-alarm.o

drivers/thermal/qcom-spmi-temp-alarm.c → drivers/thermal/qcom/qcom-spmi-temp-alarm.c

@@ -23,7 +23,7 @@
 #include <linux/regmap.h>
 #include <linux/thermal.h>
 
-#include "thermal_core.h"
+#include "../thermal_core.h"
 
 #define QPNP_TM_REG_TYPE		0x04
 #define QPNP_TM_REG_SUBTYPE		0x05