Merge v3.6-rc3 into 'char-misc-next'

This resolves a conflict in:
	drivers/misc/mei/interrupt.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/devicetree/bindings/w1/w1-gpio.txt

+w1-gpio devicetree bindings
+
+Required properties:
+
+ - compatible: "w1-gpio"
+ - gpios: one or two GPIO specs:
+		- the first one is used as data I/O pin
+		- the second one is optional. If specified, it is used as
+		  enable pin for an external pin pullup.
+
+Optional properties:
+
+ - linux,open-drain: if specified, the data pin is considered in
+		     open-drain mode.
+
+Examples:
+
+	onewire@0 {
+		compatible = "w1-gpio";
+		gpios = <&gpio 126 0>, <&gpio 105 0>;
+	};
+

drivers/char/tlclk.c

@@ -784,8 +784,10 @@ static int __init tlclk_init(void)
 	}
 	tlclk_major = ret;
 	alarm_events = kzalloc( sizeof(struct tlclk_alarms), GFP_KERNEL);
-	if (!alarm_events)
+	if (!alarm_events) {
+		ret = -ENOMEM;
 		goto out1;
+	}
 
 	/* Read telecom clock IRQ number (Set by BIOS) */
 	if (!request_region(TLCLK_BASE, 8, "telco_clock")) {

drivers/misc/bmp085-i2c.c

@@ -57,12 +57,6 @@ static int bmp085_i2c_remove(struct i2c_client *client)
 	return bmp085_remove(&client->dev);
 }
 
-static const struct of_device_id bmp085_of_match[] = {
-	{ .compatible = "bosch,bmp085", },
-	{ },
-};
-MODULE_DEVICE_TABLE(of, bmp085_of_match);
-
 static const struct i2c_device_id bmp085_id[] = {
 	{ BMP085_NAME, 0 },
 	{ "bmp180", 0 },
@@ -74,7 +68,6 @@ static struct i2c_driver bmp085_i2c_driver = {
 	.driver = {
 		.owner	= THIS_MODULE,
 		.name	= BMP085_NAME,
-		.of_match_table = bmp085_of_match
 	},
 	.id_table	= bmp085_id,
 	.probe		= bmp085_i2c_probe,

drivers/misc/carma/carma-fpga-program.c

@@ -978,7 +978,6 @@ static int fpga_of_probe(struct platform_device *op)
 	dev_set_drvdata(priv->dev, priv);
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_MEMCPY, mask);
-	dma_cap_set(DMA_INTERRUPT, mask);
 	dma_cap_set(DMA_SLAVE, mask);
 	dma_cap_set(DMA_SG, mask);
 

drivers/misc/carma/carma-fpga.c

@@ -666,7 +666,7 @@ static int data_submit_dma(struct fpga_device *priv, struct data_buf *buf)
 	src = SYS_FPGA_BLOCK;
 	tx = chan->device->device_prep_dma_memcpy(chan, dst, src,
 						  REG_BLOCK_SIZE,
-						  DMA_PREP_INTERRUPT);
+						  0);
 	if (!tx) {
 		dev_err(priv->dev, "unable to prep SYS-FPGA DMA\n");
 		return -ENOMEM;

drivers/misc/mei/hw.h

@@ -40,46 +40,45 @@
 /*
  * MEI device IDs
  */
-#define    MEI_DEV_ID_82946GZ	0x2974  /* 82946GZ/GL */
-#define    MEI_DEV_ID_82G35	0x2984  /* 82G35 Express */
-#define    MEI_DEV_ID_82Q965	0x2994  /* 82Q963/Q965 */
-#define    MEI_DEV_ID_82G965	0x29A4  /* 82P965/G965 */
-
-#define    MEI_DEV_ID_82GM965	0x2A04  /* Mobile PM965/GM965 */
-#define    MEI_DEV_ID_82GME965	0x2A14  /* Mobile GME965/GLE960 */
-
-#define    MEI_DEV_ID_ICH9_82Q35 0x29B4  /* 82Q35 Express */
-#define    MEI_DEV_ID_ICH9_82G33 0x29C4  /* 82G33/G31/P35/P31 Express */
-#define    MEI_DEV_ID_ICH9_82Q33 0x29D4  /* 82Q33 Express */
-#define    MEI_DEV_ID_ICH9_82X38 0x29E4  /* 82X38/X48 Express */
-#define    MEI_DEV_ID_ICH9_3200  0x29F4  /* 3200/3210 Server */
-
-#define    MEI_DEV_ID_ICH9_6	0x28B4  /* Bearlake */
-#define    MEI_DEV_ID_ICH9_7	0x28C4  /* Bearlake */
-#define    MEI_DEV_ID_ICH9_8	0x28D4  /* Bearlake */
-#define    MEI_DEV_ID_ICH9_9    0x28E4  /* Bearlake */
-#define    MEI_DEV_ID_ICH9_10	0x28F4  /* Bearlake */
-
-#define    MEI_DEV_ID_ICH9M_1	0x2A44  /* Cantiga */
-#define    MEI_DEV_ID_ICH9M_2	0x2A54  /* Cantiga */
-#define    MEI_DEV_ID_ICH9M_3	0x2A64  /* Cantiga */
-#define    MEI_DEV_ID_ICH9M_4	0x2A74  /* Cantiga */
-
-#define    MEI_DEV_ID_ICH10_1	0x2E04  /* Eaglelake */
-#define    MEI_DEV_ID_ICH10_2	0x2E14  /* Eaglelake */
-#define    MEI_DEV_ID_ICH10_3	0x2E24  /* Eaglelake */
-#define    MEI_DEV_ID_ICH10_4	0x2E34  /* Eaglelake */
-
-#define    MEI_DEV_ID_IBXPK_1	0x3B64  /* Calpella */
-#define    MEI_DEV_ID_IBXPK_2	0x3B65  /* Calpella */
-
-#define    MEI_DEV_ID_CPT_1	0x1C3A    /* Cougerpoint */
-#define    MEI_DEV_ID_PBG_1	0x1D3A    /* PBG */
-
-#define    MEI_DEV_ID_PPT_1	0x1E3A    /* Pantherpoint PPT */
-#define    MEI_DEV_ID_PPT_2	0x1CBA    /* Pantherpoint PPT */
-#define    MEI_DEV_ID_PPT_3	0x1DBA    /* Pantherpoint PPT */
-
+#define MEI_DEV_ID_82946GZ    0x2974  /* 82946GZ/GL */
+#define MEI_DEV_ID_82G35      0x2984  /* 82G35 Express */
+#define MEI_DEV_ID_82Q965     0x2994  /* 82Q963/Q965 */
+#define MEI_DEV_ID_82G965     0x29A4  /* 82P965/G965 */
+
+#define MEI_DEV_ID_82GM965    0x2A04  /* Mobile PM965/GM965 */
+#define MEI_DEV_ID_82GME965   0x2A14  /* Mobile GME965/GLE960 */
+
+#define MEI_DEV_ID_ICH9_82Q35 0x29B4  /* 82Q35 Express */
+#define MEI_DEV_ID_ICH9_82G33 0x29C4  /* 82G33/G31/P35/P31 Express */
+#define MEI_DEV_ID_ICH9_82Q33 0x29D4  /* 82Q33 Express */
+#define MEI_DEV_ID_ICH9_82X38 0x29E4  /* 82X38/X48 Express */
+#define MEI_DEV_ID_ICH9_3200  0x29F4  /* 3200/3210 Server */
+
+#define MEI_DEV_ID_ICH9_6     0x28B4  /* Bearlake */
+#define MEI_DEV_ID_ICH9_7     0x28C4  /* Bearlake */
+#define MEI_DEV_ID_ICH9_8     0x28D4  /* Bearlake */
+#define MEI_DEV_ID_ICH9_9     0x28E4  /* Bearlake */
+#define MEI_DEV_ID_ICH9_10    0x28F4  /* Bearlake */
+
+#define MEI_DEV_ID_ICH9M_1    0x2A44  /* Cantiga */
+#define MEI_DEV_ID_ICH9M_2    0x2A54  /* Cantiga */
+#define MEI_DEV_ID_ICH9M_3    0x2A64  /* Cantiga */
+#define MEI_DEV_ID_ICH9M_4    0x2A74  /* Cantiga */
+
+#define MEI_DEV_ID_ICH10_1    0x2E04  /* Eaglelake */
+#define MEI_DEV_ID_ICH10_2    0x2E14  /* Eaglelake */
+#define MEI_DEV_ID_ICH10_3    0x2E24  /* Eaglelake */
+#define MEI_DEV_ID_ICH10_4    0x2E34  /* Eaglelake */
+
+#define MEI_DEV_ID_IBXPK_1    0x3B64  /* Calpella */
+#define MEI_DEV_ID_IBXPK_2    0x3B65  /* Calpella */
+
+#define MEI_DEV_ID_CPT_1      0x1C3A  /* Couger Point */
+#define MEI_DEV_ID_PBG_1      0x1D3A  /* C600/X79 Patsburg */
+
+#define MEI_DEV_ID_PPT_1      0x1E3A  /* Panther Point */
+#define MEI_DEV_ID_PPT_2      0x1CBA  /* Panther Point */
+#define MEI_DEV_ID_PPT_3      0x1DBA  /* Panther Point */
 
 /*
  * MEI HW Section

drivers/misc/mei/init.c

@@ -24,6 +24,25 @@
 #include "interface.h"
 #include <linux/mei.h>
 
+const char *mei_dev_state_str(int state)
+{
+#define MEI_DEV_STATE(state) case MEI_DEV_##state: return #state
+	switch (state) {
+	MEI_DEV_STATE(INITIALIZING);
+	MEI_DEV_STATE(INIT_CLIENTS);
+	MEI_DEV_STATE(ENABLED);
+	MEI_DEV_STATE(RESETING);
+	MEI_DEV_STATE(DISABLED);
+	MEI_DEV_STATE(RECOVERING_FROM_RESET);
+	MEI_DEV_STATE(POWER_DOWN);
+	MEI_DEV_STATE(POWER_UP);
+	default:
+		return "unkown";
+	}
+#undef MEI_DEV_STATE
+}
+
+
 const uuid_le mei_amthi_guid  = UUID_LE(0x12f80028, 0xb4b7, 0x4b2d, 0xac,
 						0xa8, 0x46, 0xe0, 0xff, 0x65,
 						0x81, 0x4c);
@@ -123,7 +142,7 @@ struct mei_device *mei_device_init(struct pci_dev *pdev)
 	mutex_init(&dev->device_lock);
 	init_waitqueue_head(&dev->wait_recvd_msg);
 	init_waitqueue_head(&dev->wait_stop_wd);
-	dev->mei_state = MEI_INITIALIZING;
+	dev->dev_state = MEI_DEV_INITIALIZING;
 	dev->iamthif_state = MEI_IAMTHIF_IDLE;
 	dev->wd_interface_reg = false;
 
@@ -182,7 +201,7 @@ int mei_hw_init(struct mei_device *dev)
 	}
 
 	if (err <= 0 && !dev->recvd_msg) {
-		dev->mei_state = MEI_DISABLED;
+		dev->dev_state = MEI_DEV_DISABLED;
 		dev_dbg(&dev->pdev->dev,
 			"wait_event_interruptible_timeout failed"
 			"on wait for ME to turn on ME_RDY.\n");
@@ -192,7 +211,7 @@ int mei_hw_init(struct mei_device *dev)
 
 	if (!(((dev->host_hw_state & H_RDY) == H_RDY) &&
 	      ((dev->me_hw_state & ME_RDY_HRA) == ME_RDY_HRA))) {
-		dev->mei_state = MEI_DISABLED;
+		dev->dev_state = MEI_DEV_DISABLED;
 		dev_dbg(&dev->pdev->dev,
 			"host_hw_state = 0x%08x, me_hw_state = 0x%08x.\n",
 			dev->host_hw_state, dev->me_hw_state);
@@ -258,15 +277,15 @@ void mei_reset(struct mei_device *dev, int interrupts_enabled)
 	struct mei_cl_cb *cb_next = NULL;
 	bool unexpected;
 
-	if (dev->mei_state == MEI_RECOVERING_FROM_RESET) {
+	if (dev->dev_state == MEI_DEV_RECOVERING_FROM_RESET) {
 		dev->need_reset = true;
 		return;
 	}
 
-	unexpected = (dev->mei_state != MEI_INITIALIZING &&
-			dev->mei_state != MEI_DISABLED &&
-			dev->mei_state != MEI_POWER_DOWN &&
-			dev->mei_state != MEI_POWER_UP);
+	unexpected = (dev->dev_state != MEI_DEV_INITIALIZING &&
+			dev->dev_state != MEI_DEV_DISABLED &&
+			dev->dev_state != MEI_DEV_POWER_DOWN &&
+			dev->dev_state != MEI_DEV_POWER_UP);
 
 	dev->host_hw_state = mei_hcsr_read(dev);
 
@@ -285,10 +304,10 @@ void mei_reset(struct mei_device *dev, int interrupts_enabled)
 
 	dev->need_reset = false;
 
-	if (dev->mei_state != MEI_INITIALIZING) {
-		if (dev->mei_state != MEI_DISABLED &&
-		    dev->mei_state != MEI_POWER_DOWN)
-			dev->mei_state = MEI_RESETING;
+	if (dev->dev_state != MEI_DEV_INITIALIZING) {
+		if (dev->dev_state != MEI_DEV_DISABLED &&
+		    dev->dev_state != MEI_DEV_POWER_DOWN)
+			dev->dev_state = MEI_DEV_RESETING;
 
 		list_for_each_entry_safe(cl_pos,
 				cl_next, &dev->file_list, link) {
@@ -311,7 +330,6 @@ void mei_reset(struct mei_device *dev, int interrupts_enabled)
 
 	dev->me_clients_num = 0;
 	dev->rd_msg_hdr = 0;
-	dev->stop = false;
 	dev->wd_pending = false;
 
 	/* update the state of the registers after reset */
@@ -322,7 +340,8 @@ void mei_reset(struct mei_device *dev, int interrupts_enabled)
 	    dev->host_hw_state, dev->me_hw_state);
 
 	if (unexpected)
-		dev_warn(&dev->pdev->dev, "unexpected reset.\n");
+		dev_warn(&dev->pdev->dev, "unexpected reset: dev_state = %s\n",
+			 mei_dev_state_str(dev->dev_state));
 
 	/* Wake up all readings so they can be interrupted */
 	list_for_each_entry_safe(cl_pos, cl_next, &dev->file_list, link) {
@@ -371,7 +390,7 @@ void mei_host_start_message(struct mei_device *dev)
 	if (mei_write_message(dev, mei_hdr, (unsigned char *)host_start_req,
 				       mei_hdr->length)) {
 		dev_dbg(&dev->pdev->dev, "write send version message to FW fail.\n");
-		dev->mei_state = MEI_RESETING;
+		dev->dev_state = MEI_DEV_RESETING;
 		mei_reset(dev, 1);
 	}
 	dev->init_clients_state = MEI_START_MESSAGE;
@@ -403,7 +422,7 @@ void mei_host_enum_clients_message(struct mei_device *dev)
 	host_enum_req->hbm_cmd = HOST_ENUM_REQ_CMD;
 	if (mei_write_message(dev, mei_hdr, (unsigned char *)host_enum_req,
 				mei_hdr->length)) {
-		dev->mei_state = MEI_RESETING;
+		dev->dev_state = MEI_DEV_RESETING;
 		dev_dbg(&dev->pdev->dev, "write send enumeration request message to FW fail.\n");
 		mei_reset(dev, 1);
 	}
@@ -444,7 +463,7 @@ void mei_allocate_me_clients_storage(struct mei_device *dev)
 			sizeof(struct mei_me_client), GFP_KERNEL);
 	if (!clients) {
 		dev_dbg(&dev->pdev->dev, "memory allocation for ME clients failed.\n");
-		dev->mei_state = MEI_RESETING;
+		dev->dev_state = MEI_DEV_RESETING;
 		mei_reset(dev, 1);
 		return ;
 	}
@@ -490,7 +509,7 @@ int mei_host_client_properties(struct mei_device *dev)
 		if (mei_write_message(dev, mei_header,
 				(unsigned char *)host_cli_req,
 				mei_header->length)) {
-			dev->mei_state = MEI_RESETING;
+			dev->dev_state = MEI_DEV_RESETING;
 			dev_dbg(&dev->pdev->dev, "write send enumeration request message to FW fail.\n");
 			mei_reset(dev, 1);
 			return -EIO;
@@ -522,12 +541,12 @@ void mei_cl_init(struct mei_cl *priv, struct mei_device *dev)
 	priv->dev = dev;
 }
 
-int mei_find_me_client_index(const struct mei_device *dev, uuid_le cuuid)
+int mei_me_cl_by_uuid(const struct mei_device *dev, const uuid_le *cuuid)
 {
-	int i, res = -1;
+	int i, res = -ENOENT;
 
 	for (i = 0; i < dev->me_clients_num; ++i)
-		if (uuid_le_cmp(cuuid,
+		if (uuid_le_cmp(*cuuid,
 				dev->me_clients[i].props.protocol_name) == 0) {
 			res = i;
 			break;
@@ -538,35 +557,35 @@ int mei_find_me_client_index(const struct mei_device *dev, uuid_le cuuid)
 
 
 /**
- * mei_find_me_client_update_filext - searches for ME client guid
+ * mei_me_cl_update_filext - searches for ME client guid
  *                       sets client_id in mei_file_private if found
  * @dev: the device structure
- * @priv: private file structure to set client_id in
- * @cguid: searched guid of ME client
+ * @cl: private file structure to set client_id in
+ * @cuuid: searched uuid of ME client
  * @client_id: id of host client to be set in file private structure
  *
  * returns ME client index
  */
-u8 mei_find_me_client_update_filext(struct mei_device *dev, struct mei_cl *priv,
-				const uuid_le *cguid, u8 client_id)
+int mei_me_cl_update_filext(struct mei_device *dev, struct mei_cl *cl,
+				const uuid_le *cuuid, u8 host_cl_id)
 {
 	int i;
 
-	if (!dev || !priv || !cguid)
-		return 0;
+	if (!dev || !cl || !cuuid)
+		return -EINVAL;
 
 	/* check for valid client id */
-	i = mei_find_me_client_index(dev, *cguid);
+	i = mei_me_cl_by_uuid(dev, cuuid);
 	if (i >= 0) {
-		priv->me_client_id = dev->me_clients[i].client_id;
-		priv->state = MEI_FILE_CONNECTING;
-		priv->host_client_id = client_id;
+		cl->me_client_id = dev->me_clients[i].client_id;
+		cl->state = MEI_FILE_CONNECTING;
+		cl->host_client_id = host_cl_id;
 
-		list_add_tail(&priv->link, &dev->file_list);
+		list_add_tail(&cl->link, &dev->file_list);
 		return (u8)i;
 	}
 
-	return 0;
+	return -ENOENT;
 }
 
 /**
@@ -577,16 +596,16 @@ u8 mei_find_me_client_update_filext(struct mei_device *dev, struct mei_cl *priv,
  */
 void mei_host_init_iamthif(struct mei_device *dev)
 {
-	u8 i;
+	int i;
 	unsigned char *msg_buf;
 
 	mei_cl_init(&dev->iamthif_cl, dev);
 	dev->iamthif_cl.state = MEI_FILE_DISCONNECTED;
 
 	/* find ME amthi client */
-	i = mei_find_me_client_update_filext(dev, &dev->iamthif_cl,
+	i = mei_me_cl_update_filext(dev, &dev->iamthif_cl,
 			    &mei_amthi_guid, MEI_IAMTHIF_HOST_CLIENT_ID);
-	if (dev->iamthif_cl.state != MEI_FILE_CONNECTING) {
+	if (i < 0) {
 		dev_dbg(&dev->pdev->dev, "failed to find iamthif client.\n");
 		return;
 	}

drivers/misc/mei/interface.h

@@ -23,14 +23,6 @@
 #include "mei_dev.h"
 
 
-#define AMT_WD_DEFAULT_TIMEOUT 120	/* seconds */
-#define AMT_WD_MIN_TIMEOUT 120	/* seconds */
-#define AMT_WD_MAX_TIMEOUT 65535	/* seconds */
-
-#define MEI_WATCHDOG_DATA_SIZE         16
-#define MEI_START_WD_DATA_SIZE         20
-#define MEI_WD_PARAMS_SIZE             4
-
 
 void mei_read_slots(struct mei_device *dev,
 		     unsigned char *buffer,
@@ -64,7 +56,7 @@ int mei_flow_ctrl_creds(struct mei_device *dev, struct mei_cl *cl);
 
 
 int mei_wd_send(struct mei_device *dev);
-int mei_wd_stop(struct mei_device *dev, bool preserve);
+int mei_wd_stop(struct mei_device *dev);
 int mei_wd_host_init(struct mei_device *dev);
 /*
  * mei_watchdog_register  - Registering watchdog interface

drivers/misc/mei/interrupt.c

@@ -633,7 +633,7 @@ static void mei_irq_thread_read_bus_message(struct mei_device *dev,
 		if (version_res->host_version_supported) {
 			dev->version.major_version = HBM_MAJOR_VERSION;
 			dev->version.minor_version = HBM_MINOR_VERSION;
-			if (dev->mei_state == MEI_INIT_CLIENTS &&
+			if (dev->dev_state == MEI_DEV_INIT_CLIENTS &&
 			    dev->init_clients_state == MEI_START_MESSAGE) {
 				dev->init_clients_timer = 0;
 				mei_host_enum_clients_message(dev);
@@ -707,7 +707,7 @@ static void mei_irq_thread_read_bus_message(struct mei_device *dev,
 			dev->me_clients[dev->me_client_presentation_num].props
 						= props_res->client_properties;
 
-			if (dev->mei_state == MEI_INIT_CLIENTS &&
+			if (dev->dev_state == MEI_DEV_INIT_CLIENTS &&
 			    dev->init_clients_state ==
 					MEI_CLIENT_PROPERTIES_MESSAGE) {
 				dev->me_client_index++;
@@ -734,7 +734,7 @@ static void mei_irq_thread_read_bus_message(struct mei_device *dev,
 					 * Client ID 2 - Reserved for AMTHI
 					 */
 					bitmap_set(dev->host_clients_map, 0, 3);
-					dev->mei_state = MEI_ENABLED;
+					dev->dev_state = MEI_DEV_ENABLED;
 
 					/* if wd initialization fails, initialization the AMTHI client,
 					 * otherwise the AMTHI client will be initialized after the WD client connect response
@@ -759,7 +759,7 @@ static void mei_irq_thread_read_bus_message(struct mei_device *dev,
 	case HOST_ENUM_RES_CMD:
 		enum_res = (struct hbm_host_enum_response *) mei_msg;
 		memcpy(dev->me_clients_map, enum_res->valid_addresses, 32);
-		if (dev->mei_state == MEI_INIT_CLIENTS &&
+		if (dev->dev_state == MEI_DEV_INIT_CLIENTS &&
 		    dev->init_clients_state == MEI_ENUM_CLIENTS_MESSAGE) {
 				dev->init_clients_timer = 0;
 				dev->me_client_presentation_num = 0;
@@ -776,7 +776,7 @@ static void mei_irq_thread_read_bus_message(struct mei_device *dev,
 		break;
 
 	case HOST_STOP_RES_CMD:
-		dev->mei_state = MEI_DISABLED;
+		dev->dev_state = MEI_DEV_DISABLED;
 		dev_dbg(&dev->pdev->dev, "resetting because of FW stop response.\n");
 		mei_reset(dev, 1);
 		break;
@@ -1224,10 +1224,9 @@ static int mei_irq_thread_write_handler(struct mei_io_list *cmpl_list,
 		}
 	}
 
-	if (dev->stop && !dev->wd_pending) {
-		dev->wd_stopped = true;
+	if (dev->wd_state == MEI_WD_STOPPING) {
+		dev->wd_state = MEI_WD_IDLE;
 		wake_up_interruptible(&dev->wait_stop_wd);
-		return 0;
 	}
 
 	if (dev->extra_write_index) {
@@ -1240,7 +1239,7 @@ static int mei_irq_thread_write_handler(struct mei_io_list *cmpl_list,
 		*slots -= dev->extra_write_index;
 		dev->extra_write_index = 0;
 	}
-	if (dev->mei_state == MEI_ENABLED) {
+	if (dev->dev_state == MEI_DEV_ENABLED) {
 		if (dev->wd_pending &&
 		    mei_flow_ctrl_creds(dev, &dev->wd_cl) > 0) {
 			if (mei_wd_send(dev))
@@ -1250,14 +1249,12 @@ static int mei_irq_thread_write_handler(struct mei_io_list *cmpl_list,
 
 			dev->wd_pending = false;
 
-			if (dev->wd_timeout)
-				*slots -= mei_data2slots(MEI_START_WD_DATA_SIZE);
+			if (dev->wd_state == MEI_WD_RUNNING)
+				*slots -= mei_data2slots(MEI_WD_START_MSG_SIZE);
 			else
-				*slots -= mei_data2slots(MEI_WD_PARAMS_SIZE);
+				*slots -= mei_data2slots(MEI_WD_STOP_MSG_SIZE);
 		}
 	}
-	if (dev->stop)
-		return -ENODEV;
 
 	/* complete control write list CB */
 	dev_dbg(&dev->pdev->dev, "complete control write list cb.\n");
@@ -1361,8 +1358,8 @@ void mei_timer(struct work_struct *work)
 
 
 	mutex_lock(&dev->device_lock);
-	if (dev->mei_state != MEI_ENABLED) {
-		if (dev->mei_state == MEI_INIT_CLIENTS) {
+	if (dev->dev_state != MEI_DEV_ENABLED) {
+		if (dev->dev_state == MEI_DEV_INIT_CLIENTS) {
 			if (dev->init_clients_timer) {
 				if (--dev->init_clients_timer == 0) {
 					dev_dbg(&dev->pdev->dev, "IMEI reset due to init clients timeout ,init clients state = %d.\n",
@@ -1484,8 +1481,8 @@ irqreturn_t mei_interrupt_thread_handler(int irq, void *dev_id)
 
 	/* check if ME wants a reset */
 	if ((dev->me_hw_state & ME_RDY_HRA) == 0 &&
-	    dev->mei_state != MEI_RESETING &&
-	    dev->mei_state != MEI_INITIALIZING) {
+	    dev->dev_state != MEI_DEV_RESETING &&
+	    dev->dev_state != MEI_DEV_INITIALIZING) {
 		dev_dbg(&dev->pdev->dev, "FW not ready.\n");
 		mei_reset(dev, 1);
 		mutex_unlock(&dev->device_lock);
@@ -1498,7 +1495,7 @@ irqreturn_t mei_interrupt_thread_handler(int irq, void *dev_id)
 			dev_dbg(&dev->pdev->dev, "we need to start the dev.\n");
 			dev->host_hw_state |= (H_IE | H_IG | H_RDY);
 			mei_hcsr_set(dev);
-			dev->mei_state = MEI_INIT_CLIENTS;
+			dev->dev_state = MEI_DEV_INIT_CLIENTS;
 			dev_dbg(&dev->pdev->dev, "link is established start sending messages.\n");
 			/* link is established
 			 * start sending messages.

drivers/misc/mei/iorw.c

@@ -38,7 +38,31 @@
 #include <linux/mei.h>
 #include "interface.h"
 
+/**
+ * mei_me_cl_by_id return index to me_clients for client_id
+ *
+ * @dev: the device structure
+ * @client_id: me client id
+ *
+ * Locking: called under "dev->device_lock" lock
+ *
+ * returns index on success, -ENOENT on failure.
+ */
 
+int mei_me_cl_by_id(struct mei_device *dev, u8 client_id)
+{
+	int i;
+	for (i = 0; i < dev->me_clients_num; i++)
+		if (dev->me_clients[i].client_id == client_id)
+			break;
+	if (WARN_ON(dev->me_clients[i].client_id != client_id))
+		return -ENOENT;
+
+	if (i == dev->me_clients_num)
+		return -ENOENT;
+
+	return i;
+}
 
 /**
  * mei_ioctl_connect_client - the connect to fw client IOCTL function
@@ -84,7 +108,7 @@ int mei_ioctl_connect_client(struct file *file,
 
 	cb->major_file_operations = MEI_IOCTL;
 
-	if (dev->mei_state != MEI_ENABLED) {
+	if (dev->dev_state != MEI_DEV_ENABLED) {
 		rets = -ENODEV;
 		goto end;
 	}
@@ -95,7 +119,7 @@ int mei_ioctl_connect_client(struct file *file,
 	}
 
 	/* find ME client we're trying to connect to */
-	i = mei_find_me_client_index(dev, data->in_client_uuid);
+	i = mei_me_cl_by_uuid(dev, &data->in_client_uuid);
 	if (i >= 0 && !dev->me_clients[i].props.fixed_address) {
 		cl->me_client_id = dev->me_clients[i].client_id;
 		cl->state = MEI_FILE_CONNECTING;
@@ -273,19 +297,12 @@ int amthi_read(struct mei_device *dev, struct file *file,
 		return -ETIMEDOUT;
 	}
 
-	for (i = 0; i < dev->me_clients_num; i++) {
-		if (dev->me_clients[i].client_id ==
-		    dev->iamthif_cl.me_client_id)
-			break;
-	}
+	i = mei_me_cl_by_id(dev, dev->iamthif_cl.me_client_id);
 
-	if (i == dev->me_clients_num) {
+	if (i < 0) {
 		dev_dbg(&dev->pdev->dev, "amthi client not found.\n");
 		return -ENODEV;
 	}
-	if (WARN_ON(dev->me_clients[i].client_id != cl->me_client_id))
-		return -ENODEV;
-
 	dev_dbg(&dev->pdev->dev, "checking amthi data\n");
 	cb = find_amthi_read_list_entry(dev, file);
 
@@ -316,8 +333,7 @@ int amthi_read(struct mei_device *dev, struct file *file,
 	dev->iamthif_timer = 0;
 
 	if (cb) {
-		timeout = cb->read_time +
-					msecs_to_jiffies(IAMTHIF_READ_TIMER);
+		timeout = cb->read_time + msecs_to_jiffies(IAMTHIF_READ_TIMER);
 		dev_dbg(&dev->pdev->dev, "amthi timeout = %lud\n",
 				timeout);
 
@@ -386,7 +402,7 @@ int mei_start_read(struct mei_device *dev, struct mei_cl *cl)
 	if (cl->state != MEI_FILE_CONNECTED)
 		return -ENODEV;
 
-	if (dev->mei_state != MEI_ENABLED)
+	if (dev->dev_state != MEI_DEV_ENABLED)
 		return -ENODEV;
 
 	dev_dbg(&dev->pdev->dev, "check if read is pending.\n");
@@ -401,19 +417,8 @@ int mei_start_read(struct mei_device *dev, struct mei_cl *cl)
 
 	dev_dbg(&dev->pdev->dev, "allocation call back successful. host client = %d, ME client = %d\n",
 		cl->host_client_id, cl->me_client_id);
-
-	for (i = 0; i < dev->me_clients_num; i++) {
-		if (dev->me_clients[i].client_id == cl->me_client_id)
-			break;
-
-	}
-
-	if (WARN_ON(dev->me_clients[i].client_id != cl->me_client_id)) {
-		rets = -ENODEV;
-		goto unlock;
-	}
-
-	if (i == dev->me_clients_num) {
+	i = mei_me_cl_by_id(dev, cl->me_client_id);
+	if (i < 0) {
 		rets = -ENODEV;
 		goto unlock;
 	}

drivers/misc/mei/main.c

@@ -41,8 +41,6 @@
 #include <linux/mei.h>
 #include "interface.h"
 
-static const char mei_driver_name[] = "mei";
-
 /* The device pointer */
 /* Currently this driver works as long as there is only a single AMT device. */
 struct pci_dev *mei_device;
@@ -234,9 +232,9 @@ static int mei_open(struct inode *inode, struct file *file)
 		goto out_unlock;
 
 	err = -ENODEV;
-	if (dev->mei_state != MEI_ENABLED) {
-		dev_dbg(&dev->pdev->dev, "mei_state != MEI_ENABLED  mei_state= %d\n",
-		    dev->mei_state);
+	if (dev->dev_state != MEI_DEV_ENABLED) {
+		dev_dbg(&dev->pdev->dev, "dev_state != MEI_ENABLED  dev_state = %s\n",
+		    mei_dev_state_str(dev->dev_state));
 		goto out_unlock;
 	}
 	err = -EMFILE;
@@ -386,17 +384,16 @@ static ssize_t mei_read(struct file *file, char __user *ubuf,
 	dev = cl->dev;
 
 	mutex_lock(&dev->device_lock);
-	if (dev->mei_state != MEI_ENABLED) {
+	if (dev->dev_state != MEI_DEV_ENABLED) {
 		rets = -ENODEV;
 		goto out;
 	}
 
 	if ((cl->sm_state & MEI_WD_STATE_INDEPENDENCE_MSG_SENT) == 0) {
 		/* Do not allow to read watchdog client */
-		i = mei_find_me_client_index(dev, mei_wd_guid);
+		i = mei_me_cl_by_uuid(dev, &mei_wd_guid);
 		if (i >= 0) {
 			struct mei_me_client *me_client = &dev->me_clients[i];
-
 			if (cl->me_client_id == me_client->client_id) {
 				rets = -EBADF;
 				goto out;
@@ -541,7 +538,7 @@ static ssize_t mei_write(struct file *file, const char __user *ubuf,
 
 	mutex_lock(&dev->device_lock);
 
-	if (dev->mei_state != MEI_ENABLED) {
+	if (dev->dev_state != MEI_DEV_ENABLED) {
 		mutex_unlock(&dev->device_lock);
 		return -ENODEV;
 	}
@@ -616,26 +613,16 @@ static ssize_t mei_write(struct file *file, const char __user *ubuf,
 			rets = -ENOMEM;
 			goto unlock_dev;
 		}
-		if (dev->mei_state != MEI_ENABLED) {
+		if (dev->dev_state != MEI_DEV_ENABLED) {
 			rets = -ENODEV;
 			goto unlock_dev;
 		}
-		for (i = 0; i < dev->me_clients_num; i++) {
-			if (dev->me_clients[i].client_id ==
-				dev->iamthif_cl.me_client_id)
-				break;
-		}
-
-		if (WARN_ON(dev->me_clients[i].client_id != cl->me_client_id)) {
+		i = mei_me_cl_by_id(dev, dev->iamthif_cl.me_client_id);
+		if (i < 0) {
 			rets = -ENODEV;
 			goto unlock_dev;
 		}
-		if (i == dev->me_clients_num ||
-		    (dev->me_clients[i].client_id !=
-		      dev->iamthif_cl.me_client_id)) {
-			rets = -ENODEV;
-			goto unlock_dev;
-		} else if (length > dev->me_clients[i].props.max_msg_length ||
+		if (length > dev->me_clients[i].props.max_msg_length ||
 			   length <= 0) {
 			rets = -EMSGSIZE;
 			goto unlock_dev;
@@ -688,16 +675,8 @@ static ssize_t mei_write(struct file *file, const char __user *ubuf,
 		    cl->me_client_id);
 		goto unlock_dev;
 	}
-	for (i = 0; i < dev->me_clients_num; i++) {
-		if (dev->me_clients[i].client_id ==
-		    cl->me_client_id)
-			break;
-	}
-	if (WARN_ON(dev->me_clients[i].client_id != cl->me_client_id)) {
-		rets = -ENODEV;
-		goto unlock_dev;
-	}
-	if (i == dev->me_clients_num) {
+	i = mei_me_cl_by_id(dev, cl->me_client_id);
+	if (i < 0) {
 		rets = -ENODEV;
 		goto unlock_dev;
 	}
@@ -790,7 +769,7 @@ static long mei_ioctl(struct file *file, unsigned int cmd, unsigned long data)
 	dev_dbg(&dev->pdev->dev, "IOCTL cmd = 0x%x", cmd);
 
 	mutex_lock(&dev->device_lock);
-	if (dev->mei_state != MEI_ENABLED) {
+	if (dev->dev_state != MEI_DEV_ENABLED) {
 		rets = -ENODEV;
 		goto out;
 	}
@@ -869,7 +848,7 @@ static unsigned int mei_poll(struct file *file, poll_table *wait)
 
 	mutex_lock(&dev->device_lock);
 
-	if (dev->mei_state != MEI_ENABLED)
+	if (dev->dev_state != MEI_DEV_ENABLED)
 		goto out;
 
 
@@ -979,7 +958,7 @@ static int __devinit mei_probe(struct pci_dev *pdev,
 	/* set PCI host mastering  */
 	pci_set_master(pdev);
 	/* pci request regions for mei driver */
-	err = pci_request_regions(pdev, mei_driver_name);
+	err = pci_request_regions(pdev, KBUILD_MODNAME);
 	if (err) {
 		dev_err(&pdev->dev, "failed to get pci regions.\n");
 		goto disable_device;
@@ -1004,12 +983,12 @@ static int __devinit mei_probe(struct pci_dev *pdev,
 		err = request_threaded_irq(pdev->irq,
 			NULL,
 			mei_interrupt_thread_handler,
-			IRQF_ONESHOT, mei_driver_name, dev);
+			IRQF_ONESHOT, KBUILD_MODNAME, dev);
 	else
 		err = request_threaded_irq(pdev->irq,
 			mei_interrupt_quick_handler,
 			mei_interrupt_thread_handler,
-			IRQF_SHARED, mei_driver_name, dev);
+			IRQF_SHARED, KBUILD_MODNAME, dev);
 
 	if (err) {
 		dev_err(&pdev->dev, "request_threaded_irq failure. irq = %d\n",
@@ -1081,7 +1060,9 @@ static void __devexit mei_remove(struct pci_dev *pdev)
 
 	mutex_lock(&dev->device_lock);
 
-	mei_wd_stop(dev, false);
+	cancel_delayed_work(&dev->timer_work);
+
+	mei_wd_stop(dev);
 
 	mei_device = NULL;
 
@@ -1136,12 +1117,15 @@ static int mei_pci_suspend(struct device *device)
 	if (!dev)
 		return -ENODEV;
 	mutex_lock(&dev->device_lock);
+
+	cancel_delayed_work(&dev->timer_work);
+
 	/* Stop watchdog if exists */
-	err = mei_wd_stop(dev, true);
+	err = mei_wd_stop(dev);
 	/* Set new mei state */
-	if (dev->mei_state == MEI_ENABLED ||
-	    dev->mei_state == MEI_RECOVERING_FROM_RESET) {
-		dev->mei_state = MEI_POWER_DOWN;
+	if (dev->dev_state == MEI_DEV_ENABLED ||
+	    dev->dev_state == MEI_DEV_RECOVERING_FROM_RESET) {
+		dev->dev_state = MEI_DEV_POWER_DOWN;
 		mei_reset(dev, 0);
 	}
 	mutex_unlock(&dev->device_lock);
@@ -1169,12 +1153,12 @@ static int mei_pci_resume(struct device *device)
 		err = request_threaded_irq(pdev->irq,
 			NULL,
 			mei_interrupt_thread_handler,
-			IRQF_ONESHOT, mei_driver_name, dev);
+			IRQF_ONESHOT, KBUILD_MODNAME, dev);
 	else
 		err = request_threaded_irq(pdev->irq,
 			mei_interrupt_quick_handler,
 			mei_interrupt_thread_handler,
-			IRQF_SHARED, mei_driver_name, dev);
+			IRQF_SHARED, KBUILD_MODNAME, dev);
 
 	if (err) {
 		dev_err(&pdev->dev, "request_threaded_irq failed: irq = %d.\n",
@@ -1183,7 +1167,7 @@ static int mei_pci_resume(struct device *device)
 	}
 
 	mutex_lock(&dev->device_lock);
-	dev->mei_state = MEI_POWER_UP;
+	dev->dev_state = MEI_DEV_POWER_UP;
 	mei_reset(dev, 1);
 	mutex_unlock(&dev->device_lock);
 
@@ -1201,7 +1185,7 @@ static SIMPLE_DEV_PM_OPS(mei_pm_ops, mei_pci_suspend, mei_pci_resume);
  *  PCI driver structure
  */
 static struct pci_driver mei_driver = {
-	.name = mei_driver_name,
+	.name = KBUILD_MODNAME,
 	.id_table = mei_pci_tbl,
 	.probe = mei_probe,
 	.remove = __devexit_p(mei_remove),

drivers/misc/mei/mei_dev.h

@@ -25,9 +25,16 @@
 /*
  * watch dog definition
  */
-#define MEI_WATCHDOG_DATA_SIZE         16
-#define MEI_START_WD_DATA_SIZE         20
-#define MEI_WD_PARAMS_SIZE             4
+#define MEI_WD_HDR_SIZE       4
+#define MEI_WD_STOP_MSG_SIZE  MEI_WD_HDR_SIZE
+#define MEI_WD_START_MSG_SIZE (MEI_WD_HDR_SIZE + 16)
+
+#define MEI_WD_DEFAULT_TIMEOUT   120  /* seconds */
+#define MEI_WD_MIN_TIMEOUT       120  /* seconds */
+#define MEI_WD_MAX_TIMEOUT     65535  /* seconds */
+
+#define MEI_WD_STOP_TIMEOUT      10 /* msecs */
+
 #define MEI_WD_STATE_INDEPENDENCE_MSG_SENT       (1 << 0)
 
 #define MEI_RD_MSG_BUF_SIZE           (128 * sizeof(u32))
@@ -78,17 +85,19 @@ enum file_state {
 };
 
 /* MEI device states */
-enum mei_states {
-	MEI_INITIALIZING = 0,
-	MEI_INIT_CLIENTS,
-	MEI_ENABLED,
-	MEI_RESETING,
-	MEI_DISABLED,
-	MEI_RECOVERING_FROM_RESET,
-	MEI_POWER_DOWN,
-	MEI_POWER_UP
+enum mei_dev_state {
+	MEI_DEV_INITIALIZING = 0,
+	MEI_DEV_INIT_CLIENTS,
+	MEI_DEV_ENABLED,
+	MEI_DEV_RESETING,
+	MEI_DEV_DISABLED,
+	MEI_DEV_RECOVERING_FROM_RESET,
+	MEI_DEV_POWER_DOWN,
+	MEI_DEV_POWER_UP
 };
 
+const char *mei_dev_state_str(int state);
+
 /* init clients states*/
 enum mei_init_clients_states {
 	MEI_START_MESSAGE = 0,
@@ -113,6 +122,12 @@ enum mei_file_transaction_states {
 	MEI_READ_COMPLETE
 };
 
+enum mei_wd_states {
+	MEI_WD_IDLE,
+	MEI_WD_RUNNING,
+	MEI_WD_STOPPING,
+};
+
 /* MEI CB */
 enum mei_cb_major_types {
 	MEI_READ = 0,
@@ -218,10 +233,9 @@ struct mei_device {
 	/*
 	 * mei device  states
 	 */
-	enum mei_states mei_state;
+	enum mei_dev_state dev_state;
 	enum mei_init_clients_states init_clients_state;
 	u16 init_clients_timer;
-	bool stop;
 	bool need_reset;
 
 	u32 extra_write_index;
@@ -241,12 +255,11 @@ struct mei_device {
 	bool mei_host_buffer_is_empty;
 
 	struct mei_cl wd_cl;
+	enum mei_wd_states wd_state;
 	bool wd_interface_reg;
 	bool wd_pending;
-	bool wd_stopped;
-	bool wd_bypass;	/* if false, don't refresh watchdog ME client */
-	u16 wd_timeout;	/* seconds ((wd_data[1] << 8) + wd_data[0]) */
-	unsigned char wd_data[MEI_START_WD_DATA_SIZE];
+	u16 wd_timeout;
+	unsigned char wd_data[MEI_WD_START_MSG_SIZE];
 
 
 	struct file *iamthif_file_object;
@@ -279,9 +292,10 @@ void mei_host_init_iamthif(struct mei_device *dev);
 void mei_allocate_me_clients_storage(struct mei_device *dev);
 
 
-u8 mei_find_me_client_update_filext(struct mei_device *dev,
-				struct mei_cl *priv,
-				const uuid_le *cguid, u8 client_id);
+int mei_me_cl_update_filext(struct mei_device *dev, struct mei_cl *cl,
+			const uuid_le *cguid, u8 host_client_id);
+int mei_me_cl_by_uuid(const struct mei_device *dev, const uuid_le *cuuid);
+int mei_me_cl_by_id(struct mei_device *dev, u8 client_id);
 
 /*
  * MEI IO List Functions
@@ -348,7 +362,6 @@ void mei_run_next_iamthif_cmd(struct mei_device *dev);
 
 void mei_free_cb_private(struct mei_cl_cb *priv_cb);
 
-int mei_find_me_client_index(const struct mei_device *dev, uuid_le cuuid);
 
 /*
  * Register Access Function

drivers/misc/mei/wd.c

@@ -48,8 +48,8 @@ const uuid_le mei_wd_guid = UUID_LE(0x05B79A6F, 0x4628, 0x4D7F, 0x89,
 static void mei_wd_set_start_timeout(struct mei_device *dev, u16 timeout)
 {
 	dev_dbg(&dev->pdev->dev, "wd: set timeout=%d.\n", timeout);
-	memcpy(dev->wd_data, mei_start_wd_params, MEI_WD_PARAMS_SIZE);
-	memcpy(dev->wd_data + MEI_WD_PARAMS_SIZE, &timeout, sizeof(u16));
+	memcpy(dev->wd_data, mei_start_wd_params, MEI_WD_HDR_SIZE);
+	memcpy(dev->wd_data + MEI_WD_HDR_SIZE, &timeout, sizeof(u16));
 }
 
 /**
@@ -66,10 +66,11 @@ int mei_wd_host_init(struct mei_device *dev)
 
 	/* look for WD client and connect to it */
 	dev->wd_cl.state = MEI_FILE_DISCONNECTED;
-	dev->wd_timeout = AMT_WD_DEFAULT_TIMEOUT;
+	dev->wd_timeout = MEI_WD_DEFAULT_TIMEOUT;
+	dev->wd_state = MEI_WD_IDLE;
 
 	/* find ME WD client */
-	mei_find_me_client_update_filext(dev, &dev->wd_cl,
+	mei_me_cl_update_filext(dev, &dev->wd_cl,
 				&mei_wd_guid, MEI_WD_HOST_CLIENT_ID);
 
 	dev_dbg(&dev->pdev->dev, "wd: check client\n");
@@ -108,10 +109,10 @@ int mei_wd_send(struct mei_device *dev)
 	mei_hdr->msg_complete = 1;
 	mei_hdr->reserved = 0;
 
-	if (!memcmp(dev->wd_data, mei_start_wd_params, MEI_WD_PARAMS_SIZE))
-		mei_hdr->length = MEI_START_WD_DATA_SIZE;
-	else if (!memcmp(dev->wd_data, mei_stop_wd_params, MEI_WD_PARAMS_SIZE))
-		mei_hdr->length = MEI_WD_PARAMS_SIZE;
+	if (!memcmp(dev->wd_data, mei_start_wd_params, MEI_WD_HDR_SIZE))
+		mei_hdr->length = MEI_WD_START_MSG_SIZE;
+	else if (!memcmp(dev->wd_data, mei_stop_wd_params, MEI_WD_HDR_SIZE))
+		mei_hdr->length = MEI_WD_STOP_MSG_SIZE;
 	else
 		return -EINVAL;
 
@@ -128,18 +129,17 @@ int mei_wd_send(struct mei_device *dev)
  *	-EIO when message send fails
  *	-EINVAL when invalid message is to be sent
  */
-int mei_wd_stop(struct mei_device *dev, bool preserve)
+int mei_wd_stop(struct mei_device *dev)
 {
 	int ret;
-	u16 wd_timeout = dev->wd_timeout;
 
-	cancel_delayed_work(&dev->timer_work);
-	if (dev->wd_cl.state != MEI_FILE_CONNECTED || !dev->wd_timeout)
+	if (dev->wd_cl.state != MEI_FILE_CONNECTED ||
+	    dev->wd_state != MEI_WD_RUNNING)
 		return 0;
 
-	dev->wd_timeout = 0;
-	memcpy(dev->wd_data, mei_stop_wd_params, MEI_WD_PARAMS_SIZE);
-	dev->stop = true;
+	memcpy(dev->wd_data, mei_stop_wd_params, MEI_WD_STOP_MSG_SIZE);
+
+	dev->wd_state = MEI_WD_STOPPING;
 
 	ret = mei_flow_ctrl_creds(dev, &dev->wd_cl);
 	if (ret < 0)
@@ -161,13 +161,14 @@ int mei_wd_stop(struct mei_device *dev, bool preserve)
 	} else {
 		dev->wd_pending = true;
 	}
-	dev->wd_stopped = false;
+
 	mutex_unlock(&dev->device_lock);
 
 	ret = wait_event_interruptible_timeout(dev->wait_stop_wd,
-					dev->wd_stopped, 10 * HZ);
+					dev->wd_state == MEI_WD_IDLE,
+					msecs_to_jiffies(MEI_WD_STOP_TIMEOUT));
 	mutex_lock(&dev->device_lock);
-	if (dev->wd_stopped) {
+	if (dev->wd_state == MEI_WD_IDLE) {
 		dev_dbg(&dev->pdev->dev, "wd: stop completed ret=%d.\n", ret);
 		ret = 0;
 	} else {
@@ -177,9 +178,6 @@ int mei_wd_stop(struct mei_device *dev, bool preserve)
 			"wd: stop failed to complete ret=%d.\n", ret);
 	}
 
-	if (preserve)
-		dev->wd_timeout = wd_timeout;
-
 out:
 	return ret;
 }
@@ -196,16 +194,16 @@ static int mei_wd_ops_start(struct watchdog_device *wd_dev)
 	int err = -ENODEV;
 	struct mei_device *dev;
 
-	dev = pci_get_drvdata(mei_device);
+	dev = watchdog_get_drvdata(wd_dev);
 	if (!dev)
 		return -ENODEV;
 
 	mutex_lock(&dev->device_lock);
 
-	if (dev->mei_state != MEI_ENABLED) {
+	if (dev->dev_state != MEI_DEV_ENABLED) {
 		dev_dbg(&dev->pdev->dev,
-			"wd: mei_state != MEI_ENABLED  mei_state = %d\n",
-			dev->mei_state);
+			"wd: dev_state != MEI_DEV_ENABLED  dev_state = %s\n",
+			mei_dev_state_str(dev->dev_state));
 		goto end_unlock;
 	}
 
@@ -233,13 +231,13 @@ static int mei_wd_ops_start(struct watchdog_device *wd_dev)
 static int mei_wd_ops_stop(struct watchdog_device *wd_dev)
 {
 	struct mei_device *dev;
-	dev = pci_get_drvdata(mei_device);
 
+	dev = watchdog_get_drvdata(wd_dev);
 	if (!dev)
 		return -ENODEV;
 
 	mutex_lock(&dev->device_lock);
-	mei_wd_stop(dev, false);
+	mei_wd_stop(dev);
 	mutex_unlock(&dev->device_lock);
 
 	return 0;
@@ -256,8 +254,8 @@ static int mei_wd_ops_ping(struct watchdog_device *wd_dev)
 {
 	int ret = 0;
 	struct mei_device *dev;
-	dev = pci_get_drvdata(mei_device);
 
+	dev = watchdog_get_drvdata(wd_dev);
 	if (!dev)
 		return -ENODEV;
 
@@ -269,6 +267,8 @@ static int mei_wd_ops_ping(struct watchdog_device *wd_dev)
 		goto end;
 	}
 
+	dev->wd_state = MEI_WD_RUNNING;
+
 	/* Check if we can send the ping to HW*/
 	if (dev->mei_host_buffer_is_empty &&
 		mei_flow_ctrl_creds(dev, &dev->wd_cl) > 0) {
@@ -309,13 +309,13 @@ static int mei_wd_ops_ping(struct watchdog_device *wd_dev)
 static int mei_wd_ops_set_timeout(struct watchdog_device *wd_dev, unsigned int timeout)
 {
 	struct mei_device *dev;
-	dev = pci_get_drvdata(mei_device);
 
+	dev = watchdog_get_drvdata(wd_dev);
 	if (!dev)
 		return -ENODEV;
 
 	/* Check Timeout value */
-	if (timeout < AMT_WD_MIN_TIMEOUT || timeout > AMT_WD_MAX_TIMEOUT)
+	if (timeout < MEI_WD_MIN_TIMEOUT || timeout > MEI_WD_MAX_TIMEOUT)
 		return -EINVAL;
 
 	mutex_lock(&dev->device_lock);
@@ -341,37 +341,42 @@ static const struct watchdog_ops wd_ops = {
 };
 static const struct watchdog_info wd_info = {
 		.identity = INTEL_AMT_WATCHDOG_ID,
-		.options = WDIOF_KEEPALIVEPING | WDIOF_ALARMONLY,
+		.options = WDIOF_KEEPALIVEPING |
+			   WDIOF_SETTIMEOUT |
+			   WDIOF_ALARMONLY,
 };
 
 static struct watchdog_device amt_wd_dev = {
 		.info = &wd_info,
 		.ops = &wd_ops,
-		.timeout = AMT_WD_DEFAULT_TIMEOUT,
-		.min_timeout = AMT_WD_MIN_TIMEOUT,
-		.max_timeout = AMT_WD_MAX_TIMEOUT,
+		.timeout = MEI_WD_DEFAULT_TIMEOUT,
+		.min_timeout = MEI_WD_MIN_TIMEOUT,
+		.max_timeout = MEI_WD_MAX_TIMEOUT,
 };
 
 
-void  mei_watchdog_register(struct mei_device *dev)
+void mei_watchdog_register(struct mei_device *dev)
 {
-	dev_dbg(&dev->pdev->dev, "dev->wd_timeout =%d.\n", dev->wd_timeout);
-
 	if (watchdog_register_device(&amt_wd_dev)) {
 		dev_err(&dev->pdev->dev,
 			"wd: unable to register watchdog device.\n");
 		dev->wd_interface_reg = false;
-	} else {
-		dev_dbg(&dev->pdev->dev,
-			"wd: successfully register watchdog interface.\n");
-		dev->wd_interface_reg = true;
+		return;
 	}
+
+	dev_dbg(&dev->pdev->dev,
+		"wd: successfully register watchdog interface.\n");
+	dev->wd_interface_reg = true;
+	watchdog_set_drvdata(&amt_wd_dev, dev);
 }
 
 void mei_watchdog_unregister(struct mei_device *dev)
 {
-	if (dev->wd_interface_reg)
-		watchdog_unregister_device(&amt_wd_dev);
+	if (!dev->wd_interface_reg)
+		return;
+
+	watchdog_set_drvdata(&amt_wd_dev, NULL);
+	watchdog_unregister_device(&amt_wd_dev);
 	dev->wd_interface_reg = false;
 }
 

drivers/misc/pch_phub.c

@@ -699,7 +699,7 @@ static int __devinit pch_phub_probe(struct pci_dev *pdev,
 	chip->pch_phub_base_address = pci_iomap(pdev, 1, 0);
 
 
-	if (chip->pch_phub_base_address == 0) {
+	if (chip->pch_phub_base_address == NULL) {
 		dev_err(&pdev->dev, "%s : pci_iomap FAILED", __func__);
 		ret = -ENOMEM;
 		goto err_pci_iomap;
@@ -893,18 +893,7 @@ static struct pci_driver pch_phub_driver = {
 	.resume = pch_phub_resume
 };
 
-static int __init pch_phub_pci_init(void)
-{
-	return pci_register_driver(&pch_phub_driver);
-}
-
-static void __exit pch_phub_pci_exit(void)
-{
-	pci_unregister_driver(&pch_phub_driver);
-}
-
-module_init(pch_phub_pci_init);
-module_exit(pch_phub_pci_exit);
+module_pci_driver(pch_phub_driver);
 
 MODULE_DESCRIPTION("Intel EG20T PCH/LAPIS Semiconductor IOH(ML7213/ML7223) PHUB");
 MODULE_LICENSE("GPL");

drivers/misc/ti-st/st_core.c

@@ -30,11 +30,13 @@
 
 #include <linux/ti_wilink_st.h>
 
+extern void st_kim_recv(void *, const unsigned char *, long);
+void st_int_recv(void *, const unsigned char *, long);
 /* function pointer pointing to either,
  * st_kim_recv during registration to receive fw download responses
  * st_int_recv after registration to receive proto stack responses
  */
-void (*st_recv) (void*, const unsigned char*, long);
+static void (*st_recv) (void *, const unsigned char *, long);
 
 /********************************************************************/
 static void add_channel_to_table(struct st_data_s *st_gdata,
@@ -100,7 +102,7 @@ int st_int_write(struct st_data_s *st_gdata,
  * push the skb received to relevant
  * protocol stacks
  */
-void st_send_frame(unsigned char chnl_id, struct st_data_s *st_gdata)
+static void st_send_frame(unsigned char chnl_id, struct st_data_s *st_gdata)
 {
 	pr_debug(" %s(prot:%d) ", __func__, chnl_id);
 
@@ -140,7 +142,7 @@ void st_send_frame(unsigned char chnl_id, struct st_data_s *st_gdata)
  * This function is being called with spin lock held, protocol drivers are
  * only expected to complete their waits and do nothing more than that.
  */
-void st_reg_complete(struct st_data_s *st_gdata, char err)
+static void st_reg_complete(struct st_data_s *st_gdata, char err)
 {
 	unsigned char i = 0;
 	pr_info(" %s ", __func__);
@@ -379,7 +381,7 @@ void st_int_recv(void *disc_data,
  *	completely, return that skb which has the pending data.
  *	In normal cases, return top of txq.
  */
-struct sk_buff *st_int_dequeue(struct st_data_s *st_gdata)
+static struct sk_buff *st_int_dequeue(struct st_data_s *st_gdata)
 {
 	struct sk_buff *returning_skb;
 
@@ -401,7 +403,7 @@ struct sk_buff *st_int_dequeue(struct st_data_s *st_gdata)
  *	txq and waitq needs protection since the other contexts
  *	may be sending data, waking up chip.
  */
-void st_int_enqueue(struct st_data_s *st_gdata, struct sk_buff *skb)
+static void st_int_enqueue(struct st_data_s *st_gdata, struct sk_buff *skb)
 {
 	unsigned long flags = 0;
 

drivers/misc/ti-st/st_kim.c

@@ -63,10 +63,27 @@ static struct platform_device *st_get_plat_device(int id)
  *	in case of error don't complete so that waiting for proper
  *	response times out
  */
-void validate_firmware_response(struct kim_data_s *kim_gdata)
+static void validate_firmware_response(struct kim_data_s *kim_gdata)
 {
 	struct sk_buff *skb = kim_gdata->rx_skb;
-	if (unlikely(skb->data[5] != 0)) {
+	if (!skb)
+		return;
+
+	/* these magic numbers are the position in the response buffer which
+	 * allows us to distinguish whether the response is for the read
+	 * version info. command
+	 */
+	if (skb->data[2] == 0x01 && skb->data[3] == 0x01 &&
+			skb->data[4] == 0x10 && skb->data[5] == 0x00) {
+		/* fw version response */
+		memcpy(kim_gdata->resp_buffer,
+				kim_gdata->rx_skb->data,
+				kim_gdata->rx_skb->len);
+		complete_all(&kim_gdata->kim_rcvd);
+		kim_gdata->rx_state = ST_W4_PACKET_TYPE;
+		kim_gdata->rx_skb = NULL;
+		kim_gdata->rx_count = 0;
+	} else if (unlikely(skb->data[5] != 0)) {
 		pr_err("no proper response during fw download");
 		pr_err("data6 %x", skb->data[5]);
 		kfree_skb(skb);
@@ -119,7 +136,7 @@ static inline int kim_check_data_len(struct kim_data_s *kim_gdata, int len)
  *	have been observed to come in bursts of different
  *	tty_receive and hence the logic
  */
-void kim_int_recv(struct kim_data_s *kim_gdata,
+static void kim_int_recv(struct kim_data_s *kim_gdata,
 	const unsigned char *data, long count)
 {
 	const unsigned char *ptr;
@@ -207,16 +224,19 @@ static long read_local_version(struct kim_data_s *kim_gdata, char *bts_scr_name)
 		return -EIO;
 	}
 
-	if (!wait_for_completion_timeout
-	    (&kim_gdata->kim_rcvd, msecs_to_jiffies(CMD_RESP_TIME))) {
+	if (!wait_for_completion_interruptible_timeout(
+		&kim_gdata->kim_rcvd, msecs_to_jiffies(CMD_RESP_TIME))) {
 		pr_err(" waiting for ver info- timed out ");
 		return -ETIMEDOUT;
 	}
 	INIT_COMPLETION(kim_gdata->kim_rcvd);
+	/* the positions 12 & 13 in the response buffer provide with the
+	 * chip, major & minor numbers
+	 */
 
 	version =
-		MAKEWORD(kim_gdata->resp_buffer[13],
-				kim_gdata->resp_buffer[14]);
+		MAKEWORD(kim_gdata->resp_buffer[12],
+				kim_gdata->resp_buffer[13]);
 	chip = (version & 0x7C00) >> 10;
 	min_ver = (version & 0x007F);
 	maj_ver = (version & 0x0380) >> 7;
@@ -236,7 +256,7 @@ static long read_local_version(struct kim_data_s *kim_gdata, char *bts_scr_name)
 	return 0;
 }
 
-void skip_change_remote_baud(unsigned char **ptr, long *len)
+static void skip_change_remote_baud(unsigned char **ptr, long *len)
 {
 	unsigned char *nxt_action, *cur_action;
 	cur_action = *ptr;
@@ -370,9 +390,9 @@ static long download_firmware(struct kim_data_s *kim_gdata)
 			break;
 		case ACTION_WAIT_EVENT:  /* wait */
 			pr_debug("W");
-			if (!wait_for_completion_timeout
-					(&kim_gdata->kim_rcvd,
-					 msecs_to_jiffies(CMD_RESP_TIME))) {
+			if (!wait_for_completion_interruptible_timeout(
+					&kim_gdata->kim_rcvd,
+					msecs_to_jiffies(CMD_RESP_TIME))) {
 				pr_err("response timeout during fw download ");
 				/* timed out */
 				release_firmware(kim_gdata->fw_entry);
@@ -410,16 +430,10 @@ void st_kim_recv(void *disc_data, const unsigned char *data, long count)
 	struct st_data_s	*st_gdata = (struct st_data_s *)disc_data;
 	struct kim_data_s	*kim_gdata = st_gdata->kim_data;
 
-	/* copy to local buffer */
-	if (unlikely(data[4] == 0x01 && data[5] == 0x10 && data[0] == 0x04)) {
-		/* must be the read_ver_cmd */
-		memcpy(kim_gdata->resp_buffer, data, count);
-		complete_all(&kim_gdata->kim_rcvd);
-		return;
-	} else {
-		kim_int_recv(kim_gdata, data, count);
-		/* either completes or times out */
-	}
+	/* proceed to gather all data and distinguish read fw version response
+	 * from other fw responses when data gathering is complete
+	 */
+	kim_int_recv(kim_gdata, data, count);
 	return;
 }
 
@@ -454,11 +468,6 @@ long st_kim_start(void *kim_data)
 		if (pdata->chip_enable)
 			pdata->chip_enable(kim_gdata);
 
-		/* Configure BT nShutdown to HIGH state */
-		gpio_set_value(kim_gdata->nshutdown, GPIO_LOW);
-		mdelay(5);	/* FIXME: a proper toggle */
-		gpio_set_value(kim_gdata->nshutdown, GPIO_HIGH);
-		mdelay(100);
 		/* re-initialize the completion */
 		INIT_COMPLETION(kim_gdata->ldisc_installed);
 		/* send notification to UIM */
@@ -467,8 +476,8 @@ long st_kim_start(void *kim_data)
 		sysfs_notify(&kim_gdata->kim_pdev->dev.kobj,
 				NULL, "install");
 		/* wait for ldisc to be installed */
-		err = wait_for_completion_timeout(&kim_gdata->ldisc_installed,
-				msecs_to_jiffies(LDISC_TIME));
+		err = wait_for_completion_interruptible_timeout(
+			&kim_gdata->ldisc_installed, msecs_to_jiffies(LDISC_TIME));
 		if (!err) {
 			/* ldisc installation timeout,
 			 * flush uart, power cycle BT_EN */
@@ -500,8 +509,7 @@ long st_kim_start(void *kim_data)
  *	(b) upon failure to either install ldisc or download firmware.
  *	The function is responsible to (a) notify UIM about un-installation,
  *	(b) flush UART if the ldisc was installed.
- *	(c) reset BT_EN - pull down nshutdown at the end.
- *	(d) invoke platform's chip disabling routine.
+ *	(c) invoke platform's chip disabling routine.
  */
 long st_kim_stop(void *kim_data)
 {
@@ -526,20 +534,13 @@ long st_kim_stop(void *kim_data)
 	sysfs_notify(&kim_gdata->kim_pdev->dev.kobj, NULL, "install");
 
 	/* wait for ldisc to be un-installed */
-	err = wait_for_completion_timeout(&kim_gdata->ldisc_installed,
-			msecs_to_jiffies(LDISC_TIME));
+	err = wait_for_completion_interruptible_timeout(
+		&kim_gdata->ldisc_installed, msecs_to_jiffies(LDISC_TIME));
 	if (!err) {		/* timeout */
 		pr_err(" timed out waiting for ldisc to be un-installed");
-		return -ETIMEDOUT;
+		err = -ETIMEDOUT;
 	}
 
-	/* By default configure BT nShutdown to LOW state */
-	gpio_set_value(kim_gdata->nshutdown, GPIO_LOW);
-	mdelay(1);
-	gpio_set_value(kim_gdata->nshutdown, GPIO_HIGH);
-	mdelay(1);
-	gpio_set_value(kim_gdata->nshutdown, GPIO_LOW);
-
 	/* platform specific disable */
 	if (pdata->chip_disable)
 		pdata->chip_disable(kim_gdata);
@@ -701,7 +702,7 @@ static const struct file_operations list_debugfs_fops = {
  * board-*.c file
  */
 
-struct dentry *kim_debugfs_dir;
+static struct dentry *kim_debugfs_dir;
 static int kim_probe(struct platform_device *pdev)
 {
 	long status;
@@ -731,20 +732,6 @@ static int kim_probe(struct platform_device *pdev)
 	/* refer to itself */
 	kim_gdata->core_data->kim_data = kim_gdata;
 
-	/* Claim the chip enable nShutdown gpio from the system */
-	kim_gdata->nshutdown = pdata->nshutdown_gpio;
-	status = gpio_request(kim_gdata->nshutdown, "kim");
-	if (unlikely(status)) {
-		pr_err(" gpio %ld request failed ", kim_gdata->nshutdown);
-		return status;
-	}
-
-	/* Configure nShutdown GPIO as output=0 */
-	status = gpio_direction_output(kim_gdata->nshutdown, 0);
-	if (unlikely(status)) {
-		pr_err(" unable to configure gpio %ld", kim_gdata->nshutdown);
-		return status;
-	}
 	/* get reference of pdev for request_firmware
 	 */
 	kim_gdata->kim_pdev = pdev;
@@ -780,18 +767,10 @@ static int kim_probe(struct platform_device *pdev)
 
 static int kim_remove(struct platform_device *pdev)
 {
-	/* free the GPIOs requested */
-	struct ti_st_plat_data	*pdata = pdev->dev.platform_data;
 	struct kim_data_s	*kim_gdata;
 
 	kim_gdata = dev_get_drvdata(&pdev->dev);
 
-	/* Free the Bluetooth/FM/GPIO
-	 * nShutdown gpio from the system
-	 */
-	gpio_free(pdata->nshutdown_gpio);
-	pr_info("nshutdown GPIO Freed");
-
 	debugfs_remove_recursive(kim_debugfs_dir);
 	sysfs_remove_group(&pdev->dev.kobj, &uim_attr_grp);
 	pr_info("sysfs entries removed");
@@ -804,7 +783,7 @@ static int kim_remove(struct platform_device *pdev)
 	return 0;
 }
 
-int kim_suspend(struct platform_device *pdev, pm_message_t state)
+static int kim_suspend(struct platform_device *pdev, pm_message_t state)
 {
 	struct ti_st_plat_data	*pdata = pdev->dev.platform_data;
 
@@ -814,7 +793,7 @@ int kim_suspend(struct platform_device *pdev, pm_message_t state)
 	return -EOPNOTSUPP;
 }
 
-int kim_resume(struct platform_device *pdev)
+static int kim_resume(struct platform_device *pdev)
 {
 	struct ti_st_plat_data	*pdata = pdev->dev.platform_data;
 

drivers/w1/masters/Kconfig

@@ -60,7 +60,6 @@ config W1_MASTER_GPIO
 
 config HDQ_MASTER_OMAP
 	tristate "OMAP HDQ driver"
-	depends on ARCH_OMAP2PLUS
 	help
 	  Say Y here if you want support for the 1-wire or HDQ Interface
 	  on an OMAP processor.

drivers/w1/masters/omap_hdq.c

@@ -18,9 +18,6 @@
 #include <linux/sched.h>
 #include <linux/pm_runtime.h>
 
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
 #include "../w1.h"
 #include "../w1_int.h"
 
@@ -73,11 +70,11 @@ struct hdq_data {
 };
 
 static int __devinit omap_hdq_probe(struct platform_device *pdev);
-static int omap_hdq_remove(struct platform_device *pdev);
+static int __devexit omap_hdq_remove(struct platform_device *pdev);
 
 static struct platform_driver omap_hdq_driver = {
 	.probe =	omap_hdq_probe,
-	.remove =	omap_hdq_remove,
+	.remove =	__devexit_p(omap_hdq_remove),
 	.driver =	{
 		.name =	"omap_hdq",
 	},
@@ -538,39 +535,35 @@ static void omap_w1_write_byte(void *_hdq, u8 byte)
 		hdq_data->init_trans = 0;
 		mutex_unlock(&hdq_data->hdq_mutex);
 	}
-
-	return;
 }
 
 static int __devinit omap_hdq_probe(struct platform_device *pdev)
 {
+	struct device *dev = &pdev->dev;
 	struct hdq_data *hdq_data;
 	struct resource *res;
 	int ret, irq;
 	u8 rev;
 
-	hdq_data = kmalloc(sizeof(*hdq_data), GFP_KERNEL);
+	hdq_data = devm_kzalloc(dev, sizeof(*hdq_data), GFP_KERNEL);
 	if (!hdq_data) {
 		dev_dbg(&pdev->dev, "unable to allocate memory\n");
-		ret = -ENOMEM;
-		goto err_kmalloc;
+		return -ENOMEM;
 	}
 
-	hdq_data->dev = &pdev->dev;
+	hdq_data->dev = dev;
 	platform_set_drvdata(pdev, hdq_data);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
 		dev_dbg(&pdev->dev, "unable to get resource\n");
-		ret = -ENXIO;
-		goto err_resource;
+		return -ENXIO;
 	}
 
-	hdq_data->hdq_base = ioremap(res->start, SZ_4K);
+	hdq_data->hdq_base = devm_request_and_ioremap(dev, res);
 	if (!hdq_data->hdq_base) {
 		dev_dbg(&pdev->dev, "ioremap failed\n");
-		ret = -EINVAL;
-		goto err_ioremap;
+		return -ENOMEM;
 	}
 
 	hdq_data->hdq_usecount = 0;
@@ -591,7 +584,8 @@ static int __devinit omap_hdq_probe(struct platform_device *pdev)
 		goto err_irq;
 	}
 
-	ret = request_irq(irq, hdq_isr, IRQF_DISABLED, "omap_hdq", hdq_data);
+	ret = devm_request_irq(dev, irq, hdq_isr, IRQF_DISABLED,
+			"omap_hdq", hdq_data);
 	if (ret < 0) {
 		dev_dbg(&pdev->dev, "could not request irq\n");
 		goto err_irq;
@@ -616,19 +610,10 @@ static int __devinit omap_hdq_probe(struct platform_device *pdev)
 err_w1:
 	pm_runtime_disable(&pdev->dev);
 
-	iounmap(hdq_data->hdq_base);
-
-err_ioremap:
-err_resource:
-	platform_set_drvdata(pdev, NULL);
-	kfree(hdq_data);
-
-err_kmalloc:
 	return ret;
-
 }
 
-static int omap_hdq_remove(struct platform_device *pdev)
+static int __devexit omap_hdq_remove(struct platform_device *pdev)
 {
 	struct hdq_data *hdq_data = platform_get_drvdata(pdev);
 
@@ -644,27 +629,11 @@ static int omap_hdq_remove(struct platform_device *pdev)
 
 	/* remove module dependency */
 	pm_runtime_disable(&pdev->dev);
-	free_irq(INT_24XX_HDQ_IRQ, hdq_data);
-	platform_set_drvdata(pdev, NULL);
-	iounmap(hdq_data->hdq_base);
-	kfree(hdq_data);
 
 	return 0;
 }
 
-static int __init
-omap_hdq_init(void)
-{
-	return platform_driver_register(&omap_hdq_driver);
-}
-module_init(omap_hdq_init);
-
-static void __exit
-omap_hdq_exit(void)
-{
-	platform_driver_unregister(&omap_hdq_driver);
-}
-module_exit(omap_hdq_exit);
+module_platform_driver(omap_hdq_driver);
 
 module_param(w1_id, int, S_IRUSR);
 MODULE_PARM_DESC(w1_id, "1-wire id for the slave detection");

drivers/w1/masters/w1-gpio.c

@@ -14,6 +14,8 @@
 #include <linux/slab.h>
 #include <linux/w1-gpio.h>
 #include <linux/gpio.h>
+#include <linux/of_platform.h>
+#include <linux/of_gpio.h>
 
 #include "../w1.h"
 #include "../w1_int.h"
@@ -42,12 +44,55 @@ static u8 w1_gpio_read_bit(void *data)
 	return gpio_get_value(pdata->pin) ? 1 : 0;
 }
 
+#ifdef CONFIG_OF
+static struct of_device_id w1_gpio_dt_ids[] = {
+	{ .compatible = "w1-gpio" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, w1_gpio_dt_ids);
+
+static int w1_gpio_probe_dt(struct platform_device *pdev)
+{
+	struct w1_gpio_platform_data *pdata = pdev->dev.platform_data;
+	struct device_node *np = pdev->dev.of_node;
+	const struct of_device_id *of_id =
+			of_match_device(w1_gpio_dt_ids, &pdev->dev);
+
+	if (!of_id)
+		return 0;
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	if (of_get_property(np, "linux,open-drain", NULL))
+		pdata->is_open_drain = 1;
+
+	pdata->pin = of_get_gpio(np, 0);
+	pdata->ext_pullup_enable_pin = of_get_gpio(np, 1);
+	pdev->dev.platform_data = pdata;
+
+	return 0;
+}
+#else
+static int w1_gpio_probe_dt(struct platform_device *pdev)
+{
+	return 0;
+}
+#endif
+
 static int __init w1_gpio_probe(struct platform_device *pdev)
 {
 	struct w1_bus_master *master;
-	struct w1_gpio_platform_data *pdata = pdev->dev.platform_data;
+	struct w1_gpio_platform_data *pdata;
 	int err;
 
+	err = w1_gpio_probe_dt(pdev);
+	if (err < 0)
+		return err;
+
+	pdata = pdev->dev.platform_data;
+
 	if (!pdata)
 		return -ENXIO;
 
@@ -59,6 +104,13 @@ static int __init w1_gpio_probe(struct platform_device *pdev)
 	if (err)
 		goto free_master;
 
+	if (gpio_is_valid(pdata->ext_pullup_enable_pin)) {
+		err = gpio_request_one(pdata->ext_pullup_enable_pin,
+				       GPIOF_INIT_LOW, "w1 pullup");
+		if (err < 0)
+			goto free_gpio;
+	}
+
 	master->data = pdata;
 	master->read_bit = w1_gpio_read_bit;
 
@@ -72,15 +124,21 @@ static int __init w1_gpio_probe(struct platform_device *pdev)
 
 	err = w1_add_master_device(master);
 	if (err)
-		goto free_gpio;
+		goto free_gpio_ext_pu;
 
 	if (pdata->enable_external_pullup)
 		pdata->enable_external_pullup(1);
 
+	if (gpio_is_valid(pdata->ext_pullup_enable_pin))
+		gpio_set_value(pdata->ext_pullup_enable_pin, 1);
+
 	platform_set_drvdata(pdev, master);
 
 	return 0;
 
+ free_gpio_ext_pu:
+	if (gpio_is_valid(pdata->ext_pullup_enable_pin))
+		gpio_free(pdata->ext_pullup_enable_pin);
  free_gpio:
 	gpio_free(pdata->pin);
  free_master:
@@ -97,6 +155,9 @@ static int __exit w1_gpio_remove(struct platform_device *pdev)
 	if (pdata->enable_external_pullup)
 		pdata->enable_external_pullup(0);
 
+	if (gpio_is_valid(pdata->ext_pullup_enable_pin))
+		gpio_set_value(pdata->ext_pullup_enable_pin, 0);
+
 	w1_remove_master_device(master);
 	gpio_free(pdata->pin);
 	kfree(master);
@@ -135,6 +196,7 @@ static struct platform_driver w1_gpio_driver = {
 	.driver = {
 		.name	= "w1-gpio",
 		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(w1_gpio_dt_ids),
 	},
 	.remove	= __exit_p(w1_gpio_remove),
 	.suspend = w1_gpio_suspend,

include/linux/ti_wilink_st.h

@@ -281,9 +281,10 @@ struct kim_data_s {
 long st_kim_start(void *);
 long st_kim_stop(void *);
 
-void st_kim_recv(void *, const unsigned char *, long count);
 void st_kim_complete(void *);
 void kim_st_list_protocols(struct st_data_s *, void *);
+void st_kim_recv(void *, const unsigned char *, long);
+
 
 /*
  * BTS headers

include/linux/w1-gpio.h

@@ -19,6 +19,7 @@ struct w1_gpio_platform_data {
 	unsigned int pin;
 	unsigned int is_open_drain:1;
 	void (*enable_external_pullup)(int enable);
+	unsigned int ext_pullup_enable_pin;
 };
 
 #endif /* _LINUX_W1_GPIO_H */