Merge branch 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes

* 'at91-fixes' of git://github.com/at91linux/linux-at91:
  ARM: at91: dt: remove unit-address part for memory nodes
  ARM: at91: fix check of valid GPIO for SPI and USB
  USB: ehci-atmel: add needed of.h header file
  ARM: at91/NAND DT bindings: add comments
  ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
  USB: ohci-at91: trivial return code name change
  USB: ohci-at91: change maximum number of ports
  USB: ohci-at91: rework and fix initialization
  ARM: at91/dts: USB host vbus is active low
  ARM: at91/USB host: specify and handle properly vbus_pin_active_low
  USB: ohci-at91: fix vbus_pin_active_low handling
  ARM: at91/at91sam9x5: add clkdev entries for DMA controllers

Documentation/devicetree/bindings/mtd/atmel-nand.txt

@@ -27,13 +27,13 @@ nand0: nand@40000000,0 {
 	reg = <0x40000000 0x10000000
 	       0xffffe800 0x200
 	      >;
-	atmel,nand-addr-offset = <21>;
-	atmel,nand-cmd-offset = <22>;
+	atmel,nand-addr-offset = <21>;	/* ale */
+	atmel,nand-cmd-offset = <22>;	/* cle */
 	nand-on-flash-bbt;
 	nand-ecc-mode = "soft";
-	gpios = <&pioC 13 0
-		 &pioC 14 0
-		 0
+	gpios = <&pioC 13 0	/* rdy */
+		 &pioC 14 0 	/* nce */
+		 0		/* cd */
 		>;
 	partition@0 {
 		...

arch/arm/boot/dts/at91sam9g20.dtsi

@@ -35,7 +35,7 @@ cpu@0 {
 		};
 	};
 
-	memory@20000000 {
+	memory {
 		reg = <0x20000000 0x08000000>;
 	};
 

arch/arm/boot/dts/at91sam9g25ek.dts

@@ -37,8 +37,8 @@ macb0: ethernet@f802c000 {
 		usb0: ohci@00600000 {
 			status = "okay";
 			num-ports = <2>;
-			atmel,vbus-gpio = <&pioD 19 0
-					   &pioD 20 0
+			atmel,vbus-gpio = <&pioD 19 1
+					   &pioD 20 1
 					  >;
 		};
 

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -36,7 +36,7 @@ cpu@0 {
 		};
 	};
 
-	memory@70000000 {
+	memory {
 		reg = <0x70000000 0x10000000>;
 	};
 

arch/arm/boot/dts/at91sam9m10g45ek.dts

@@ -17,7 +17,7 @@ chosen {
 		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
 	};
 
-	memory@70000000 {
+	memory {
 		reg = <0x70000000 0x4000000>;
 	};
 
@@ -73,8 +73,8 @@ data@4000000 {
 		usb0: ohci@00700000 {
 			status = "okay";
 			num-ports = <2>;
-			atmel,vbus-gpio = <&pioD 1 0
-					   &pioD 3 0>;
+			atmel,vbus-gpio = <&pioD 1 1
+					   &pioD 3 1>;
 		};
 
 		usb1: ehci@00800000 {

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -34,7 +34,7 @@ cpu@0 {
 		};
 	};
 
-	memory@20000000 {
+	memory {
 		reg = <0x20000000 0x10000000>;
 	};
 
@@ -201,8 +201,8 @@ nand0: nand@40000000 {
 			      >;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
-			gpios = <&pioC 8 0
-				 &pioC 14 0
+			gpios = <&pioD 5 0
+				 &pioD 4 0
 				 0
 				>;
 			status = "disabled";

arch/arm/boot/dts/at91sam9x5cm.dtsi

@@ -8,7 +8,7 @@
  */
 
 / {
-	memory@20000000 {
+	memory {
 		reg = <0x20000000 0x8000000>;
 	};
 

arch/arm/boot/dts/usb_a9g20.dts

@@ -16,7 +16,7 @@ chosen {
 		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
 	};
 
-	memory@20000000 {
+	memory {
 		reg = <0x20000000 0x4000000>;
 	};
 

arch/arm/mach-at91/at91sam9260_devices.c

@@ -598,6 +598,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		else
 			cs_pin = spi1_standard_cs[devices[i].chip_select];
 
+		if (!gpio_is_valid(cs_pin))
+			continue;
+
 		if (devices[i].bus_num == 0)
 			enable_spi0 = 1;
 		else

arch/arm/mach-at91/at91sam9261_devices.c

@@ -415,6 +415,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		else
 			cs_pin = spi1_standard_cs[devices[i].chip_select];
 
+		if (!gpio_is_valid(cs_pin))
+			continue;
+
 		if (devices[i].bus_num == 0)
 			enable_spi0 = 1;
 		else

arch/arm/mach-at91/at91sam9263_devices.c

@@ -72,7 +72,8 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
 		if (gpio_is_valid(data->vbus_pin[i]))
-			at91_set_gpio_output(data->vbus_pin[i], 0);
+			at91_set_gpio_output(data->vbus_pin[i],
+					     data->vbus_pin_active_low[i]);
 	}
 
 	/* Enable overcurrent notification */
@@ -671,6 +672,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		else
 			cs_pin = spi1_standard_cs[devices[i].chip_select];
 
+		if (!gpio_is_valid(cs_pin))
+			continue;
+
 		if (devices[i].bus_num == 0)
 			enable_spi0 = 1;
 		else

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -127,12 +127,13 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
 		if (gpio_is_valid(data->vbus_pin[i]))
-			at91_set_gpio_output(data->vbus_pin[i], 0);
+			at91_set_gpio_output(data->vbus_pin[i],
+					     data->vbus_pin_active_low[i]);
 	}
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}
 
@@ -188,7 +189,8 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
 		if (gpio_is_valid(data->vbus_pin[i]))
-			at91_set_gpio_output(data->vbus_pin[i], 0);
+			at91_set_gpio_output(data->vbus_pin[i],
+					     data->vbus_pin_active_low[i]);
 	}
 
 	usbh_ehci_data = *data;
@@ -785,6 +787,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		else
 			cs_pin = spi1_standard_cs[devices[i].chip_select];
 
+		if (!gpio_is_valid(cs_pin))
+			continue;
+
 		if (devices[i].bus_num == 0)
 			enable_spi0 = 1;
 		else

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -419,6 +419,9 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		else
 			cs_pin = spi_standard_cs[devices[i].chip_select];
 
+		if (!gpio_is_valid(cs_pin))
+			continue;
+
 		/* enable chip-select pin */
 		at91_set_gpio_output(cs_pin, 1);
 

arch/arm/mach-at91/at91sam9x5.c

@@ -223,6 +223,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("usart", "f8028000.serial", &usart3_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb0_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb0_clk),
+	CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma0_clk),
+	CLKDEV_CON_DEV_ID("dma_clk", "ffffee00.dma-controller", &dma1_clk),
 	CLKDEV_CON_ID("pioA", &pioAB_clk),
 	CLKDEV_CON_ID("pioB", &pioAB_clk),
 	CLKDEV_CON_ID("pioC", &pioCD_clk),

arch/arm/mach-at91/board-sam9263ek.c

@@ -74,6 +74,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
 	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.vbus_pin_active_low = {1, 1},
 	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -71,6 +71,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_hs_data = {
 	.ports		= 2,
 	.vbus_pin	= {AT91_PIN_PD1, AT91_PIN_PD3},
+	.vbus_pin_active_low = {1, 1},
 	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 

arch/arm/mach-at91/include/mach/board.h

@@ -86,14 +86,15 @@ extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *d
 extern void __init at91_add_device_eth(struct macb_platform_data *data);
 
  /* USB Host */
+#define AT91_MAX_USBH_PORTS	3
 struct at91_usbh_data {
+	int		vbus_pin[AT91_MAX_USBH_PORTS];	/* port power-control pin */
+	int             overcurrent_pin[AT91_MAX_USBH_PORTS];
 	u8		ports;				/* number of ports on root hub */
-	int		vbus_pin[2];	/* port power-control pin */
-	u8              vbus_pin_active_low[2];
 	u8              overcurrent_supported;
-	int             overcurrent_pin[2];
-	u8              overcurrent_status[2];
-	u8              overcurrent_changed[2];
+	u8              vbus_pin_active_low[AT91_MAX_USBH_PORTS];
+	u8              overcurrent_status[AT91_MAX_USBH_PORTS];
+	u8              overcurrent_changed[AT91_MAX_USBH_PORTS];
 };
 extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
 extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data);

drivers/usb/host/ehci-atmel.c

@@ -13,6 +13,7 @@
 
 #include <linux/clk.h>
 #include <linux/platform_device.h>
+#include <linux/of.h>
 #include <linux/of_platform.h>
 
 /* interface and function clocks */

drivers/usb/host/ohci-at91.c

@@ -27,6 +27,10 @@
 #error "CONFIG_ARCH_AT91 must be defined."
 #endif
 
+#define valid_port(index)	((index) >= 0 && (index) < AT91_MAX_USBH_PORTS)
+#define at91_for_each_port(index)	\
+		for ((index) = 0; (index) < AT91_MAX_USBH_PORTS; (index)++)
+
 /* interface and function clocks; sometimes also an AHB clock */
 static struct clk *iclk, *fclk, *hclk;
 static int clocked;
@@ -240,26 +244,26 @@ ohci_at91_start (struct usb_hcd *hcd)
 
 static void ohci_at91_usb_set_power(struct at91_usbh_data *pdata, int port, int enable)
 {
-	if (port < 0 || port >= 2)
+	if (!valid_port(port))
 		return;
 
 	if (!gpio_is_valid(pdata->vbus_pin[port]))
 		return;
 
 	gpio_set_value(pdata->vbus_pin[port],
-		       !pdata->vbus_pin_active_low[port] ^ enable);
+		       pdata->vbus_pin_active_low[port] ^ enable);
 }
 
 static int ohci_at91_usb_get_power(struct at91_usbh_data *pdata, int port)
 {
-	if (port < 0 || port >= 2)
+	if (!valid_port(port))
 		return -EINVAL;
 
 	if (!gpio_is_valid(pdata->vbus_pin[port]))
 		return -EINVAL;
 
 	return gpio_get_value(pdata->vbus_pin[port]) ^
-		!pdata->vbus_pin_active_low[port];
+		pdata->vbus_pin_active_low[port];
 }
 
 /*
@@ -271,9 +275,9 @@ static int ohci_at91_hub_status_data(struct usb_hcd *hcd, char *buf)
 	int length = ohci_hub_status_data(hcd, buf);
 	int port;
 
-	for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) {
+	at91_for_each_port(port) {
 		if (pdata->overcurrent_changed[port]) {
-			if (! length)
+			if (!length)
 				length = 1;
 			buf[0] |= 1 << (port + 1);
 		}
@@ -297,11 +301,17 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 		"ohci_at91_hub_control(%p,0x%04x,0x%04x,0x%04x,%p,%04x)\n",
 		hcd, typeReq, wValue, wIndex, buf, wLength);
 
+	wIndex--;
+
 	switch (typeReq) {
 	case SetPortFeature:
 		if (wValue == USB_PORT_FEAT_POWER) {
 			dev_dbg(hcd->self.controller, "SetPortFeat: POWER\n");
-			ohci_at91_usb_set_power(pdata, wIndex - 1, 1);
+			if (valid_port(wIndex)) {
+				ohci_at91_usb_set_power(pdata, wIndex, 1);
+				ret = 0;
+			}
+
 			goto out;
 		}
 		break;
@@ -312,9 +322,9 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 			dev_dbg(hcd->self.controller,
 				"ClearPortFeature: C_OVER_CURRENT\n");
 
-			if (wIndex == 1 || wIndex == 2) {
-				pdata->overcurrent_changed[wIndex-1] = 0;
-				pdata->overcurrent_status[wIndex-1] = 0;
+			if (valid_port(wIndex)) {
+				pdata->overcurrent_changed[wIndex] = 0;
+				pdata->overcurrent_status[wIndex] = 0;
 			}
 
 			goto out;
@@ -323,9 +333,8 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 			dev_dbg(hcd->self.controller,
 				"ClearPortFeature: OVER_CURRENT\n");
 
-			if (wIndex == 1 || wIndex == 2) {
-				pdata->overcurrent_status[wIndex-1] = 0;
-			}
+			if (valid_port(wIndex))
+				pdata->overcurrent_status[wIndex] = 0;
 
 			goto out;
 
@@ -333,15 +342,15 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 			dev_dbg(hcd->self.controller,
 				"ClearPortFeature: POWER\n");
 
-			if (wIndex == 1 || wIndex == 2) {
-				ohci_at91_usb_set_power(pdata, wIndex - 1, 0);
+			if (valid_port(wIndex)) {
+				ohci_at91_usb_set_power(pdata, wIndex, 0);
 				return 0;
 			}
 		}
 		break;
 	}
 
-	ret = ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
+	ret = ohci_hub_control(hcd, typeReq, wValue, wIndex + 1, buf, wLength);
 	if (ret)
 		goto out;
 
@@ -377,20 +386,17 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 
 		dev_dbg(hcd->self.controller, "GetPortStatus(%d)\n", wIndex);
 
-		if (wIndex == 1 || wIndex == 2) {
-			if (! ohci_at91_usb_get_power(pdata, wIndex-1)) {
+		if (valid_port(wIndex)) {
+			if (!ohci_at91_usb_get_power(pdata, wIndex))
 				*data &= ~cpu_to_le32(RH_PS_PPS);
-			}
 
-			if (pdata->overcurrent_changed[wIndex-1]) {
+			if (pdata->overcurrent_changed[wIndex])
 				*data |= cpu_to_le32(RH_PS_OCIC);
-			}
 
-			if (pdata->overcurrent_status[wIndex-1]) {
+			if (pdata->overcurrent_status[wIndex])
 				*data |= cpu_to_le32(RH_PS_POCI);
 		}
 	}
-	}
 
  out:
 	return ret;
@@ -450,14 +456,14 @@ static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data)
 
 	/* From the GPIO notifying the over-current situation, find
 	 * out the corresponding port */
-	for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) {
+	at91_for_each_port(port) {
 		if (gpio_to_irq(pdata->overcurrent_pin[port]) == irq) {
 			gpio = pdata->overcurrent_pin[port];
 			break;
 		}
 	}
 
-	if (port == ARRAY_SIZE(pdata->overcurrent_pin)) {
+	if (port == AT91_MAX_USBH_PORTS) {
 		dev_err(& pdev->dev, "overcurrent interrupt from unknown GPIO\n");
 		return IRQ_HANDLED;
 	}
@@ -467,7 +473,7 @@ static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data)
 	/* When notified of an over-current situation, disable power
 	   on the corresponding port, and mark this port in
 	   over-current. */
-	if (! val) {
+	if (!val) {
 		ohci_at91_usb_set_power(pdata, port, 0);
 		pdata->overcurrent_status[port]  = 1;
 		pdata->overcurrent_changed[port] = 1;
@@ -492,7 +498,7 @@ static u64 at91_ohci_dma_mask = DMA_BIT_MASK(32);
 static int __devinit ohci_at91_of_init(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
-	int i, ret, gpio;
+	int i, gpio;
 	enum of_gpio_flags flags;
 	struct at91_usbh_data	*pdata;
 	u32 ports;
@@ -514,48 +520,17 @@ static int __devinit ohci_at91_of_init(struct platform_device *pdev)
 	if (!of_property_read_u32(np, "num-ports", &ports))
 		pdata->ports = ports;
 
-	for (i = 0; i < 2; i++) {
+	at91_for_each_port(i) {
 		gpio = of_get_named_gpio_flags(np, "atmel,vbus-gpio", i, &flags);
 		pdata->vbus_pin[i] = gpio;
 		if (!gpio_is_valid(gpio))
 			continue;
 		pdata->vbus_pin_active_low[i] = flags & OF_GPIO_ACTIVE_LOW;
-		ret = gpio_request(gpio, "ohci_vbus");
-		if (ret) {
-			dev_warn(&pdev->dev, "can't request vbus gpio %d", gpio);
-			continue;
-		}
-		ret = gpio_direction_output(gpio, !(flags & OF_GPIO_ACTIVE_LOW) ^ 1);
-		if (ret)
-			dev_warn(&pdev->dev, "can't put vbus gpio %d as output %d",
-				 !(flags & OF_GPIO_ACTIVE_LOW) ^ 1, gpio);
 	}
 
-	for (i = 0; i < 2; i++) {
-		gpio = of_get_named_gpio_flags(np, "atmel,oc-gpio", i, &flags);
-		pdata->overcurrent_pin[i] = gpio;
-		if (!gpio_is_valid(gpio))
-			continue;
-		ret = gpio_request(gpio, "ohci_overcurrent");
-		if (ret) {
-			dev_err(&pdev->dev, "can't request overcurrent gpio %d", gpio);
-			continue;
-		}
-
-		ret = gpio_direction_input(gpio);
-		if (ret) {
-			dev_err(&pdev->dev, "can't configure overcurrent gpio %d as input", gpio);
-			continue;
-		}
-
-		ret = request_irq(gpio_to_irq(gpio),
-				  ohci_hcd_at91_overcurrent_irq,
-				  IRQF_SHARED, "ohci_overcurrent", pdev);
-		if (ret) {
-			gpio_free(gpio);
-			dev_warn(& pdev->dev, "cannot get GPIO IRQ for overcurrent\n");
-		}
-	}
+	at91_for_each_port(i)
+		pdata->overcurrent_pin[i] =
+			of_get_named_gpio_flags(np, "atmel,oc-gpio", i, &flags);
 
 	pdev->dev.platform_data = pdata;
 
@@ -574,35 +549,69 @@ static int ohci_hcd_at91_drv_probe(struct platform_device *pdev)
 {
 	struct at91_usbh_data	*pdata;
 	int			i;
+	int			gpio;
+	int			ret;
 
-	i = ohci_at91_of_init(pdev);
-
-	if (i)
-		return i;
+	ret = ohci_at91_of_init(pdev);
+	if (ret)
+		return ret;
 
 	pdata = pdev->dev.platform_data;
 
 	if (pdata) {
-		for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
+		at91_for_each_port(i) {
 			if (!gpio_is_valid(pdata->vbus_pin[i]))
 				continue;
-			gpio_request(pdata->vbus_pin[i], "ohci_vbus");
-			ohci_at91_usb_set_power(pdata, i, 1);
+			gpio = pdata->vbus_pin[i];
+
+			ret = gpio_request(gpio, "ohci_vbus");
+			if (ret) {
+				dev_err(&pdev->dev,
+					"can't request vbus gpio %d\n", gpio);
+				continue;
+			}
+			ret = gpio_direction_output(gpio,
+						!pdata->vbus_pin_active_low[i]);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"can't put vbus gpio %d as output %d\n",
+					gpio, !pdata->vbus_pin_active_low[i]);
+				gpio_free(gpio);
+				continue;
 			}
 
-		for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) {
-			int ret;
+			ohci_at91_usb_set_power(pdata, i, 1);
+		}
 
+		at91_for_each_port(i) {
 			if (!gpio_is_valid(pdata->overcurrent_pin[i]))
 				continue;
-			gpio_request(pdata->overcurrent_pin[i], "ohci_overcurrent");
+			gpio = pdata->overcurrent_pin[i];
+
+			ret = gpio_request(gpio, "ohci_overcurrent");
+			if (ret) {
+				dev_err(&pdev->dev,
+					"can't request overcurrent gpio %d\n",
+					gpio);
+				continue;
+			}
 
-			ret = request_irq(gpio_to_irq(pdata->overcurrent_pin[i]),
+			ret = gpio_direction_input(gpio);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"can't configure overcurrent gpio %d as input\n",
+					gpio);
+				gpio_free(gpio);
+				continue;
+			}
+
+			ret = request_irq(gpio_to_irq(gpio),
 					  ohci_hcd_at91_overcurrent_irq,
 					  IRQF_SHARED, "ohci_overcurrent", pdev);
 			if (ret) {
-				gpio_free(pdata->overcurrent_pin[i]);
-				dev_warn(& pdev->dev, "cannot get GPIO IRQ for overcurrent\n");
+				gpio_free(gpio);
+				dev_err(&pdev->dev,
+					"can't get gpio IRQ for overcurrent\n");
 			}
 		}
 	}
@@ -617,14 +626,14 @@ static int ohci_hcd_at91_drv_remove(struct platform_device *pdev)
 	int			i;
 
 	if (pdata) {
-		for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
+		at91_for_each_port(i) {
 			if (!gpio_is_valid(pdata->vbus_pin[i]))
 				continue;
 			ohci_at91_usb_set_power(pdata, i, 0);
 			gpio_free(pdata->vbus_pin[i]);
 		}
 
-		for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) {
+		at91_for_each_port(i) {
 			if (!gpio_is_valid(pdata->overcurrent_pin[i]))
 				continue;
 			free_irq(gpio_to_irq(pdata->overcurrent_pin[i]), pdev);